Power and Energy Commons^™

Passive And Active Battery Balancing Methods Implemented On Second Use Lithium-Ion Batteries, Walter Bartek

Masters Theses

As the number of electric vehicles (EVs) increases, the number of used battery packs that require disposal increases; however, many of these packs still have useful capacity and can be repurposed. When using repurposed large lithium-ion battery packs, deviations between cells within a pack become problematic. These deviations result in a pack that is unbalanced, affecting performance and proving potentially hazardous when charging. Consequently, a battery management system (BMS) is needed. To provide safety, the BMS in this paper monitors and controls the operation of the battery pack. In addition, it controls the redistribution of charge between the cells within …

Cybersecurity Methods For Grid-Connected Power Electronics, Stephen Joe Moquin

Graduate Theses and Dissertations

The present work shows a secure-by-design process, defense-in-depth method, and security techniques for a secure distributed energy resource. The distributed energy resource is a cybersecure, solar inverter and battery energy storage system prototype, collectively called the Cybersecure Power Router. Consideration is given to the use of the Smart Green Power Node for a foundation of the present work. Metrics for controller security are investigated to evaluate firmware security techniques. The prototype's ability to mitigate, respond to, and recover from firmware integrity degradation is examined. The prototype shows many working security techniques within the context of a grid-connected, distributed energy resource. …

Design And Simulation Of Power Electronics Modules, Haonan Jia

Graduate Theses and Dissertations

Silicon carbide (SiC), a wide-bandgap semiconductor material, greatly improves the performance of power semiconductor devices. Its electrical characteristics have a positive impact on the size, efficiency, and weight of the power electronics systems. Parasitic circuit elements and thermal properties are critical to the power electronics module design. This thesis investigates the various aspects of layout design, electrical simulation, thermal simulation, and peripheral design of SiC power electronic modules. ANSYS simulator was used to design and simulate the power electronic modules. The parasitic circuit elements of the power module were obtained from the device parameters given in the datasheet of these …

A Power Constrained 433-Mhz Low Noise Amplifier, Pablo Alvarez Arellano

Graduate Theses and Dissertations

Within wireless communication systems, low noise amplifiers are critical for the performance of receivers. They are primarily responsible for providing enough gain while adding little noise to overcome the noise of the subsequent stages. The LNA presented here is part of a battery-powered transceiver meant to measure crop nutrient data and relay the information. Therefore, power consumption and area become import considerations. To design for a specific power level, a power-constrained noise optimization method is used. The method sizes the amplifying transistor for a fixed source impedance, power dissipation, technology, and operating frequency. The chosen topology is the cascode stage …

A Virtual Space Vectors Based Model Predictive Control For Three-Level Converters, Waleed Saad S. Alhosaini

Graduate Theses and Dissertations

Three-phase three-level (3-L) voltage source converters (VSC), e.g., neutral-point clamped (NPC) converters, T-type converters, etc., have been deemed to be suitable for a wide range of medium- to high-power applications in microgrids (MGs) and bulk power systems. Compared to their two-level (2-L) counterparts, adopting 3-L VSCs in the MG applications not only reduces the voltage stress across the power semiconductor devices, which allows achieving higher voltage levels, but also improves the quality of the converter output waveforms, which further leads to considerably smaller output ac passive filters.

Various control strategies have been proposed and implemented for 3-L VSCs. Among all …

Improving Pv Module Efficiency Through Cooling, Harrison Dawson

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Cascaded Linear Regulator With Negative Voltage Tracking Switching Regulator, Ernest Lei

Master's Theses

DC-DC converters can be separated into two main groups: switching converters and linear regulators. Linear regulators such as Low Dropout Regulators (LDOs) are straightforward to implement and have a very stable output with low voltage ripple. However, the efficiency of an LDO can fluctuate greatly, as the power dissipation is a function of the device’s input and output. On the other hand, a switching regulator uses a switch to regulate energy levels. These types of regulators are more versatile when a larger change of voltage is needed, as efficiency is relatively stable across larger steps of voltages. However, switching regulators …

High- And Low-Voltage Mitigation In Distribution Systems Using Residential Static Volt-Ampere Reactive Compensators, Andrés Valdepeña Delgado

Boise State University Theses and Dissertations

Power distribution systems are experiencing a fast transformation from simple one-way radial feeders to complex systems with multiple sources and bidirectional power flows. The rapid increase of Distributed Generation (DG) connected to the distribution system over the last decade, especially solar photovoltaic (PV), has been the key element to this transformation.

