Power and Energy Commons^™

Energy Efficient Led Displays, John Mani Kumar Jupalli

UNLV Theses, Dissertations, Professional Papers, and Capstones

In this research work, an innovative pixel architecture RGBW, consisting of red (R), green (G), blue (B), and white (W) LEDs, is designed and implemented for color generation. Energy consumption of new pixel architecture consisting of RGBW LEDs is compared to standard architecture consisting of RGB LEDs. Human perception experiments are conducted to study the differences in perception between the two architectures when the same colors are generated using RGBW vs. RGB. Measurements of power for a 32inch x 16inch LED display has proved up to 18% power savings for low saturated colors, up to 8% for high saturated colors …

Photoelectrochemical Properties Of N, S, And Cl Modified Nano Tio2 Thin Films, Hong Yun, Chang-Jian Lin, Jing Li, Rong-Gui Du

Journal of Electrochemistry

The nitrogen(N),sulfur(S) and chlorine(Cl) modified nano TiO₂ thin films were prepared by adding Ti(O-n-Bu)₄ as the precursor into concentrated HNO₃,H₂SO₄ and HCl Solutions,respectively,on different substrates in a sol-gel process.The photoelectrochemical performances of N,S and Cl modified nano TiO₂ thin films have been studied by UV-vis(DRS),photocurrent curves,EIS and OCP-time curves.N-modified TiO₂ nano films show better surface structure,which helps to improve the quantum efficiency of nano TiO₂ thin films.

Hydrothermal Reduction Synthesis Of Lifepo4 And Its Electrochemical Performance, Hong-Li Zou, Guang-Hui Zhang, Pei-Kang Shen

Journal of Electrochemistry

The cathode materials of LiFePO₄ were prepared via a hydrothermal reduction method using FeCl₃ as Fe source and iron as a reducing agent.The results showed that ferric salt could be reduced to ferrous salt completely under the hydrothermal condition and pure-phase LiFePO₄ was obtained based on the test results of XRD and FTIR.Carbon-coated LiFePO₄ was synthesized by pyrolysisng glucose at high temperature.The morphologies of pure LiFePO₄ displayed cluster-like while the LiFePO₄/C displayed sphere-like particles.The electrochemical test showed that the LiFePO₄/C had good rate performance,while LiFePO₄ delivered much lower discharge capacity.

Electrodeposition Of Lead Dioxide From Dluoroborate Solutions, Chun-Mei Kong, Yong-Ming Tang, Wen-Zhong Yang, Xiao-Yuan Yang

Journal of Electrochemistry

The PbO₂ anodes were prepared on platinum from fluoroborate media and its doped solutions by electrodeposition technique.Elecchemical and pysicochemical properties of these PbO₂ films were studied by cyclic voltammetry methods,XRD and SEM.The results showed that the presence of BF₄-increased PbO₂ electrodeposition rate;the prepared lead dioxide consisted of β-PbO₂;the preferential orientation of crystals and surface morphology were affected a lot by doping F-and Fe³⁺.The FB/F-Fe-PbO₂ electrode exhibited regular-shaped layers with compact morphology.Furthermore,increasing current density also change the preferential orientation of PbO₂ crystals.

The Sol-Gel Synthesis And Electrochemical Performance Of Li3V2(Po4)3/C Cathode Material For Lithium Ion Battery, Li-Ying Liu, Lian Chen, Hai-Yan Zhang, Yu-Chun Zhai

Journal of Electrochemistry

Li₃V₂(PO₄)₃/C was synthesized by sol-gel method with citric acid as chelate and C sources. Physical and electrochemical performances of as-prepared materials were characterized through XRD, SEM and galvanostatic charge-discharge tests,etc. The results showed that products produced by calcining at 800 ℃ for 12 h had a single phase crystal structure and relatively small particle sizes with uniform distribution. At 0.1 C, 0.5 C and 1 C, the initial specific discharge capacities were 153.0, 143.1 and 130.6 mAh·g^-1, respectively, and capacity efficiencies were 93.1%, 85.4% and 77.3% after 50 cycles, respectively. …

Research On Nafion/Sio2 Composite Membrane In All Vanadium Redox Flow Battery, Dong-Dong Liu, Mao-Cai Lin, Tao Guan, Qing-Chun Yu

Journal of Electrochemistry

The Nafion117/SiO₂ composite membrane was prepared by sol-gel method.The results showed that,during composite membrane preparation process,the ratio of MeOH and TEOS did not affect the penetration rate of VO²⁺ basically,however,the lowest permeability of 427×10-9cm²/s in the membrane was achieved while hydrolysis time was 10 min and natural drying for 24 h after hydrolysis,which reduced by 52 times than that in Nafion117 membrane.The SEM tests proved that SiO₂ grains grew bigger in the composite membrane during the natural drying,and most of the holes in Nafion117 were filled.Single cell test showed the battery power efficiency was improved …

Effects Of Solvents And Electrolyte Salts On The Electrochemical Reduction Of Oxygen In Non-Aqueous Electrolytes, Yan-Yan Tian, Wei Wu, Jun Gao, Yong Yang

