Materials Chemistry Commons^™

Towards One Key To One Lock: Catalyst Modified Indium Oxide Nanoparticle Thin Film Sensor Array For Selective Gas Detection, Kun Yao, Daniela Caruntu, Sarah Wozny, Rong Huang, Yumi H. Ikuhara, Baobao Cao, Charles J. O'Connor, Weilie Zhou

Advanced Materials Research Institute (AMRI)

Homogeneous In2O3 nanoparticles (NPs) were self-assembled into thin film sensor arrays on a single chip, with further surface modification by noble metal catalysts. The NP film sensor arrays show clear current responses when exposed to different target gases, and both sensitivity and selectivity were greatly improved. Particularly, the sensors modified with Au, Pd, and Pt nanocatalysts demonstrated higher sensitivity to H2S, H-2 and CO, respectively, making the gas discrimination direct and simple, like "one key to one lock". The particle size dependence of the noble metal modifiers to the sensitivity was further investigated by tuning the sputtering parameters. Three different …

Preparation And Characterization Of Mno/Tin Anode For Lithium Ion Batteries, Gao-Jie Xu, Hai-Yan Yang, Peng-Xian Han, Li-Xue Zhang, Ke-Jun Zhang, Chuan-Jian Zhang, Yu-Hua Fan, Cai-Feng Bi, Guang-Lei Cui

Journal of Electrochemistry

Manganese titanate (MnTiO₃) powder was prepared via a sol-gel method using manganese acetate and tetrabutyl titanate as raw materials, and citric acid as a chelating agent. Through high temperature nitridation of MnTiO₃ powder in ammonia, the MnO/TiN composite was obtained. The phase structure, composition and morphology of the composites were characterized by XRD, SEM and EDS. The electrochemical properties of the composite electrodes were studied by performing cyclic voltammetry, galvanostatic charge and discharge, and electrochemical impedance spectroscopy tests. The MnO/TiN electrode delivered specific capacities of 394 mAh·g^-1 and 146 mAh·g^-1 at the current density of …

The Electrocatalytic Study Of Licoo2 In Air Electrode For Lithium-Air, Jun Gao, Wei Wu, Yan-Yan Tian, Yong Yang

Journal of Electrochemistry

The LiCoO₂ has been investigated as a new electrocatalyst for air electrodes using homemade lithium-air battery. The electrochemical performance and structural changes of the LiCoO₂ based composite air electrodes have been studied. The results of CV, XRD and charge-discharge tests show that the composite air electrodes composed of LiCoO₂ can greatly improve the discharge performance of lithium-air batteries. In particular when the composite air electrodes are charged to 4.1 V before further discharging, the obvious catalytic effects of LiCoO₂ are attributed to higher valence state of the Co element in LiCoO₂, esp. at charged …

Progress And Perspective Of Fuel Cell Technology, Ming Hou, Bao-Lian Yi

Journal of Electrochemistry

Fuel cell, a clean and high-efficiency electrochemical power source, has being paid much attention worldwide recent years. In this paper, the progress and perspective of fuel cell technology are elucidated in detail. Fuel cells have been applied in some special fields such as spacecraft, shuttle and submarines. However, in the areas of transportation, stationary station and portable power source, fuel cells are still under demonstration due to the durability and cost problems. The reliability and surrounding survivability of fuel cells should be enhanced in the special application. Meanwhile, the durability and cost of fuel cells are the main issues to …

Preparation And Electrochemical Performance Of Lifepo4/C By Spray Drying Method Assisted With Organic Template, Quan-Bing Liu, Yang-Mei Jiang, Hui-Yu Song, Shi-Jun Liao

Journal of Electrochemistry

In this work, the LiFePO₄/C composites were prepared by the spray drying and carbothermal method, and were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and galvanostatic charge-discharge measurements. The effects of the organic assisted templates on the morphologies and electrochemical properties of the LiFePO₄/C composites were investigated. The results showed that the morphology and microstructure of the composites could be tuned by incorporating with the different templates. The morphology of the composite appeared to be solid microspheres if no organic template was added, while porous microspheres, nest-like …

