Heat Transfer, Combustion Commons^™

The Improvement Of The Solar Air Heater Duct By Wired Ribs Utilization, Osamah Raad Skheel Alkhafaji

Karbala International Journal of Modern Science

Abstract Heat transfer coefficient of the solar air heater duct (SAH) is low due increasing the thermal performance of its absorber. The present study tends to enhance the thermal characteristics of the SAH by adopting the wired ribs on the absorber under different ribs dimensions and arrangements. A rectangular duct is used to form the SAH with length L=1500mm, width w=100mm and height H=30mm. The used heat fluxes over the absorber are 1000W/m2 and 500W/m2 while the operated Reynolds number range is 708 ~ 6375. The utilized wired ribs are arranged over the absorber so as to develop a relative …

Quantification Of Heat Flows Through Building Entrance Doors On A Winter Day, Daeho Kang

Publications and Research

The current methods for the prediction of the heat flow through building entrance doors have been used for years while involved with a certain degree of uncertainty. This paper describes an experimental method that accurately quantified such heat flow. The experiment monitored local environmental parameters in a college building on a cold winter day. The results of the experiment demonstrated that the experimental method is viable to accurately estimate the heat flow throughout the entrance doors and the presence of a vestibule moderated heat losses from the conditioned area. The results will be used for validating the existing methods.

Competence Of A Spray Passive Down-Draft Evaporative Cooling (Pdec) System For Space Cooling, Daeho Kang, Richard K. Strand

Publications and Research

A spray PDEC system has been relatively less considered than other passive cooling strategies as one of the viable low-energy solutions in the cooling of buildings while having a great potential in energy savings. This study is intended to evaluate the capability of a spray PDEC system for space cooling. It comprises four simulation scenarios to see the system response and influence of indoor thermal environment when a spray PDEC system is adopted as a primary cooling system in two different climates. The simulation results show that a spray PDEC system causes a substantial variation in the indoor thermal environment …

A Techno-Economic Analysis Of Current Cooling Techniques In Irish Data Centres, Lee Gibbons, Bryan Coyne, David Kennedy, Sajad Alimohammadi

Articles

This research is part of a comprehensive study to determine reformative actions for cooling regimes within the Irish data centre market. To achieve this goal, preliminary Exergy, Entropy change and operational cost analyses are used. It is determined that there is no clear advantage for using one cooling method over another without knowing the data centres secondary function (e.g. district heating, energy generation). Air cooling technology is a good candidate for a highly reliable system due to the low exhaust temperatures of 30°C. Two-phase immersion is a possibility for economically viable data centres where operational costs are to be minimised, …

Computational Studies Of Thermal Properties And Desalination Performance Of Low-Dimensional Materials, Yang Hong

Department of Chemistry: Dissertations, Theses, and Student Research

During the last 30 years, microelectronic devices have been continuously designed and developed with smaller size and yet more functionalities. Today, hundreds of millions of transistors and complementary metal-oxide-semiconductor cells can be designed and integrated on a single microchip through 3D packaging and chip stacking technology. A large amount of heat will be generated in a limited space during the operation of microchips. Moreover, there is a high possibility of hot spots due to non-uniform integrated circuit design patterns as some core parts of a microchip work harder than other memory parts. This issue becomes acute as stacked microchips get …

Energy Transformation And Conservation Investigation, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use a thermoelectric generator module to analyze the relationship between thermal and electrical energies. Using data collection sensors and analysis software, students will investigate the relationship between the temperature gradient across a thermoelectric generator module and the resulting electrical potential. Students will then use their data and analysis to solve problems relating to waste thermal energy in electrical systems and communicate their work to their peers and teacher.

Graphs And Cad: Analyzing The Experience Of A Mechanical Engineering Intern, Matthew Des Biens

Celebration of Learning

A reflection on the experiences of a mechanical engineering intern at Bergstrom Inc., this presentation, by Senior Matt Des Biens, will discuss what it was like working for a manufacturing and design company making HVAC units for large customers across the world. The highlights will be on the projects he worked on, the things that he learned, and his views on working for the company as a whole.

