Power and Energy Commons^™

Efficiency Optimization Of Miso Converter, Gabriel Leonides, Christopher S. Peters, Lauren N. Rotsios

Electrical Engineering

In recent years, there has been a rapidly growing need for sustainable energy sources. This need comes from the increasing threat of climate change, significant population growth, as well as the effort to bring electricity to rural and underdeveloped areas across the world. The DC House project at Cal Poly aims to address these issues. The Multiple Input Single Output (MISO) converter is an integral part of the DC House project. The MISO converter is a system that connects multiple power sources to a DC bus. This allows the DC House to be powered by multiple types of renewable energy …

Electric Motorcycle Lithium-Ion Battery System, Amman Fasil Asfaw, Donald J. Alexander

Electrical Engineering

This project entails the processes of design, construction, implementation, and testing of a lithium-ion battery system, including a battery management system, dedicated to converting a 1999 Honda XR100R motorcycle into a fully functional electric motorcycle. The battery system powers the motorcycle with enough voltage and amperage to sustain the needed power capability for a reasonable range. Providing an estimate of the voltage needed, the two largest loads, the DC motor and controller, draw about 48 to 60 volts from the battery for proper operation. Additionally, different aspects of the design also ensure safe operation, correct sizing, and maximum lifetime of …

Analysis And Design Of An Off-Grid Residential Power System, Christopher Rotsios

Master's Theses

This thesis aims to provide a recommended power system design for optimal efficiency, reliability, and cost in off-grid applications. The power system examined in this project is a residence in an off-grid community called Quail Springs that generates its energy from roof mounted solar panels. The existing system was analyzed to see what equipment can remain, what needs to be upsized, and what needs to be added to the system. Two power systems are considered for the residence: a fully AC power system and a hybrid AC/DC power system. Simulations were run in PSCAD to compare the efficiencies of the …

Comparison Of Different Power System Resilience Assessment Methods, Jian How Sam Chan

Student Works (2020-2029)

Climate change has been given significant attention in recent times, calling for more ideas to address issues stemming from extreme weather events. Until climate change can be slowed down and ultimately be reversed, it is an imminent objective to find solutions for the mitigation and prevention of the effects of catastrophic weather events. History has a record of the devastation caused by such events on electrical power infrastructures. While electrical power systems have conventionally been designed and built to weather everyday conditions, confronting cataclysmic high-impact, low-probability events will require more resilient attributes. Power systems are often deemed as the backbone …

Power System Study For Oil And Gas Platform Connected To Onshore Grid, Taharim Rosshidi Hezrimi

Student Works (2020-2029)

Normally for oil and gas offshore platform, the electrical power supply is generated from the generator either using gas turbine generator, gas engine generator and diesel engine generator. The main power supply is backup by diesel engine generator in case emergency or during black start of the platform. As the design of oil and gas platform become complex, the size of generator keeps increasing. A new concept is being explored to mitigate this problem. Oil and gas company is looking to provide power generation from onshore and supplying the electrical power to a substation platform offshore and then distributed it …

Performance Analysis For Single-Stage And Multi-Stage Coreless Axial Flux Permanent Magnet Generator With Different Rotor Structures, Habib Asiful

Student Works (2020-2029)

Axial flux permanent magnet (AFPM) generator is a good candidate for both low and high-speed applications. Compared to radial flux machines, AFPM generators can be easily cascaded for enhanced power/torque while maintaining a fixed machine diameter. To improve power density and reduce cogging torque, some researchers have proposed the removal of iron core in the stator of AFPM machine, giving rise to the concept of coreless AFPM machine. Nevertheless, most of these coreless machines still require back iron on the rotor and/stator to reduce leakage flux. In this project, different rotor structures for single-stage coreless AFPM generators were considered, using …

Meeting Temporary Facility Energy Demand With Climate-Optimized Off-Grid Energy Systems, Jay F. Pearson, Torrey J. Wagner, Justin D. Delorit, Steven J. Schuldt

