Nanoscience and Nanotechnology Commons^™

Waveguide-Coupled Avalanche Photodiodes For A Cmos Compatible Tranceiver Package, Nick Martinez

Nanoscience and Microsystems ETDs

Optical signal detection is most readily done with classical sources emitting signals

which undergo very little attenuation. Detection of signals with these power levels

benets from classical photodetectors, where the photon induced electronic signal is

discernible above the background noise. In other instances, where the optical signal

may start from an attenuated source, or in cases where the optical signal is severely

attenuated in transit, a detector which exhibits gain converts a weak optical signal

into a measurable electrical one. Detectors which convert a weak photo-generated

electrical pulse into a strong one do so through a process known as carrier …

Role Of Vapor Phase Processes On The Sintering Of Diesel Oxidation Catalysts, Cristhian Carrillo

Nanoscience and Microsystems ETDs

This work provides a fundamental understanding on the vapor phase processes that govern the sintering of supported nanoparticles in relation to the diesel oxidation catalyst (DOC). Sintering is a deactivation process that affects this catalyst significantly, and many other catalyst systems. Therefore, it is important to understand the sintering mechanisms in order to improve the long term catalytic reactivity.

Pt is an active catalyst in the DOC but it sinters via Ostwald ripening to form large particles under the accelerated aging conditions (800 ^oC) recommended by the Department of Energy (DOE). At 800 ^oC in the presence of …

Meniscus-Assisted Solution Printing Of Largegrained Perovskite Films For High-Efficiency Solar Cells, Ming He, Bo Li, Xun Cui, Beibei Jiang, Yanjie He, Yihuang Chen, Daniel O'Neil, Paul Szymanski, Mostafa A. El-Sayed, Jinsong Huang, Zhiqun Lin

Department of Mechanical and Materials Engineering: Faculty Publications

Control over morphology and crystallinity of metal halide perovskite films is of key importance to enable high-performance optoelectronics. However, this remains particularly challenging for solution-printed devices due to the complex crystallization kinetics of semiconductor materials within dynamic flow of inks. Here we report a simple yet effective meniscus-assisted solution printing (MASP) strategy to yield large-grained dense perovskite film with good crystallization and preferred orientation. Intriguingly, the outward convective flow triggered by fast solvent evaporation at the edge of the meniscus ink imparts the transport of perovskite solutes, thus facilitating the growth of micrometre-scale perovskite grains. The growth kinetics of perovskite …

Study Of Polysulfide Speciation In Lithium Sulfur Batteries Using In Situ Confocal Raman Microscopy, Josefine Mcbrayer

Nanoscience and Microsystems ETDs

Secondary lithium sulfur (Li-S) batteries have been heavily studied in the battery community since the start of the 21^st century due to their high theoretical capacity and specific energy density. The ground-breaking lithium ion battery has revolutionized society and its ability to store energy, however the lithium ion battery is reaching its limit with a theoretical capacity almost five times lower than that of lithium sulfur. With the improvement and commercialization of Li-S batteries, electric vehicles and personal electronics will have extended performance on a single charge. The viability of this promising chemistry relies on overcoming several key difficulties, …

Bisphosphonate Functionalized Gold Nanoparticles For The Study And Treatment Of Osteoporotic Disease, Christopher Conners

USF Tampa Graduate Theses and Dissertations

The use of nanoparticles for disease treatment is an increasingly popular area of research. The potential for multi-functionality allows nanoparticles to be used as transport and delivery vehicles for drugs and as diagnostic aides, among other applications, to address the unmet needs of many disease treatments. One such class of disease is osteoporosis including severe disorders, like Paget’s disease, Osteogenesis Imperfecta and Legg Calve Perthes disease. In this dissertation, we discuss a nanoparticle system consisting of gold nanoparticles surface functionalized with primary amine bisphosphonates, which is a classification of pharmaceuticals that is common in the treatment of osteoporosis. Functionalized nanoparticles …

Size And Shape Distributions Of Primary Crystallites In Titania Aggregates, Eric A. Grulke, Kazuhiro Yamamoto, Kazuhiro Kumagai, Ines Häusler, Werner Österle, Erik Ortel, Vasile-Dan Hodoroaba, Scott C. Brown, Christopher Chan, Jiwen Zheng, Kenji Yamamoto, Kouji Yashiki, Nam Woong Song, Young Heon Kim, Aleksandr B Stefaniak, D. Schwegler-Berry, Victoria A. Coleman, Åsa K. Jämting, Jan Herrmann, Toru Arakawa, Woodrow W. Burchett, Joshua W. Lambert, Arnold J. Stromberg

Chemical and Materials Engineering Faculty Publications

The primary crystallite size of titania powder relates to its properties in a number of applications. Transmission electron microscopy was used in this interlaboratory comparison (ILC) to measure primary crystallite size and shape distributions for a commercial aggregated titania powder. Data of four size descriptors and two shape descriptors were evaluated across nine laboratories. