Nanoscience and Nanotechnology Commons^™

Electronic Communication Between Co And Ru Sites Decorated On Nitrogen-Doped Carbon Nanotubes Boost The Alkaline Hydrogen Evolution Reaction, Meng-Ting Gao, Ying Wei, Xue-Meng Hu, Wenj-Jie Zhu, Qing-Qing Liu, Jin-Yuan Qiang, Wan-Wan Liu, Ying Wang, Xu Li, Jian-Feng Huang, Yong-Qiang Feng

Journal of Electrochemistry

Designing highly efficient Pt-free electrocatalysts with low overpotential for an alkaline hydrogen evolution reaction (HER) remains a significant challenge. Here, a novel and efficient cobalt (Co), ruthenium (Ru) bimetallic electrocatalyst composed of CoRu nanoalloy decorated on the N-doped carbon nanotubes (CoRu@N-CNTs), was prepared by reacting fullerenol with melamine via hydrothermal treatment and followed by pyrolysis. Benefiting from the electronic communication between Co and Ru sites, the as-obtained CoRu@N-CNTs catalyst exhibited superior electrocatalytic HER activity. To deliver a current density of 10 mA·cm^–2, it required an overpotential of merely 19 mV along with a Tafel slope of 26.19 mV·dec …

Alternative Applications Of Composite Materials To Reduce Radar Cross Section, Mark Patterson

Mechanical & Aerospace Engineering Theses & Dissertations

The use of carbon nanoparticles and graphene in composite materials has created a foundational shift in enhancing performance across mechanical, thermal, and electrical properties. Such applications are vital in the aerospace industry. However, there has not been such a focus on the material use for reducing radar cross section (RCS). Historically, RCS is minimized by designing sharp geometric shapes to deflect or dissipate the incoming electromagnetic waves away from the receiving antenna. However, these designs are not always optimized for aerodynamics. The goal of this research is to understand the application of composite materials and specifically carbon nanotubes (CNTs) to …

Molybdenum Disulfide And Carbon Nanotubes Composite Electrode For Electrochemical Conversion Of Salinity Gradient Energy, Jia-Jun Li, Wei-Bin Zhang, Xin-Yu Liu, Jing-Lei Yang, Yi Yin, Ze-Qin Yang, Xue-Jing Ma

Journal of Electrochemistry

The ocean accounts for 97% of the total water resources on earth, covering over 70% of the map's surface area. With the continuous consumption of non-renewable energy sources such as fossil fuels and the rapid development of renewable energy, humans are increasingly paying attention to the utilization of ocean resources. Ocean energy includes tidal energy, wave energy, temperature difference energy, and salinity gradient energy. Salinity gradient energy is the energy generated by the interaction of seawater and fresh water, which is the ocean energy existing in the form of chemical energy. This energy is mostly generated in estuaries. The osmotic …

Development Of Super Hydrophobic Membranes And Their Applications, Sumona Paul

Dissertations

Effective liquid phase separation is vital across industries, especially in aviation, chemicals, fuels, and textiles. Membrane technology offers advantages over traditional methods like distillation, with low energy consumption and protection for heat-sensitive molecules. Membrane performance is assessed based on factors such as materials, surface modification, and interactions. This research targets superhydrophobic membranes for liquid-liquid filtration and antiwetting omniphobic membranes for membrane distillation, focusing on properties like contact angle and thermal resistance.

This study presents a highly hydrophobic membrane achieved by immobilizing carbon nanotubes (CNTs) onto a PTFE microfiltration membrane. It's designed for dewatering organic-water mixtures with trace water content via …

Development Of Novel Nanocarbon Based Materials And Membranes With Enhanced Biocidal Capabilities For Clean Water Generation, Indrani Gupta

