Nanoscience and Nanotechnology Commons^™

The Application Of Graphene Films In Biosensing And Electrowetting, Xuebin Tan

Wayne State University Dissertations

In recent years, graphene has been found to possess extraordinary electronic, optical, mechanical and electrochemical properties. Graphene is optically transparent and mechanically flexible, and has high electron mobility and conductivity. In this thesis, we propose to investigate graphene's properties in the detection of biomolecules as well as the manipulation of biological samples. Graphene without defects has high charge carrier mobility and surface areas, which is ideal for biosensors. However, literature shows a lot of variations in the measurements using graphene biosensors. In addition, the surface functionalization of graphene in order to enhance the specificity has not been fully investigated yet. …

Dual Delivery Systems Based On Polyamine Analog Benspm As Prodrug And Gene Delivery Vectors, Yu Zhu

Wayne State University Dissertations

Combination drug and gene therapy shows promise in cancer treatment. However, the success of such strategy requires careful selection of the therapeutic agents, as well as development of efficient delivery vectors. BENSpm (N1, N11-bisethylnorspermine), a polyamine analogue targeting the intracellular polyamine pathway, draws our special attention because of the following reasons: (1) polyamine pathway is frequently dysregulated in cancer; (2) BENSpm exhibits multiple functions to interfere with the polyamine pathway, such as to up-regulate polyamine metabolism enzymes and down-regulate polyamine biosynthesis enzymes. Therefore BENSpm depletes all natural polyamines and leads to apoptosis and cell growth inhibition in a wide range …

Experimental Development Of Advanced Air Filtration Media Based On Electrospun Polymer Fibers, Negar Ghochaghi

Theses and Dissertations

Electrospinning is a process by which polymer fibers can be produced using an electrostatically driven fluid jet. Electrospun fibers can be produced at the micro- or nano-scale and are, therefore, very promising for air filtration applications. However, because electrospun fibers are electrically charged, it is difficult to control the morphology of filtration media. Fiber size, alignment and uniformity are very important factors that affect filter performance. The focus of this project is to understand the relationship between filter morphology and performance and to develop new methods to create filtration media with optimum morphology.

This study is divided into three focus …

Reference Compensation For Localized Surface-Plasmon Resonance Sensors, Neha Nehru

Theses and Dissertations--Electrical and Computer Engineering

Noble metal nanoparticles supporting localized surface plasmon resonances (LSPR) have been extensively investigated for label free detection of various biological and chemical interactions. When compared to other optical sensing techniques, LSPR sensors offer label-free detection of biomolecular interactions in localized sensing volume solutions. However, these sensors also suffer from a major disadvantage – LSPR sensors remain highly susceptible to interference because they respond to both solution refractive index change and non-specific binding as well as specific binding of the target analyte. These interactions can severely compromise the measurement of the target analyte in a complex unknown media and hence limit …

Polymer Aggregation Correlated Transition From Schottky-Junction To Bulk Heterojunction Organic Solar Cells, Bin Yang, Zhengguo Xiao, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

The fullerene-based organic Schottky-junction solar cells have recently attracted intensive research interest because of their unique electrical performance, such as significant photocurrent generation from excitons created in fullerenes and large open-circuit voltage (V_OC) output induced by high Schottky-barrier height between the anode and the fullerene acceptor. This manuscript reports another remarkably appealing advantage that the fullerene-based Schottky-junction solar cells are more stable than the bulk heterojunction counterparts. The better stability is likely due to mitigative polymer photo-oxidation and/or little morphological change of active film in the aged Schottky-junction devices. The transition from Schottky-junction to bulk heterojunction appears at …

Phase Transitions In Mechanically Milled Mn-Al-C Permanent Magnets, Michael J. Lucis, Timothy E. Prost, Xiujuan Jiang, Meiyu Wang, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Faculty Publications