Biomethane Production From Distillery Wastewater, Zachary Christman

Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research

Distillery wastewater treatment is a great ecological problem, for example, India produces 2.7 billion liters of alcohol that results in 40 billion liters of wastewater. However, this material can be seen as a resource since 11 million cubic meters of biogas at 60% methane could be produced in addition to cleaning the water. The distillery has two options of what to do with the biogas. The first is to use the biogas to fuel the distillery making the production plant more energy efficient and removing some of the need to buy natural gas. The other is to upgrade the biogas …

Atmospheric Water Harvesting: An Experimental Study Of Viability And The Influence Of Surface Geometry, Orientation, And Drainage, Carson T. Hand

Master's Theses

Fresh water collection techniques have gained significant attention due to global dwindling of fresh water resources and recent scares such as the 2011-2017 California drought. This project explores the economic viability of actively harvesting water from fog, and techniques to maximize water collection. Vapor compression and thermoelectric cooling based dehumidifier prototypes are tested in a series of experiments to assess water collection capability in foggy environments, and what parameters can increase that capability. This testing shows an approximate maximum collection rate of 1.25 L/kWh for the vapor compression prototype, and 0.32 L/kWh for the thermoelectric cooling prototype; compared to 315 …

Surface Engineering Solutions For Immersion Phase Change Cooling Of Electronics, Brendon M. Doran

Master's Theses

Micro- and nano-scale surface modifications have been a subject of great interest for enhancing the pool boiling heat transfer performance of immersion cooling systems due to their ability to augment surface area, improve wickability, and increase nucleation site density. However, many of the surface modification technologies that have been previously demonstrated show a lack of evidence concerning scalability for use at an industrial level. In this work, the pool boiling heat transfer performance of nanoporous anodic aluminum oxide (AAO) films, copper oxide (CuO) nanostructure coatings, and 1D roll-molded microfin arrays has been studied. Each of these technologies possess scalability in …

Modeling The Effect Of A Compartment Fire On Spaces Adjacent To A Bulkhead With And Without Attachments, Carl E. Hendrickson Ii

LSU New Orleans Theses and Dissertations

Structural fire protection is an integral component of shipboard fire safety. There are national and international regulations that delineate requirements for the insulation placed throughout ships. The attachments that penetrate the insulation for hanging wires and pipes can disrupt the integrity of the division, and cause a failure to adhere to the regulations. This problem will be analyzed by using a simplified lumped capacitance model and ANSYS FLUENT CFD. A standard time-temperature fire curve is applied to the fire side of the enclosure. The thermal conductivity of the insulation and steel are made to be temperature dependent. The density of …

Repurposing Plastic Waste In El Cercado, Joseph Dooling, Kirby Townsend, Brendan Smith

Honors Thesis

This project aims to assist the community of El Cercado in the Dominican Republic in turning their plastic waste into useful products. The design team developed a first iteration shredder, injector, and aluminum mold which future design teams could further iterate in order to make products out of waste plastic. Different products were researched to ensure that they can be sold or used in the community. The goal of producing these items is to stimulate economic activity in the community by creating economic opportunity. The design shall also be sustainable in three ways. It shall reuse plastic waste while also …

Insulated Solar Electric Cooker With Phase Change Thermal Storage Medium, Justin Brett Unger, Nathan Robert Christler, Matthew Weeman, Marcus Edward Strutz

Mechanical Engineering

This final design review document outlines the senior design project carried out by a team of four mechanical engineering students at the California Polytechnic State University – San Luis Obispo under the sponsorship of Dr. Peter Schwartz of the Cal Poly Physics department. The aim of this project was to improve upon the design of previously developed Insulated Solar Electric Cookers (ISECs) by adding a thermal storage system to allow for quicker cook times and the ability to cook food at non-peak solar hours. The team’s goal was to develop a working prototype utilizing a phase change medium as the …

Vaccine Cooler For The Global Poor, Benjamin J. Larson, Cooper E. Gibson, Eilbron Younan, Cody R. Volk

Mechanical Engineering

Cal Poly physics professors Peter Schwartz and Nathan Heston approached the Solar Freeze team with the problem that remote communities in Africa have limited access to modern-day medicine or vaccines. They suggested that we try and design a cooling device that can keep vaccines cold for multiple days at a time while the medicine is transported to remote villages. Currently, there are vaccine cooler products on the market, but most of them are very expensive or lack portability. Peter and Nate have tasked the Solar Freeze team to come up with a less expensive solution that is also portable and …

Experimental Investigation Of The Manufacture Of Tunable Graphene Oxide Filter Membranes Using Intense Pulse Light, Joshua H Kotter

Electronic Theses and Dissertations

Reduced graphene oxide is a thin, strong, and inexpensive material with a channel and pore structure that make it a promising candidate for a filtration material. Reduced graphene oxide has been produced and tested in the laboratory, but a lack of scalable manufacturing techniques have limited its commercial use.