Dissolved Oxygen Seawater Battery With Electrochemical Capacitance, Hai-Bo Xu, Yong-Hong Lu, Wei Zhang, Yan-Ting Yu, Chuan-Wei Yan, Ya-Ping Sun, Lian Zhong, Jian-Guo Liu, Yi Zheng, Bing Han, Yong-Liang Wang

Journal of Electrochemistry

A new concept of seawater battery with electrochemical capacitance (SWB-EC) has been proposed using carbon fibre brush (CFB) as the cathode material, and three testing prototypes have been made accordingly. The discharge performances of the CFB before- and after-oxidation and Mg alloy sacrifice anode were studied by cyclic voltammetry and constant current discharge tests under steady state conditions. Results show that the oxidized CFB exhibits the pseudo-capacitive characteristic and its activity of oxygen reduction reaction (ORR) in stirred seawater highly increases, comparing with the non-oxidized CFB. The open circuit potential of Mg alloy sacrifice anode is -1.74 V, having the …

Simultaneous Determinations Of Ascorbic Acid, Dopamine And Uric Acid At Ca/Gc Electrode, Ying Zhang, Wang Ren, Min-Jiao Li

Journal of Electrochemistry

The citric acid modified glassy carbon electrode (CA/GC) was constructed by potentiostatic technique and used for simultaneous determinations of ascorbic acid (AA), dopamine (DA) and uric acid (UA) by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The CA/GC electrode exhibits excellent electrocatalytic activity towards AA, DA and UA. The oxidation peaks are well separated with the potential differences between AA and DA, DA and UA, and AA and UA being 170, 130 and 300 mV, respectively, which is large enough to determine AA, DA and UA simultaneously. The catalytic peak currents obtained were linearly dependent on the concentrations of …

Electrocatalytic Study Of Pseudomonas Aeruginosa Bte-1 Strain, Ping Zhou, En-Ren Zhang, Li Zhou, Guo-Wang Diao, Jun-Le Niu

Journal of Electrochemistry

The aim of the present study is to investigate the electrocatalytic activity of electricity-producing Pseudomonas aeruginosa BTE-1 strain under anaerobic conditions. Pseudomonas aeruginosa BTE-1 was inoculated into anaerobic three-electrode electrochemical cells, and the electrocatalytic activity was measured at poised potentials. HPLC and cyclic voltammetry were used to detect potential electron mediators in solutions. Experimental results showed that no detectable pyocyanine was excreted by P. aeruginosa BTE-1 strain in the anaerobic electrochemcial cells, and P. aeruginosa BTE-1 exhibited direct electrocatalytic activity through the formation of biofilm on the electrode surface which was induced by the electron transfer from the cells of …

Ag Nanoparticles Self-Assembled Films On Iron Surface And Their Inhibition Properties, Zhe Zhang, Ming-Zi Jia, Le Ruan

Journal of Electrochemistry

The Ag nanoparticles were prepared in aqueous solutions through a chemical reduction method and transferred from water phase to toluene phase with the protection of 1-dodecanethiol (DDT). The polished iron electrode was immersed in the DDT-protected metal nanoparticles toluene solutions to form DDT/Ag nanoparticles self-assembled mixed films. Electrochemical methods such as electrochemical impedance spectroscopy and polarization curve measurement were used to study the inhibition properties of the self-assembled films in the 0.5 mol·L^-1 H₂SO₄ solution. The appearance of elements such as S and Ag from the XPS data identified the presences of DDT and Ag nanoparticles.

Synthesis And Electrochemical Performance Of Xlifepo4·Yli3V2(Po4)3 Composites, Ping-Ping Ma, Zhi-Jian Liu, Jian-Hua Xia, Yu Chen, Pu Hu, Zhi-Chao Lu, Ding-Guo Xia

Journal of Electrochemistry

A series of xLiFePO₄·yLi₃V₂(PO₄)₃ composites were systematically synthesized through solid state reactions by variations in the proportions of LiFePO₄ and Li₃V₂(PO₄)₃. The properties of the prepared compounds were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical measurements. The capacity of 162.7 mAh/g at 0.2 C rate was obtained with the relatively good cycle stability and good conductivity for 0.95LiFePO₄·0.05Li₃V₂(PO₄)₃ due to more uniformed distributed and smaller particle sizes.

