Dental Materials Commons^™

Differentiation Of Dental Pulp Stem Cells Into Islet-Like Aggregates, Noor Hayaty Abu Kasim Abu Kasim N.H.

Noor Hayaty Abu Kasim Abu Kasim N.H.

The post-natal dental pulp tissue contains a population of multipotent mesenchymal progenitor cells known as dental pulp stromal/stem cells (DPSCs), with high proliferative potential for self-renewal. In this investigation, we explored the potential of DPSCs to differentiate into pancreatic cell lineage resembling islet-like cell aggregates (ICAs). We isolated, propagated, and characterized DPSCs and demonstrated that these could be differentiated into adipogenic, chondrogenic, and osteogenic lineage upon exposure to an appropriate cocktail of differentiating agents. Using a three-step protocol reported previously by our group, we succeeded in obtaining ICAs from DPSCs. The identity of ICAs was confirmed as islets by dithiozone-positive …

Frictional Resistance Of Aesthetic Orthodontic Arch Wires Compared To Traditional Arch Wires Before And After Toothbrush Abrasion, Stephen Yamodis, Jeremy Manuele, Adam Kessler, Brendan O'Toole, James Mah, Bob Martin

Festival of Communities: UG Symposium (Posters)

Our objective was to compare frictional resistance evident in aesthetic archwires to traditional (non-aesthetic) archwires. Methods: Archwires ligated with elasatics to fixed brackets were pulled through these brackets while frictional resistance (in lbf) was measured. Results: There were no confirmed significant differences between the frictional resistance of the aesthetic arch wires compared to the traditional non-coated wires for all wire sizes tested Conclusions: Our data suggests that a sacrifice of clinical performance with these aesthetic archwires as compared to traditional archwires is not likely

Structural And Compositional Characterization Of Silverfil Amalgam, Noor Hayaty Abu Kasim Abu Kasim N.H.

Noor Hayaty Abu Kasim Abu Kasim N.H.

SilverFil (Silverfildental Products, Malaysia) is another commercially available dental amalgam; however it is based on silver and mercury only. It is claimed that upon amalgamation, there is no excess mercury in SilverFil. Objectives: The objectives of this study were to determine the structural state and chemical composition of the starting materials and presence of mercury in the resulting amalgam. Methods: All the starting materials of SilverFil and the SilverFil amalgam specimens were characterize using Field Emission Scanning Electron Microscopy (FESEM-EDX), X-Ray Diffraction (XRD) and X-Ray Photoelectron Spectroscopy (XPS). Results: The FESEM images of the amalgam shows silver-mercury (Ag-Hg) clusters. The …

The Evolution Of Prophy Paste, Caren M. Barnes

College of Dentistry: Faculty Publications

Dental hygienists have many products to choose from when deciding which prophy paste is best for each patient. To date, the evidence supporting prophy pastes formulated to remineralize enamel or eliminate dentinal hypersensitivity is somewhat unclear. Most of the research has been conducted in vitro among environments that do not accurately simulate clinical conditions. Additional clinical research performed in vivo is needed to provide the evidence base necessary for effective clinical decision making.

Fracture Resistance Of Endodontically Teeth Restored With Functionally Graded Posts, Ahmed A. Madfa

Ahmed A. Madfa

Objectives: To evaluate the fracture resistance and failure mode of endodontically teeth restored with functionally graded structured (FGS) posts compared to titanium and cast posts. Methods: Single canals in 70 bovine incisors were instrumented, irrigated, obturated and divided into seven groups. They were then root restored with titanium, cast and 3 experimental FGS posts of different compositions; ZrO2-Ti-HA, Al2O3-Ti-HA and Ti-HA. Two control groups were also included; sound teeth and those root treated only. All posts were cemented with zinc phosphate cement and built up with composite core. Crowns margins of 1 mm chamfer finishing line were prepared to receive …

3d-Fe Analysis Of Functionally Graded Structured Dental Posts, Ahmed A. Madfa

Ahmed A. Madfa

This study aimed to compare the biomechanical behaviour of functionally graded structured posts (FGSPs) and homogenous-type posts in simulated models of a maxillary central incisor. Two models of FGSPs consisting of a multilayer xTi-yHA composite design, where zirconia and alumina was added as the first layer for models A and B respectively were compared to homogenous zirconia post (model C) and a titanium post (model D). The amount of Ti and HA in the FGSP models was varied in gradations. 3D-FEA was performed on all models and stress distributions were investigated along the dental post. In addition, interface stresses between …

Optimization Of Microencapsulation Process For Self-Healing Polymeric Material, Noor Hayaty Abu Kasim Abu Kasim N.H.

Noor Hayaty Abu Kasim Abu Kasim N.H.

