Nanoscience and Nanotechnology Commons^™

Vibrating Flexoelectric Micro-Beams As Angular Rate Sensors, Yilin Qu, Feng Jin, Jiashi S. Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We studied flexoelectrically excited/detected bending vibrations in perpendicular directions of a micro-beam spinning about its axis. A set of one-dimensional equations was derived and used in a theoretical analysis. It is shown that the Coriolis effect associated with the spin produces an electrical output proportional to the angular rate of the spin when it is small. Thus, the beam can be used as a gyroscope for angular rate sensing. Compared to conventional piezoelectric beam gyroscopes, the flexoelectric beam proposed and analyzed has a simpler structure.

Geometric Analysis Of Insect Wing Vein Network, Jacob White, Ying Hu, Sangjin Ryu, Seunghee Kim, Haipeng Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

An insect wing consists of a thin membrane supported by a system of veins, and flow of blood through the system of veins is critical for maintaining healthy insect wings. Better understanding of the insect wing vein circulation requires to know how the efficiency of blood flow in an insect wing relates to the geometric shape of the vein. Our investigation of the wing vein network of a dragonfly Anax junius follows the idea of Murray’s law, which is established in the study of efficiency of the vein network and the geometric shape of the vein. Instead of using the …

Biological Interaction Of Mn-Based Nanomaterials With Capsicum Annuum L. Under Salinity Stress, Yuqing Ye

Open Access Theses & Dissertations

The foliar application of nanomaterials as a method to overcome abiotic stress is relatively new compared to their use as fertilizers or pesticides in agricultural practice. It is also vital to understand the interface between leaf and nanomaterials, as nanomaterials might translocate into crop edible tissues, thus, causing potential toxicity in living beings during food consumption. In this dissertation, salt-stressed Capsicum annuum L was exposed to manganese (Mn) -based nanomaterials (Mn2O3 nanoparticles (MnNPs) and graphene quantum dots doped with Mn (GQD-Mn)) at different stages (seed germination and full life cycle). The dissertation focuses on investigating the mechanism of how Mn-based …

Variations In Copper Form Exposure Differentially Modulate Zea Mays (Corn) Physiological Responses, Carolina Valdes Bracamontes

Open Access Theses & Dissertations

In the present study, Zea mays seedlings grown under nano Cu(OH)2 (nCu), bulk Cu(OH)2 (bCu), and ionic CuSO4 (iCu) compound exposure were harvested after six days. The nutritional profile was determined to be significantly disrupted in the roots by 1000 ppm bCu treatment, resulting in a 58.7% reduction in potassium compared to the control. In the shoots, a significant decrease of manganese was observed for 10 and 1000 ppm iCu treatments with 55.7% and 64.2% reductions, respectively. The overall protein content and catalase (CAT) enzymatic activity, however, remained unaffected in either roots or shoots, while an absence of polyphenol oxidase …

Subwavelength Engineering Of Silicon Photonic Waveguides, Farhan Bin Tarik

All Dissertations

The dissertation demonstrates subwavelength engineering of silicon photonic waveguides in the form of two different structures or avenues: (i) a novel ultra-low mode area v-groove waveguide to enhance light-matter interaction; and (ii) a nanoscale sidewall crystalline grating performed as physical unclonable function to achieve hardware and information security. With the advancement of modern technology and modern supply chain throughout the globe, silicon photonics is set to lead the global semiconductor foundries, thanks to its abundance in nature and a mature and well-established industry. Since, the silicon waveguide is the heart of silicon photonics, it can be considered as the core …

Control Mechanisms For Adaptive Nanoscale Devices, David Arredondo

Nanoscience and Microsystems ETDs

Nanotechnology promises to revolutionize many areas of applied science including materials, synthetic biology, and medicine. Devices may consist of solution-phase information processing systems or molecular robots. Of particular interest are DNA-based systems due to their composability and relatively simple interactions that are suited to bottom-up design. This work introduces high-level designs of robust control mechanisms for nanoscale devices with immediate applications in molecular computing, synthetic biology, and DNA robotics.

