Polymer Science Commons^™

Review Of Challenges And Advances In Modification Of Food Package Headspace Gases, Ziynet Boz, Bruce A. Welt, Jeffrey K. Brecht, William Pelletier, Eric Mclamore, Gregory A. Kiker, Jason E. Butler

Journal of Applied Packaging Research

Modified Atmosphere Packaging (MAP) has been widely used as an effective way to preserve foods. Fresh produce, meat and meat products, seafood, and dairy products can benefit from modified gaseous atmospheres, which are usually achieved by reducing oxygen and increasing carbon dioxide concentrations, within limits, defined by product tolerances. MAP of fresh produce is particularly challenging because products are living and respiring. Respiration rates depend on several factors including temperature, oxygen, and carbon dioxide concentrations. Balancing package permeation with respiration is challenging, often due to limited selection of practical packaging materials. Failing to remain within tolerance limits of products leads …

Waste Management By Waste: Removal Of Acid Dyes From Wastewaters Of Textile Coloration Using Fish Scales, S M Fijul Kabir

LSU Master's Theses

Removal of hazardous acid dyes by economical process using low-cost bio-sorbents from wool industry wastewaters is of a pressing need, since it causes skin and respiratory diseases and disrupts other environmental components. Fish scales (FS), a by-product of fish industry, a type of solid waste, are usually discarded carelessly resulting in pungent odor and environmental burden. In this research, the FS of black drum (Pogonias cromis) were used for the removal of acid dyes (acid red 1 (AR1), acid blue 45 (AB45) and acid yellow 127 (AY126)) from wool industry wastewaters by absorption process with a view to …

Definite Indefiniteness Of "Molecular Weight" As A Claim Term For Polymer-Related Patents, Ping-Hsun Chen

The Journal of Business, Entrepreneurship & the Law

The molecular weight of a polymer is not just a number for a single molecule. In fact, molecular weight measurement is based on a large volume of molecules of the same polymer. Due to the non-uniformity of molecular weights, there are several methods to measure an “average molecular weight” of a polymer. Unfortunately, the Federal Circuit in Teva Pharms. USA, Inc. v. Sandoz, Inc., 789 F.3d 1335 (Fed. Cir. 2015), held that the term “molecular weight” in several polymer claims was indefinite, because the term could mean either peak average molecular weight, number average molecular weight, or weight average molecular …

Comparison Of Eosin And Fluorescein Conjugates For The Photoinitiation Of Cell-Compatible Polymer Coatings, Jacob L. Lilly, Anuhya Gottipati, Calvin F. Cahall, Mohamed Agoub, Brad J. Berron

Chemical and Materials Engineering Faculty Publications

Targeted photopolymerization is the basis for multiple diagnostic and cell encapsulation technologies. While eosin is used in conjunction with tertiary amines as a water-soluble photoinitiation system, eosin is not widely sold as a conjugate with antibodies and other targeting biomolecules. Here we evaluate the utility of fluorescein-labeled bioconjugates to photopolymerize targeted coatings on live cells. We show that although fluorescein conjugates absorb approximately 50% less light energy than eosin in matched photopolymerization experiments using a 530 nm LED lamp, appreciable polymer thicknesses can still be formed in cell compatible environments with fluorescein photosensitization. At low photoinitiator density, eosin allows more …

Hydrophobic Surface Modification Of Polymethyl Methacrylate By Two-Dimensional Plasma Jet Array At Atmospheric Pressure, Feng Liu, Meiling Cai, Bo Zhang, Zhi Fang, Chunqi Jiang, Kostya Ken Ostrikov

Bioelectrics Publications

Recently developed atmospheric pressure plasma jet (APPJ) is considered as a novel and efficient technique for uneven surfaces processing and APPJ array effectively expands the treatment area of a single APPJ. In this paper, a two-dimensional (2D) APPJ array in Ar/tetramethylsilane (TMS) is used to improve the surface hydrophobicity of polymethyl methacrylate (PMMA) by depositing polymerized silicalike clusters on the jet-PMMA interface. The electrical and optical characteristics of the 2D Ar/TMS APPJ array are measured to optimize experimental conditions. The wettability of jet-PMMA interface is assessed by measuring water contact angle, which increases from 65° to a maximum value of …

