Nanoscience and Nanotechnology Commons^™

High Efficiency Excitation Of Plasmonic Waveguides With Vertically Integrated Resonant Bowtie Apertures, Edward C. Kinzel, Xianfan Xu

Birck and NCN Publications

In recent years, many nanophotonic devices have been developed. Much attention has been given to the waveguides carrying surface plasmon polariton modes with subwavelength confinement and long propagation length. However, coupling far field light into a nano structure is a significant challenge. In this work, we present an architecture that enables high efficiency excitation of nanoscale waveguides in the direction normal to the waveguide. Our approach employs a bowtie aperture to provide both field confinement and high transmission efficiency. More than six times the power incident on the open area of the bowtie aperture can be coupled into the waveguide. …

Resonant Oscillation Of Misch-Metal Atoms In Filled Skutterudites, Yaguo Wang, Xianfan Xu, Jihui Yang

Birck and NCN Publications

We investigate vibrational behaviors in misch-metal filled antimony skutterudites in the time domain. At higher filling ratios of guest atoms, the vibration frequency approaches that of the cage structure and the amplitude becomes stronger. Furthermore, the reduction of lattice thermal conductivity over a wide temperature range can be explained using the measured resonant vibrational frequency. These findings reveal that the reduction of the lattice thermal conductivity is a result of scattering of acoustic phonons due to the resonant interaction between guest atoms and lattice phonons.

Real Space First-Principles Derived Semiempirical Pseudopotentials Applied To Tunneling Magnetoresistance, Kirk Huw Bevan, Tony Low, H Guo

Birck and NCN Publications

We present a real space density functional theory localized basis set semiempirical pseudopotential (SEP) approach. The method is applied to iron and magnesium oxide, where bulk SEP and local spin density approximation band structure calculations are shown to agree within approximately 0.1 eV. Subsequently we investigate the qualitative transferability of bulk derived SEPs to Fe/MgO/Fe tunnel junctions. We find that the SEP method is particularly well suited to address the tight binding transferability problem because the transferability error at the interface can be characterized not only in orbital space (via the interface local density of states) but also in real …

Rarefied Gas Flow In Microtubes At Different Inlet-Outlet Pressure Ratios, Z Yang, Suresh Garimella

Birck and NCN Publications

A model is developed for rarefied gas flow in long microtubes with different inlet-outlet pressure ratios at low Mach numbers. The model accounts for significant changes in Knudsen number along the length of the tube and is therefore applicable to gas flow in long tubes encountering different flow regimes along the flow length. Predictions from the model show good agreement with experimental measurements of mass flow rate, pressure drop, and inferred streamwise pressure distribution obtained under different flow conditions and offer a better match with experiments than do those from a conventional slip flow model.

Automated Crystal Phase And Orientation Mapping Of Nanocrystals In A Transmission Electron Microscope, Peter Moeck, Sergei Rouvimov, Edgar F. Rauch, Stavros Nicolopoulos

Physics Faculty Publications and Presentations

An automated technique for the mapping of nanocrystal phases and orientations in a transmission electron microscope (TEM) is described. It is based on the projected reciprocal lattice geometry that is extracted from electron diffraction spot patterns. The required hardware allows for a scanning‐precession movement of the primary electron beam on the crystalline sample and can be interfaced to any newer or older TEM. The software that goes with this hardware is flexible in its intake of raw data so that it can also create orientation and phase maps of nanocrystal from high resolution TEM (HRTEM) images. When the nanocrystals possess …

Modulated Nanopores Using Pulse Anodization On Thin Aluminum, Mahesh Babu Gunukula

UNLV Theses, Dissertations, Professional Papers, and Capstones

Nanoporous anodic aluminum oxide has traditionally been made in one of two ways: "Mild Anodization (MA)" or "Hard Anodization (HA)". The former method produces self-ordered pore structures but it is slow and only works for a narrow range of processing conditions; the latter method, which is widely used in the aluminum industry, is faster but it produces films with disordered pore structures. Here we report a novel approach termed "pulse anodization" that combines the advantages of the MA and HA processes. By designing the pulse sequences it is possible to control both the composition and pore structure of the anodic …