A series of poly(urea-formaldehyde) (PUF) microcapsules filled with dicyclopentadiene (DCPD) was successfully prepared by in situ polymerization. The effect of diverse process parameters and ingredients on the morphology of the microcapsules was observed by SEM, optical microscopy (OM) and digital microscopy. Different techniques for the characterization of the chemical structure and the core content were considered such as FT-IR and (1)H-NMR as well as the characterization of thermal properties by DSC. High yields of free flowing powder of spherical microcapsules were produced. The synthesized microcapsules can be incorporated into another polymeric host material. In the event the host material cracks …

3d-Fe Analysis Of Functionally Graded Structured Dental Posts, Noor Hayaty Abu Kasim Abu Kasim N.H.

Noor Hayaty Abu Kasim Abu Kasim N.H.

This study aimed to compare the biomechanical behaviour of functionally graded structured posts (FGSPs) and homogenous-type posts in simulated models of a maxillary central incisor. Two models of FGSPs consisting of a multilayer xTi-yHA composite design, where zirconia and alumina was added as the first layer for models A and B respectively were compared to homogenous zirconia post (model C) and a titanium post (model D). The amount of Ti and HA in the FGSP models was varied in gradations. 3D-FEA was performed on all models and stress distributions were investigated along the dental post. In addition, interface stresses between …

Thermo-Mechanical Stress In Multilayered Dental Post Due To Temperature Gradient, Noor Hayaty Abu Kasim Abu Kasim N.H.

Noor Hayaty Abu Kasim Abu Kasim N.H.

Objective: To analyse thermo-mechanical stress in endodontically treated teeth restored with Multilayered Structured Dental Posts (MSDPs) under cold and hot conditions using Finite Element Analysis (FEM). Methods: Three MSDPs of multilayer design of xTi-yHA composition added to a zirconia layer (model A), an alumina layer (model B) and a titanium layer (model C) were compared with zirconia (model D) and titanium (model E) posts. The fractions of Ti and HA was varied gradually. Changes in temperature of an endodontically restored tooth model were calculated as a result of hot and cold response. The resulting thermo-mechanical stresses were analysed and compared …

Work Of Fracture In Ceramic Bracket Bonding Systems, Tye A. Roylance

Loma Linda University Electronic Theses, Dissertations & Projects

Introduction: Work of fracture (WOE) is a method of analysis of the toughness or resilience of a bracket bonding system. It is an indication of a bracket bonding systems ability to withstand forces in the mouth below the force at which failure occurs. Work of fracture gives an indication of how much abuse the bracket/bonding system can withstand and still maintain an adequate adhesion to the tooth surface. This analysis incorporates shear bond strength and displacement and is determined in part by the elasticity and resilience of the specimen being studied.

Materials and Methods: One hundred and eighty bovine teeth …

Inherent Differential Propensity Of Dental Pulp Stem Cells Derived From Human Deciduous And Permanent Teeth, Noor Hayaty Abu Kasim Abu Kasim N.H.

Noor Hayaty Abu Kasim Abu Kasim N.H.

Introduction: Lately, several new stem cell sources and their effective isolation have been reported that claim to have potential for therapeutic applications. However, it is not yet clear which type of stem cell sources are most potent and best for targeted therapy. Lack of understanding of nature of these cells and their lineage-specific propensity might hinder their full potential. Therefore, understanding the gene expression profile that indicates their lineage-specific proclivity is fundamental to the development of successful cell-based therapies. Methods: We compared proliferation rate, gene expression profile, and lineage-specific propensity of stem cells derived from human deciduous (SCD) and permanent …

Dentoskeletal And Soft Tissue Treatment Effects Of Two Different Methods For Treating Class Ii Malocclusions., Madhur Upadhyay

Master's Theses

Objectives: Moderate to severe Class II malocclusions can not only cause esthetic and functional problems but can also lead to psychological problems of varying intensity depending on the amount of anterior-posterior discrepancy and its interaction with the related soft tissue structures. Although there are several methods of treating such malocclusions (extractions,distalization,functional appliances etc), the final goal is always to provide acceptable esthetics and stability. The purpose of this clinical-cephalometric study was to examine the dentoskeletal and soft tissue treatment effects of maxillary anterior teeth retraction with mini-implant (MI) anchorage in young adults having Class II Division I malocclusion undergoing extraction …

Hydroxyl-Terminated Poly(Urethane Acrylate) As A Soft Liner In Dental Applications: Synthesis And Characterization, Selda Keskin