Mn-Al powders were prepared by rapid solidification followed by high-energy mechanical milling. The rapid solidification resulted in single-phase ε. The milling was performed in both the ε phase and the τ phase, with the τ-phase formation accomplished through a heat treatment at 500 °C for 10 min. For the ε-milled samples, the conversion of the ε to the τ phase was accomplished after milling via the same heat treatment. Mechanical milling induced a significant increase in coercivity in both cases, reaching 4.5 kOe and 4.1 kOe, respectively, followed by a decrease upon further milling. The increase in coercivity was the …

Biomechanical Strain As A Trigger For Pore Formation In Schlemm’S Canal Endothelial Cells, Sietse T. Braakman, Ryan M. Pedrigi, A. Thomas Read, James A. E. Smith, W. Daniel Stamer, C. Ross Ethier, Darryl R. Overby

Department of Mechanical and Materials Engineering: Faculty Publications

The bulk of aqueous humor passing through the conventional outflow pathway must cross the inner wall endothelium of Schlemm’s canal (SC), likely through micron-sized transendothelial pores. SC pore density is reduced in glaucoma, possibly contributing to obstructed aqueous humor outflow and elevated intraocular pressure (IOP). Little is known about the mechanisms of pore formation; however, pores are often observed near dome-like cellular outpouchings known as giant vacuoles (GVs) where significant biomechanical strain acts on SC cells. We hypothesize that biomechanical strain triggers pore formation in SC cells. To test this hypothesis, primary human SC cells were isolated from three non-glaucomatous …

Altered Mechanobiology Of Schlemm’S Canal Endothelial Cells In Glaucoma, Darryl R. Overby, Enhua H. Zhou, Rocio Vargas-Pinto, Ryan M. Pedrigi, Rudolf Fuchshofer, Sietse T. Braakman, Ritika Gupta, Kristin M. Perkumas, Joesph M. Sherwood, Amir Vahabikashi, Quynh Dang, Jae Hun Kim, C. Ross Ethier, W. Daniel Stamer, Jeffrey J. Fredberg, Mark Johnson

Department of Mechanical and Materials Engineering: Faculty Publications

Increased flow resistance is responsible for the elevated intraocular pressure characteristic of glaucoma, but the cause of this resistance increase is not known. We tested the hypothesis that altered biomechanical behavior of Schlemm’s canal (SC) cells contributes to this dysfunction. We used atomic force microscopy, optical magnetic twisting cytometry, and a unique cell perfusion apparatus to examine cultured endothelial cells isolated from the inner wall of SC of healthy and glaucomatous human eyes. Here we establish the existence of a reduced tendency for pore formation in the glaucomatous SC cell—likely accounting for increased outflow resistance—that positively correlates with elevated subcortical …

Arising Applications Of Ferroelectric Materials In Photovoltaic Devices, Yongbo Yuan, Zhengguo Xiao, Bin Yang, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

The ferroelectric-photovoltaic (FE-PV) device, in which a homogeneous ferroelectric material is used as a light absorbing layer, has been investigated during the past several decades with numerous ferroelectric oxides. The FE-PV effect is distinctly different from the typical photovoltaic (PV) effect in semiconductor p–n junctions in that the polarization electric field is the driving force for the photocurrent in FE-PV devices. In addition, the anomalous photovoltaic effect, in which the voltage output along the polarization direction can be significantly larger than the bandgap of the ferroelectric materials, has been frequently observed in FE-PV devices. However, a big challenge faced by …

Organic Ferroelectric Evaporator With Substrate Cooling And In Situ Transport Capabilities, Keith Foreman, C. Labedz, M. Shearer, Shireen Adenwalla

Shireen Adenwalla Papers

We report on the design, operation, and performance of a thermal evaporation chamber capable of evaporating organic thin films. Organic thin films are employed in a diverse range of devices and can provide insight into fundamental physical phenomena. However, growing organic thin films is often challenging and requires very specific deposition parameters. The chamber presented here is capable of cooling sample substrates to temperatures below 130 K and allows for the detachment of the sample from the cooling stage and in situ transport. This permits the use of multiple deposition techniques in separate, but connected, deposition chambers without breaking vacuum …

Cnt Membrane Platforms For Transdermal Drug Delivery And Aptamer Modulated Transport, Tao Chen

Theses and Dissertations--Chemical and Materials Engineering

CNT membrane platforms are biomimetic polymeric membranes imbedded with carbon nanotubes which show fast fluid flow, electric conductivity, and the ability to be grafted with chemistry. A novel micro-dialysis probe nicotine concentration sampling technique was proposed and proved in vitro, which could greatly improve the efficiency and accuracy of future animal transdermal studies. To enhance the scope of transdermal drug delivery which was limited to passive diffusion of small, potent lipophilic drugs, a wire mesh lateral electroporation design was also proposed which could periodically disrupt the skin barrier and enhance drug flux.

