Nanoscience and Nanotechnology Commons^™

Harnessing Tio2-Based Nanofilaments: A Pathway To Enhanced Optoelectronic Performance In Dye-Sensitized And Perovskite Light Harvesters, Zahraa Ismail, Tarek A. Elmelegy, Hassan Nageh, Sameh Abdellatif

Mechanical Engineering

This study explores the integration of TiO2-based nanofilaments into dye-sensitized solar cells (DSSCs) and perovskite solar cells (PSCs) to enhance their optoelectronic performance. Despite the advancements in one-dimensional lepidocrocite TiO2 nanofilaments, there remains a significant gap in understanding their optical scattering mechanisms and dual applicability in both types of solar cells. We synthesized TiO2 nanofilaments and compared their performance to conventional P25 TiO2 in terms of morphology, electrical, and optical properties. The results indicate that the DSSC utilizing nanofilaments achieved a short-circuit current density of 8.2 mA/cm² and a power conversion efficiency (PCE) of 6.9%, compared to 7.1 mA/cm² and …

Rapid-Prototyping Nanofabrication: Lcd-Based Projection Lithography And Physical Vapor Deposition, Sabeel Saleem Mohammmed

University Honors Theses

The semiconductor industry's continued growth, driven in large part by demand for artificial intelligence hardware, has highlighted the need for greater workforce development in regions adjacent to major fabrication centers like Oregon's Silicon Forest. This capstone project lays the groundwork for a small scale and student led semiconductor fabrication lab at Portland State University by demonstrating two of the core steps in chip manufacturing: photolithography and thin film deposition. Rather than relying on conventional fixed reticles, this work explores a unique, low cost approach to patterning that uses an ultraviolet-compatible liquid crystal display (LCD) as a programmable reticle, allowing arbitrary …

Enhanced Triboelectric Effect Using Functionalized Multiwalled Carbon Nanotube-Coated Fiber Mats For Biomechanical Energy Harvesting, Fernando Viesca, Diego De Leon, Kevin Alejandro, Rigobert Ybarra Jr., Md. Wasikur Rahman, Victoria Padilla, Horacio Vasquez, Karen Lozano, M. Jasim Uddin

Mechanical Engineering Faculty Publications

Triboelectric nanogenerators (TENGs) have emerged as a cutting-edge technology for developing self-powered wearable electronic devices. In this study, TENGs were fabricated using two fiber mats: forcespun polytetrafluoroethylene (FS-PTFE) microfibers and electrospun polyvinyl alcohol (ES-PVA) nanofiber (NF) mats. The FS-PTFE mats were coated with functionalized multiwalled carbon nanotubes (MWCNTs). Functionalized MWCNTs were dispersed in water-based solutions containing three different surfactants—sodium dodecyl sulfate, sodium dodecylbenzene sulfonate, and Triton X-100 to enhance fiber interaction. The NF mats were subsequently immersed in aqueous systems. The surfactant facilitated the uniform deposition of COOH-MWCNTs onto the FS-PTFE fibers, serving as a negative layer, while ES-PVA mat …

Manufacturing Of Functional Surface Coatings In The Automotive Industry, Gulirano Saidakhmedova

Technical science and innovation

The development of environmentally sustainable technologies for material processing represents one of the most pressing scientific and technical challenges in modern industrial production. This issue is particularly relevant to the automotive industry, where growing demands for energy efficiency, durability, and environmental safety necessitate the adoption of advanced manufacturing methods. Special attention is given to developing vacuum-based, import-substituting equipment and technologies for producing functional coatings from composite materials with predefined physical, mechanical, and optical properties, including reflective and protective characteristics. Current requirements for mechanical engineering products and production technologies drive the need for innovative approaches to material processing and specialized technical …

Thermal Radiation Effects On Particles From Plasma Arc Radiation, Reece Davis, Joseph Mcgee

Williams Honors College, Honors Research Projects

Understanding the radiation heating and transport of both microparticles and nanoparticles is a phenomenon that is critical for both space and Earth sciences. In space, these particles are heated by plasma arcs within ionized space clouds or solar flares and can be present the path of deep space missions and orbital satellites. While on Earth, processes such as forest fires, nuclear fusion, and microchip manufacturing include the plasma arc heating of particles. These particles lay within the Mie Scattering Regime and Rayleigh Scattering Regime and emit radiation differently based on their diameter. New mathematical and computational modeling has been conducted …