This thesis has shown that graphene oxide can be rapidly manufactured with an industrially scalable flash reduction process. The flash reduction process uses 0.58 millisecond pulses from a xenon lamp to reduce the graphene oxide film in less than a minute. Results for partially reduced graphene oxide membranes tuned by the …

Cpu Cooling Pulse Device For Enhanced Heat Transfer, Hannah Farabee, Noémie L. Iñiguez, Hugo Nunez, Wendy Zwanka

Senior Theses

Ice Dragon Cooling is a company which researches thermofluids and heat transfer technologies. The company’s present research focuses on HVAC and computer applications, with an emphasis on nanofluid development. To support Ice Dragon’s mission, the company wants a product that enhances heat transfer efficiency in liquid-cooled CPU systems. The product is to be a pulse device which increases the turbulence of a liquid across a computer CPU cooling block, thereby expediting heat transfer away from the CPU.

The needs for Ice Dragon Cooling were determined based on engineering knowledge and industry consultation. After further analysis, it was determined that increasing …

A Study Of Thermal Energy Storage Of Phase Change Materials: Thermophysical Properties And Numerical Simulations, Kyung-Eun Min

Dissertations and Theses

A Thermal Energy Storage (TES) system is meant for holding thermal energy in the form of hot or cold materials for later utilization. A TES system is an important technological system in providing energy savings as well as efficient and optimum energy use. The main types of a TES system are sensible heat and latent heat. A latent heat storage is a very efficient method for storing or releasing thermal energy due to its high energy storage density at constant temperatures, and a latent heat storage material can store 5-14 times more heat per unit volume than a sensible heat …

Flow Behavior In Radial Rotating Detonation Engines, Scott A. Boller

Theses and Dissertations

Recent progress has been made in demonstrating Radial Rotating Detonation Engine (RRDE) technology for use in a compact Auxiliary Power Unit with a rapid response time. Investigation of RRDEs also suggests an increase in stable operating range, which is hypothesized to be due to the additional degree of freedom in the radial direction which the detonation wave can propagate. This investigation seeks to determine if the detonation wave is in fact changing its radial location. High speed photography was used to capture chemiluminescence of the detonation wave within the channel to examine its radial location, which was found to vary …

Examination Of Flow Dynamics And Passive Cooling In An Ultra Compact Combustor, Tylor C. Rathsack

Theses and Dissertations

The Ultra Compact Combustor (UCC) promises to greatly reduce the size of a gas turbine engine’s combustor by altering the manner in which fuel is burnt. Differing from the common axial flow combustor, the UCC utilizes a rotating flow, coaxial to the engine’s primary axis, in an outboard circumferential cavity as the primary combustion zone. The present study investigates two key UCC facets required to further this combustor design. The first area of investigation is cooling of the Hybrid Guide Vane (HGV). This UCC specific hardware acts as a combustor center body that alters the exit flow angle and acts …

Simulation On Gas-Molten Salt Heat Transfer In Bubble Column For Solar Thermal Storage, Wenhao Pu, Ning Yang, Chen Yue, Dong Han, Weifeng He, Yitung Chen

Mechanical Engineering Faculty Research

The charging and discharging of molten salt thermal storage is of great importance to the operation and maintenance of the solar power plant. The molten salt bubble column is proposed for solar thermal storage, which is regarded as direct contact heat exchanger. The gas from the solar field is directly injected into the molten salt bubble column. High heat transfer rates can be achieved between the gas and the molten salt due to the direct contact. Numeric study on the hydrodynamics and heat transfer characteristic of the gas molten salt bubble column is carried out based on the two fluid …