Sequence Effects On The Glass Transition Temperature, William Drayer

Williams Honors College, Honors Research Projects

Lithium ion batteries are widely used for the energy needs of portable electronic devices. Unfortunately, current liquid organic solvents used as the electrolytic portion of the battery have low thermal stability, resulting in batteries that may combust upon failure. This flammability can be attributed to the configurational strain in cyclic organic electrolytes. Due to the lack of configurational strain in a flexible polymer chain, designing polymer electrolytes for use in lithium ion batteries may result in a safer battery due to their lower flammability in comparison to traditional liquid organic electrolytes. From the perspective of an electrolytic polymer, lowering the …

The Combined Material Flow Analysis And Life Cycle Assessment For Integrated End-Of-Life Of Mercury Contaminated Petroleum Waste Management, Putthita Chongchongprasert

Chulalongkorn University Theses and Dissertations (Chula ETD)

Now a day, the waste management generated by offshore petroleum operation (including drilling and production) located in the Gulf of Thailand seem to be a great challenge. Because of their unique characteristic in terms of hazardous properties, petroleum waste requires particular treatments to reduce potential impacts to the environment and human life. This study, the petroleum waste by their disposal code, and waste code was sorted. The Hg-contaminated petroleum waste flow starting from waste generation towards to final disposal was conducted by Material Flow Analysis (STAN, 2.6.601) and Life Cycle Assessment (SimaPro 8.3.0.0) was conducted as tools for evaluating the …

Electrospinning Aqueous Solutions Of Poly(Ethylene Oxide) Using A Corona-Type Apparatus, Nicholas Neill

Williams Honors College, Honors Research Projects

The purpose of this project was to evaluate working parameters for the corona spinneret to create electrospun fibers/ fiber mat. This project was set-up using a Box-Behnken design of experiment. The working parameters were investigated by performing the electrospinning process, altering the working conditions, collecting the electrospun fibers. The scope of this project includes three primary operational conditions: distance between the spinneret and the collection plate, the viscosity (weight percent) of PEO in the spinning solution and the weight percent of NaCl in the spinning solution. The distance between the spinneret and the collection plate were varied to 18 cm, …

Effects Of Hofmeister Ions On Gelation Of Gelatin And Pluronic Hydrogels, Eric Britton

Williams Honors College, Honors Research Projects

The purpose of the project was to observe the effects of the Hofmeister series of ions on the gelation of gelatin and Pluronic-127 hydrogels. Hydrogels are semi-solid materials that contain a network of joined molecules through intermolecular interactions which are capable of holding water. Gelatin and Pluronic-127 (PF-127) are thermoreversible, physical crosslinked gels. Gelation occurs when temperature, or other driving forces, reduce the polymer chain solubility until a distinct 2-phase system forms. When aqueous ions are present in solution, they exhibit specific ion effects that have either a stabilizing or destabilizing effect on the solubility of proteins and other polymers. …

Tandem Mass Spectrometry (Ms/Ms) For Determination Of Architecture Of Synthetic Polymers, Shoumik Saha

Williams Honors College, Honors Research Projects

Tandem Mass Spectrometry (MS/MS) was used to determine the architecture of synthetic polymers and they are difluorene-N₃, 3-difluorene-N₃ and VPOSS-3-difluorene. VPOSS materials usually exhibit electrochemical properties and the research was performed to determine their accurate structure and to provide evidence of their proper synthesis. The compounds were mixed with a matrix solution, DCTB, and a silver salt to enable proper protonation. The solvent mixture was on a MALDI plate and then put into the mass spectrometer. The mass spectrum generated was analyzed and each fragment was identified to structures with the synthetic polymers via ChemDraw. Thus, trial …

Correlation Of Electrospun Polyvinylpyrrolidone Fiber Mat Thickness With Basis Weight, Fiber Diameter, Pore Size Distribution, And Air Permeability, Leah Mcpherson

Williams Honors College, Honors Research Projects

This project developed correlations between electrospun polyvinylpyrrolidone fiber mat thickness, basis weight, fiber diameter, pore size, and air permeability. The hypotheses were thinner fibers produce thicker mats, pore size decreases with fiber diameter, pore size and permeability decrease as basis weight increases. Project results could be used for modeling or quality control purposes.