Stiffening Of Soft Silicone Upon Deep Uv Treatment As Characterized Using Nanoindentation, Amanda Wilder, Zaria Booth, Caden Obermeyer, Saika Sharmin, Venkat Maruthamuthu

Mechanical & Aerospace Engineering Faculty Publications

Silicones are elastomers that have a wide variety of uses, including biomedical applications such as the coating of biomedical devices and as implants. Soft silicones with mechanical properties similar to those of biological tissues have particularly gained use as substrates for cell culture in mechanobiology studies. In this context, it would be desirable to be able to alter their surface mechanical properties with a relatively simple physical treatment. While deep ultraviolet (deep UV) or ultraviolet C (UV-C) treatment has been previously used as a surface treatment method for stiffer silicones formulations, the effect of this treatment on soft silicones relevant …

Material Degradation And Analysis Of N-Doped Graphene/Mof Nanocatalysts For Orr In Electrochemical Energy Systems, Niladri Talukder

Dissertations

The development of advanced electrochemical energy conversion and storage systems is crucial for achieving sustainable energy security. As alternatives to precious metal-based catalysts in electrochemical systems, especially for the oxygen reduction reaction (ORR), Nitrogen-doped Graphene with Metal-organic Frameworks (N-G/MOF) nanocatalysts have shown exceptional promise in recent years. This research advances the understanding of N-G/MOF nanocatalysts by systematically examining their structural features, degradation traits, correlated performance losses, and other aspects related to catalytic activities.

First, nitrogen-doped graphene (N-G) nanocatalysts were thoroughly investigated, resolving their physical properties, the influence of synthesis parameters, molecular-level material structures, and chemical and electronic structural details of …

Advancing Sustainable Co2 Mitigation: Experimental And Computational Analysis Of Thermal Carbon Chitosan Sorbent For Automotive Exhaust Capture, Dalia A. Ali Dr., Amir Ahmed Elgamal Eng., Rania Rushdy Moussa Dr.

Chemical Engineering

This study investigated the efficiency of thermal carbon chitosan (TCCS) sorbent for CO2 capture from vehicle exhaust emissions within a designed adsorption system. TCCS was synthesized and meticulously characterized using a series of analytical techniques, including Brunauer-Emmett-Teller (BET) surface area analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), Ther- mogravimetric Analysis (TGA), Energy Dispersive X-ray Spectroscopy (EDX), and Differential Scanning Calo- rimetry (DSC). The TCCS adsorbent showed high thermal stability and a heating value (HHV) of 23.5 MJ/kg. Adsorption isotherm study demonstrated that the maximum capacity of CO2 adsorption is 0.084 kg.CO2/kg. TCCS, as well …

Melamine-Based Polymer Nanofibers For Supercapacitors, Samar A. Salim, Hani Nasser Abdelhamid

Nanotechnology Research Centre

This investigation describes the synthesis, electrospinning, and characterization of melamine-glutaraldehyde (MAGA) polymer composites with polymethyl methacrylate (PMMA) for supercapacitors applications. Electrospun fibers are generated by combining the MAGA polymer with PMMA at varying concentrations (2.5 %, 5 %, and 10 wt%). The synthesis of the polymer, its morphological attributes, and structural features are validated by characterization methods e.g., XRD, TEM, SEM, and FT-IR. In a three-electrode configuration, the electrochemical performances of the prepared electrodes are assessed using cyclic voltammetry (CV), galvanostatic charge-discharge (GCDC), and linear sweep voltammetry (LSV). The results suggest that the 5 % MAGA-PMMA composite has a specific …

A Biocompatible Nitinol Based Triboelectric Stent Sensor For Prospective Cardiovascular Health Monitoring, Ulises Vidaurri Romero, Sk Shamim Hasan Abir, Najlah Karam, Mariana Torres, Shahria Ahmed, Md. Wasikur Rahman, Bahareh Azimi, Serena Danti, Jianzhi Li, M. Jasim Uddin

Mechanical Engineering Faculty Publications

Triboelectric nanogenerators (TENGs) have been considered as an effective approach for self-powered systems. Currently, coronary heart disease remains the leading cause of death in the United States. This can be easily resolved by balloon angioplasty or a specialized mesh tube called a stent. This study demonstrates a stent sensor made of nitinol, a nickel—titanium alloy used in the medical field for its pseudo-elasticity and strong corrosion resistance, poly(vinylidene fluoride) (PVDF) and polydimethylsiloxane (PDMS), which can measure several physiological parameters while placing it in the arteries. This nitinol health monitor sensor (NHMS) device thus integrates the TENG with a specific medical …