ABSTRACT: Hydroxyl-terminated poly(urethane acrylate) s were synthesized for use in biomedical applications. Acrylate end capping via an interesterification reaction was successfully achieved with methacryloyl chloride addition to the hydroxyl ends of the polyurethane at low temperatures. 2,4-Toluene diisocyanate, 1,6-hexane diisocyanate, and methylene diphenyl diisocyanate were used as diisocyanates for urethane synthesis, and they were end-capped with methyl methacrylate and hydroxyethyl methacrylate. The nature of the monomers that we used had an effect on the thermal and morphological properties that were interpreted in terms of the level of hydrogen bonding and the degree of phase separation. The synthesized polymers were characterized …

An In-Depth Look At Air Polishing, Caren M. Barnes

College of Dentistry: Faculty Publications

Air polishing has been available for four decades, however, the concept is based on a technology invented by Dr. Robert Black in 1945. Dr. Black invented the Air Dent, a device that used compressed air, water, and a highly abrasive powder to eliminate pain from cavity preparation, making anesthesia unnecessary. The Air Dent had numerous problems that could not be overcome, but Dr. Black never gave up on his idea. The technology he invented became the basis of air polishing and was first marketed in 1976. By the late 1970s, air polishing was readily available.

Air polishing represents the most …

Microtensile Bond Strength Of Self-Adhesive Resin-Based Dental Cement, Selda Keskin

This study investigated the effectiveness of bleaching agents on the micro tensile bond strength (mTBS) of self-adhesive luting cement and enamel. A total of 126 samples were prepared from the labial surfaces of permanent human maxillary central incisors and assigned into three groups with 42 samples each as: control, enamel bleached with 10% hydrogen peroxide (HP), and enamel bleached with 10% carbamide peroxide (CP). Rely X Unicem1 (3 M, ESPE) was used as self-adhesive resin cement. The total testing period for bleaching was selected as 14 days and the bleaching agents were applied 8 hours a day. The statistical one-way …

Polishing Esthetic Restorative Materiai, Caren M. Barnes

College of Dentistry: Faculty Publications

When esthetic dental restorations are encountered during charting, they should be included in the treatment plan for the specific polishing procedures that are required. If the brand and type of esthetic restoration are known through the patient chart, the polishing procedures and products used should be those recommended by the manufacturer. If not possible, alternative polishing procedures should be used. A cleaning agent containing feldspar and rubber polishing cup can be used on all esthetic restorative materials with no chance of damage to the surface characterization.

The principles for polishing esthetic restorations are the same as for natural teeth. If …

Effect Of Au And Au@Ag Core-Shell Nanoparticles On The Sers Of Bridging Organic Molecules., Remziye Guzel Dr., Zafer Ustundag Dr., Haslet Eksi, Selda Keskin Dr., Bilge Taner, Zeynep Durgun, Ali Osman Solak Prof. Dr.

No abstract provided.

New Generation Of The Dental Posts For Endodontic Application., Ahmed A. Madfa

Ahmed A. Madfa

Fabricated multilayer dental post with the functionally graded design is a novel product that exhibits graded properties varied from coronal to apical parts of the tooth. The new dental post definitely performs better than posts available in the market and improves the quality of human life

Cytotoxicity Of Polyurethane Dimethacrylate Derived From Palm Oil Polyol., Noor Hayaty Abu Kasim Abu Kasim N.H.

Noor Hayaty Abu Kasim Abu Kasim N.H.

Objective: The aim of this study was to investigate the cytotoxicity effect of polyurethane dimethacrylate monomer derived from palm oil polyol (PUDMA) and 2 experimental composite resins based on these monomer PUDMA- based composites) compared to an experimental Bis-GMA/TEGDMA-based composite and EsthetX flowable composite (Dentsply, Caulk, USA). Methods: The experimental composite resins were prepared by mixing 0.25% and 0.75% by weight camphorquinone and ethyl (4-dimethyl amino) benzoate with 60% filler for each of the following monomer systems; I) PUDMA monomer (PUDMA-based composite resin), II) Bis-GMA/TEGDMA at ratio of 75:25 by weight, III) PUDMA/BisGMA-TEGDMA at ratio of 50:50 by weight. Eight …

Surface Reproduction Of Elastomeric Materials: Viscosity And Groove Shape Effects, Noor Hayaty Abu Kasim Abu Kasim N.H.

Noor Hayaty Abu Kasim Abu Kasim N.H.

Objective: To evaluate the effect of viscosity and type of grooves on surface detail reproduction of elastomeric impression materials. Methods: Express putty/light-, Impregum medium- and heavy/light-bodied and Aquasil medium- and putty/light-bodied elastomeric impression materials were chosen for this study. Five impressions were made using a cylindrical aluminum reference block with U- and V- shaped grooves and to produce 35 master dies. Each master die was immersed in distilled water at 370 C for 5 minutes prior to the impression making on moist surfaces. Surface topography of the dies and impressions were captured using Alicona Imaging System. The mean difference in …