The Effect Of Fabric Architecture On The Processing And Properties Of Composites Made By Vacuum Assisted Resin Transfer Molding,
2019
University of Dayton
The Effect Of Fabric Architecture On The Processing And Properties Of Composites Made By Vacuum Assisted Resin Transfer Molding, Francois Ntakobatagize, Oscar Ntakontagize, Donald A. Klosterman
Chemical and Materials Engineering Faculty Publications
The goal of this research project was to evaluate and compare the effect of fabric architecture on the processing and properties of composites made by Vacuum Assisted Resin Transfer Molding (VARTM). The fabric architectures investigated included plain weave, satin weave, and warp-knit unidirectional. The fiber types included E-glass and standard modulus carbon fiber. Flat panels were fabricated with a lab scale VARTM process using an epoxy resin system. Fabric plies were cut to 45 cm x 30 cm (18 in. x 12 in.), and the number of plies used depended on the fiber areal weight of each fabric to produce …
Modeling Of Vapor Sorption In Nanoparticle Chemiresistors,
2019
University of Connecticut
Modeling Of Vapor Sorption In Nanoparticle Chemiresistors, Alexandra Oliveira
Honors Scholar Theses
Chemical vapor sensors possess a number of uses in a variety of fields, from environmental and health monitoring to food safety and national security concerns, such as the detection of improvised explosive devices. Many sensors currently in the market have the ability to detect the presence of a select few compounds and measure the concentration at which the species is present. However, these types of sensors require that the vapor to be investigated is known beforehand; they cannot be used for identification except on a case by case basis. In response to this issue, one branch of vapor sensor research …
How Moisture Content Levels And Packing Density In Soil Affect Crude Oil Spreads,
2019
University of Mississippi
How Moisture Content Levels And Packing Density In Soil Affect Crude Oil Spreads, Shaylin N. Williams
Venture: The University of Mississippi Undergraduate Research Journal
Crude oil spills are one of the most destructive disasters that can occur, and they are extremely difficult to recover from. Many studies focus on what can be done to clean these crude oil spills, but more research should be focused on means of prevention. Currently, very little is known about how the moisture content levels and the packing efficiency of soil can affect an oil spill. These two factors alone can offer a variety of information to environmental agencies, manufacturers, and refineries. Through utilization of a chemical engineering lab, a recording mechanism, and ImagePro software, data was collected and …
Plasma-Assisted Liquid Phase Epitaxy Of Gallium Nitride Using Molten Gallium.,
2019
University of Louisville
Plasma-Assisted Liquid Phase Epitaxy Of Gallium Nitride Using Molten Gallium., Daniel Felipe Jaramillo-Cabanzo
Electronic Theses and Dissertations
Next generation semiconductor materials such as Gallium Nitride (GaN) and Silicon Carbide (SiC) are rapidly replacing Silicon (Si) for high power and high frequency applications due to Si’s inherent limitations. Despite the advantages of GaN over SiC, adoption of GaN has been hindered due to the lack of a cost-effective bulk production technique. Thus, the inability to precure native substrates requires GaN-based architectures to be heteroepitaxially synthesized on non-native substrates, such as sapphire and even SiC. This research seeks to develop a cost effective and scalable method to produce low defect, bulk GaN encouraging the adoption of GaN based devices …
Using Green Emitting Ph-Responsive Nanogels To Report Environmental Changes Within Hydrogels: A Nanoprobe For Versatile Sensing,
2019
University of Manchester
Using Green Emitting Ph-Responsive Nanogels To Report Environmental Changes Within Hydrogels: A Nanoprobe For Versatile Sensing, Mingning Zhu, Dongdong Lu, Shanglin Wu, Qing Lian, Wenkai Wang, L. Andrew Lyon, Weiguang Wang, Paulo Bártolo, Brian R. Saunders
Engineering Faculty Articles and Research
Remotely reporting the local environment within hydrogels using inexpensive laboratory techniques has excellent potential to improve our understanding of the nanometer-scale changes that cause macroscopic swelling or deswelling. Whilst photoluminescence (PL) spectroscopy is a popular method for such studies this approach commonly requires bespoke and time-consuming synthesis to attach fluorophores which may leave toxic residues. A promising and more versatile alternative is to use a pre-formed nanogel probe that contains a donor/acceptor pair and then “dope” that into the gel during gel assembly. Here, we introduce green-emitting methacrylic acid-based nanogel probe particles and use them to report the local environment …