Dissertations

Water scarcity is one of the major challenges facing humanity today, driven by population growth, economic development, and dietary shifts towards more water-intensive animal products. To address this issue, efficient water resource management and recycling of wastewater are essential. However, around 80% of wastewater globally is discharged into water bodies without treatment, posing a risk to ecosystems and human health. Pathogens, or harmful microorganisms, are a primary cause of water impairment and the transmission of waterborne diseases, leading to increased mortality rates. Traditional methods of treating pathogens involve the use of radiation or chemical disinfectants. Nonetheless, these methods have drawbacks, …

Mechanical Properties And Performance Of A Novel Nano-Engineered Unitized Composite With Quasi-Isotropic Layup, Brian Matthew Pudlo

Theses and Dissertations

Carbon nanotubes (CNTs) exhibit outstanding mechanical, electrical, and thermal properties, but are a challenge to effectively implement into macroscopic composites for aerospace applications. This research investigates the mechanical properties and performance of a newly developed hybrid NanoStitch composite, alongside a control polymer matrix composite, at room temperature. Both composite material systems investigated in this work have quasi-isotropic layup. Monotonic tension-tofailure, tension-tension fatigue, and creep tests were performed to characterize the performance of the composites under cyclic and sustained loading. Experimental results obtained for the quasi-isotropic NanoStitch composite were compared to those obtained for the quasi-isotropic control composite. The properties and …

Using Nanomaterials As Excellent Immobilisation Layer For Biosensor Design, Azeez Olayiwola Idris, Seyi Philemon Akanji, Benjamin O. Orimolade, Foluke Omobola Grace Olorundare, Shohreh Azizi, Bhekie Mamba, Malik Maaza

Research outputs 2022 to 2026

The endless development in nanotechnology has introduced new vitality in device fabrication including biosensor design for biomedical applications. With outstanding features like suitable biocompatibility, good electrical and thermal conductivity, wide surface area and catalytic activity, nanomaterials have been considered excellent and promising immobilisation candidates for the development of high-impact biosensors after they emerged. Owing to these reasons, the present review deals with the efficient use of nanomaterials as immobilisation candidates for biosensor fabrication. These include the implementation of carbon nanomaterials—graphene and its derivatives, carbon nanotubes, carbon nanoparticles, carbon nanodots—and MXenes, likewise their synergistic impact when merged with metal oxide nanomaterials. …

Fabrication And Characterization Of Carbon Nanotube Metal Matrix Composites For Use In Photovoltaic Gridline Applications, Cayla M. Nelson

Nanoscience and Microsystems ETDs

Performance reliability is crucial for photovoltaic (PV) cells in both terrestrial and space-based applications. Electrical efficiency losses over time are heavily impacted by electrical losses due to microcracks within the cell structure and metallization failure. Mechanical stresses and thermal cycling of the device can lead to fracture of the current-carrying metal (Ag) lines on the surface of the device, significantly reducing output power. Incorporating carbon nanotubes (CNTs) into PV metal lines as a reinforcement, forming a CNT/Ag metal matrix composite (MMC), enhances the electrical and mechanical performance of the device. In this work the influence of CNT/Ag MMCs were explored …

Molecular Modeling Of High-Performance Thermoset Polymer Matrix Composites For Aerospace Applications, Prathamesh P. Deshpande

Dissertations, Master's Theses and Master's Reports

The global efforts from major space agencies to transport humans to Mars will require a novel lightweight and ultra-high strength material for the spacecraft structure. Three decades of research with the carbon nanotubes (CNTs) have proved that the material can be an ideal candidate for the composite reinforcement if certain shortcomings are overcome. Also, the rapid development of the polymer resin industry has introduced a wide range of high-performance resins that show high compatibility with the graphitic surface of the CNTs. This research explores the computational design of these materials and evaluates their efficacy as the next generation of aerospace …

Controlled Reduction Of Graphene Oxide And Graphene Oxide-Carbon Nanotube Hybrids And Their Applications, Samar Azizighannad

Dissertations

Graphene and graphene derivatives are widely used in diverse research and industrial applications. Graphene production on a large scale is carried out by exfoliating graphite oxide and producing graphene oxide (GO), which comprises of graphene sheets with different oxygen-containing functional groups such as hydroxyl, carboxyl, and carbonyl. GO is reduced to reduced graphene oxide (rGO), which has properties that are closer to graphene. Properties of GO and rGO depend upon the oxygen content, and the effect of reducing oxygen content on the aqueous behavior of rGOs is not well understood.