Preparation And Hydrogen Evolution Properties Of Ni/Ag2O/Ruo2-Pt Cathodes, Shu Huang, Xue-Ming Li, Wu-Lin Li, Wen Wang

Journal of Electrochemistry

The Ni/Ag₂O/RuO₂-Pt composite cathode was prepared by sol-gel method using RuCl₃ and H₂PtCl₆ as raw materials. The effects of heat treatment conditions and AgNO₃ concentrations on hydrogen evolution properties were investigated. The morphology and composition of Ni/Ag₂O/RuO₂-Pt composite cathode have been characterized by XRD, XPS and SEM-EDS. It is demonstrated that the surface structure of Ni/Ag₂O/RuO₂-Pt composite cathode is more compact, with fewer cracks and larger surface roughness than pure nickel. At the conditions of 0.3 A·cm^-2, 90 ^oC, and …

Electrochemical Characterization Of (Phmgcl)2-Alcl3/Mixed Ether Electrolytes, Fei-Fei Wang, Yong-Sheng Guo, Jun Yang, Li-Yan-Na Nu, Jiu-Lin Wang

Journal of Electrochemistry

The (PhMgCl)₂-AlCl₃ salts were prepared and the electrochemical properties of (PhMgCl)₂-AlCl₃ electrolytes containing dimethoxyethane(DME)+THF, Diglyme(DG)+THF and Tetraglyme(TG)+THF solvents with different proportions on various metal electrodes were studied. Compared with (PhMgCl)₂-AlCl₃/THF, the (PhMgCl)₂-AlCl₃/DG+THF(3:2) solvents showed high ionic conductivity of 1.605×10^-3 S·cm^-1, good reversible Mg deposition behavior and anodic anti-oxidation performance with an electrochemical window wider than 2.8 V. In addition, the DG+THF mixed solvent could greatly lower the saturated vapor pressure by reducing from 23.46 kPa to 9.41 kPa, which suppresses volatilization of the …

Cycle Lifetime Investigation Of Nickel Electrode Prepared By Electrochemical Impregnation For Applications In Aerospace Nickel Hydrogen Cells, Hai-Chang Zhang, Li-Xin Tan, Cheng Guo, Wen-Cheng Ming, Xue-Ying Ren

Journal of Electrochemistry

In this paper, the effects of overcharge, charge-discharge C rate and pore size on cycle lifetime of 4.5’ electrochemical impregnated nickel electrode were investigated. In the case of the electrode was overcharged to 170% of nominal capacity, the initial capacity of the electrode could be maintained 2.7 Ah up to 150 cycles without deterioration and a discharge capacity of 1.7 Ah (remaining 63% of 2.7 Ah) could be delivered after 300 cycles. Without overcharge, more than 300 charge-discharge cycles could be realized without loss of capacity and a discharge capacity of electrode could be maintained about 76% of initial capacity …

Preparation And Rapid Analysis Of Antibacterial Silver, Copper And Zinc Doped Sol–Gel Surfaces, Brendan Duffy, Swarna Jaiswal, Patrick Mchale

Articles

The colonisation of clinical and industrial surfaces with microorganisms, including antibiotic-resistant strains, has promoted increased research into the development of effective antibacterial and antifouling coatings. This study describes the preparation of metal nitrate (Ag, Cu, Zn) doped methyltriethoxysilane (MTEOS) coatings and the rapid assessment of their antibacterial activity using polyproylene microtitre plates. Microtitre plate wells were coated with different volumes of liquid sol–gel and cured under various conditions. Curing parameters were analysed by thermogravimetric analysis (TGA) and visual examination. The optimum curing conditions were determined to be 50–70C using a volume of 200ul. The coated wells were challenged with Gram-positive …

Optimization Of Magnetic Powdered Activated Carbon For Aqueous Hg(Ii) Removal And Magnetic Recovery, Emily K. Faulconer, Natalia Hoogesteijn Von Reitzenstein, David W. Mazyck