Removal And Reuse Of Phosphorus As A Fertilizer From Cafo Runoff,
2019
University of Arkansas, Fayetteville
Removal And Reuse Of Phosphorus As A Fertilizer From Cafo Runoff, Hannah Young
Chemical Engineering Undergraduate Honors Theses
Eutrophication is the process in which nutrient saturated waters promote algal blooms on the surface of the water. This limits the amount of dissolved oxygen content in the water, effectively limiting the range of species that can survive in a body of water. Concentrated animal feeding operations (CAFO) can contribute to this issue. The animals in a CAFO produce large amounts of nutrient-rich waste streams that can enter natural waterways if not properly managed and increase the problem of eutrophication. The ability to treat these waste streams and recover the excess nutrients would allow for not only the reduction of …
Removal And Reuse Of Phosphorus As A Fertilizer From Cafo Runoff,
2019
University of Arkansas, Fayetteville
Removal And Reuse Of Phosphorus As A Fertilizer From Cafo Runoff, Kristin Moore
Chemical Engineering Undergraduate Honors Theses
Eutrophication is the process in which nutrient saturated waters promote algal blooms on the surface of the water. This limits the amount of dissolved oxygen content in the water, effectively limiting the range of species that can survive in a body of water. Concentrated animal feeding operations (CAFO) can contribute to this issue. The animals in a CAFO produce large amounts of nutrient-rich waste streams that can enter natural waterways if not properly managed and increase the problem of eutrophication. The ability to treat these waste streams and recover the excess nutrients would allow for not only the reduction of …
Scale Model And Flow Visualization Of Jack Rabbit Ii Chlorine Field Test,
2019
University of Arkansas, Fayetteville
Scale Model And Flow Visualization Of Jack Rabbit Ii Chlorine Field Test, Charlotte Williams
Chemical Engineering Undergraduate Honors Theses
The release of hazardous gases, especially accidental releases, can have a major impact on the surrounding environment and population. The history of accidental hazardous gas releases is filled with plant destruction, civilian injury, and even death. Knowledge of how these gases travel and disperse once released can significantly lessen physical harm and improve emergency procedures. The Jack Rabbit II field test was conducted in pursuit of this knowledge for a chlorine release. In this field test, a purpose-built chlorine tank was surrounded by CONEX trailers assembled in the desert in Utah to model an urban setting. Multiple releases of chlorine …
Nanogels And Microgels: From Model Colloids To Applications, Recent Developments, And Future Trends,
2019
Heinrich-Heine-University
Nanogels And Microgels: From Model Colloids To Applications, Recent Developments, And Future Trends, Mattias Karg, Andrij Pich, Thomas Hellweg, Todd Hoare, L. Andrew Lyon, J. J. Crassous, Daisuke Suzuki, Rustam A. Gumerov, Stefanie Schneider, Igor I. Potemkin, Walter Richtering
Engineering Faculty Articles and Research
Nanogels and microgels are soft, deformable, and penetrable objects with an internal gel-like structure that is swollen by the dispersing solvent. Their softness and the potential to respond to external stimuli like temperature, pressure, pH, ionic strength, and different analytes make them interesting as soft model systems in fundamental research as well as for a broad range of applications, in particular in the field of biological applications. Recent tremendous developments in their synthesis open access to systems with complex architectures and compositions allowing for tailoring microgels with specific properties. At the same time state-of-the-art theoretical and simulation approaches offer deeper …
Iron-Containing Nanoparticles For The Treatment Of Chrionic Biofilm Infections In Cystic Fibrosis,
2019
University of New Mexico - Main Campus
Iron-Containing Nanoparticles For The Treatment Of Chrionic Biofilm Infections In Cystic Fibrosis, Leisha M. A. Martin
Nanoscience and Microsystems ETDs