It was shown that AMP binding aptamer …

Addressing Public Health Risks Of Persistent Pollutants Through Nutritional Modulation And Biomimetic Nanocomposite Remediation Platforms, Bradley J. Newsome

Theses and Dissertations--Chemistry

Due to their relative chemical stability and ubiquity in the environment, chlorinated organic contaminants such as polychlorinated biphenyls (PCBs) pose significant health risks and enduring remediation challenges. Engineered nanoparticles (NPs) provide a novel platform for sensing/remediation of these toxicants, in addition to the growing use of NPs in many industrial and biomedical applications, but there remains concern for their potential long-term health effects. Research highlighted herein also represents a transdisciplinary approach to address human health challenges associated with exposure to PCBs and NPs. The objectives of this dissertation research are two-fold, 1) to develop effective methods for capture/sensing and remediation …

Fluid Dynamic Modeling Of Nano-Thermite Reactions, Karen S. Martirosyan, Maxim Zyskin, Charles M. Jenkins, Yasuyuki Horie

Physics & Astronomy Faculty Publications

This paper presents a direct numerical method based on gas dynamic equations to predict pressure evolution during the discharge of nanoenergetic materials. The direct numerical method provides for modeling reflections of the shock waves from the reactor walls that generates pressure-time fluctuations. The results of gas pressure prediction are consistent with the experimental evidence and estimates based on the self-similar solution. Artificial viscosity provides sufficient smoothing of shock wave discontinuity for the numerical procedure. The direct numerical method is more computationally demanding and flexible than self-similar solution, in particular it allows study of a shock wave in its early stage …

Visible-Light Photocatalyzed Cross-Linking Of Diacetylene Ligands By Quantum Dots To Improve Their Aqueous Colloidal Stability, Marion G. Götz, Hiroko Takeuchi, Matthew J. Goldfogel, Julia M. Warren, Brandon D. Fennel, Colin D. Heyes

Chemistry & Biochemistry Faculty Publications and Presentations

Ligand cross-linking is known to improve the colloidal stability of nanoparticles, particularly in aqueous solutions. However, most cross-linking is performed chemically, in which it is difficult to limit interparticle cross-linking, unless performed at low concentrations. Photochemical cross-linking is a promising approach but usually requires ultraviolet (UV) light to initiate. Using such high-energy photons can be harmful to systems in which the ligand–nanoparticle bond is fairly weak, as is the case for the commonly used semiconductor quantum dots (QDs). Here, we introduce a novel approach to cross-link thiolated ligands on QDs by utilizing the photocatalytic activity of QDs upon absorbing visible …

Development Of A Nitrogen Incorporated Ultrananocrystalline Diamond Film Based Field Emitter Array For A Flat Panel X-Ray Source, Chrystian Mauricio Posada

Doctoral Dissertations

"As an alternative to conventional X-ray sources, a flat panel transmission X-ray source is being developed. A field emitter array (FEA) prototype to be incorporated as cold cathode in this flat panel X-ray source was fabricated for this work. Using the Particle-in-Cell code OOPIC Pro, an initial FEA was designed through simulations. Based on the simulation results, a FEA prototype was fabricated using conventional microfabrication techniques. Planar nitrogen-incorporated ultrananocrystalline diamond (N-UNCD) films were used as field emitters. This N-UNCD based FEA prototype was composed of 9 pixels distributed in a 3x3 array, with a pixel size of 225x225 µm, and …

Role Of Surface Chemistry In Nanoscale Electrokinetic Transport, Secuk Atalay

Mechanical & Aerospace Engineering Theses & Dissertations

This dissertation work presents the efforts to study the electrofluidics phenomena, with a focus on surface charge properties in nanoscale systems with the potential applications in imaging, energy conversion, ultrafiltration, DNA analysis/sequencing, DNA and protein transport, drug delivery, biological/chemical agent detection and micro/nano chip sensors.

