Analysis Of Electrodeposited Nickel-Iron Alloy Film Composition Using Particle-Induced X-Ray Emission,
2011
Hope College
Analysis Of Electrodeposited Nickel-Iron Alloy Film Composition Using Particle-Induced X-Ray Emission, Alyssa Frey, Nicholas Wozniak, Timothy Nagi, Matthew Keller, J. Mark Lunderberg, Graham F. Peaslee, Paul Deyoung, Jennifer R. Hampton
Faculty Publications
The elemental composition of electrodeposited NiFe thin films was analyzed with particle-induced X-ray emission (PIXE). The thin films were electrodeposited on polycrystalline Au substrates from a 100mM NiSO4, 10 mM FeSO4, 0.5M H3BO3, and 1M Na2SO4 solution. PIXE spectra of these films were analyzed to obtain relative amounts of Ni and Fe as a function of deposition potential and deposition time. The results show that PIXE can measure the total deposited metal in a sample over at least four orders of magnitude with similar fractional uncertainties. The technique is …
Heat Recovery Mechanism In The Excitation Of Radiative Polaritons By Broadband Infrared Radiation In Thin Oxide Films,
2011
James Madison University
Heat Recovery Mechanism In The Excitation Of Radiative Polaritons By Broadband Infrared Radiation In Thin Oxide Films, Anita J. Vincent-Johnson, Kyle A. Vasquez, John E. Bridstrup, Andrew E. Masters, Xiaofeng Hu, Giovanna Scarel
Department of Physics and Astronomy - Faculty Scholarship
This work probes radiative polaritons in thin oxide layers as a mean to capture and absorb broadband infrared radiation and transform it into heat. A heat recovery mechanism, based on the Seebeck effect, is used as the tool of the investigation. Heat production challenges the current understanding which views the excitation of radiative polaritons as only accompanied by the emission of electromagnetic radiation. The heat recovery mechanism presented here can inspire the design of infrared energy harvesting devices, similar to photovoltaic cells, and other devices to convert energy from a wide range of the electromagnetic radiation spectrum using thermoelectric power …
Fabrication And Catalytic Property Of Cerium Oxide Nanomaterials,
2011
University of Nebraska-Lincoln
Fabrication And Catalytic Property Of Cerium Oxide Nanomaterials, Keren Jiang
Department of Chemistry: Dissertations, Theses, and Student Research
Cerium oxide, or ceria (CeOx: x = 1.5 to 2), has been widely used as a heterogeneous catalyst. Ceria has several properties make it high catalytic active: the fluctuating valence of cerium, the high oxygen storage capacity and high oxygen mobility in the nonstoichiometric ceria. With the high abundance of cerium on earth crust, ceria is a highly effective alternative of the noble metal catalysts. Research has been focused on designing nanostructured ceria and ceria related materials in recent years. The catalytic activity of ceria can be enhanced by the nanoscale effect which can be applied for various …
Elastic Properties Of Poly(Vinyldene Fluoride) (Pvdf) Crystals: A Density
Functional Theory Study,
2011
University of Nebraska-Lincoln
Elastic Properties Of Poly(Vinyldene Fluoride) (Pvdf) Crystals: A Density Functional Theory Study, Yong Pei, Xiao Cheng Zeng
Xiao Cheng Zeng Publications
We computed structural and elastic properties of totally nine phases of poly(vinyldene fluoride) (PVDF) crystals using the density-functional theory (DFT) method with and without inclusion of the dispersion corrections. In addition to the four known crystalline forms, mechanic properties of five theoretically predicted crystalline forms of PVDF are also investigated. The all-trans form Ip exhibits the largest cohesive energy, bulk, and Young’s modulus among the nine crystalline forms. The DFT calculations suggest that the δ crystalline forms (IIIau, IIIpu, IIIpd, and IIIad) possess poor chain rigidity among the nine PVDF …
Structure Evolution Of Gold Cluster Anions Between The Planar And Cage Structures By Isoelectronic Substitution: AuN− (N = 13–15) And MauN− (N = 12–14; M = Ag, Cu),
2011
University of Nebraska-Lincoln
Structure Evolution Of Gold Cluster Anions Between The Planar And Cage Structures By Isoelectronic Substitution: AuN− (N = 13–15) And MauN− (N = 12–14; M = Ag, Cu), Rhitankar Pal, Lei-Ming Wang, Wei Huang, Lai-Sheng Wang, Xiao Cheng Zeng
Xiao Cheng Zeng Publications