In an effort to understand how properties of rGO change …

Inventions Of Scientists, Engineers And Specialists From Different Countries In The Area Of Nanotechnologies. Part Ii, Leonid A. Ivanov, Li Da Xu, Zhanna V. Pisarenko, Qiang Wang, Petr S. Prokopiev

Information Technology & Decision Sciences Faculty Publications

The article provides an abstract review of patents. The results of creative activity of scientists, engineers and specialists, including inventions in the field of nanotechnology and nanomaterials, being implemented, allow achieving a significant effect in construction, housing and community services, and related sectors of the economy. For example, the invention «Method for liquidphase synthesis of nanostructured ceramic material in the CeO2–Sm2O3 system to create a solid oxide fuel cell» can contribute to the active development of alternative, hydrogen energy. Fuel cells have a wide range of applications – from batteries in portable electronic devices to large-scale power generation and autonomous …

Inventions Of Scientists, Engineers And Specialists From Different Countries In The Area Of Nanotechnologies. Part Vi, Leonid A. Ivanov, Li D. Xu, Konstantin E. Razumeev, Zhanna V. Pisarenko, Aleksey V. Demenev

Information Technology & Decision Sciences Faculty Publications

Introduction. Advanced technologies impress people's imagination demonstrating the latest achievements (materials, methods, systems, technologies, devices etc.) that dramatically change the world. This, first of all, concerns nanotechnological inventions designed by scientists, engineers and specialists from different countries. Main part. The article provides an abstract overview of inventions of scientists, engineers and specialists from different countries: Russia, USA, China, Kazakhstan, Sweden. The results of the creative activity of scientists, engineers and specialists, including inventions in the field of nanotechnology and nanomaterials allow, when introduced to industry, achieving a significant effect in construction, housing and communal services, and related sectors of the …

Inventions Of Scientists, Engineers And Specialists From Different Countries In The Area Of Nanotechnologies. Part Iii, L. A. Ivanov, L. D. Xu, E. S. Bokova, A. V. Demenev, V. A. Ivanov

Information Technology & Decision Sciences Faculty Publications

Introduction. Advanced technologies impress people’s imagination demonstrating the latest achievements (materials, methods, systems, technologies, devices etc.) that dramatically change the world. This, first of all, concerns nanotechnological inventions designed by scientists, engineers and specialists from different countries.

Main part. The article provides an abstract review of patents. The results of creative activity of scientists, engineers and specialists, including inventions in the field of nanotechnology and nanomaterials, being implemented, allow achieving a significant effect in construction, housing and community services, and related sectors of the economy. For example, the invention «Composite material with oriented carbon nanotubes» refers to the area of …

Metal Filled Carbon Nanotubes In Radiation Therapy : Dose Enhancement Effect, Sarah Ashmeg

Legacy Theses & Dissertations (2009 - 2024)

In this work, the radiation dose enhancement is studied using a novel method and material that has not been widely investigated, at the time of this publication. Radiation dose enhancement is a useful technique in the field of radiation therapy, especially when dealing with radioresistant cells. Ideally, it increases the dose to the desired site with no additional damage to organs at risk.

Fabrication, Development, And Characterization Of Hipco Swcnt - Alginate Hydrogel Composites For Cellular Product Applications, Fabian Armando Alvarez-Primo

Open Access Theses & Dissertations

In this study, we designed, synthesized, and characterized ultrahigh purity single-walled carbon nanotube (SWCNT)-alginate hydrogel composites. Among the parameters of importance in the formation of an alginate-based hydrogel composite with single-walled carbon nanotubes, are their varying degrees of purity, their particulate agglomeration and their dose-dependent correlation to cell viability, all of which have an impact on the resultant compositeâ??s efficiency and effectiveness towards biomedical applications. To promote their homogenous dispersion by preventing agglomeration of the SWCNT, at first, we used three different surfactants-sodium dodecyl sulfate (SDS-anionic), cetyltrimethylammonium bromide (CTAB-cationic), and Pluronic F108 (nonionic). After experimentation and corroboration through evidence obtained …