The variable nature of PV-based DG has increased the complexity of voltage regulation in distribution systems. Electric Utilities are facing an increasing number of voltage issues in distribution systems with high penetration of DGs, leading customers to experience voltage levels outside of range A of the ANSI C84.1 standard. …

Improving Pv Module Efficiency Through Cooling, Ashley Cox

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Area Efficient Device Optimization For Esd Protection In High Speed Interface Ics, Dan Thomas Jarard

Graduate Theses and Dissertations

Electrostatic discharge (ESD) protection is considered as a vital step in integrated circuit (IC) manufacturing process. IC chips are unable to overcome the effects of transient events without adequate discharge protection. Recent trend in the industry has seen the incorporation of system level ESD protection within the IC chip. Incorporating system level on-chip ESD protection often increases cost, degrades circuit performance and consumes layout area which could otherwise be used for improving the circuit performance. These design challenges could be easily overcome if the parasitic components in a circuit were used for ESD protection. Despite the various design challenges, on-chip …

Study Of A Symmetrical Llc Dual-Active Bridge Resonant Converter Topology For Battery Storage Systems, John K. George

Graduate Theses and Dissertations

A symmetrical LLC resonant converter topology with a fixed-frequency quasi-triple phase-shift modulation method is proposed for battery-powered electric traction systems with extensions to other battery storage systems. Operation of the converter with these methods yields two unique transfer characteristics and is dependent on the switching frequency. The converter exhibits several desirable features: 1) load-independent buck-boost voltage conversion when operated at the low-impedance resonant frequency, allowing for dc-link voltage regulation, zero-voltage switching across a wide load range, and intrinsic load transient resilience; 2) power flow control when operated outside the low-impedance resonance for integrated battery charging; 3) and simple operational mode …

Investigations Of New Fault-Tolerant Methods For Multilevel Inverters, Haider Mhiesan

Graduate Theses and Dissertations

The demands of power electronics with high power capability have increased in the last decades. These needs have driven the expansion of existing power electronics topologies and developing new power electronics generations. Multilevel inverters (MLI) are one of the most promising power electronics circuits that have been implemented and commercialized in high-voltage direct current (HVDC), motor drives, and battery energy storage systems (BESS). The expanding uses of the MLI have lead to creation of new topologies for different applications. However, one of the disadvantages of using MLIs is their complexity. MLIs consist of a large number of switching devices, which …

A Novel Three-Level Isolated Ac-Dc Pfc Power Converter Topology With Reduced Number Of Switches, Obaid Aldosari

Graduate Theses and Dissertations

The three-level isolated AC-DC power factor corrected (PFC) converter provides safe and more efficient power conversion. In comparison with two-level, three-level PFC converter has the advantages of low total harmonic distortion, low device voltage rating, low di/dt, better output performance, high power factor, and low switching losses at higher switching frequencies. The high frequency transformer (HFT) grants galvanic isolation, steps up or down secondary voltage, and limits damage in case of a fault current.

The existing three-level converter based on solid-state transformer (SST) topologies convert ac power from the electrical grid to a dc load while maintaining at least the …

Low Latency Anomaly Detection With Imperfect Models, Samrat Nath

Graduate Theses and Dissertations

The problem of anomaly detection deals with detecting abrupt changes/anomalies in the distribution of sequentially observed data in a stochastic system. This problem applies to many applications, such as signal processing, intrusion detection, quality control, medical diagnosis, etc. A low latency anomaly detection algorithm, which is based on the framework of quickest change detection (QCD), aims at minimizing the detection delay of anomalies in the sequentially observed data while ensuring satisfactory detection accuracy. Moreover, in many practical applications, complete knowledge of the post-change distribution model might not be available due to the unexpected nature of the change. Hence, the objective …

Machine Learning Modeling Of Horizontal Photovoltaics Using Weather And Location Data, Christil Pasion, Torrey J. Wagner, Clay Koschnick, Steven J. Schuldt, Jada B. Williams, Kevin Hallinan