Fiber diameter distributions were analyzed using a Scanning Electron Microscope and FibraQuant 1.3 software. Four conditions were chosen for further study: 0.284 ± 0.104 µm, 0.379 ± 0.128 µm, 0.520 ± 0.138 µm, and 0.733 ± 0.177 µm. Lower PVP concentrations produced thinner fibers.

Sample thickness (nm) …

Modeling The Effect Thickener Structure Has On The Oil Release Of Grease, Dana Cressman

Williams Honors College, Honors Research Projects

Our hypothesis was that the thickener type and micelle concentration of grease affected its viscoelastic properties. Measurements were made using a TA AR G2 rheometer and calculations were made using TA rheometer analysis software to characterize the viscoelastic response of grease under oscillatory shear and frequency tests. The oscillatory frequency tests determined the critical micelle concentration. The oscillatory stress tests were taken at temperatures from 5 to 65 degrees Celsius to create a master curve based on time temperature superposition of the measurements. The crossover points of G’ and G” on the oscillatory stress tests demonstrated where the grease transitions …

Green-House Gas Storage Through Enhanced Hydrate Formation, Thiphakorn Absuwan

Chulalongkorn University Theses and Dissertations (Chula ETD)

The CO₂ hydrate formation in the presence of different tetrahydrofuran (THF), sodium dodecyl sulfate (SDS), and methyl ester sulfonate (MES) concentrations was investigated in terms of kinetics and thermodynamics. The formation experiment was conducted in the quiescent condition and close system at 3 MPa and 3 °C. The results showed that the CO₂ hydrates formed in the presence of 10 mol% THF, while it did not form with 5.56 mol% THF. The presence of SDS or MES did not promote the hydrate formation. However, the hydrates formed in the presence of a mixture of SDS or MES with 5.56 mol% …

Optimization Algorithm Study : Mixed Integer Linear Programming, Tittawat Fongchantuk

Chulalongkorn University Theses and Dissertations (Chula ETD)

In the present, many petrochemical and petroleum products (engine fuel, solvent, plastic and synthetic rubber. etc.) are important. They are transported by ship, pipe line or train every day. So, minimizing transportation cost and time or maximizing profit is an important key of every company. In this optimization process, the optimal supply chain must be well developed in mathematical programming with the objective function of minimum cost or maximum profit and be solved by using optimization solvers. Objective functions and their constraints are solved by suitable types of optimization solvers: Linear programming (LP) and mixed integer linear programming (MILP). MILP …

The Role Of Microenvironment Reagent Solubility On Reaction Kinetics Of 4-Nitrophenol Reduction, Michael P. Zeevi, Andrew Harrison, Christina Tang

Undergraduate Research Posters

The Role of Microenvironment Reagent Solubility on Reaction Kinetics of 4-Nitrophenol Reduction

Michael Zeevi¹ with Andrew Harrison¹ and Christina Tang, PhD¹

¹Department of Chemical and Life Science Engineering, VCU School of Engineering

Introduction: Nanoparticles are of increasing interest due to their high surface area to volume ratio, as well as that they enable fine-tuning of the reaction microenvironment. Through flash nanoprecipitation, core-shell polymer nanoreactors were formed by directed self-assembly. Using the reduction of 4-nitrophenol as a model reduction reaction, we investigated the effect of reagent solubility in the nanoreactor microenvironment’s on nanoreactor kinetics.