Enzymatic Biofuel Cells In A Sandwich Geometry With Compressed Carbon Nanotubes/Enzyme Electrodes & Hybrid Patch Applications, Biao Leng

Dissertations

Enzymatic biofuel cells (EBFCs) convert the chemical energy of biofuels, such as glucose and methanol, into electrical energy by employing enzymes as catalysts. In contrast to conventional fuel cells, EBFCs have a simple membrane-free fuel cell design due to the high catalytic specificity of the enzymes, but the power densities obtained are lower. Although the primary goal of research on EBFCs has been to develop a sustainable power source that can be directly implanted in the human body to power bio-devices, other applications such as the use of a flexible film or fuel cell patch as a wearable power source …

Thermal Interface Material, Matthew Collins Weisenberger, John Davis Craddock

Center for Applied Energy Research Faculty Patents

A flexible sheet of aligned carbon nanotubes includes an array of aligned nanotubes in a free standing film form not adhered to the synthesis substrate, with a matrix infiltrated interstitially into the nanotube array with access to the nanotube tips from both the top and bottom. That is, the infiltrant is purposely limited from over-filling or coating one or both exterior top and/or bottom surfaces of the array, blocking access to the tips. A typical matrix is a polymer material.

Degradation Of Emerging Contaminants By Advanced Oxidation Using Multi-Walled Carbon Nanotubes And Continuous Ozone Injection, Emily N. Miller

Master's Theses

With a growing population and continuous accumulation of pollutants, water resources worldwide are quickly being depleted. Drastic improvements need to be made in both water conservation and treatment. Advanced oxidation processes (AOPs) have been developed to go above and beyond the capabilities of traditional wastewater treatment facilities to eliminate emerging contaminants from our water systems. AOPs increase the generation of hydroxyl radicals (•OH) in oxidation reactions, which are less selective and more reactive than other oxidants, such as ozone, so they are more effective at degrading persistent compounds. This study explored an AOP that utilizes ozonated multi-walled carbon nanotubes (MWCNTs) …

Electrical Properties And Electromagnetic Interference Shielding Effectiveness Of Interlayered Systems Composed By Carbon Nanotube Filled Carbon Nanofiber Mats And Polymer Composites, Claudia A. Ramirez-Herrera, Homero Gonzalez, Felipe De La Torre, Laura Benitez, Jose G. Cabanas-Moreno, Karen Lozano

Mechanical Engineering Faculty Publications

The demand for multifunctional requirements in aerospace, military, automobile, sports, and energy applications has encouraged the investigation of new composite materials. This study focuses on the development of multiwall carbon nanotube (MWCNT) filled polypropylene composites and carbon nanofiber composite mats. The developed systems were then used to prepare interlayered composites that exhibited improved electrical conductivity and electromagnetic interference (EMI) shielding efficiency. MWCNT-carbon nanofiber composite mats were developed by centrifugally spinning mixtures of MWCNT suspended in aqueous poly(vinyl alcohol) solutions. The developed nanofibers were then dehydrated under sulfuric acid vapors and then heat treated. Interlayered samples were fabricated using a nanoreinforced …

Method For Production Of Germanium Nanowires Encapsulated Within Multi-Walled Carbon Nanotubes, Mark Crocker, Rodney Andrews, Arumugam Pandurangan, Dali Qian

Center for Applied Energy Research Faculty Patents

A method is provided for producing germanium nanowires encapsulated within multi-walled carbon nanotubes. The method includes the steps of performing chemical vapor deposition using a combined germanium and carbon source having a general formula of GeR_(4-x)L_x, where x=0, 1, 2, or 3; R is selected from a group consisting of alkyl, cycloalkyl or aryl and L=hydrogen, halide or alkoxide and growing germanium nanowires encapsulated within multi-walled carbon nanotubes on a substrate. A reaction product of that method or process is also provided.