Physical Sciences - Daytona Beach

Activated carbon is known to adsorb aqueous Hg(II). MPAC (magnetic powdered activated carbon) has the potential to remove aqueous Hg to less than 0.2 mg/L while being magnetically recoverable. Magnetic recapture allows simple sorbent separation from the waste stream while an isolated waste potentially allows for mercury recycling. MPAC Hg-removal performance is verified by mercury mass balance, calculated by quantifying adsorbed, volatilized, and residual aqueous mercury. The batch reactor contained a sealed mercury-carbon contact chamber with mixing and constant N₂(g) headspace flow to an oxidizingtrap. Mercury adsorption was performed using spiked ultrapure water (100 mg/L Hg). Mercury concentrations …

One-Pot Synthesis In Polyamines For Preparation Of Water-Soluble Magnetite Nanoparticles With Amine Surface Reactivity, Haiou Qu, Hui Ma, Aurélien Riviere, Weilie Zhou, Charles J. O'Connor

Chemistry Faculty Publications

Magnetite nanoparticles with hydrophilic surface coating are prepared in polyamine solvents. The resulting products are highly stable in polar solvent. The surface amine groups are available for secondary reactions.

Existence Of A Minimizer For The Quasi-Relativistic Kohn-Sham Model, Carlos Argáez García, Michael Melgaard

Articles

We study the standard and extended Kohn-Sham models for quasi-relativistic N-electron Coulomb systems; that is, systems where the kinetic energy of the electrons is given by the quasi-relativistic operator (see article) . For spin-unpolarized systems in the local density approximation, we prove existence of a ground state (or minimizer) provided that the total charge Z of K nuclei is greater than N-1 and that Z is smaller than a critical charge (see article).

Horizontally-Aligned Carbon Nanotubes Arrays And Their Interactions With Liquid Crystal Molecules: Physical Characteristics And Display Applications, Frederick Roussel, Jean-Francois Brun, Alexandre Allart, Limin Huang, Stephen O'Brien

Publications and Research

We report on the physical characteristics of horizonthally-grown Single-Walled Carbon Nanotubes (h-al-SWNT) arrays and their potential use as transparent and conducting alignment layer for liquid crystals display devices. Microscopy (SEM and AFM), spectroscopic (Raman) and electrical investigations demonstrate the strong anisotropy of h-al-SWNT arrays. Optical measurements show that h-al-SWNTs are efficient alignment layers for Liquid Crystal (LC) molecules allowing the fabrication of optical wave plates. Interactions between h-al-SWNT arrays and LC molecules are also investigated evidencing the weak azimuthal anchoring energy at the interface, which, in turn, leads to LC devices with a high pretilt angle. The electro-optical reponses of …

Chiral Magnetization Configurations In Magnetic Nanostructures In The Presence Of Dzyaloshinski-Moriya Interactions, Naoise Grisewood, John Eves, Timothy Usher, Hans-Benjamin Braun

Physics Faculty Publications

Many low-dimensional systems, such as nanoscale islands, thin films, and multilayers, as well as bulk systems, such as multiferroics, are characterized by the lack of inversion symmetry, a fact that may give rise to a Dzyaloshinskii-Moriya (DM) interaction. For sufficient strength, the DM interaction will favor spiral spin configurations of definite chirality. In order to harness such systems for applications, it is important to understand the conditions under which these spiral spin configurations form and how they can be controlled via an external field. Here, we present exact solutions of the 1D magnetization profiles in such systems for arbitrary material …

Ƴ-Selective Directed Catalytic Asymmetric Hydroboration Of 1,1-Disubstituted Alkenes, Sean M Smith, Gia L. Hoang, Rhitankar Pal, Mohammad O. Bani Khaled, Liberty S. W. Pelter, Xiao Cheng Zeng, James M. Takacs

Xiao Cheng Zeng Publications

Directed catalytic asymmetric hydroborations of 1,1-disubstituted alkenes afford ƴ

-dioxaborato amides and esters in high enantiomeric purity (90–95% ee).