Cystic fibrosis (CF) is the most common genetic disease resulting in the morbidity and mortality of Caucasian children and adults worldwide. Due to a genetic mutation resulting in malfunction of the Cystic Fibrosis Transmembrane Conductance Regulator (CFTR) protein, CF patients produce highly viscous mucus in their respiratory tract. This leads to impairment of the mucociliary clearance of inhaled microbes. In addition to reduced microbial clearance, anoxic environmental conditions in the lungs promote biofilm-mode growth of the pathogenic bacterial species Pseudomonas aeruginosa. Chronic infections of P. aeruginosa begin in early childhood and typically persist until respiratory failure and death result. The …
Hazard And Operability Analysis Of An Ethylene Oxide Production Plant,
2019
University of South Carolina
Hazard And Operability Analysis Of An Ethylene Oxide Production Plant, Samantha Ciricillo
Senior Theses
The purpose of this work was to evaluate potential hazards and failures as part of the design and economic analysis for a chemical plant that would produce 150,000 tons of ethylene oxide per year. The Hazard and Operability (HAZOP) method of analysis was used to accomplish this goal. This method of hazard analysis involves brainstorming potential errors in a system by examining each element of each process unit in full detail. This project was focused on the reactor unit because the reactor has several important parameters that could fail, resulting in safety issues within the system. Input for this analysis …
Improving The Distribution And Use Of Biogas By Conversion To Methanol,
2019
University of Nebraska-Lincoln
Improving The Distribution And Use Of Biogas By Conversion To Methanol, Zachary Christman
Department of Agronomy and Horticulture: Dissertations, Theses, and Student Research
In this technology review, the process of turning an average biogas into methanol will be presented. The purpose is to find a better method of transporting the energy contained within biogas so that it may be used in industry as a value added product. The first step is removal of hydrogen sulfide, a corrosive chemical that can breakdown mechanical parts. The second step is carbon capture and conversion of the biogas into hydrogen. The final step is the hydrogenation of carbon dioxide into methanol using a copper catalyst and an alcohol co-catalyst.
Understanding Effects Of Engineering Outreach On Elementary Students,
2019
The University of Akron
Understanding Effects Of Engineering Outreach On Elementary Students, Thomas Cobb
Williams Honors College, Honors Research Projects
Currently, there is a desire to increase engineering understanding held by elementary students. As such, there needs to be a way to stimulate not only engineering, but other science, technology, engineering, and mathematics (STEM) topics in a young student’s lifestyle. One way to emphasize the importance of STEM while also showing how fun it can be is through different hands on activities led by individuals partaking in undergraduate studies or the industry. While having the students participate in the activities, it is important to understand what the students are learning and how the activity overall is viewed. With the help …
Novel Adsorbent For Industrial Wastewater Treatment Applications,
2019
The British University in Egypt
Novel Adsorbent For Industrial Wastewater Treatment Applications, Islam M. Al-Akraa, Ahmed Y. Zakaria Eng, Dalia A. Ali Eng, Hany A. Elazab Dr, Hoda A. Elsawy Dr
Chemical Engineering
In this study, the hydroxyapatite powder is investigated for both of methylene blue and thymol blue in aqueous solution. The physical and chemical properties of the adsorbent were evaluated systematically using the different techniques including Microsoft Excel programming, linear regression model and also the coefficient of determination. Batch adsorption experiments were conducted to determine the effect of contact time, solution pH, initial dye concentrations, and also the adsorbent dosage on adsorption. The adsorption kinetic parameters confirmed the better fitting of pseudo-second order kinetic model for both of methylene blue and thymol blue. The isotherm data of methylene blue and thymol …
Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community,
2019
The University of Akron
Improving The Delivered Specific Impulse Of Composite Rocket Propellant Through Alteration Of Chemical Composition: Methodology And Parameters For Characterization Of Propellant And Validation Of Simulation Software Common To The Amateur Rocketry Community, Isaac O'Brien, Austin Ryan
Williams Honors College, Honors Research Projects