The structural and electronic effects of isoelectronic substitution by Ag and Cu atoms on gold cluster anions in the size range between 13 and 15 atoms are studied using a combination of photoelectron spectroscopy and first-principles density functional calculations. The most stable structures of the doped clusters are compared with those of the undoped Au clusters in the same size range. The joint experimental and theoretical study reveals a new C3v symmetric isomer for Au13 −, which is present in the experiment, but has hitherto not been recognized. The global minima of Au14 − and Au …
A Practical Photoelectrochemical Cell Using Nonprecious Metal Electrodes,
2011
Technological University Dublin
A Practical Photoelectrochemical Cell Using Nonprecious Metal Electrodes, Patrick Enright, Tony Betts, John Cassidy
Articles
Abstract: Photoelectrochemical cells (PECs) can be used to harvest light from the oxidation of dissolved organic matter. Similar to fuel cells but requiring light to operate, PECs contain a light assisted electrode that oxidises electron rich materials (anode); these electrons then flow to a typically Pt cathode where O2 is normally the electron acceptor. In this work a PEC cell containing inexpensive materials was shown to (a) mineralise typical organic compounds present in waste water and (b) produce electricity from their decomposition. The PEC cell consisted of a TiO2 coated conducting ink anode exposed to a light source, …
Fabrication And Preliminary Characterization Of Hydrophobic Silica Aerogel Films For Oil Remediation Studies,
2011
Pomona College
Fabrication And Preliminary Characterization Of Hydrophobic Silica Aerogel Films For Oil Remediation Studies, Ellen Yang
Pomona Senior Theses
Due to the potential of oil sorbents for oil spill clean-up, hydrophobic silica-based aerogel thin films have been synthesized and characterized by various methods. Aerogels were prepared using a two-step acid/base sol-gel process and functionalized with trimethylchlorosilane in hexane, followed by drying in ambient conditions. After film deposition by spin-coating, samples were characterized by scanning electron microscopy, nitrogen adsorption analysis (BET surface area = 377.66 m2 /g), and variable-angle spectroscopic ellipsometry (thickness of 287.00 ± 0.85 nm, refractive index of 1.08, porosity of 80.9%). Unlike previous studies with aerogel films, quartz crystal microbalance with dissipation monitoring (QCM-D) was applied to …
Growth And Characterization Of Nanoscale Thin Films,
2011
University of Northern Iowa
Growth And Characterization Of Nanoscale Thin Films, Erik Thomas Wolter
Honors Program Theses
Thin manganese films were grown by thermal evaporation in high vacuum. The growth rate was varied to determine how the growth rate affects the continuity of ultra-thin films. The resistance was measured with the two-point method in situ and the data was recorded digitally. The resistance was converted to resistivity and this was plotted against thickness. It was found that resistivity decreases exponentially as the film begins to form in islands. The film reaches a critical thickness as the islands coalesce and the data can then be fitted with Fuchs’ equation. The resistivity continues to decrease but the minimum resistivity …
Electrochemical Detection For The Corrosion Of Reinforcing Steel In Concrete During Immersion And Drying Cycles,
2010
Department of Chemistry,Zhejiang University,Hangzhou 310027,China;
Electrochemical Detection For The Corrosion Of Reinforcing Steel In Concrete During Immersion And Drying Cycles, Bing-Li Jia, Fa-He Cao, An-Na Chen, Jian-Qing Zhang
Journal of Electrochemistry
The corrosion behavior of reinforcing steel in concrete under dry-wet cycle condition has been studied by electrochemical noise(EN) compared with the electrochemical impedance spectroscopy(EIS),SEM micrographs and EDS.The statistical method has been employed to analyze the EN data of reinforcing steel in concrete,which revealed three different corrosion stages of reinforcing steel in concrete,including the dissolution of the passive film,the active corrosion and the cumulation of corrosion product.The wavelet transform has also been employed,which indicated that steel in concrete with pH 1 is associated with uniform corrosion,while steel in concrete with pH 3 and pH 7 are associated with localized corrosion,such as …
Study On Preparing Technology And Corrosion Resistance Of Ti/Zr Based Chromium-Free Chemical Conversion Coating On Zinc Electroplating Layer,
2010
