Materials Chemistry Commons^™

Applications Of N-Methyl-N-Butyl-Pyrrolidinium Bromide And N-Methyl-N-Ethyl-Pyrrolidinium Bromide In Zn-Br Flow Batteries, Qi Zhang, Miao-Miao Zhang, Lin Meng

Journal of Electrochemistry

It is extremely important for battery performance and safety in Zn-Br flow battery to use quaternary ammonium salts as complex agents for bromine. In this work, the effects of electrolyte compositions and concentrations on the electrode reactions and battery performances were studied in the absence and presences of N-methyl-N-ethyl-pyrrolidinium bromide (MEP) or N-methyl-N-butyl-pyrrolidinium bromide (MBP). The conductivities in the electrolytes containing different constitutions and concentrations were measured by EIS method. The charge-discharge performance for the battery and the complex ability for bromine in different electrolytes were also investigated. The results showed that the electrolyte containing MBP was better than that …

Kinetics And Mechanism Toward Electrochemical Reductions Of Sodium Bromide And Methanol Over Iron Electrodes, Qun Liao, Shu-Feng Zhang, Wen-Hua Leng

Journal of Electrochemistry

It is of technological value and scientific interest to the electro-synthesis of ferrocene, conversion of carbon dioxide (CO₂) and organic electro-synthesis in non-aqueous solutions by investigating the kinetics and mechanism toward electrochemical reductions of sodium bromide (NaBr) and methanol over iron electrodes. However, few reports in the related researches are available. In this article, the kinetics and mechanism toward electrochemical reductions of NaBr and methanol over iron electrodes were examined in detail by carrying out the polarization curve and electrochemical impedance spectroscopic measurements. The results showed that methanol was the reactant, while Na⁺ ions were functioned only …

Effect Of Peg-Coating On Properties Of Lithium-Sulfur Battery Cathode Material Containing Carbon Fiber Conductive Agent, Jie-Cheng Tan, Yan-Hong Tian, Xue-Jun Zhang, Kai-Le Fan

Journal of Electrochemistry

The composite materials contained high modulus carbon fiber (HMCF) were successfully prepared by employing a ball-milling process based on the coating treatment of polyethylene glycol (PEG), and their structures and morphologies were characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) techniques．The influences of PEG content on sulfur cathode capacity, cycle stability and rate performance were systematically studied. It was found that by the pre-coating of PEG, the cathode exhibited the high initial discharge specific capacity of 1312.5 mAh⋅g^-1 at a current rate of 0.2C, and the reversible discharge capacity of 650 mAh⋅g …

Capacity Fading Analyses Of Lini0.5Co0.2Mn0.3O2And Lini0.5Co0.2Mn0.3O2/Lifepo4 Cathode Materials For Lithium-Ion Battery, Yi Hu, Xiang-Zhu He, Zhong-De Deng, Ling-Yong Kong, Wei-Li Shang

Journal of Electrochemistry

The LiNi _0.5Co _0.2Mn _0.3O₂/LiFePO₄ (NMC532/LFP) composite cathode material for lithium-ion battery was prepared by wet ball-milling. The capacity fading behaviors of LiNi _0.5Co _0.2Mn _0.3O₂ (NMC532) and LiNi _0.5Co _0.2Mn _0.3O₂/LiFePO₄ (NMC532/LFP) were analyzed by X-ray diffraction (XRD), scanning electron microscope (SEM), charge/discharge and electrochemical impedance spectroscopy (EIS) tests. The results indicated that the capacity retention values of NMC532/LFP were 97.80% and 86.48%, respectively, after 50 cycles and 60℃ high temperature storage. The NMC532/LFP exhibited better cycle performance and high temperature storage performance. …

Fabrication And Characterization Of Intricate Nanostructures, Treva T. Brown

LSU New Orleans Theses and Dissertations

Encapsulation of nanoparticles within hexaniobate nanoscrolls presents interesting advances in the formation of nanocomposites exhibiting unique multi-dimensional properties. Building upon previous successes, facile yet versatile wet-chemical and microwave-irradiation synthetic protocols for the fabrication of a series of hexaniobate composites are presented herein. Solvothermal and, more recently, microwave-assisted methods have been developed that allow for the fabrication of peapod-like structures. During solvothermal treatment, exfoliated hexaniobate nanosheets scroll around highly ordered chains of preformed nanoparticles (NPs) to produce nanopeapods (NPPs). This approach offers versatility and high yields, in addition to the potential for advanced functional device fabrication.