Since the ion or molecular or particle transport and also liquid confinement in nano-structures are strongly dominated by the surface charge properties, in regards of the fundamental understanding of electrofluidics at nanoscale, we have used surface charge chemistry properties based on 2-pK charging mechanism. Using this mechanism, we theoretically and analytically showed the surface charge …

Fabrication Of Yttrium Ferrite Nanoparticles By Solution Combustion Synthesis, A. A. Saukhimov, Mkhitar A. Hobosyan, Gamage C. Dannangoda, N. N. Zhumabekova, S. E. Kumekov

Physics & Astronomy Faculty Publications

The ternary oxide system Y-Fe-O presents fascinating magnetic properties that are sensitive to the crystalline size of particles. There is a major challenge to fabricate these materials in nano-crystalline forms due to particle conglomeration during nucleation and synthesis. In this paper we report the fabrication of nano sized crystalline yttrium ferrite by solution combustion synthesis (SCS) where yttrium and iron nitrates were used as metal precursors with glycine as a fuel. The magnetic properties of the product can be selectively controlled by adjusting the ratio of glycine to metal nitrates. Yttrium ferrite nano-powder was obtained by using three concentration of …

Optical Properties Of Gallium-Doped Zinc Oxide-A Low-Loss Plasmonic Material: First-Principles Theory And Experiment, Jongbum Kim, Gururaj V. Naik, Alexander V. Gavrilenko, Krishnaveni Dondapati, Vladimir I. Gavrilenko, S. M. Prokes, O. J. Glembocki, V. M. Shalaev, Alexandra Boltasseva

Birck and NCN Publications

Searching for better materials for plasmonic and metamaterial applications is an inverse design problem where theoretical studies are necessary. Using basic models of impurity doping in semiconductors, transparent conducting oxides (TCOs) are identified as low-loss plasmonic materials in the near-infrared wavelength range. A more sophisticated theoretical study would help not only to improve the properties of TCOs but also to design further lower-loss materials. In this study, optical functions of one such TCO, gallium-doped zinc oxide (GZO), are studied both experimentally and by first-principles density-functional calculations. Pulsed-laser-deposited GZO films are studied by the x-ray diffraction and generalized spectroscopic ellipsometry. Theoretical …

Controllable Synthesis Of Dispersed Spherical Fe3O4 Nanoparticles As Lithium-Inserted Materials, Hong-Li Zou, Wei-Shan Li

Journal of Electrochemistry

Dispersed spherical Fe₃O₄ nanoparticles were synthesized by a hydrothermal method. The influences of odecyl trimethyl ammonium bromide (DTAB) concentration on the morphology and particle size of the as-prepared Fe₃O₄ were studied. Electrochemical performance of the as-prepared sample as anode materials of lithium ion battery was investigated. It is found that the as-prepared sample exhibits superior rate performance and cycle performance. The nano-sized materials provide structural stability and favor the transfer of lithium ions.

Synthesis And Electrochemical Performance Of Nano Licopo4 By Polyol Method, Fei Wang, Yang Jun

Journal of Electrochemistry

High potential LiCoPO₄ cathode material was synthesized by polyol method. Carbon layer of ca. 3 nm thick was coated on the LiCoPO₄ surfaces by chemical vapor deposition from methylbenzene. Crystalline structure, morphology and electrochemical performance of the sample were studied by XRD, SEM, TEM, CV and galvanostatic charge/discharge curve. The synthesized material via polyol method showed a pure phase of LiCoPO₄. The LiCoPO₄/C electrode delivered a high discharge capacity of 132 mAh·g^-1 and maintained 78% of the initial capacity after 50 cycles at 0.1C rate. The two-step extraction/insertion behavior of Li⁺ in …