Methods: The standard …

Surface Engineering And Monomer Design For Light-Mediated Ring Opening Metathesis Polymerization, Ishan A. Fursule

Theses and Dissertations--Chemical and Materials Engineering

Stimuli-responsive materials are changing the landscape of actuated materials, optoelectronics, molecular machines, solar cells, temporary memory storage, and biomedical materials. Specifically, photo-responsive polymers have gained acceleration in research and application since the last two decades in the form of a surface coating and micro-patterns. Light as a stimulus can be coherent, mono or polychromatic, tunable for power (intensity) and energy (wavelength), and has precise spatiotemporal control. Conventional surface coating techniques such as spin coating are unable to impart properties to the coatings in terms of sturdiness, homogeneity, uniformity over the complex surface, post deposition modification, and process efficiency. Also, in …

Design And Analysis Of Curcumin Conjugated Poly(Beta-Amino Ester) Networks For Controlled Release In Oxidative Stress Environments, Carolyn T. Jordan

Theses and Dissertations--Chemical and Materials Engineering

Oxidative stress, the imbalance of free radical generation with antioxidant defenses, leads to cellular inflammation, apoptosis and cell death. This compromised environment results in debilitating diseases, such as oral mucositis (OM), atherosclerosis, and ischemia/reperfusion injury. Antioxidant therapeutics has been a proposed strategy to ameliorate these imbalances and maintain homeostatic environments. However, the success of these approaches, specifically curcumin, has been limited due to characteristics such as hydrophobicity and high reactivity when released as bolus doses to contest to oxidative stress induced diseases. The development of a controlled release system to aid in protection of the antioxidant capacity of curcumin, as …

Surface Functionalization Via Photoinitiated Radical Polymerization For Rare Cell Isolation And Mechanical Protection, Calvin Frank Cahall

Theses and Dissertations--Chemical and Materials Engineering

Surface functionalization of living cells for cell therapeutics has gained substantial momentum in the last two decades. From encapsulating islets of Langerhans, to cell laden gels for tissue scaffolds, to individual cell encapsulation in thin hydrogels, to surface adhesives and inert surface camouflage, modification of living cell surfaces has a wide array of important applications. Here we use hydrogel encapsulation of individual cells as a mode of protection from mechanical forces for high throughput cell printing, and chemical stimuli for the isolation of rare cells in blood.

In the first study, we review methods of surface functionalization and establish a …

Green Composites Of Polylactic Acid Filled With Natural Fiber For Biodegradation Application, Chamaiporn Yamoum

Chulalongkorn University Theses and Dissertations (Chula ETD)

This research focuses on how to use natural fibers available from agricultural residues to produce biodegradable materials such as mulch films. Green composites were prepared from natural fibers (peanut shell and bagasse fiber) and polylactic acid (PLA) together with plasticizers. The presence of plasticizers improved PLA molecular mobility as seen by the reduction of glass transition, cold crystallization, and melting temperatures. The addition of natural fibers into PLA brought down decomposition temperature when compared to PLA. The morphological study of the composites showed poor interfacial adhesion between natural fibers and PLA matrix. Moreover, the loading of plasticizers improved distribution of …

Production Of Biojet Fuel From Palm Fatty Acid Distillate Over Ni/Hzsm-12 Catalyst, Chayanee Hiranyasiri

Chulalongkorn University Theses and Dissertations (Chula ETD)

Generally, jet fuels are mainly derived from the refining of petroleum feedstock which exhaust greenhouse gases. Therefore, biojet fuel is introduced as an alternative way to solve the problem. Moreover, jet fuel must have a freezing point about -47 °C or below so iso-paraffins which have low freezing point are required. In this study, the hydroprocessing of palm fatty acid distillate (PFAD) over synthesized Ni/HZSM-12 and conventional Ni/HY catalysts which have different morphology and pore size for producing biojet fuel (hydrocarbon in a range of C9-C14) was studied in a continuous flow fixed-bed reactor under conditions of 350-400 °C, 10-30 …