Magnetic Sensors For Biodetection, Pranjali Vineet Sneha Deshpande

UNLV Theses, Dissertations, Professional Papers, and Capstones

The objective of thesis is to design magnetic sensor for detection of nanoparticles. Recently integrating the standard laboratory techniques into integrated system on chip is growing attention. Recent development is to combine magnetic markers and magnetoresistive sensors together in magnetic chip. In this thesis two magnetoresistive sensors were studied and designed.

By applying magnetic fields, magnetic nanoparticles can be manipulated on-chip, which can be utilized to pull the molecules to specific binding sites or to test the binding strength and distinguish between specifically and non-specifically bound molecules

Magnetoresistive sensors are compatible with the semiconductor industry which provides electronic signal directly …

Efficient Unidirectional Ridge Excitation Of Surface Plasmons, I P. Radko, S I. Bozhevolnyi, G Brucoli, L Mart´In-Moreno, F J. Garc´Ia-Vidal, A Boltasseva

Birck and NCN Publications

Using leakage-radiation microscopy, we characterize the efficiency of unidirectional surface-plasmon excitation with periodic (800 nm) arrays of 130-nm-high and 330-nm-wide gold ridges on a thin gold film illuminated with a focused (5-mu m-wide) laser beam. We demonstrate that, at the resonant wavelength of 816 nm, the excitation efficiency of > 0.4 can be obtained with >= 5 ridges by adjusting the beam position. Conducting numerical simulations, we account for the experimental results and calculate the electric-field enhancement achieved near the gold surface.

Unified Theory Of Gas Damping Of Flexible Microcantilevers At Low Ambient Pressures, Rahul Bidkar, Ryan Tung, Alina Alexeenko, Sumali Hartono, Arvind Raman

PRISM: NNSA Center for Prediction of Reliability, Integrity and Survivability of Microsystems

Predicting the gas damping of microcantilevers oscillating in different vibration modes in unbounded gas at low pressures is relevant for increasing the sensitivity of microcantilever-based sensors. While existing free-molecular theories are valid only at very high Knudsen numbers, continuum models are valid only at very low Knudsen numbers. We solve the quasisteady Boltzmann equation and compute a closed-form fit for gas damping of rectangular microcantilevers that is valid over four orders of magnitude of Knudsen numbers spanning the free-molecular, the transition, and the low pressure slip flow regimes. Experiments are performed using silicon microcantilevers under controlled pressures to validate the …

Reflection Contributions To The Dispersion Artefact In Ftir Spectra Of Single Biological Cells, Paul Bassan, Hugh Byrne, Joe Lee, Franck Bonnier, Colin Clarke, Paul Dumas, Ehsan Gazi, Michael Brown, Noel Clarke, Peter Gardner

Articles

Fourier transform infrared spectra of a single cell in transflection geometry are seen to vary significantly with position on the cell, showing a distorted derivative-like lineshape in the region of the optically dense nucleus. A similar behaviour is observable in a model system of the protein albumin doped in a potassium bromide disk. It is demonstrated that the spectrum at any point is a weighted sum of the sample reflection and transmission and that the dominance of the reflection spectrum in optically dense regions can account for some of the spectral distortions previously attributed to dispersion artefacts. Rather than being …

Characterization Of Electrochemically Grafted Molecular Layers On Silicon For Electronic Device Applications, Adina Scott, David B. Janes

Birck and NCN Publications

Recently, there has been considerable interest in developing organically functionalized silicon surfaces for a variety of applications including sensing and nanoelectronics. In this study, a series of as-deposited, para-substituted aryl-diazonium molecular layers covalently grafted to < 111 >-orientation silicon are characterized using a variety of surface analysis techniques. Collectively, these measurements suggest that relatively ideal molecular layers can be achieved with a variety of headgroups. Submonolayer amounts of silicon oxide are detected on all modified surfaces and the extent of silicon oxidation depends on the molecular substituent. For electronic device applications, it is necessary to apply contacts to molecular layers while maintaining …