Nanoscale systems are dominated by probabilistic chemical behavior, so engineers must take careful consideration to produce predictable systems. Probabilistic behavior in chemical reaction networks (CRNs) yields deterministic evolution of species concentrations …

Understanding The Role Of Antioxidant Nanoparticles In Improving The Outcome Of Secondary Injury In Traumatic Brain Injury, Aria W. Tarudji

Department of Agricultural and Biological Systems Engineering: Dissertations, Theses, and Student Research

Following traumatic brain injury (TBI), excess reactive oxygen species (ROS) and other free radicals are released, inducing the cascade of secondary injury that exacerbate the outcomes of TBI. Antioxidant nanoparticles (ANPs) have shown promising outcomes in reducing the progression of TBI, which may be due to the higher accumulation and retention of ANPs in the injured brain. However, there is limited knowledge of: 1) antioxidant activities needed in TBI treatment, 2) correlation between longer retention, bioavailability, and target engagement with antioxidant treatments, and 3) sexual dimorphism to ANP treatments.

This dissertation assesses multiple ANPs with various scavenging activities and durations …

Mechanism And Application Of Nickel Nano-Cone By Electrodeposition On A Flexible Substrate, Xiu-Ren Ni, Ya-Ting Zhang, Chong Wang, Yan Hong, Yuan-Ming Chen, Yuan-Zhang Su, Wei He, Xian-Ming Chen, Ben-Xia Huang, Zhen-Lin Xu, Yi-Feng Li, Neng-Bin Li, Yong-Jie Du

Journal of Electrochemistry

Nano-array structure possesses promising prospect in power supply, optical device and electronic manufacturing. In this paper, a black nickel nano-cone array was prepared on a flexible substrate by galvanostatic deposition and the corresponding factors involved in the fabrication of nickel nano-cone array was explored. Experimental results showed that a large current density and low main salt concentration were not favored to the formation of cone nickel structure. It was also found that ammonium chloride, as the crystal modifier, was crucial to deposit the uniform nano-cone array. In addition, the growth mechanism of nickel nano-cone was further studied by molecular dynamics …

Cyberpunk As An Evolution From Science-Fiction And Its Social Critiques, William C. Svihla

University Honors Program

In this paper, I will take an investigative deep dive into all that is the literary genre of cyberpunk. I will touch on the origins and development of science-fiction, the genre that birthed cyberpunk, and how science-fiction led up to cyberpunk’s birth. I discuss the origins of cyberpunk and where and when it first entered the scene. The literary differences between the two genres. And the main areas of social critique that are focused on for each as well. For science-fiction’s areas of social critique, I discuss their ever-present use of the dangers of man’s hubris first made present in …

The Effects Of Curing Temperature On The Hydration Kinetics Of Plain And Fly Ash Pastes And Compressive Strength Of Corresponding Mortars With And Without Nano-Tio2 Addition., Dan Huang, Mirian Velay-Lizancos, Jan Olek

International Conference on Durability of Concrete Structures

Incorporation of fly ash in cementitious systems containing ordinary portland cement (OPC) increases their long-term strength and durability. However, replacement of cement by fly ash also reduces the heat of hydration of such systems and reduces early-age strength development. The reduced rate of strength development can increase the risk of durability problems, e.g. scaling, in cases when young concrete is exposed to low temperatures and deicing chemicals. This study investigated the potential of nano-titanium dioxide (nano-TiO₂) particles to modify the hydration kinetics of fly ash pastes and compressive strength development of corresponding mortars cured under low (4°C) and …

Physiologically-Based Pharmacokinetics Modeling Of Colloidal Nanoparticles, Anh-Dung Le