State Key Laboratory for Corrosion and Protection,Institute of Metal Research,Chinese Academy of Sciences,Shenyang 110016,China;
Study On Preparing Technology And Corrosion Resistance Of Ti/Zr Based Chromium-Free Chemical Conversion Coating On Zinc Electroplating Layer, Yong Guan, Jian-Guo Liu, Chuan-Wei Yan
Journal of Electrochemistry
In this paper,we obtained environmental-friendly chromium-free chemical conversion coating on the non-cyanide alkaline zinc electroplating layer by employing the optimized Ti/Zr based conversion technique.At the same time,the performances of the Ti/Zr based conversion coating were compared with chromate colour passivation coating.The corrosion resistances of the conversion coatings were investigated by using neutral salt spray(NSS) test,potentiodynamic polarization and electrochemical impedance spectroscopy(EIS).The results showed that the white rust appeared after 96 hours when the NSS test was performed on the Ti/Zr based conversion coating,which was close to the corrosion resistance rating of chromate colour passivation coating.Compared with the chromate passivation coating,the Ti/Zr …
The Sol-Gel Synthesis And Electrochemical Performance Of Li3V2(Po4)3/C Cathode Material For Lithium Ion Battery,
2010
Faculty of Material and Energy,Guangdong University of Technology,Guangzhou 518006,China;McNair Technology Co.Ltd,Dongguan 523800,Guangdong,China;
The Sol-Gel Synthesis And Electrochemical Performance Of Li3V2(Po4)3/C Cathode Material For Lithium Ion Battery, Li-Ying Liu, Lian Chen, Hai-Yan Zhang, Yu-Chun Zhai
Journal of Electrochemistry
Li3V2(PO4)3/C was synthesized by sol-gel method with citric acid as chelate and C sources. Physical and electrochemical performances of as-prepared materials were characterized through XRD, SEM and galvanostatic charge-discharge tests,etc. The results showed that products produced by calcining at 800 ℃ for 12 h had a single phase crystal structure and relatively small particle sizes with uniform distribution. At 0.1 C, 0.5 C and 1 C, the initial specific discharge capacities were 153.0, 143.1 and 130.6 mAh·g-1, respectively, and capacity efficiencies were 93.1%, 85.4% and 77.3% after 50 cycles, respectively. …
Study Of The 11-Ferrocenylalkanethiol Redox-Induced Structure Changes By Flow-Injection Electrochemical Surface Plasmon Resonance,
2010
School of Chemistry and Chemical Engineering,Central South University,Changsha 410083,Hunan,China;
Study Of The 11-Ferrocenylalkanethiol Redox-Induced Structure Changes By Flow-Injection Electrochemical Surface Plasmon Resonance, Xiu-Juan Xiao, Yong-Hui He, Juan Xiang, Bin Ren
Journal of Electrochemistry
Redox-induced orientation changes of self-assembled monolayers(SAMs) of 11-ferrocenylundecanethiol(FcC11SH) were studied by the flow-injection electrochemical surface plasmon resonance(FI-EC-SPR).Results indicated that there existed two mechanisms concerning the redox-induced structure change of the self-assembled monolayer of ferrocenylalkanethiols:the electrostatic repulsion between the positively charged surface and the ferricenium cation and that among the cations led to a decrease in the tilt angle of the alkanethiol chain;upon Fc oxidation,the Fc group rotated from a tilted conformation to a position where the cyclpentyldiene plane became perpendicular to the electrode.
Electroless Deposition And Characterization Of Nickel Coating In Lead-And Cadmium-Free Bath,
2010
State Key Laboratory of the Physical Chemistry of the Solid Surfaces,College of Chemistry and Chemical Engineering,Xiamen University,Xiamen 361005;
Electroless Deposition And Characterization Of Nickel Coating In Lead-And Cadmium-Free Bath, Fang-Zu Yang, Ming-Hui Chen, Xia-Jing Huang, Zhong-Qun Tian, Shao-Min Zhou
Journal of Electrochemistry
Technology of electroless nickel deposition in lead-and cadmium-free bath was developed.Coating′s morphology,composition,structure and electrochemical activity were characterized by SEM,EDS,XRD and electrochemical methods.The results showed that,the deposition rate of nickel in self-catalysing was 22.4 μm·h-1,which was increased by the increase of bath temperature and pH value.The effect of sodium hypophosphite on deposition rate was much more remarkable compared with nickel sulfate.The obtained nickel coating was 7.8% in phosphor weight content,having compact and neat surface morphology,amorphous structure,and good electrochemical corrosion resistance in sodium chloride solution.