Synergistic Enhancement Of Tribological Behavior And Colloidal Stability In Cuo Nanolubricants Via Ligand Tuning, Sherif Elsoudy, Sayed Akl Akl Dr, Sayed Akl A. Akl Dr, Esm Lane, Abas Hadawey, Philip D. Howes

Mechanical Engineering

Nanoparticle-based lubricants, or nanolubricants, can exhibit superior tribological properties compared to unmodified base oils. However, these performance gains are highly dependent on the nanoparticle surface chemistry, particularly in maintaining stable colloidal dispersions. This study explores the influence of oleic acid (OA) and oleylamine (OAm) functionalization on the tribological and colloidal properties of CuO nanoparticles dispersed in an SAE 20W50 base oil. We present a hybrid optimization framework combining Response Surface Methodology (RSM) with Bayesian Optimization (BO) to identify the optimal OA to OAm ratio (OA–OAm) for CuO nanolubricants. Unlike prior studies that employed either RSM alone or trial-and-error approaches, this …

Tailoring Gel Polymer Electrolytes For Advancing Quasi-Solid-State Batteries, Linrui Duan, Juchen Zhang, Mataz Alcoutlabi, Hongtao Sun

Mechanical Engineering Faculty Publications

Gel polymer electrolytes (GPEs) have attracted considerable attention due to their advantageous properties, such as uniform lithium deposition, stable solid electrolyte interphase (SEI) formation, nontoxicity, nonflammability, and leak-proof characteristics. In this study, a polyvinylidene fluoride hexafluoropropylene copolymer (PVDF-HFP)-based gel polymer electrolyte is synthesized via photo-polymerization, with a focus on examining the effects of curing time on electrolyte performance. The findings reveal that UV irradiation conditions significantly influence key material and electrochemical properties of the GPEs, including lithium-ion transference number, ionic conductivity, crystallinity, morphology, and liquid electrolyte uptake. Notably, the GPE cured for 120 s exhibited optimized performance, achieving an ionic …

Exploring Metal Additive Manufacturing In Martian Atmospheric Environments, Zane Mebruer

Mechanical Engineering Undergraduate Honors Theses

On-surface manufacturing is key to the success of a planetary colonization, especially that of Mars. However, traditional subtractive manufacturing processes are equipment, energy, and material intensive, meaning novel additive manufacturing (AM) processes must be pursued for this end. Selective laser melting, one of the most effective and versatile AM methods, would be incredibly beneficial to a Martian mission but requires an artificial argon atmosphere to create effective parts. The purpose of this study was to examine if carbon dioxide, the gas that makes up over 95% of Mars’ surface atmosphere, would be a sufficient substitute for argon in SLM fabrication. …

Mechanistic Insights Into Polymer-Assisted Graphene Exfoliation: The Roles Of Velocity, Adhesion, Cohesion, Temperature, Peeling Mode, And Edge Defect Via Coarse-Grained Molecular Dynamics, Linjiale Dai

All Theses

Graphene exfoliation is a critical step in the fabrication of high-quality graphene

layers. However, the underlying fracture mechanisms remain poorly understood. In this

work, I employed coarse-grained (CG) molecular dynamics (MD) simulations to

investigate how factors such as interfacial binding energy, substrate cohesion, temperature,

peeling mode, and edge defects influence the outcome of the exfoliation process. To model

polymer-assisted mechanical exfoliation, I used a finite-size system in which multilayer

graphene (MLG) is sandwiched between two thin polymer films. Leveraging the

spatiotemporal efficiency of the CG model, I performed fifty simulation iterations per

parameter set and analyzed the results from a …

Investigating Spatial Mapping Of Lipid And Protein Alterations Within Cells And Tissues Using Raman Microspectroscopy, Elnaz Sheikh

LSU Doctoral Dissertations

The progression of various diseases is associated with alterations in the microenvironment of cells, consisting of a variety of metabolites like lipids and proteins. It is well known that lipids and proteins are potential biomarkers for indicating alterations within the cell microenvironment induced by disease, and various methods are frequently used for their examination. To understand the chemical composition and spatial distribution of constituents in tissues and cells, confocal Raman spectroscopy and microscopy, as non-destructive tools, have shown potential for monitoring abnormalities at the cellular level with high resolution and can facilitate detection through targeting multiple biomarkers. The application of …