Nanoscience and Microsystems ETDs

Physiologically-based Pharmacokinetics (PBPK) modeling—a mechanistic mathematical tool to predict biodistribution to inform drug development, requires knowledge of the physico-chemical properties of the drug in question as well as the anatomy and physiology of the organism. Unlike with molecular drugs, nanoparticle parameters often need to be estimated by fitting models to time-course data, which can result in large uncertainties in parameter estimates due to a high-dimensional parameter space. Our research addresses this challenge by offering a path to parameter insights using global sensitivity analysis. The first chapter is an overview of the PBPK model structure and mathematical framework used in our …

Fabrication And Characterization Of Carbon Nanotube Metal Matrix Composites For Use In Photovoltaic Gridline Applications, Cayla M. Nelson

Nanoscience and Microsystems ETDs

Performance reliability is crucial for photovoltaic (PV) cells in both terrestrial and space-based applications. Electrical efficiency losses over time are heavily impacted by electrical losses due to microcracks within the cell structure and metallization failure. Mechanical stresses and thermal cycling of the device can lead to fracture of the current-carrying metal (Ag) lines on the surface of the device, significantly reducing output power. Incorporating carbon nanotubes (CNTs) into PV metal lines as a reinforcement, forming a CNT/Ag metal matrix composite (MMC), enhances the electrical and mechanical performance of the device. In this work the influence of CNT/Ag MMCs were explored …

Reducing Leakage Current And Enhancing Polarization In Multiferroic 3d Super-Nanocomposites By Microstructure Engineering, Erik Enriquez, Ping Lu, Leigang Li, Bruce Zhang, Haiyan Wang, Quanxi Jia, Aiping Chen

Physics & Astronomy Faculty Publications

Multiferroic materials have generated great interest due to their potential as functional device materials. Nanocomposites have been increasingly used to design and generate new functionalities by pairing dissimilar ferroic materials, though the combination often introduces new complexity and challenges unforeseeable in single-phase counterparts. The recently developed approaches to fabricate 3D super-nanocomposites (3D‐sNC) open new avenues to control and enhance functional properties. In this work, we develop a new 3D‐sNC with CoFe2O4 (CFO) short nanopillar arrays embedded in BaTiO3 (BTO) film matrix via microstructure engineering by alternatively depositing BTO:CFO vertically-aligned nanocomposite layers and single-phase BTO layers. This microstructure engineering method allows …

Octopus-Inspired Adhesive Skins For Intelligent And Rapidly Switchable Underwater Adhesion, Sean T. Frey, A. B. M. Tahidul Haque, Ravi Tutika, Elizabeth V. Krotz, Chanhong Lee, Cole B. Haverkamp, Eric J. Markvicka, Michael D. Bartlett

Department of Mechanical and Materials Engineering: Faculty Publications

The octopus couples controllable adhesives with intricately embedded sensing, processing, and control to manipulate underwater objects. Current synthetic adhesive–based manipulators are typically manually operated without sensing or control and can be slow to activate and release adhesion, which limits system-level manipulation. Here, we couple switchable, octopus-inspired adhesives with embedded sensing, processing, and control for robust underwater manipulation. Adhesion strength is switched over 450× from the ON to OFF state in <50 ms over many cycles with an actively controlled membrane. Systematic design of adhesive geometry enables adherence to nonideal surfaces with low preload and independent control of adhesive strength and adhesive toughness for strong and reliable attachment and easy release. Our bio-inspired nervous system detects objects and autonomously triggers the switchable adhesives. This is implemented into a wearable glove where an array of adhesives and sensors creates a biomimetic adhesive skin to manipulate diverse underwater objects.