Compact Model Of Squeeze-Film Damping Based On Rarefied Flow Simulations, Xiaohui Guo, Alina Alexeenko

PRISM: NNSA Center for Prediction of Reliability, Integrity and Survivability of Microsystems

A new compact model of squeeze-film damping is developed based on the numerical solution of the Boltzmann kinetic equation. It provides a simple expression for the damping coefficient and the quality factor valid through the slip, transitional and free-molecular regimes. In this work, we have applied statistical analysis to the current model using the chi-squared test. The damping predictions are compared with both Reynolds equation-based models and experimental data. At high Knudsen numbers, the structural damping dominates the gas squeeze-film damping. When the structural damping is subtracted from the measured total damping force, good agreement is found between the model …

Gold Nanorod-Mediated Photothermolysis Induces Apoptosis Of Macrophages Via Damage Of Mitochondria, Ling Tong, Ji-Xin Cheng

Other Nanotechnology Publications

Aims: Induction of apoptosis or necrosis in activated macrophages by gold nanorod-mediated photothermolysis is demonstrated and the mechanisms underlying the processes are investigated. Materials & methods: Gold nanorods were functionalized with cysteine-octaarginine peptides (R8-NRs). Uptake of R8-NRs by activated macrophages was monitored by two-photon luminescence imaging. The laser irradiation conditions were controlled to induce apoptosis or necrosis to R8-NR-internalized macrophages. Mitochondrial damage and reactive oxygen species overproduction during photothermolysis was investigated by confocal fluorescence microscopy and transmission-electron microscopy. Results: Activated macrophages efficiently uptake R8-NRs both in vitro and in live animals. Laser irradiation of internalized nanorods with controlled power density …

Toward Surround Gates On Vertical Single-Walled Carbon Nanotube Devices, Aaron D. Franklin, Robert A. Sayer, Timothy D. Sands, Timothy Fisher, David B. Janes

Birck and NCN Publications

The one-dimensional, cylindrical nature of single-walled carbon nanotubes (SWCNTs) suggests that the ideal gating geometry for nanotube field-effect transistors (FETs) is a surround gate (SG). Using vertical SWCNTs templated in porous anodic alumina, SGs are formed using top-down processes for the dielectric/metal depositions and definition of the channel length. Surround gates allow aggressive scaling of the channel to 25% of the length attainable with a bottom-gate geometry without incurring short-channel effects. The process demonstrated here for forming SGs on vertical SWCNTs is amenable for large-scale fabrication of multinanotube FETs.

Fatigue Evaluation Of Nanocomposites As Lightweight Electronic Enclosures For Satellites' Applications, Javier Rodriguez

Theses and Dissertations

Existing nanocomposite materials used for satellite applications don't offer the required conductivity and electromagnetic shielding protection, requiring metal shields in order to survive in space. The AFRL Materials and Manufacturing Directorate in conjunction with the private sector have developed a material that promises to blend the attributes of nanocomposites and metal materials. The M55J/RS3 material consists of carbon fibers combined with a polyisocyanate matrix, in which Nickel nanostrands^TM are added. The research effort investigated the changes in the EMI and ESD of the material after being subjected to cyclic loads. Four configurations of a symmetric layup with fibers oriented …

Patterning And Characterization Of Carbon Nanotubes Grown In A Microwave Plasma Enhanced Chemical Vapor Deposition Chamber, Mauricio Kossler

Theses and Dissertations

This research studies the growth of carbon nanotubes (CNT) from a nickel catalyst to be used on a field emission device. This thesis can be divided into three sections: the construction of a vacuum chamber for field emission testing, the design and fabrication of a triode structure to enable improved electron emission, and the pretreatment and growth of CNTs. To experimentally test the field emission of CNTs, a vacuum chamber must attain a vacuum of at least 10^-5 torr. Our vacuum chamber designed and built achieved a maximum, final pressure of 10^-8 torr. A triode structure was designed …