Faculty Publications

Remote and contingency operations, including military and disaster-relief activities, often require the use of temporary facilities powered by inefficient diesel generators that are expensive to operate and maintain. Site planners can reduce operating costs by increasing shelter insulation and augmenting generators with photovoltaic-battery hybrid energy systems, but they must select the optimal design configuration based on the region’s climate to meet the power demand at the lowest cost. To assist planners, this paper proposes an innovative, climate-optimized, hybrid energy system selection model capable of selecting the facility insulation type, solar array size, and battery backup system to minimize the annual …

Nature-Inspired Electrode Materials For Next Generation Sustainable Energy Storage, Mikhail Miroshnikov

Dissertations, Theses, and Capstone Projects

Despite revolutionizing the world of portable electronics, the contemporary lithium-ion battery (LIB) suffers from challenges associated with the cost, safety, and environmental impact of transition metal oxide-based intercalation cathodes. To alleviate these issues, naturally occurring organic molecules may serve as sustainable alternatives to traditional inorganic cathode materials. The electrochemical properties of organic compounds are derived from redox-active functional groups containing oxygen, nitrogen and sulfur. Additionally, these functional groups are capable of coordinating metal ions beyond lithium, allowing for compatibility with sodium-ion batteries (SIBs) and other earth abundant metal-based energy storage systems. However, despite competitive performance against commercialized cathode materials, much …

Temporal Decomposition For Multi-Interval Optimization In Power Systems, Farnaz Safdarian

LSU Doctoral Dissertations

Large optimization problems are frequently solved for power systems operation and analysis of electricity markets. Many of these problems are multi-interval optimization with intertemporal constraints. The size of optimization problems depends on the size of the system and the length of the considered scheduling horizon. Growing the length of the scheduling horizon increases the computational burden significantly and might make solving the problem in a required time span impossible. Many simplifications and approximation techniques are applied to reduce the computational complexity of multi-interval scheduling problems and make them solvable in a reasonable time span. Geographical decomposition is presented in the …

An Integrated Resource Plan For Arizona Public Service Electric (Aps), Irene Boghdadi, Randy Chiu

Master's Projects and Capstones

Our Masters Capstone Project is an Integrated Resource Plan (IRP) for Arizona’s largest electric utility, Arizona Public Service Electric (APS).

An IRP is developed by utilities to identify the optimal combination of demand- and supply-side resources needed to reliably meet forecasted demand for energy and capacity, including a planning reserve margin, over a future period.

In addition to APS’s obligation to serve the growing load in Arizona while minimizing costs, it is required by the state to adhere to the Renewable Energy Standard (RES) policy of 15 percent retail sales from renewable energy resources by 2025.

The analysis described in …

Assessing The Potential For Greater Solar Development In West Texas, Usa, Dale D. Devitt, M. H. Young, J. P. Pierre

Life Sciences Faculty Research

As population and economies continue to grow on a global scale, so too does the demand for energy. To improve reliability and independence of energy supplies, the U.S. and many other countries are seeking internally-sourced renewable energy; solar is one such renewable-energy source that meets these criteria. However, all energy sources exert some environmental impacts. In the case of solar, direct impacts stem mostly from alteration of land needed to host infrastructure. Understanding the environmental upside and downside potential of solar energy systems allows a more comprehensive, side-by-side comparison with different energy sources. In this article, we focus on the …

Analysis And Investigation Of Hybrid Dc–Dc Non-Isolated And Non-Inverting Nx Interleaved Multilevel Boost Converter (Nx-Imbc) For High Voltage Step-Up Applications: Hardware Implementation, Mahajan Sagar Bhaskar, Dhafer J. Almakhles, Sanjeevikumar Padmanaban, Frede Blaabjerg, Umashankar Subramaniam, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

In significant cases, the generated voltage needs to be step-up with high conversion ratio by using the DC-DC converter as per the requirement of the load. The drawbacks of traditional boost converter are it required high rating semiconductor devices and have high input current ripple, low efficiency, and reverse recovery voltage of the diodes. Recently, the family of Multilevel Boost Converter suggested and suitable configuration to overcome the above drawbacks. In this article, hybrid DC-DC non-isolated and non-inverting Nx Interleaved Multilevel Boost Converter (Nx-IMBC) is analyzed in Continuous Conduction Mode (CCM) and Discontinuous Conduction Mode (DCM) with boundary condition and …

Multiple Input Single Output Converter With Uneven Load Sharing Control For Improved System Efficiency, Kristen Y. Chan