A Pilot Study On The Nanoscale Properties Of Bone Tissue Near Lacunae In Fracturing Women, Wen Qian, Roman Schmidt, Joseph A. Turner, Sue P. Bare, Joan M. Lappe, Robert R. Recker, Mohammed P. Akhter

Department of Mechanical and Materials Engineering: Faculty Publications

The goal of this study is to investigate the causes of osteoporosis-related skeletal fragility in postmenopausal women. We hypothesize that bone fragility in these individuals is largely due to mineral, and/or intrinsic material properties in the osteocyte lacunar/peri-lacunar regions of bone tissue. Innovative measurements with nanoscale resolution, including scanning electron microscope (SEM), an atomic force microscope that is integrated with infrared spectroscopy (AFM-IR), and nanoindentation, were used to characterize osteocyte lacunar and peri-lacunar properties in bone biopsies from fracturing (Cases) and matched (Age, BMD), non-fracturing (Controls) postmenopausal healthy women. In the peri-lacunar space, the nanoindentation results show that the modulus …

Surface-Wave Coupling In Double Floquet Sheets Supporting Phased Temporal Wood Anomalies, Ya-Wen Tsai, Yao-Ting Wang, Emanuele Galiffi, Andrea Alù, Ta-Jen Yen

Advanced Science Research Center

We investigate symmetry-selective surface-mode excitation in a general periodically time-modulated double-layer system, where the modulation of the two layers has a constant phase difference. By deriving a semi-analytic transfer matrix formalism of a Drude-dispersive double-layer structure with periodic time-modulation, we calculate the scattering amplitudes and the corresponding transmission coefficient. Our results show that the phase-difference between the modulation of the two sheets plays an essential role in significantly enhancing and selectively exciting either the even or odd surface mode with high efficiency. We verify our calculations with full-wave time-domain simulations, showing that efficient switching between the surface-wave excitation of the …

Characterization Of Electrophoretic Deposited Zinc Oxide Nanopartices For The Fabrication Of Next-Generation Nanoscale Electronic Applications, Fawwaz Abduh A. Hazzazi

LSU Doctoral Dissertations

Several reports state that it is crucial to analyze nanoscale semiconductor materials and devices with potential benefits to meet the need for next-generation nanoelectronics, bio, and nanosensors. The progress in the electronics field is as significant now, with modern technology constantly evolving and a greater focus on more efficient robust optoelectronic applications. This dissertation focuses on the study and examination of the practicality of Electrophoretic Deposition (EPD) of zinc oxide (ZnO) nanoparticles (NPs) for use in semiconductor applications.

The feasibility of several synthesized electrolytes, with and without surfactants and APTES surface functionalization, is discussed. The primary objective of this study …

Microfluidic Device For Localized Electroporation, Justin Brooks, Arian Jaberi, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Electroporation is a common method of transfection due to its relatively low risk and high transfection efficiency. The most common method of electroporation is bulk electroporation which is easily performed on large quantities of cells yet results in variable levels of viability and transfection efficiency across the population. Localized electroporation is an alternative that can be administered on a similar scale but results in much more consistent with higher quality transfection and higher cell viability. This paper discusses the creation and use of a simple and cost-effective device using porous membrane for performing localized electroporation.

Phase Space Analysis Of Nonlinear Wave Propagation In A Bistable Mechanical Metamaterial With A Defect, Mohammed A. Mohammed, Piyush Grover

Department of Mechanical and Materials Engineering: Faculty Publications

We study the dynamics of solitary waves traveling in a one-dimensional chain of bistable elements in the presence of a local inhomogeneity (`defect'). Numerical simulations reveal that depending upon its initial speed, an incoming solitary wave can get transmitted, captured or reflected upon interaction with the defect. The dynamics are dominated by energy exchange between the wave and a breather mode localized at the defect. We derive a reduced-order two degree of freedom Hamiltonian model for wave-breather interaction, and analyze it using dynamical systems techniques. Lobe dynamics analysis reveals the fine structure of phase space that leads to the complicated …

Passive Radiative Cooling By Spectrally Selective Nanoparticles In Thick Film Nanocomposites, David Allen Young