Electrostatic Discharge Properties Of Irradiated Nanocomposites, Joshua D. Mcgary

Theses and Dissertations

Modernization in space systems requires employment of new light-weight, high performance composite materials that reduce bulk weight and increase structural integrity. This thesis explored the behavior of one such material prior to and following a 35-year simulated space radiation life-cycle. Select electrical properties of nickel nanostrand^TM-carbon composites in seven configurations were characterized prior to electron irradiation via surface and bulk resistivity measurements and contact electrostatic discharge (ESD) measurements. Following irradiation at a fluence of 10¹⁶ e^-/cm² at an average energy of 500 keV, measurements were repeated and compared against pre-irradiation data. Configuration D is …

Interfacial Energy Between Carbon Nanotubes And Polymers Measured From Nanoscale Peel Tests In The Atomic Force Microscope, Mark C. Strus, Camilo I. Cano, R. Byron Pipes, Cattien V. Nguyen, Arvind Raman

Other Nanotechnology Publications

The future development of polymer composite materials with nanotubes or nanoscale fibers requires the ability to understand and improve the interfacial bonding at the nanotube-polymer matrix interface. In recent work [Strus MC, Zalamea L, Raman A, Pipes RB, Nguyen CV, Stach EA. Peeling force spectroscopy: exposing the adhesive nanomechanics of one-dimensional nanostructures. Nano Lett 2008;8(2):544–50], it has been shown that a new mode in the Atomic Force Microscope (AFM), peeling force spectroscopy, can be used to understand the adhesive mechanics of carbon nanotubes peeled from a surface. In the present work, we demonstrate how AFM peeling force spectroscopy can be …

Insights Into Few-Layer Epitaxial Graphene Growth On 4h-Sic(000(1)Over-Bar Substrates From Stm Studies, Laura B. Biedermann, Michael L. Bolen, Michael A. Capano, Dmitry Zemlyanov, R. Reifenberger

Birck and NCN Publications

Epitaxial carbon was grown by heating (000 (1) over bar) silicon carbide (SiC) to high temperatures (1450-1600 degrees C) in vacuum. A continuous graphene surface layer was formed at temperatures above 1475 degrees C. X-ray photo-electron spectroscopy (XPS) and scanning tunneling microscopy (STM) were extensively used to characterize the quality of the few-layer graphene (FLG) surface. The XPS studies were useful in confirming the graphitic composition and measuring the thickness of the FLG samples. STM studies revealed a wide variety of nanometer-scale features that include sharp carbon-rich ridges, moire superlattices, one-dimensional line defects, and grain boundaries. By imaging these features …

Toward Surround Gates On Vertical Single-Walled Carbon Nanotube Devices, Aaron D. Franklin, Robert A. Sayer, Timothy D. Sands, Timothy S. Fisher, David B. Janes

PRISM: NNSA Center for Prediction of Reliability, Integrity and Survivability of Microsystems

The one-dimensional, cylindrical nature of single-walled carbon nanotubes (SWCNTs) suggests that the ideal gating geometry for nanotube field-effect transistors (FETs) is a surround gate (SG). Using vertical SWCNTs templated in porous anodic alumina, SGs are formed using top-down processes for the dielectric/metal depositions and definition of the channel length. Surround gates allow aggressive scaling of the channel to 25% of the length attainable with a bottom-gate geometry without incurring short-channel effects. The process demonstrated here for forming SGs on vertical SWCNTs is amenable for large-scale fabrication of multinanotube FETs.