Master's Theses

This paper presents the development and study of multiple-input single-output converter (MISO) for the DC House project that utilizes a controller to maximize the overall converter’s efficiency. The premise of this thesis is to create uneven load current sharing between the converters at different loading conditions in order to maximize the efficiency of the overall MISO converter. The goal is to find a proper ratio of current from each converter to the total load current of the MISO system to achieve the greatest efficiency. The Arduino microcontroller is implemented to achieve this goal. The design and operation of the MISO …

A Novel Arc Welding Power Supply With Improved Power Factor Correction, Benjamin H. Tan

Master's Theses

This paper presents the design and development of a novel Arc Welding Power Supply utilizing a modified two-switch forward converter topology. The proposed design improves the power quality by improving power factor to near unity and reducing total harmonic distortion. State space analysis of the proposed circuit showed that the circuit followed a boost-buck input output relationship. Simulation of the circuit was first implemented in LTspice to verify the functionality of the new topology. Hardware implementation of the proposed design was built on a scaled-down prototype for a proof-of-concept of the new topology. The prototype specifications were created for a …

Multiple Input Single Output Converter With Maximum Power Point Tracking For Renewable Energy Applications, Kenneth K. Nguyen, Taufik Taufik

Master's Theses

In this thesis, a maximum power point tracking (MPPT) for multiple input single output (MISO) converter is presented such that power generated from multiple individual energy sources can be combined to deliver the maximum amount of power to a common resistive load. Typically, MISO converters will employ techniques that yield equal current sharing from each energy source. However, this may not be desirable since each source may be rated at different power ratings and/or may experience different operating conditions, preventing the system MISO converter to acquire the most available total power from the sources. Utilizing MPPT control would therefore be …

Cascaded Linear Regulator With Positive Voltage Tracking Switching Regulator, Brandon K. Nghe

Master's Theses

This thesis presents the design, simulation, and hardware implementation of a proposed method for improving efficiency of voltage regulator. Typically, voltage regulator used for noise-sensitive and low-power applications involves the use of a linear regulator due to its high power-supply rejection ratio properties. However, the efficiency of a linear regulator depends heavily on the difference between its input voltage and output voltage. A larger voltage difference across the linear regulator results in higher losses. Therefore, reducing the voltage difference is the key in increasing regulator’s efficiency. In this thesis, a pre switching regulator stage with positive voltage tracking cascaded to …

The Design And Analysis Of Large Solar Pv Farm Configurations With Dc Connected Battery Systems, Oluwaseun M. Akeyo, Vandana Rallabandi, Nicholas Jewell, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Typically, solar inverters curtail or “clip” the available power from the PV system when it exceeds the maximum ac capacity. This paper discusses a battery system connected to the dc-link of an inverter to recuperate this PV energy. Contrary to conventional approaches, which employ two dc-dc converters, one each for the battery and solar PV system, the proposed configuration utilizes a single dc-dc converter capable of simultaneously operating as a charge controller and a maximum power point tracking (MPPT) tracking device. In addition to improving the overall system capacity factor, increasing the conversion efficiencies and ensuring MPPT stability, the proposed …

Improving Pv Module Efficiency Through Cooling, Blake Bradley

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

Improving Pv Module Efficiency Through Cooling, Megan Reynolds

Chemical Engineering Undergraduate Honors Theses

The Solarbacks researched and designed a variety of cooling methods that could be used to improve the efficiency of photovoltaics. These cooling methods can be separated into two categories: active and passive methods. The active cooling method of hydraulic cooling and the passive cooling methods of heat sinks (fins), optical coatings, thermosyphons, phase change materials, and thermoelectric generators were all taken into consideration as potential cooling methods. Passive cooling methods were preferred because the use of electricity required for the cooling mechanism would reduce the net electricity and subsequent profit from the panels.

Two variations of hydraulic cooling were researched: …

An Investigation Of Diode Failure, Nicholas James Adams

Physics

Solar electricity can be used to cheaply cook food and charge electronic devices. We investigate the viability of using diodes as heating elements for insulated solar electric cooking (ISEC). In addition, information on designing and constructing ISEC compatible phone chargers and rechargeable LED lighting systems is included.