In this study, two solid composite rocket propellants were designed utilizing ProPEP, a rocket propellant formulation software common in the amateur and hobby rocketry communities. The two propellants were designed to optimize specific impulse relative to a literature propellant designed by 1020 Research Labs. The literature propellant was also tested in order to validate the design of experiment as well as the mixing and testing procedures. All three propellants, which includes the literature propellant RCS-P, and the two novel propellants AKR-P1 and AKR-P2 were characterized with static tests. The results of the static tests provide data on propellant performance and …
Fluidized Bed Classroom Demonstration Unit,
2019
The University of Akron
Fluidized Bed Classroom Demonstration Unit, Theresa Chapa
Williams Honors College, Honors Research Projects
Fluid and Thermal Operations is a 4th year chemical engineering course at the University of Akron designed to introduce undergraduate students to the engineering and mathematical concepts behind the operation of a fluidized bed. The purpose of this honors project is to design and manufacture an inexpensive and portable unit that can be used in the classroom to visually demonstrate three functions of a fluidized bed to students. The fluidized bed is manufactured from items that can be purchased from a department or hardware store, is capable of being transported by a single person to and from a classroom and …
Using Fluorescence Spectroscopy To Determine Concentrations Of Quantum Dot Solutions,
2019
University of Alabama in Huntsville
Using Fluorescence Spectroscopy To Determine Concentrations Of Quantum Dot Solutions, Cameron Sawyer
Summer Community of Scholars Posters (RCEU and HCR Combined Programs)
No abstract provided.
Cataloging The Degree Of Sensitization Via Electrochemical Reactivation For Studying The Corrosion Behavior Of Inconel 718, Austenitic, And Duplex Stainless Steels,
2019
The University of Akron
Cataloging The Degree Of Sensitization Via Electrochemical Reactivation For Studying The Corrosion Behavior Of Inconel 718, Austenitic, And Duplex Stainless Steels, Bradley Lynes
Williams Honors College, Honors Research Projects
Corrosion resistant materials can be expensive, but usually reduce the life cycle cost of metallic assets. However, negligent sensitization of these materials can lead to aggressive, intergranular corrosion. Using the methodology of the double loop electrochemical potentiokinetic reactivation (DL-EPR), this project investigates different steel reinforced bars and Inconel to determine the degree of sensitization after a heat treatment of 900°C for 2 hours. The purpose of this research is to validate and determine the appropriate test parameters for performing further DL-EPR test in the future. Additionally, the kinetics observed for each sample during the DL-EPR test will be analyzed and …
Effects Of Hofmeister Ions On Transition Temperature Of Two Thermo-Responsive Polymers,
2019
The University of Akron
Effects Of Hofmeister Ions On Transition Temperature Of Two Thermo-Responsive Polymers, Joshua Moser
Williams Honors College, Honors Research Projects
It was hypothesized that through the use of Hofmeister Ions, the lower critical solution temperature (LCST) of poly(vinyl methyl ether) (PVME) and poly(ethylene glycol)- poly(N-isopropylacrylamide) (PEG-b-pNIPAAm) block-copolymer could be controlled. Through literature searches and small lab experiments, our team found that there may be a connection between Hofmeister effects and phase transition of a thermo-responsive polymer. To try and prove this, the lab team decided to take four cations (Mg2+,Na+, Cs+, K+) in solution with the thermo-responsive polymers and compared their LCST to solutions of the thermo-responsive polymer in de-ionized …
Form Stable Phase-Change Materials,
2019
University of Akron
Form Stable Phase-Change Materials, Russell Dent, Marjan Kashfipour, Nitin Mehra, Jiahua Zhu
Williams Honors College, Honors Research Projects
This work investigates the use of two different polyols, xylitol (Xyl) and erythritol (Ery), in conjunction with boron nitride (BN) aerogels, for the purpose of creating thermally conductive composites. While the BN filler in Xyl composites achieved a high anisotropic thermal conductivity of up to 4.53 W/m-K at 18.2 weight percent filler loading, they do not exhibit good phase-change material qualities due to a low solidification enthalpy even at low cooling rates. Alternatively, the BN-Ery composites have shown promising results with a solidification enthalpy of 225.14 J/g and a melting enthalpy of 385.84 J/g at a heat rate of 5 …