Theoretical Basis Of Parametric-Resonance-Based Atomic Force Microscopy, G Prakash, S Hu, Arvind Raman, R. Reifenberger

Birck and NCN Publications

Parametric resonance underpins the physics of swings, resonant surface waves, and particle traps. There is increasing interest in its potential applications in atomic force microscopy (AFM). In this paper, the dynamics of parametrically resonant microcantilevers for high sensitivity imaging and force spectroscopy applications is investigated theoretically. Detailed numerical parametric-resonance simulations are performed to understand how the microcantilever amplitude varies with tip-sample separation, the tip-sample interaction, and the scanning dynamics of a microcantilever probe. We find three key advantages of a parametrically resonant microcantilever for AFM applications: (a) the reduction in ringing effects near feature edges that occur for high-Q microcantilevers; …

The Effect Of Sintering Time On The Performance Of Spherical And Nano-Sized Lifepo4 Cathode Material, Zhong-Qiang Shan, Guo-Zeng Wang, Di Tian, Jian-Hua Tian

Journal of Electrochemistry

The spherical LiFePO₄ with nano-size is expected as an important direction for LiFePO₄ cathode materia1.With the method of liquid co-deposited-carbonthermal reduction,we prepared spherical LiFePO₄ cathode material with nano-size and we put our emphasis on the effect of sintering time on the material.By XRD,SEM,TEM and charge & discharge analysis,we found the sample sintered at 550 ℃ for 10 hours showed the best electrochemical properties and good degree of sphericity,with the size of 40～100 nm.

Electrochemical Properties Of Functionalized Carbon Nanotubes And Their Applications In Analysis Of 6-Mercaptopurine, Bao-Yi Lu, Yan-Yan Lai, Hong Li

Journal of Electrochemistry

The electrochemical behaviors and adsorption properties of single-walled carbon nanotubes such as SWNT,SWNT-COOH,and SWNT-OH and multi-walled carbon nanotubes including MWNT,MWNT-COOH,and MWNT-OH modified at a graphite electrode have been investigated by using [Fe(CN)₆]^3-anion and [Co(phen)₃]³⁺ cation.It was shown that shows good redox reversibility of [Fe(CN)₆]^3-/4-reactions on the existed carbon nanotubes(CNT) modified electrode.Based on the strong adsorptive property of [Co(phen)₃]³⁺ on the CNT surface,the [Co(phen)₃]³⁺/CNT modified graphite electrode can be obtained by progressive potential sweeping and developed to monitor quantitatively 6-mercaptopurine(6-MP).The adsorption capacity of …

Silicon Nanowires As Anode Materials For Lithium Ion Batteries, Yan-Peng Fu, Hui-Xin Chen, Yong Yang

Journal of Electrochemistry

The SiNWs electrodes were fabricated by coating and direct growth methods,respectively.The structure,morphology and electrochemical performance of such materials were characterized by XRD,SEM and charge-discharge tests.The results show that the electrodes prepared by direct growth method had higher capacity,better battery life and also displayed and excellent cyclability at higher currents.During the process of lithiation,the initial crystalline Si transformed to amorphous LixSi,and the average diameter of the SiNWs increased.Despite the large volume changed,the SiNWs remained intact and did not break into smaller particles.

Nano-Sn/Hard Carbon Composite As Anode Material For Lithium Ion Batteries, Bing-Kun Guo, Jie Shu, Kun Tang, Ying Bai, Zhao-Xiang Wang, Li-Quan Chen

Journal of Electrochemistry

The tin(Sn) nano particles were embedded into the mesopores of hard carbon spherules(HCS) to form a composite anode material for lithium ion batteries.The structure of the obtained composite was characterized by X-ray diffraction(XRD) while its electrochemical performances were evaluated with galvanostatic cycling.It is found that the embedding Sn nanoparticles into porous HCS not only result in a composite material with high lithium storage capacity and capacity retention,but also increase the initial coulombic efficiency of the composite.Based on the infrared spectroscopic analysis,the enhanced initial coulombic efficiency is attributed to the inductive decomposition of the ROCO₂Li species in the solid …

Photoelectrochemical Properties Of Tio2 Nanoparticles, Jie Qu, Ying Li, Qi-Wei Jiang, Xue-Ping Gao