Synthesis, Characterization And Electrical Properties Evaluation Of Zirconium Dioxide Capacitors, Thomas P. Chandy

USF Tampa Graduate Theses and Dissertations

This thesis focuses on the fabrication and comprehensive characterization of thin-film capacitors utilizing zirconium dioxide (ZrO2) as the dielectric material, placed between aluminum electrodes. The research primarily aims to examine the impact of varying ZrO2 film thickness and the effects of post-deposition annealing on the structural, morphological, and electrical properties of the capacitors. A controlled sputtering deposition technique was employed to ensure uniform film growth, maintaining consistency in thickness and material quality across all samples.

A comprehensive set of characterization techniques was employed to analyze the capacitors. Scanning electron microscope (SEM) was used to assess surface roughness, revealing fewer defects …

Synthesis, Characterization And Delamination Studies Of Metallic Thin Films Prepared Using Sputtering And Ebeam Evaporation Methods, Anoop Joseph

USF Tampa Graduate Theses and Dissertations

In many mechanical applications, including the manufacturing, automotive, and cutting tool sectors, metallic thin film coatings are crucial due to their tribological and protective properties. This research focuses on the development of metallic thin films of Aluminum (Al), Chromium (Cr) and Titanium (Ti) using deposition techniques like Sputtering and Electron Beam Evaporation. Metallic thin films were fabricated, with variations in thickness for each material, allowing for an in-depth study of the effects of Sputtering and Ebeam Evaporation deposition method on film characteristics. The thickness of these metallic thin films were evaluated using High-Resolution Scanning Electron Microscopy (HRSEM) and Profilometer while …

Material And Mechanical Characterization Of Sla 3d Printed Graphene Nanoplatelet-Based Nanocomposites Fabricated Within A Magnetic Field, Soka Suliman

Graduate Research Theses & Dissertations

The process of utilizing a static magnetic field to fabricate a nanomaterial-based composite via a stereolithography (SLA) 3D printing process is still a relatively new approach within the field of additive manufacturing. By using this magnetic field during the 3D printing process, both material and mechanical properties can be oriented and axially varied for enhanced characteristics. In this investigation, between 0% to 2% volume fractions of high aspect ratio, graphene nanoplatelets (GNP) are suspended within UV-curable resin during a SLA 3D printing process with a static magnetic field applied. The objective of this investigation is to determine the effect of …

Neodymium Doped Zinc Oxide Based Advanced Flexible Piezoelectric Energy Harvester And Self-Powered Biomotion Sensor, Muhtasim Ul Karim Sadaf, Abu Musa Abdullah, Haimanti Majumder, Sk Shamim Hasan Abir, Mariana Torres, Karen Lozano, Md. Wasikur Rahman, M. Jasim Uddin

Mechanical Engineering Faculty Publications

Flexible piezoelectric devices have garnered a lot of attention for their potential as energy harvesters and transducers. In this work, Neodymium (Nd) doped Zinc Oxide (ZnO) based flexible piezoelectric energy harvester and sensory device has been developed. Nd-doped ZnO has been synthesized using wet chemical co-precipitation and incorporated in Polyvinylidene Difluoride (PVDF) polymer matrix along with Multiwalled Carbon Nanotubes (MWCNT) to produce flexible piezoelectric films. The piezoelectric output of the device is tested at variable tapping frequency (60 to 240 BPM) and pressure (10 to 40 psi). The device has also been tested with conventional electronics like bridge rectifiers, capacitors, …

Fabrication And Charcaterization Of Pullulan-Collagen Nanofibers Via Forcespinning, Valeria Leon Leal

Theses and Dissertations

Extensive research on collagen has spurred advancements in tissue engineering and biomaterial development, given collagen´s pivotal role in regulating various tissue structures across diverse organisms. This study delves into fabricating nanocomposites utilizing collagen, along with silver nanoparticles, chondroitin sulfate and pullulan, for potential applications in antibacterial medical devices, and cell regeneration. Collagen, abundant in the extracellular matrix, provides essential structural support, while silver nanoparticles and chondroitin confer antimicrobial properties, crucial for combating infections. Pullulan, a polysaccharide polymer, serves as a biocompatible carrier for silver nanoparticles whilst being the starting nanofiber forming material. Utilizing Forcespinning® technology, composite nanofibers were successfully synthesized. …