Journal of Electrochemistry

The electrochemical reduction processes of oxygen in different non-aqueous solvents such as acetonitrile(MeCN),propylene carbonate(PC) and their mixtures were investigated by cyclic voltammetry method.The results indicated a one electron reduction of oxygen to O^2-occured in these systems as a first step reduction,no matter whether in tetrabutylammonium hexafluorophosphate(TBAPF₆)/MeCN or TBAPF₆/PC electrolyte.However,the CV curves in 0.1 mol·L^-1 TBAPF₆/MeCN showed a couple of reversible redox peaks,indicating that the reduction process of oxygen was irreversible in the 0.1 mol·L^-1 TBAPF₆/PC electrolyte.In the PC-based electrolyte,the reduction current peak reduced largely and the oxidation peak …

Energy Storage And Management For A Small Series Plug-In Hybrid Electric Vehicle, Liqin Ni

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Plug-in hybrid electric vehicles (PHEVs) are gaining increasing interest for both residential and commercial transportation applications. In PHEV design, energy storage system (EES) is a critical component which will impact the overall design efficiency, performance, cost and etc. This dissertation aims to design an advanced energy storage system for a small plug-in hybrid electric vehicle, whose performance will approach very closely to the optimal possible, in terms of energy efficiency and acceleration, for passenger road vehicles application. Moreover, practical automotive requirements are considered during ESS design, such as cost, life time, safety and volume.

This dissertation utilizes ultracapacitors in conjunction …

Designing A Photovoltaic System Hybrid For A Health Clinic In Camilo Ortega, Nicaragua, Jeremy Holliman

Electrical Engineering

As developing nations continue to foster the development of their technologies and economies, industrialized nations have taken an active approach in providing green and sustainable alternatives for them to consider. Non-profit organizations like Engineers Without Borders holds sustainable international development as paramount to all international projects that their student and professional chapters undertake. The Cal Poly Engineers Without Borders student chapter has implemented a variety of projects from slow sand filters to compressed earth blocks, and the Nicaragua team is in the process of designing a health clinic for the Camilo Ortega community. In order to power the health clinic, …

Economic Analysis Of A Brackish Water Photovoltaic-Operated (Bwro-Pv) Desalination System, Ali Al-Karaghouli, Lawrence L. Kazmerski

Publications (E)

The photovoltaic (PV)-powered reverse-osmosis (RO) desalination system is considered one of the most promising technologies in producing fresh water from both brackish and sea water, especially for small systems located in remote areas. We analyze the economic viability of a small PV-operated RO system with a capacity of 5 m³/day used to desalinate brackish water of 4000 ppm total dissolve solids, which is proposed to be installed in a remote area of the Babylon governorate in the middle of Iraq; this area possesses excellent insolation throughout the year. Our analysis predicts very good economic and environmental benefits of …

Economic Optimization Of Offshore Wind Farms Using The Geometric Algorithm, Mahidhar Nandigam

Electrical & Computer Engineering Theses & Dissertations

The research project related to this thesis focuses on the optimization of electrical systems for offshore wind farms for a given capacity. The optimal design and planning is a critical issue for developing cost effectively Offshore Wind Farms in energy systems. The Geometric Optimization Algorithms approach has been adopted to develop an optimization program, where the main components of the electrical system of an offshore wind farm and key technical specifications are used as parameters to be optimized for a minimum cost with necessary constraints. The effectiveness of the optimization program can be evaluated with real-time comparison between offshore wind …

The Application Of Multi Frequency Resonant Controllers In In A Dfig To Improve Performance By Reducing Unwanted Power And Torque Pulsations And Reducing Current Harmonics., Joseph Kearney, Michael Conlon, Eugene Coyle

Conference papers

The paper describes a method to control the rotor-side and grid side converters in a DFIG when subjected to the effects of network voltage unbalance conditions. Multi Frequency Resonant Controllers are incorporated into the grid side and rotor side converters to assist in the control functions. The Resonant Controllers are tuned to twice the network frequency to assist in the control of power and torque pulsations and to three times the network frequency to assist in the control of the generated third harmonic currents. A DFIG model is implemented in Matlab/Simulink and simulations show the reduction in power and torque …

The Application Of Multi Frequency Resonant Controllers In In A Dfig To Improve Performance By Reducing Unwanted Power And Torque Pulsations And Reducing Current Harmonics., Joseph Kearney, Michael Conlon, Eugene Coyle

Conference papers

The paper describes a method to control the rotor-side and grid side converters in a DFIG when subjected to the effects of network voltage unbalance conditions. Multi Frequency Resonant Controllers are incorporated into the grid side and rotor side converters to assist in the control functions. The Resonant Controllers are tuned to twice the network frequency to assist in the control of power and torque pulsations and to three times the network frequency to assist in the control of the generated third harmonic currents. A DFIG model is implemented in Matlab/Simulink and simulations show the reduction in power and torque …

User's Guide To Mbc3: Multi-Blade Coordinate Transformation Code For 3-Bladed Wind Turbine, G. S. Bir

Publications (E)