Journal of Electrochemistry

The protonated titanate nanoparticles were obtained at room temperature and subsequently calcined at different temperatures(300 ℃,400 ℃,500 ℃,600 ℃ and 700 ℃) in air.The obtained products were characterized by XRD,TEM and UV-Vis.It is found that the grain sizes of TiO₂ nanoparticles calcined at 300 ℃ were about 20 nm,and increased gradually with the temperature rise.Photoelectric performance was measured with I～V curve and electrochemical impedance spectroscopy(EIS).The TiO₂ nanoparticles obtained at 500 ℃ showed the best photoelectrochemical properties with a photovoltaic conversion efficiency of 6.39%,which is much higher than those at other temperatures.In addition,it is also demonstrated that the charge …

Synthesis,Characteristics And Electrochemical Performance Of Nano-Sized Snco/Graphite Composites As Anode For Lithium Ion Batteries, Jin-Shu Cai, Ling Huang, Fu-Sheng Ke, Shi-Gang Sun

Journal of Electrochemistry

The nano-structural Sn-Co/graphite composites were prepared by chemical reduction of the alloy electroless deposition solution in graphite suspensions, and the composites were annealed at 500 ℃. The phase structure and surface morphology of the composites were measured by XRD, SEM and Raman. The results indicate that there were high dispersions and high loadings of Sn-Co nanoparticles on graphite by thermal treatment. Electrochemical lithium storage performance was studied preliminarily on the obtained samples. The graphite modified with the Sn-Co nanoparticles possessed a higher electrochemical reversible capacity than that of graphite during the charge and discharge process. The appetency between the Sn-Co …

High Utilization Aupt Nanoparticles Supported On Mwcnts For Methanol Electro-Oxidation In Alkaline Medium, Xun Guo, Dao-Jun Guo, Xin-Ping Qiu, Li-Quan Chen, Wen-Tao Zhu

Journal of Electrochemistry

We synthesized gold-platinum electrocatalysts supported on multi-walled carbon nanotubes(MWCNTs) with high utilization by a simple one-step method.A high Pt loading series of bimetallic AuPt/MWCNTs catalysts were prepared by the improved ethylene glycol reduction method,and then were compared in terms of the electrocatalytic activity for methanol electro-oxidation using cyclic voltammetry(CV) and chronoamperometry in alkaline solutions.The structure of AuPt/MWCNTs was characterized by the transmission electron microscopy(TEM),X-ray diffraction(XRD) and energy-dispersive X-ray spectroscopy(EDS).The results showed that the AuPt/MWCNTs catalysts had high Pt utilization,uniform AuPt nanoparticles size and good electrocatalytic activity for methanol electro-oxidation.The effect of Au/Pt mass ratio on electrocatalytic activity was also investigated.The …

A Ph-Tunable Hydrogel Microlens Array With Temperature-Actuated Light-Switching Capability, Zhenwen Deng, Babak Ziaie

Birck and NCN Publications

In this letter, we demonstrate a two step casting process to fabricate a bifunctional hydrogel-based microlens array, which responds to both temperature (becomes opaque above certain temperature) and pH (changes its focal length at different pH levels), and can be operated in air for an extended period of time. Each lens in the array is 1 mm in diameter and its focal length changes from 4.5 to 55 mm when the environmental pH is varied between 2.0 and 5.0. The light-switching capability is measured to be similar to 92% when temperature increases from 25 to 35 degrees C.

Compositional Contrast Of Biological Materials In Liquids Using The Momentary Excitation Of Higher Eigenmodes In Dynamic Atomic Force Microscopy, Xin Xu, John Melcher, Sudipta Basak, R. Reifenberger, Arvind Raman

Birck and NCN Publications

Atomic Force microscope (AFM) cantilevers commonly used for imaging soft biological samples in liquids experience a momentary excitation of the higher eigenmodes at each tap. This transient response is very sensitive to the local sample elasticity under gentle imaging conditions because the higher eigenmode time period is comparable to the tip-sample contact time. By mapping the momentary excitation response, we demonstrate a new scanning probe spectroscopy capable of resolving with high sensitivity the variations in the elasticity of soft biological materials in liquids.