Lithicone-Protected Lithium Metal Anodes For Lithium Metal Batteries With Nickel-Rich Cathode Materials, Ridwan A. Ahmed, Kevin V. Carballo, Krishna P. Koirala, Qian Zhao, Peiyuan Gao, Ju-Myung Kim, Cassidy S. Anderson, Xiangbo Meng, Chongmin Wang, Ji-Guang Zhang, Wu Xu

Mechanical Engineering Faculty Publications and Presentations

The high energy density advantage of lithium (Li) metal batteries (LMBs) makes them increasingly desirable; however, problems such as strong reactivity and dendrite growth of Li metal anode limit their practical uses. In this work, a novel Li-containing glycerol (LiGL) or lithicone protection layer on a 50 μm thick Li metal anode is employed for improving the performance of LMBs. This LiGL layer was accurately deposited via a molecular layer deposition (MLD) process at 150°C, using lithium tert-butoxide and glycerol as precursors. The as-formed LiGL coating layer is highly tunable in its thickness by simply adjusting MLD cycles and shows …

Attachment Of 2d Nanomaterials Onto 1d Nanofibers For Separation And Sensing Applications, Elmmer A. Vera Alvarado

Theses and Dissertations

Advancing materials for water desalination and sensing is essential for tackling global issues related to clean water and efficient energy systems. This thesis explores the application of 2D nanomaterials, specifically graphene, integrated onto 1D poly(vinylidene fluoride) (PVDF) nanofibers to enhance their effectiveness in these areas. Utilizing innovative techniques such as Forcespinning® and plasma treatment, PVDF nanofibers were strengthened with graphene and conductive polymers like poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT: PSS). The research involved thorough assessments using direct contact membrane distillation (DCMD) systems, oil-water separation tests, and various mechanical and electromechanical evaluations. Heat-pressed membranes consistently delivered a flux of 0.33 kg/m²/hr and …

Enhancement Of Polytetrafluoroethylene-Polyvinyl Alcohol Nanofibers Triboelectric Effect With Carboxylic Functionalized Multiwalled Carbon Nanotubes Coating, Fernando Viesca

Theses and Dissertations

In this study, we fabricated a TENG using Forcespinning® (FS) Polytetrafluoroethylene microfibers (FS-PTFE-MFs) and Electrospun (ES) Polyvinyl alcohol nanofibers (ES-PVA-NFs). The FS-PTFE-MFs were physically linked with functionalized carboxylic multiwall carbon nanotubes (MWCNTs-COOH) employing water dispersions. MWCNTs-COOH were dispersed using three different surfactants: Sodium Dodecyl Sulfate (SDS), Sodium dodecylbenzenesulfonate (SDBS), and Triton X-100 (TX-100). Coated FS-PTFE-MFs were then characterized using a field emission scanning electron microscope (FESEM) with an energy dispersive X-ray spectroscopy (EDS) attachment and Fourier-transform infrared spectroscopy (FTIR). While no significant difference in performance was observed with different surfactants, electrical results of the TENG recorded a notable enhancement of …

A Multi-Material Platform For Imaging Of Single Cell-Cell Junctions Under Tensile Load Fabricated With Two-Photon Polymerization, Jordan Rosenbohm, Grayson Minnick, Bahareh Tajvidi Safa, Amir M. Esfahani, Xiaowei Jin, Haiwei Zhai, Nickolay V. Lavrik, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

We previously reported a single-cell adhesion micro tensile tester (SCAμTT) fabricated from IP-S photoresin with two-photon polymerization (TPP) for investigating the mechanics of a single cell-cell junction under defined tensile loading. A major limitation of the platform is the autofluorescence of IP-S, the photoresin for TPP fabrication, which significantly increases background signal and makes fluorescent imaging of stretched cells difficult. In this study, we report the design and fabrication of a new SCAμTT platform that mitigates autofluorescence and demonstrate its capability in imaging a single cell pair as its mutual junction is stretched. By employing a two-material design using IP-S …

Electrokinetic Particle Trapping Performance Of Conductive Nanofiber Mats In Microfluidic Wells., Jacob Hunter West