The dynamics of wind turbine rotor blades are conventionally expressed in rotating frames attached to the individual blades. The tower-nacelle subsystem though, sees the combined effect of all rotor blades, not the individual blades. Also, the rotor responds as a whole to excitations such as aerodynamic gusts, control inputs, and tower-nacelle motion—all of which occur in a nonrotating frame. Multi-blade coordinate transformation (MBC) helps integrate the dynamics of individual blades and express them in a fixed (nonrotating) frame. MBC involves two steps: transforming the rotating degrees of freedom and transforming the equations of motion. Reference 1 details the MBC operation. …

Green Power Marketing In The United States: A Status Report (2009 Data), Lori Bird, Jenny Sumner

Publications (E)

This report documents green power marketing activities and trends in the United States. Aggregate green power sales data for all voluntary purchase markets across the United States are presented for 2009. The data presented in this report are based primarily on figures provided to NREL by utilities and independent renewable energy marketers. Because data cannot be obtained from all market participants, the estimates presented here likely represent an underestimate of the market size. Key trends identified in this year’s report include:
• In 2009, total retail sales of renewable energy in voluntary markets exceeded 30 million MWh, an increase of …

Wavelet Based Islanding Detection Of Dc-Ac Inverter Interfaced Dg Systems, Mohamed Moin Hanif, Malabika Basu, Kevin Gaughan

Conference papers

The increased penetration of distributed generation (DG) often connected to grid through dc-ac interface has made islanding detection an important and challenging issue to power engineers. Several methods based on passive and active detection scheme have been proposed in the literature. While passive schemes have a large non detection zone (NDZ), concern has been raised on active method due to its degrading power quality effect. This paper proposes a wavelet based passive islanding detection scheme with almost zero NDZ for dc-ac inverter interfaced grid connected DGs. The key idea is to utilize the spectral changes in the higher frequency components …

An In Situ Fourier Transform Infrared Spectroelectrochemical Study On Alcohols Electrocatalytic Oxidation At Pd Electrode In Acidic Solution, Hai-Ping Huang, Lian-Qin Wang, Pei-Kang Shen

Journal of Electrochemistry

The methanol and ethylene glycol electrooxidation on palladium electrode in acidic solution has been investigated by cyclic voltammetry and in situ Fourier transform infrared spectroelectrochemistry. It shows that the oxidation of methanol and ethylene glycol at Pd electrode cannot proceed until over 1.5 V in acidic and neutral media. The overpotential decreases and the peak current density increases with the reduction in pH values. The formation of the oxygen-containing species significantly affects the alcohol oxidation on Pd electrode. The in situ FTIR spectroscopic measurements show that the oxidation products of ethylene glycol on Pd electrode are CO₂ and oxalic …

Electrooxidation Of Carbon Monoxide On Pd Thin Film-Coated Au Electrodes: Film Thickness Dependence, Yuqing Yang, Shouzhong Zou

Journal of Electrochemistry

The adsorption and electrooxidation of CO on Pd-coated Au electrodes were studied by cyclic voltammetry and surface-enhanced Raman spectroscopy (SERS) . It is found that CO oxidation activity is film thickness dependent. Cyclic voltammograms (CVs) showed that CO oxidation peak potential shifted positively with the increase of the Pd thickness. SERS showed a redshift of the C—O stretching frequency with increasing Pd film thickness. These observations were explained by the dband theory. The strain effect strengthens CO adsorption and stabilizes adsorbed CO,while the ligand effect weakens CO adsorption and eases its oxidation. The ligand effect overpowers the strain effect.

Solid State Nmr Studies Of Lithium Manganese Silicate As Positive Electrode Materials For Li-Ion Batteries, Hu Cheng, Zi-Geng Liu, Yi-Xiao Li, Zhong Chen, Yong Yang

Journal of Electrochemistry

The Li₂MnSiO₄ cathode material for lithium ion batteries was synthesized by sol-gel assisted hydrothermal method. XRD,FTIR and SS-NMR were used to study the phase,structure and morphology of obtained samples. Electrochemical performance of cathode material was tested. The results show that the main phase of sample prepared was Li₂MnSiO₄,whereas a small amount of impurities (Li₂CO₃) were existed. The Li₂MnSiO₄ cathode material gave an initial discharging capacity of about 190 mAh·g ^-1. But this capacity faded rapidly during the cycling process due to the decomposition of Li …

Comparative Study Of Nanoporous Pt, Ptru And Ptruir Catalysts Using Electrochemical Ftir Spectroscopy, M. Amussen Robert, Holt-Hindle Peter, Nigro Samantha, Aicheng Chen

Journal of Electrochemistry

In recent years much effort has been put towards developing efficient Pt-based electrocatalysts for applications in fuel cells. With the rising cost of precious metals such as Pt,the need to enhance the activity and to decrease the load of catalysts is prominent. Herein we report on the synthesis and comparative study of nanoporous Pt,PtRu and PtRuIr electrocatalysts. The nanoporous electrodes were fabricated using a hydrothermal method and characterized by scanning electron microscopy (SEM) ,energy dispersive spectroscopy (EDS) ,X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) . The electrocatalytic activity of the fabricated nanopo- rous materials was evaluated using both CO …