Mechanical Characterization Of Polymer Concrete With Nanomaterials, Alaeddin Douba

Civil Engineering ETDs

Nanomaterials are defined by those whose characteristic length scale lies within the nanometer scale. Their extreme dimension achieves extraordinary mechanical properties superior to other micro and macro additives. The introduction of nanotechnology to Civil Engineering utilizes low volume inclusions of nanomaterials to alter the properties of conventionally used bulk materials. Polymer Concrete (PC) where epoxy polymer binders replace cement binders, has become a common repair material among many other application and often can be considered an alternative to Portland cement concrete (PCC). PC is often used in bridge deck overlays, manholes, machine foundations and repairs. Its diverse chemical composition and …

Molecular Modeling Of Aerospace Polymer Matrices Including Carbon Nanotube-Enhanced Epoxy, Matthew Radue

Dissertations, Master's Theses and Master's Reports

Carbon fiber (CF) composites are increasingly replacing metals used in major structural parts of aircraft, spacecraft, and automobiles. The current limitations of carbon fiber composites are addressed through computational material design by modeling the salient aerospace matrix materials. Molecular Dynamics (MD) models of epoxies with and without carbon nanotube (CNT) reinforcement and models of pure bismaleimides (BMIs) were developed to elucidate structure-property relationships for improved selection and tailoring of matrices.

The influence of monomer functionality on the mechanical properties of epoxies is studied using the Reax Force Field (ReaxFF). From deformation simulations, the Young’s modulus, yield point, and Poisson’s ratio …

Confinement Effects And Magnetic Interactions In Magnetic Nanostructures, Kristen Lee Stojak Repa

USF Tampa Graduate Theses and Dissertations

Multifunctional nanocomposites are promising for a variety of applications ranging from microwave devices to biomedicine. High demand exists for magnetically tunable nanocomposite materials. My thesis focuses on synthesis and characterization of novel nanomaterials such as polymer nanocomposites (PNCs) and multi-walled carbon nanotubes (MWCNTs) with magnetic nanoparticle (NP) fillers.

Magnetite (Fe₃O₄) and cobalt ferrite (CoFe2O4) NPs with controlled shape, size, and crystallinity were successfully synthesized and used as PNC fillers in a commercial polymer provided by the Rogers Corporation and poly(vinylidene fluoride). Magnetic and microwave experiments were conducted under frequencies of 1-6 GHz in the presence of …

Investigation Of Carbon Nanomaterials Embedded In A Cementitious Matrix, Clarissa A. Roe

Masters Theses & Specialist Projects

The objective of this thesis was to investigate whether the addition of carbon nanofibers had an effect on the splitting tensile strength of Hydro-Stone gypsum concrete. The carbon nanofibers used were single-walled carbon nanotubes (SWNT), buckminsterfullerene (C60), and graphene oxide (GO). Evidence of the nanofibers interacting with gypsum crystals in a connective manner was identified in both 1 mm thick concrete discs and concrete columns possessing a height of 2 in and a diameter of 1 in. Before imaging, the columns were subjected to a splitting tensile strength test. The results illustrate that while there is a general decrease in …

Degradation And Exciton Energy Transfer Studies In Single-Walled Carbon Nanotube Bundles, Abhishek Gottipati

Legacy Theses & Dissertations (2009 - 2024)

Single walled carbon nanotubes (SWNTs) due to their unique optical behavior, large surface area, robust mechanical strength and electrical properties make them one of the ideal candidates for sensing and opto-electronic applications. In this work, we explore the energy transfer (exciton energy transfer-EET) phenomena occurring between nanotubes in bundles, using resonance Raman spectroscopy.