Electronic Theses and Dissertations

The frequency dependence of electrokinetic particle trapping using large-area (>mm²) conductive carbon nanofiber (CNF) mat electrodes is investigated. The fibers provide nanoscale geometric features for the generation of high electric field gradients, which is necessary for particle trapping via dielectrophoresis (DEP). A device was fabricated with an array of microfluidic wells for repeated experiments; each well included a CNF mat electrode opposing an aluminum electrode. Fluorescent microspheres (1 µm) were trapped at various electric field frequencies between 30 kHz – 1 MHz. Digital images of each well were analyzed to quantify particle trapping. DEP trapping by the …

Injectable And Rapidly Expandable Thrombin-Decorated Cryogels Achieve Rapid Hemostasis And High Survival Rates In A Swine Model Of Lethal Junctional Hemorrhage, Syed Muntazir Andrabi, S.M. Shatil Shahriar, Al-Murtadha Al-Gahmi, Benjamin L. Wilczewski, Mark A. Carlson, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Effective therapies are urgently needed to stabilize patients with marginally compressible junctional hemorrhage long enough to get them to the hospital alive. Herein, we report injectable and rapidly expandable cryogels consisting of polyacrylamide and thrombin (AT cryogels) created by cryo-polymerization for the efficient management of lethal junctional hemorrhage in swine. The produced cryogels have small pore sizes and highly interconnected porous architecture with robust mechanical strength. The cryogels exhibit rapid shape memory properties and prove to be resilient against fatigue. These cryogels also show high water/blood absorption capacity, fast blood clotting effect, and enhanced adhesion of red blood cells and …

Copper−Cystine Biohybrid-Embedded Nanofiber Aerogels Show Antibacterial And Angiogenic Properties, Anik Karan, Navatha S. Polavaram, Margarita Darder, Yajuan Su, Syed Muntazir Andrabi, S M Shatil Shahriar, Johnson V. John, Zeyu Luo, Mark A. Decoster, Yu Shrike Zhang, Jingwei Xie

Department of Mechanical and Materials Engineering: Faculty Publications

Copper−cystine-based high aspect ratio structures (CuHARS) possess exceptional physical and chemical properties and exhibit remarkable biodegradability in human physiological conditions. Extensive testing has confirmed the biocompatibility and biodegradability of CuHARS under diverse biological conditions, making them a viable source of essential Cu²⁺. These ions are vital for catalyzing the production of nitric oxide (NO) from the decomposition of Snitrosothiols (RSNOs) found in human blood. The ability of CuHARS to act as a Cu²⁺ donor under specific concentrations has been demonstrated in this study, resulting in the generation of elevated levels of NO. Consequently, this dual function makes …

Smartphone Color Error Analysis, Mackenna Hawes

The Journal of Purdue Undergraduate Research

No abstract provided.

Implantation Of A Capsular Tension Ring During Cataract Surgery Attenuates Predicted Remodeling Of The Post-Surgical Lens Capsule Along The Visual Axis, Kurt A. Ameku, Caleb C. Berggren, Ryan M. Pedrigi

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction: Cataract surgery permanently alters the mechanical environment of the lens capsule by placing a hole in the anterior portion and implanting an intraocular lens (IOL) that has a very different geometry from the native lens. We hypothesized that implant configuration and mechanical interactions with the post-surgical lens capsule play a key role in determining long-term fibrotic remodeling.

Methods: We developed the first finite element-growth and remodeling (FE-G&R) model of the post-surgical lens capsule to evaluate how implantation of an IOL with and without a capsular tension ring (CTR) impacted evolving lens capsule mechanics and associated fibrosis over …

Engineering Neurotoxin-Functionalized Exosomes For Targeted Delivery To The Peripheral Nervous System, Mena Asha Krishnan, Olawale A. Alimi, Tianshu Pan, Mitchell Kuss, Zeljka Korade, Guoku Hu, Bo Liu, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

The administration of therapeutics to peripheral nerve tissue is challenging due to the complexities of peripheral neuroanatomy and the limitations imposed by the blood–nerve barrier (BNB). Therefore, there is a pressing need to enhance delivery effectiveness and implement targeted delivery methods. Recently, erythrocyte-derived exosomes (Exos) have gained widespread attention as biocompatible vehicles for therapeutics in clinical applications. However, engineering targeted Exos for the peripheral nervous system (PNS) is still challenging. This study aims to develop a targeted Exo delivery system specifically designed for presynaptic terminals of peripheral nerve tissue. The clostridium neurotoxin, tetanus toxin-C fragment (TTC), was tethered to the …