Surface Composition Structure And Electrochemical Performance Of Aluminum Doped Lifepo4, Huai-Fang Shang, Wei-Feng Huang, Wang-Sheng Hu, Ding-Guo Xia, Zi-Yu Wu

Journal of Electrochemistry

Despite there are many successful reports about the preparation of electrode materials with surface coating for lithium ion batteries, the study in surface self-coating of cathode materials using segregation of doping elements and their electrochemical properties is still very rare. The LiFePO₄ particles with rich-Al on the surface were synthesized by one step solvothermal route. TEM results demonstrated that the surface of the obtained LiFePO₄ particles was well-covered by the amorphous coating. The soft X-ray absorption spectroscopy (XAS) and Auger electron spectroscopy (AES) component analyses revealed that the amorphous coating was composed of LiFe_1-xAl_xPO …

Spatial Spectrograms Of Vibrating Atomic Force Microscopy Cantilevers Coupled To Sample Surfaces, Ryan Wagner, Arvind Raman, Roger Proksch

Birck and NCN Publications

Many advanced dynamic Atomic Force Microscopy (AFM) techniques such as contact resonance, force modulation, piezoresponse force microscopy, electrochemical strain microscopy, and AFM infrared spectroscopy exploit the dynamic response of a cantilever in contact with a sample to extract local material properties. Achieving quantitative results in these techniques usually requires the assumption of a certain shape of cantilever vibration. We present a technique that allows in-situ measurements of the vibrational shape of AFM cantilevers coupled to surfaces. This technique opens up unique approaches to nanoscale material property mapping, which are not possible with single point measurements alone. (C) 2013 AIP Publishing …

The Role Of Oxygen In The Uptake Of Deuterium In Lithiated Graphite, C. N. Taylor, J. Dadras, Kara E. Luitjohan, Jean P. Allain, P. S. Kristic, C. H. Skinner

Birck and NCN Publications

We investigate the mechanism of deuterium retention by lithiated graphite and its relationship to the oxygen concentration through surface sensitive experiments and atomistic simulations. Deposition of lithium on graphite yielded 5%-8% oxygen surface concentration and when subsequently irradiated with D ions at energies between 500 and 1000 eV/amu and fluences over 10(16) cm(-2) the oxygen concentration rose to between 25% and 40%. These enhanced oxygen levels were reached in a few seconds compared to about 300 h when the lithiated graphite was allowed to adsorb oxygen from the ambient environment under equilibrium conditions. Irradiating graphite without lithium deposition, however, resulted …

Limit For Thermal Transport Reduction In Si Nanowires With Nanoengineered Corrugations, Sean E. Sullivan, Keng-Hua Lin, Stanislav Avdoshenko, Alejandro Strachan

Birck and NCN Publications

Non-equilibrium molecular dynamics simulations reveal that the thermal conductance of Si nanowires with periodic corrugations is lower than that of smooth wires with cross-sections equivalent to the constricted portions. This reduction in conductance is up to 30% and tends to plateau with increasing corrugation height. Spatially resolved temperature and heat current maps provide a microscopic understanding of this effect; we find that 80% of the heat current is carried through the constricted area even for high-amplitude corrugations. More importantly, we show that temperature gradient inversion and heat current vortices at the ridge peaks establish fundamental limits on maximum conductance reduction. …

Homogeneous Algan/Gan Superlattices Grown On Free-Standing (1(1)Over-Bar00) Gan Substrates By Plasma-Assisted Molecular Beam Epitaxy, Jiayi Shao, Dmitri N. Zakharov, Collin Edmunds, Oana Malis, Michael J. Manfra

Birck and NCN Publications

Two-dimensional and homogeneous growth of m-plane AlGaN by plasma-assisted molecular beam epitaxy has been realized on free-standing (1 (1) over bar 00) GaN substrates by implementing high metal-to-nitrogen (III/N) flux ratio. AlN island nucleation, often reported for m-plane AlGaN under nitrogen-rich growth conditions, is suppressed at high III/N flux ratio, highlighting the important role of growth kinetics for adatom incorporation. The homogeneity and microstructure of m-plane AlGaN/GaN superlattices are assessed via a combination of scanning transmission electron microscopy and high resolution transmission electron microscopy (TEM). The predominant defects identified in dark field TEM characterization are short basal plane stacking faults …