Effect Of Carbon Nanotubes On Anodic Properties Of Ti/Ru-Ir-Sn Oxides, Feng Lian, Yong-Lei Xin, Bo-Jiang Ma, Li-Kun Xu

Journal of Electrochemistry

The Ru-Ir-Sn metal oxide anodes coated on titanium (Ti/Ru-Ir-Sn) were prepared by thermal decomposition. The effects of amounts of carbon naotubes (CNTs) on anodic properties were studied by TGA, SEM, EDS, cyclic voltammetry, EIS, polarization measurements and accelerated life test. The thermogravimetric analysis and EDS spectrum data showed that the high temperature oxidation decomposition of CNTs did not take place under the condition of the sintering temperature of 470 ℃, and the CNTS still existed in the anode coating in an element form. Compared with the contrast samples, the surface crack of the coating increased, but remained typical morphology. Adding …

Fabrication And Material Characterization Of Copper And Copper-Cnt Micropillars, Siavash Ghanbari, Jeff Darabi

SIUE Faculty Research, Scholarship, and Creative Activity

In this work, copper micropillars and copper-carbon nanotube (CNT) composite micropillars were fabricated by incorporating an electrodeposition technique with a xurography process. In order to disperse carbon nanotubes in copper-CNT micropillars, various amounts of CNTs were added to the electroplating bath. Surface morphology and phase characterization of copper micropillars and copper-CNT composite micropillars were analyzed by optical microscopy and X-ray diffraction. In addition, the corrosion resistance (R_p) of a bare copper substrate, copper micropillars, and optimum copper-CNT micropillars were studied by electrochemical impedance spectroscopy (EIS) technique in a 3.5 wt. % sodium chloride. Experimental results yielded a corrosion …

Electrical And Physical Property Characterization Of Single Walled Carbon Nanotube Ink For Flexible Printed Electronics, Kristian E. Warner Jr.

Theses and Dissertations

This research presents a method of characterizing single-walled carbon nanotube (SWCNT) ink. This research also examines the results of our characterization efforts. First, the process of ink jet printing SWCNT ink onto organic and inorganic substrates is discussed. Next, the tests for measuring sheet resistance, conductance, inductance, adherence, thickness, roll-off, and S-parameters of the ink are described. Results and findings of the research are presented. The SWCNT ink created by Brewer Science © is shown to be an effective material for additive manufacturing using an aerosol jet printer, but not an inkjet printer. The ink is shown to have a …

Boosting Electrocatalytic Activity Of Nitrogen-Doped Graphene/Carbon Nanotube Composite For Oxygen Reduction Reaction, Yu Zhang, Jin-Song Hu, Wen-Jie Jiang, Lin Guo, Zi-Dong Wei, Li-Jun Wan

Journal of Electrochemistry

Developing low-cost catalysts with high electrocatalytic activity for oxygen reduction reaction (ORR) has recently attracted much attention because the sluggish ORR currently limits the performance and commercialization of fuel cells and metal-air batteries as well. Nitrogen doped carbon materials have been considered as a promising candidate for the replacement of high-cost and scarce Pt-based catalysts although their electrocatalytic activity still needs to be much improved. In this work, an improved nitrogen-doped graphene/carbon nanotubes composite (N-rGO/CNT) was developed as an efficient ORR electrocatalyst. It was found that the ORR activity of N-rGO/CNT composite could be significantly enhanced by introducing iron in …

A Sensitive And Label-Free Electrochemical Aptasensor Based On Signal Amplification Of Carbon Nanotubes, Chun-Yan Deng, Hui-Min Fan, Juan Xiang, Yuan-Jian Li

Journal of Electrochemistry

A label-free electrochemical sensing electrode for highly sensitive detection of adenosine was constructed based on the signal amplification of carbon nanotubes (CNTs). The change in the interfacial feature of the modified electrode was characterized by electrochemical impedance spectroscopy. Using [Ru(NH₃)₆]³⁺ as the signaling moiety, adenosine with concentrations as low as 0.027 nmol·L^-1 can be selectively detected. Additionally, the fabrication of this present aptasensor was simple, time-saving and cost-effective. Compared with other reported aptasensors, the proposed aptasensor had advantages of excellent sensitivity, selectivity and simplicity, which plays a potential role in development of aptasensor.