Faculty Publications

Solar energy is a key renewable energy source; however, its intermittent nature and potential for use in distributed systems make power prediction an important aspect of grid integration. This research analyzed a variety of machine learning techniques to predict power output for horizontal solar panels using 14 months of data collected from 12 northern-hemisphere locations. We performed our data collection and analysis in the absence of irradiation data—an approach not commonly found in prior literature. Using latitude, month, hour, ambient temperature, pressure, humidity, wind speed, and cloud ceiling as independent variables, a distributed random forest regression algorithm modeled the combined …

Syntheses And Properties Of Ta5+ Doped Li7La3Zr2O12, Feng-Feng Peng, Shi-You Li, Tong-Tong Geng, Chun-Lei Li, Shuang-Wei Zeng

Journal of Electrochemistry

The tantalum ion (Ta ⁵⁺) doped garnet-type inorganic solid electrolyte Ta-LLZO was prepared by solid state reaction, and the effect of doping amount on the properties of the materials was investigated. The materials were characterized by X-ray diffraction (XRD), field emission electron scanning microscopy (FESEM) and electrochemical impedance spectroscopy (EIS). And the cycle stability was tested by assembly of LiFePO₄//LLZTO//Li all solid lithium battery. The results show that with the increase of Ta ⁵⁺ doping amount, the material appeared to form a single cubic phase structure. When the Ta ⁵⁺ doping content became 14.09wt.%, x=0.3, the …

Preparation And Characterization Of Cathode Supported Solid Oxide Fuel Cell, Xiao-Nan Bao, Guang-Jun Zhang, Shao-Rong Wang

Journal of Electrochemistry

A site deficient (La_0.8Sr_0.2)_0.95MnO₃ (LSM95) powder was synthesized by solid state reaction as a cathode material. The commercial Zr_0.9Sc_0.1SO_1.95 (SSZ) was selected as an electrolyte material and La_0.8Sr_0.2Cr_0.5Mn_0.5O₃- (LSCrM) was synthesized by sol-gel method as an anode material. Accordingly, single cells of LSCrM-CeO₂|SSZ|3YSZ-LSM95 were prepared by tape casting, sintering and impregnation. The single cell test results for LSCrM-CeO₂|SSZ|3YSZ-LSM95 with 0.11 g·cm ^-2 CeO₂ and using CH₄ as a fuel showed the power …

Research Progress Of Fuel Electrode In Oxide-Ion Conducting Solid Oxide Electrolysers, Ling-Ting Ye, Kui Xie

Journal of Electrochemistry

Solid oxide electrolysers are now attracting much more attentions because they can efficiently produce fuels by electrolyzing H₂O/CO₂. In this paper, a comprehensive introduction to the recent progress in the development of fuel electrode (cathode) materials is provided. The advantages, disadvantages and development trend towards various cathode materials are pointed out. The key scientific and technological problems in this field are emphasized.

Perovskite Catalysts For Fuel Reforming In Sofc:A Review And Perspective, Tong Wei, Jian Li, Li-Chao Jia, Bo Chi, Jian Pu

Journal of Electrochemistry

Solid oxide fuel cell (SOFC) is a generating device by electrochemical reaction to transfer the chemical energy of fossil fuels (coal, oil and gas, etc.), the biomass fuel or other hydrocarbon fuels directly into electricity with higher energy conversion efficiency and lower pollution, which is recognized to be efficient green energy technology in the 21st century. However, when hydrocarbons are directly used as fuel, carbon deposition is easy to occur in nickel-based anode, thus, losing electrochemical catalytic activity. Fuel pre-reforming on the outside of the anode is an effective solution, which strongly relies on highly efficient and stable reforming catalysts. …

Direct Carbon Solid Oxide Fuel Cells, Jiang Liu, Xiao-Min Yan

Journal of Electrochemistry

Carbon is richly reserved in coal, biomasses, and many other nature resources. It is usually used as an energy source through oxygen oxidation reaction. The oxidation is generally realized through combustion which causes serious air pollution. Besides, the conversion efficiency of generating electricity through the combustion process is limited by Carnot efficiency. A direct carbon solid oxide fuel cell (DC-SOFC) is a solid oxide fuel cell (SOFC) directly operated with solid carbon as the fuel. It can convert the chemical energy of carbon into electricity with high efficiency. The concentration of produced CO₂ from a DC-SOFC is so high …