For the characterization of these …

Three-Dimensional Nanomaterials For Supercapacitor Applications: From Metal Oxides To Metal Phosphides, Zhi Zheng

LSU New Orleans Theses and Dissertations

Over the past few years, energy storage devices have received tremendous interest due to the increasing demand for sustainable and renewable energy in modern society. Supercapacitors are considered as one of the most promising energy storage devices because of their high power density and long cycle life. However, low energy density remains as the main shortcoming for supercapacitors. The overall performance of supercapacitors is predominantly determined by the characteristics of the electrodes. Specifically, constructing nanostructured electrode material has been proven as an efficient way to improve the performance by providing large surface area and short ionic and electronic diffusion paths. …

Synthesis And Characterization Of Thermoresponsive Hydrogels Based On N-Isopropylacrylamide Crosslinked With 4,4′-Dihydroxybiphenyl Diacrylate, Shuo Tang, Martha Floy, Rohit Bhandari, Manjula Sunkara, Andrew J. Morris, Thomas D. Dziubla, J. Zach Hilt

Chemical and Materials Engineering Faculty Publications

A novel crosslinker [4,4′-dihydroxybiphenyl diacrylate (44BDA)] was developed, and a series of temperature-responsive hydrogels were synthesized through free radical polymerization of N-isopropylacrylamide (NIPAAm) with 44BDA. The temperature-responsive behavior of the resulting gels was characterized by swelling studies, and the lower critical solution temperature (LCST) of the hydrogels was characterized through differential scanning calorimetry. Increased content of 44BDA led to a decreased swelling ratio and shifted the LCST to lower temperatures. These novel hydrogels also displayed resiliency through multiple swelling–deswelling cycles, and their temperature responsiveness was reversible. The successful synthesis of NIPAAm-based hydrogels crosslinked with 44BDA has led to a …

Artificial Olfactory System For Multi-Component Analysis Of Gas Mixtures., Alexander Aleksandrovich Larin

Electronic Theses and Dissertations

Gas analysis is an important part of our world and gas sensing technology is becoming more essential for various aspects of our life. A novel approach for gas mixture analysis by using portable gas chromatography in combination with an array of highly integrated and selective metal oxide (MOX) sensors has been studied. We developed a system with small size (7 x 13 x 16 inches), low power consumption (~10 W) and absence of special carrier gases designed for portable field analysis (assuming apriori calibration). Low ppb and even sub-ppb level of detection for some VOCs was achieved during the analysis …

Barrier Properties Of Polymer Nanocomposites With Graphene Oxide And Its Derivatives: Mechanism And Applications In Anticorrosive Coatings, Yidan Guan

Dissertations

Metallic devices made from steel or aluminum are subjected to deterioration by environmental contaminants over time. As one of the corrosion control methods, organic coatings show many advantages due to their low cost, versatility, decoration aesthetics and effective protections. Corrosion protection theories and failure modes of organic coatings are still not fully understood due to complicated interactions in the coating-metal-environment system, however, it is widely agreed that the barrier nature of polymeric materials towards aggressive species, such as oxygen, water, electrolyte, plays a key role. Improved barrier property of polymer nanocomposites (PNCs) with two-dimensional (2D) carbon filler, graphene and graphene …

The Role Of Carbon On Copper–Carbon Composites For The Electrooxidation Of Alcohols In An Alkaline Medium, Leticia García-Cruz, Conchi O. Ania, Ana Paula Carvalho, Teresa Bandosz, Vicente Montiel, Jesús Iniesta

Publications and Research

Copper–carbon composites were prepared following various different synthetic routes and using various carbon precursors (i.e., lignocellulose and graphite oxide), andwere used as electrocatalysts for the oxidation of propargyl alcohol (PGA) in an alkaline medium. The electrochemical response of the copper-based catalysts was analyzed in terms of the influence of the metallic species, the carbon matrix incorporated in the composites, and the chemical structure of the ionomers—Nafion and poly (4-vinylpyridine) cross-linked methyl chloride quaternary salt resin (4VP)—used in the fabrication of the electrodes. Data has shown that the incorporation of reduced graphene oxide sheets between the copper metallic particles increased the …