USF Tampa Graduate Theses and Dissertations

Passive cooling of buildings is a benefit to society since no energy input is required for space cooling which reduces electricity consumption, fossil fuel burning, and greenhouse gas emissions. When a passive cooling technology radiates heat from the earth through the atmospheric windows to space higher levels of cooling power are possible -- this phenomenon is classified as passive “radiative” cooling. Spectrally selective surface coatings provide radiative cooling to lower surface temperatures by reflecting most solar radiation, while emitting infrared radiation at wavelengths between 8-13 μm through the primary atmospheric window to the cold of space. Multiple applications of radiative …

An Investigation On The Interface Corrosion Behaviors Of Cobalt Interconnects In Chemical Mechanical Polishing Slurry, Kai-Xuan Qin, Peng-Fei Chang, Yu-Lin Huang, Ming Li, Tao Hang

Journal of Electrochemistry

Cobalt is widely regarded as the most promising interconnect material for 10 nm node and beyond. The development of a chemical mechanical planarization (CMP) slurry suitable for cobalt interconnect is a critical component for the application of cobalt interconnect. During CMP process of the interconnect layer, the achievement of high-quality surface after planarization is greatly challenged by the metal corrosion in CMP slurry. In this contribution, the corrosion behavior of cobalt in a slurry with potassium persulfate (KPS) as an oxidizer, glycine as a complexing agent, and benzotriazole (BTA) as an inhibitor was investigated. Static erosion rates (SER) of cobalt …

Research Progresses Of Cobalt Interconnect And Superfilling By Electroplating In Chips, Li-Jun Wei, Zi-Han Zhou, Yun-Wen Wu, Ming Li, Su Wang

Journal of Electrochemistry

Copper interconnect using dual damascene technology has always been the main means for metallization in the back end of line process. However, with the size effect becoming more and more obvious due to feature size reduction, copper interconnect can no longer meet the demand for high circuit speed in Post-Moore era. Following copper interconnection, cobalt interconnection in chips attracts much attention as an interconnect technology by the next generation, which has been introduced in 7 nm node of integrated circuit manufacturing and below. The electron mean free path of cobalt (~10 nm) is much shorter than copper’s (39 nm), thus …

The Dark Annulus Of A Drop In A Hele-Shaw Cell Is Caused By The Refraction Of Light Through Its Meniscus, Sangjin Ryu, Haipeng Zhang, Carson Emeigh

Department of Mechanical and Materials Engineering: Faculty Publications

Knowing the meniscus shape of confined drops is important for understanding how they make first contact and then coalesce. When imaged from the top view by brightfield microscopy, a liquid drop (e.g., corn syrup) confined in a Hele-Shaw cell, surrounded by immiscible liquid (e.g., mineral oil), had a dark annulus, and the width of the annulus decreased with increasing concentration of corn syrup. Since the difference in the annulus width was presumed to be related to the meniscus shape of the drops, three-dimensional images of the drops with different concentrations were obtained using confocal fluorescence microscopy, and their cross-sectional meniscus …

Modular Cable - Driven Surgical Robots, Carl A. Nelson, Nicholas Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

A surgical robot can be configured for minimally invasive surgery ( MIS ) and other types of surgery with modular link geometry and disposable components. In some examples, the surgical robot includes a cable driver comprising at least one drive motor configured for tensioning a cable. The surgical robot includes an articulated surgical tool coupled to the drive motor by the cable. The articulated surgical tool comprises at least first and second articulated links and a joint coupling the first and second articulated links. The cable passes through the joint, and the joint comprises an elastic antagonist biased in opposition …

Biomimetic Strategies To Control Therapeutic Release From Novel Dna Nanoparticles, Robert J. Mosley

Theses and Dissertations

The inherent chemical, mechanical, and structural properties of nucleic acids make them ideal candidates for the formulation of tunable, personalized drug nanocarriers. However, none so far have exploited these properties for the controlled release of therapeutic drugs. In this dissertation, a biomimetic approach to controlling drug release is exhibited by specifically manipulating the architecture of novel, DNA nanoparticles to take advantage of drug binding mechanisms of action. Rationally designed DNA strands were immobilized on gold surfaces via a terminal thiol modification. Immobilized monomers can be manipulated to form distinct monolayer architectures including flat, folded, coiled, or stretched structures. Increasing the …