Preparation And Characterization Of The Silane-Phosphonic Acid Composite Passivation Coating For Electrogalvanized Steel,
2010
State Key Laboratory for Corrosion and Protection,Institute of Metal Research,Chinese Academy of Sciences,Shenyang 110016,China;
Preparation And Characterization Of The Silane-Phosphonic Acid Composite Passivation Coating For Electrogalvanized Steel, Yong Guan, Jian-Guo Liu, Chuan-Wei Yan
Journal of Electrochemistry
A new silane-phosphonic acid composite passivation coating process has been developed for the protection of electrogalvanized steel based on N-(β-aminoethyl)-γ-aminopropyltrimethoxysilane(AAPTMS),γ-(2,3-epoxypropoxy)propyltrimethoxy-silane(GPTMS) and 1-hydroxy ethylidene-1,1-diphosphonic acid(HEDP).The results of X-ray photoelectron spectroscopy(XPS),Fourier transform infrared spectroscopy(FTIR),potentiodynamic polarization scan,electrochemical impedance spectroscopy(EIS) and neutral salt spray(NSS) tests indicated that the major structure of the prepared silane-phosphonic acid composite passivation coating consisted mainly of Si—O—Si and Si—O—P bonds.The area of white rust was not more than 5% of the total panal after 120 h NSS test,which could be compared favourably with the chromate colour passivation coating.However,the corrosion reaction on the anode of the silane-phosphonic acid composite passivation …
The Roles Of The Width Of Gas/Liquid/Solid Three-Phase Boundary Zone Of Dispersion Water Films In Atmospheric Corrosion Of Metals,
2010
College of Chemistry and Chemical Engineering,Ocean University of China,Qingdao 266100,Shandong,China;State Key Laboratory for Corrosion and Protection of Metals,Shenyang 110016,China;
The Roles Of The Width Of Gas/Liquid/Solid Three-Phase Boundary Zone Of Dispersion Water Films In Atmospheric Corrosion Of Metals, Jia Wang, Jing Jiang
Journal of Electrochemistry
The roles of TPB(Three-Phase Boundary) width in the corrosion processes of metals under dispersed water films were investigated by electrochemical techniques combined with contact angle measurement.It is found that both cathodic limiting current density and corrosion current density linearly increases with increasing the TPB width,confirming the important role of TPB width in gas/liquid/solid multiphase corrosion systems.Based on above results,the effect of water film thickness on atmospheric corrosion rate was quantitatively evaluated by the TPB width.
Initial Stage Of Atmospheric Corrosion Of Ndfeb(M35) In A Simulated Marine Atmosphere,
2010
State Key Laboratory for Corrosion and Protection,Institute of Metal Research,Chinese Academy of Sciences,Shenyang 110016,China;
Initial Stage Of Atmospheric Corrosion Of Ndfeb(M35) In A Simulated Marine Atmosphere, Chun-Ling Li, Yuan-Tai Ma, Ying Li, Fu-Hui Wang
Journal of Electrochemistry
This study detailed the atmospheric corrosion behaviour of sintered NdFeB(M35) in a simulated marine atmosphere with 80% relative humidity(RH).The dissolution and subsequent reaction of NaCl particles cause the attack of NdFeB.The corrosion presented three representative types:if the electrolyte covered magnetic phase and Nd-rich phase,the Nd-rich phase was corroded firstly due to galvanic effect;if the electrolyte covered magnetic phase,magnetic phase was corroded along the grain boundary;if the electrolyte located near the position of defects,corrosion progressed along with the defect because of low concentration of oxygen inside the defect.With corrosion progressing,local corrosion areas were mutually connected,with Nd-rich phase and grain boundary being …
Photoelectrochemical Properties Of N, S, And Cl Modified Nano Tio2 Thin Films,
2010
Key Laboratory of Shanghai Colleges and Universities for Electric Power Corrosion Control and Applied Electrochemistry,Department of Energy Source and Environment Engineering,Shanghai University of Electric Power,Shanghai 200090,China;State Key Laboratory for Physical Chemistry of Solid Surface,College of Chemistry and Chemical Engineering,Xiamen University,Xiamen 361005,Fujian,China;
Photoelectrochemical Properties Of N, S, And Cl Modified Nano Tio2 Thin Films, Hong Yun, Chang-Jian Lin, Jing Li, Rong-Gui Du
Journal of Electrochemistry
The nitrogen(N),sulfur(S) and chlorine(Cl) modified nano TiO2 thin films were prepared by adding Ti(O-n-Bu)4 as the precursor into concentrated HNO3,H2SO4 and HCl Solutions,respectively,on different substrates in a sol-gel process.The photoelectrochemical performances of N,S and Cl modified nano TiO2 thin films have been studied by UV-vis(DRS),photocurrent curves,EIS and OCP-time curves.N-modified TiO2 nano films show better surface structure,which helps to improve the quantum efficiency of nano TiO2 thin films.