Friction And Wear Of Polytetrafluoroethylene/Graphene Oxide Composite Thin Films, Justin Kyle Carter

Graduate Theses and Dissertations

Polytetrafluoroethylene (PTFE) is a commonly used solid lubricant due to its low coefficient of friction and chemical inertness. As a polymer, PTFE suffers from high wear and low adhesion to substrates limiting its use as a thin film. Thin PTFE films are ideal candidates for solid lubrication in micro-machines and bearing applications. The main goal of this work is to enhance the durability of thin PTFE films through the addition of few layered graphene oxide (GO) as filler. In order to address adhesion issues, the addition of an adhesive layer of polydopamine (PDA) between stainless steel substrates and thin PTFE …

Assessing Different Zeolitic Adsorbents For Their Potential Use In Kr And Xe Separation, Breetha Alagappan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Separation of Kr from Xe is an important problem in spent nuclear fuel fission gas management. The energy intensive and expensive cryogenic distillation method is currently used to separate these gases. In this thesis, we have carried out the research into appropriate sorbents for the separation of Kr and Xe using pressure swing adsorption. We have examined zeolites using gas adsorption studies as they have the potential to be more cost effective than other sorbents. Zeolites are microporous aluminosilicates and have ordered pore structures. The pores in zeolites have extra-framework cations are substantially free to move. The mobility of cations …

Near-Infrared Surface-Enhanced Fluorescence Using Silver Nanoparticles In Solution, Michael D. Furtaw

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Fluorescence spectroscopy is a widely used detection technology in many research and clinical assays. Further improvement to assay sensitivity may enable earlier diagnosis of disease, novel biomarker discovery, and ultimately, improved outcomes of clinical care along with reduction in costs. Near-infrared, surface-enhanced fluorescence (NIR-SEF) is a promising approach to improve assay sensitivity via simultaneous increase in signal with a reduction in background. This dissertation describes research conducted with the overall goal to determine the extent to which fluorescence in solution may be enhanced by altering specific variables involved in the formation of plasmonactive nanostructures of dye-labeled protein and silver nanoparticles …

An Integrated Multidisciplinary Nanoscience Concentration Certificate Program For Stem Education, Karen S. Martirosyan, Mikhail M. Bouniaev, Malik Rakhmanov, Ahmed Touhami, Nazmul Islam, Davood Askari, Tarek Trad, Dmitri Litvinov, Sergey E. Lyshevski

Physics & Astronomy Faculty Publications

Integration of nanoscience and nanotechnology curricula into the College of Science, Mathematics, and Technology (CSMT) at the University of Texas at Brownsville (UTB) is reported. The rationale for the established multidisciplinary Nanoscience Concentration Certificate Program (NCCP) is to: (i) develop nanotechnology-relevant courses within a comprehensive Science, Engineering and Technology curriculum, and, to offer students an opportunity to graduate with a certificate in nanoscience and nanotechnology; (ii) to contribute to students' success in achieving student outcomes across all college's majors, and, improve the breath, depth and quality of science, technology, engineering and mathematics (STEM) graduates' education; (iii) through NCCP, recruit certificate- …

Zinc Oxide Nanorod Based Ultraviolet Detectors With Wheatstone Bridge Design, Arun Vasudevan

Graduate Theses and Dissertations

This research work, for the first time, investigated metal semiconductor-metal (MSM) zine oxide (ZnO) nanorod based ultra-violet (UV) detectors having a Wheatstone bridge design with a high

responsivity at room temperature and above, as well as a responsivity that was largely independent of the change in ambient conditions. The ZnO nanorods which acted as the sensing element of the detector were grown by a chemical growth technique. Studies were conducted to determine the effects on ZnO nanorod properties by varying the concentration of the chemicals used for the rod growth. These studies showed how the rod diameter and the deposition …