Gross Positioning Device And Related Systems And Methods, Mark A. Reichenbach, Shane M. Farritor

Department of Mechanical and Materials Engineering: Faculty Publications

Disclosed herein are gross positioning systems for use with robotic surgical devices to provide gross positioning of the robotic surgical devices. The gross positioning systems have a base, a first arm link operably coupled to the base, a second arm link operably coupled to the first arm link, a third arm link operably coupled to the second arm link, and a slidable coupling component slidably coupled to the third arm link.

Augmented Formic Acid Electro-Oxidation At A Co-Electrodeposited Pd/Au Nanoparticle Catalyst, Yaser M. Asal, Ahmad M. Mohammad, Sayed S. Abd El Rehim, Islam M. Al-Akraa

Chemical Engineering

In this study, the formic acid electro-oxidation reaction (FAEOR) was catalyzed on a Pd-Au co-electrodeposited binary catalyst. The kinetics of FAEOR were intensively impacted by changing the Pd2+:Au3+ molar ratio in the deposition medium. The Pd1-Au1 catalyst (for which the Pd2+:Au3+ molar ratio was 1:1) acquired the highest activity with a peak current density for the direct FAEOR (Ip) of 4.14 mA cm−2 (ca. 13- times higher than that (ca. 0.33 mA cm−2) of the pristine Pd1-Au0 catalyst). It also retained the highest stability that was denoted in fulfilling ca. 0.292 mA cm−2 (ca. 19-times higher than 0.015 …

Uv Space Imager Enclosure Coating, David Silva Cortez, Victor Alexander Rempel Dekhtyar, Maria L. Muñoz

Mechanical Engineering

The goal of this project is to reduce the amount of stray light entering an ultraviolet (UV) imager through absorption. This report outlines the use of ZnO nanoparticles mixed in an epoxy matrix for use in a CubeSat enclosure. Through testing, our team verified that the ZnO and epoxy coating experienced a peak absorption between 360-370 nm. The epoxy mixture with the .75% by weight ZnO nanoparticles absorbed up to 99.9 % of UV light at its peak. The effect on material properties, such as Young’s modulus and ultimate tensile strength, was also tested. Tensile tests demonstrated that adding ZnO …

A Python Implementation Of The Quasi-Harmonic Approximation: Ab-Initio Study Of The Thermoelastic Properties Of Magnesium Oxide And Calcium Oxide, Adewumi Bakare

Dissertations, Theses, and Capstone Projects

When heated up, materials change volume, typically they expand, and they also change their elastic properties, typically by softening. Computational methods to calculate materials properties at finite temperature are needed to compensate for the lack of experimental data, as well as to predict materials properties at conditions difficult to be reached in experimental labs. In this research project, I designed a set of Python codes implementing a quasi-harmonic approximation (QHA) method to calculate thermodynamic functions at constant volume, equation of state, and the isothermal Bulk modulus of cubic materials. To validate the new computational tools, this implementation of QHA has …

Observation And Control Of Photoemission And Electric Field Enhancement Of Plasmonic Antennas Through Photoemission Electron Microscopy, Christopher M. Scheffler

Dissertations and Theses

Photoemission electron microscopy (PEEM) is an imaging method which uses electrons excited through the photoelectric effect to characterize a sample surface with nanometer-level resolution. In PEEM, a high intensity laser excites electrons from the surface of the material and electron optics are used to form an image from the intensity and spatial distribution of the photoemission from the sample. The goal of this research was to study and maximize light confinement, which was accomplished using plasmonic nanostructures. Surface plasmons represent oscillations in the electron density of a material and can occur along the transition interface between a metal and a …