Hydrothermal Reduction Synthesis Of Lifepo4 And Its Electrochemical Performance,
2010
The State Key Laboratory of Optoelectronic Materials and Technologies,School of Physics and Engineering,Sun Yat-Sen University,Guangzhou 510275,China;
Hydrothermal Reduction Synthesis Of Lifepo4 And Its Electrochemical Performance, Hong-Li Zou, Guang-Hui Zhang, Pei-Kang Shen
Journal of Electrochemistry
The cathode materials of LiFePO4 were prepared via a hydrothermal reduction method using FeCl3 as Fe source and iron as a reducing agent.The results showed that ferric salt could be reduced to ferrous salt completely under the hydrothermal condition and pure-phase LiFePO4 was obtained based on the test results of XRD and FTIR.Carbon-coated LiFePO4 was synthesized by pyrolysisng glucose at high temperature.The morphologies of pure LiFePO4 displayed cluster-like while the LiFePO4/C displayed sphere-like particles.The electrochemical test showed that the LiFePO4/C had good rate performance,while LiFePO4 delivered much lower discharge capacity.
Effects Of Solvents And Electrolyte Salts On The Electrochemical Reduction Of Oxygen In Non-Aqueous Electrolytes,
2010
State Key Laboratory for Physical Chemistry of Solid Surfaces and Department of Chemistry,College of Chemistry and Chemical Engineering,Xiamen University,Xiamen 361005,Fujian,China;
Effects Of Solvents And Electrolyte Salts On The Electrochemical Reduction Of Oxygen In Non-Aqueous Electrolytes, Yan-Yan Tian, Wei Wu, Jun Gao, Yong Yang
Journal of Electrochemistry
The electrochemical reduction processes of oxygen in different non-aqueous solvents such as acetonitrile(MeCN),propylene carbonate(PC) and their mixtures were investigated by cyclic voltammetry method.The results indicated a one electron reduction of oxygen to O2-occured in these systems as a first step reduction,no matter whether in tetrabutylammonium hexafluorophosphate(TBAPF6)/MeCN or TBAPF6/PC electrolyte.However,the CV curves in 0.1 mol·L-1 TBAPF6/MeCN showed a couple of reversible redox peaks,indicating that the reduction process of oxygen was irreversible in the 0.1 mol·L-1 TBAPF6/PC electrolyte.In the PC-based electrolyte,the reduction current peak reduced largely and the oxidation peak …
Corrosion Electrochemical Behavior Of Am60 Magnesium Alloys In Automobile Engine Coolants,
2010
College of Chemistry and Chemical Engineering,Chongqing University,Chongqing 400044,China;
Corrosion Electrochemical Behavior Of Am60 Magnesium Alloys In Automobile Engine Coolants, Ling-Jie Li, Sha Wang, Yin Xiao, Jun Lan, Jing-Lei Lei, Sheng-Tao Zhang, Fu-Sheng Pan
Journal of Electrochemistry
The polarization measurements and electrochemical impedance spectroscopy(EIS) were used to study the corrosion electrochemical behavior of AM60 magnesium alloys in three kinds of commercial coolants for automobile engine.Results show that the tested commercial coolants are slightly corrosive to AM60 magnesium alloys and their corrosivity varies from coolant to coolant.The coolant C is the least corrosive among the studied commercial coolants and the coolant A is more corrosive than the coolant B and C.The coolant C appears to be the most promising coolant for automobile engine made by magnesium alloys.The coolant resistivity plays an important role in the corrosion of AM60 …