Investigating Scalable Manufacturing Of High-Conductivity Wires And Coatings From Ultra-Long Carbon Nanotubes, Pouria Khanbolouki

Mechanical Engineering ETDs

Carbon nanotubes (CNTs) are a promising candidate for next generation of electrical wirings and electromagnetic interference (EMI) shielding materials due to their exceptional mechanical and electrical properties. Wires and coatings from ultralong nanotubes that are highly crystalline, well-aligned and densely packed can achieve this goal. High-performance CNT conductors will be relatively lightweight and resistant to harsh conditions and therefore can potentially replace current conductors in many industries including aerospace, automotive, gas and oil.

This thesis investigates a new manufacturing approach, based on conventional solution coating and wire drawing methods, to fabricate high conductivity wires and coatings from ultra-long carbon nanotubes. …

Superconductivity At Т≈200 K In Bismuth Cuprates Synthesized Using Solar Energy, J. Chigvinadze, Juana Acrivos, S. Ashimov, D. Gulamova, G. Donadze

Faculty Publications, Chemistry

When investigating low-frequency (0.1 Hz) oscillations of multiphase high-temperature cuprate superconductors (HTCS) Bi1,7Pb0,3Sr2Ca(n-1)CunOy (n=2-30), a wide attenuation peak (ΔT~100 К) with a maximum at Т≈200 К was detected. This peak was particularly pronounced in field cooling (FC) experiments, i.e. after abrupt cooling of the sample in the external magnetic field at the temperature Т<Тс with subsequent slow warming up to room temperature with invariance of the applied field. The attenuation peak height depended on the preliminaryorientation (before cooling) of the samples θ in the measured permanent magnetic field Н. On the one hand, it is well known that, after the FC procedure and subsequent slow warming up, at the temperatures close to the critical temperature Тс, the attenuation peak associated with “melting” of the Abrikosov frozen vortex structure and its disappearance at Т >Тс is detected in monophase samples. At the same time, in most multiphase bismuth HTCS samples, synthesized using solar energy and superfast quenching of the melt, the attenuation peak with the maximum at Т≈200 К was observed.Depending on the conditions of synthesis, the attenuation peak could …

Special Issue On Supercapacitors, Xiao-Gang Zhang

Journal of Electrochemistry

/

Strategies To Enhance Energy Density For Supercapacitors, Jun-Wei Lang, Xu Zhang, Ru-Tao Wang, Xing-Bin Yan

Journal of Electrochemistry

The biggest advantage of supercapacitor lies in not only the excellent pulse and fast charging-discharging performance, but also the characteristics of long cycle life and wide operating temperature window with no pollution. However, the energy density of supercapacitor is low. In this paper, the working principle, the development status, defects and improvement method of supercapacitors are introduced. Based on the research workes of the supercapacitors with high energy density in our group, combined with the literature reports in recent years, the strategies to promote the energy density of supercarpacitors will be focused. The strategies for the enhancement of energy density …

Porous Carbon Materials Produced By Koh Activation For Supercapacitor Electrodes, Jiang-Lin Ye, Yan-Wu Zhu

Journal of Electrochemistry

Porous carbon materials with high specific surface area and excellent conductivity have wide applications in supercapacitor electrodes. Much effort has been made to synthesize and tailor the microstructures of porous carbon materials via various activation procedures (physical and chemical activations). In particular, the chemical activation using potassium hydroxide (KOH) as an activating reagent is promising because of the well-defined micropore size distribution and ultrahigh specific surface area up to 3000 m²·g^-1 of the resulting porous carbons. Based mainly on the previous works taken by the authors and collaborators in the field, we have summarized the activation mechanism …

Recent Advances On Carbon And Transition Metallic Compound Electrodes For High-Performance Supercapacitors, Dun Lin, Xi-Yue Zhang, Yin-Xiang Zeng, Ming-Hao Yu, Xi-Hong Lu, Ye-Xiang Tong

Journal of Electrochemistry

Supercapacitors (SCs) have stimulated intensive interests for their promising applications in electric vehicles and portable electronics, etc. Electrode material is the most important key component of SCs, which vastly determines the performance of SCs. Carbon and transition metallic compound materials have attracted considerable attention and been widely explored as electrode materials. However, the insufficient capacitance of carbon materials and unsatisfactory conductivity and cyclic stability of transition metallic compounds severely limit their implementation as robust SC electrodes. Herein, we highlight our recent efforts to boost the capacitive performance of carbon and metal oxide/nitride electrodes by rationally structural and componential design. The …

Lithium Ion Hybrid Capacitor With High Energy Density, Xian-Zhong Sun, Xiong Zhang, Kai Wang, Yan-Wei Ma

Journal of Electrochemistry

Lithium ion hybrid capacitors are electrochemical energy storage devices combining the advantages of both Li-ion battery and electrochemical capacitor. They can be extensively used in many fields. However, the commercialization of lithium ion hybrid capacitor has been encountered several problems, e.g., the device structure design, the screening of materials, the pre-lithiation process, and the interface between electrolyte and electrode, etc. This review summarizes the recent research advances in lithium ion hybrid capacitor with high energy density, including the selection of the active materials in cathode/anode and the separator, the pre-lithiation method using the three-electrode structure, the high- and low-temperature performances, …

Template Induced Fabrication Of Nitrogen Doped Carbon Sheets As Electrode Materials In Supercapacitors, Tao Huang, Guang-Zhi Tao, Chong-Qing Yang, Deng Lu, Lie Ma, Dong-Qing Wu

Journal of Electrochemistry

Due to the good electrical conductivity, high specific surface area, and excellent chemical/mechanical stability, carbon nanomaterials with two-dimensional morphology have gradually become the hot topic of the research on supercapacitors. Herein, we report for the first time the fabrication of nitrogen doped carbon sheets (NCSs). In our approach, the sheet-like magnisum aluminum (MgAl) layered double hydroxide was used as the hard template, which was mixed with o-phenylene diamine and iron chloride. The following thermal treatment could render the polymerization and carbonization of o-phenylene diamine. The NCSs with ordered hexagonal architectures were formed by final etching process of the thermally treated …

Preparation And Characterization Of Cellulose Acetate-Based Separator For Lithium-Ion Batteries, Hua-Feng Luo, Yuan-Dong Qiao

Journal of Electrochemistry

To improve the electrolyte wettability and thermal resistance of separators used for lithium-ion battery, a novel cellulose acetate (CA)-based separator is facilely prepared by non-solvent induced phase separation (NIPS) wet-process and investigated in lithium-ion batteries. Systematical investigations including morphological characterization, electrolyte wettability and thermal resistance testing were carried out. The results demonstrated that the CA-based separator exhibited well developed three-dimensional porous structures with porosity up to 65%, which is 1.5 times higher than that of PE separator. The CA separator also showed excellent electrolyte uptake (285%) and thermal stability at 150 ^oC for 30 min. Compared with the commercial …

Responsive Nanogel Probe For Ratiometric Fluorescent Sensing Of Ph And Strain In Hydrogels, Mingning Zhu, Dongdong Lu, Shanglin Wu, Qing Lian, Wenkai Wang, Amir H. Milani, Zhengxing Cui, Nam T. Nguyen, Mu Chen, L. Andrew Lyon, Daman J. Adlam, Anthony J. Freemont, Judith A. Hoyland, Brian R. Saunders

Engineering Faculty Articles and Research

In this study a new pH-responsive nanogel probe containing a complementary nonradiative resonance energy transfer (NRET) fluorophore pair is investigated and its ability to act as a versatile probe of network-related changes in three hydrogels demonstrated. Fluorescent sensing using NRET is a powerful method for studying relationships between Angstrom length-scale structure and macroscopic properties of soft matter. Unfortunately, inclusion of NRET fluorophores into such materials requires material-specific chemistry. Here, low concentrations of preformed nanogel probes were included into hydrogel hosts. Ratiometric photoluminescence (PL) data for the gels labeled with the nanogel probes enabled pH-triggered swelling and deswelling to be studied …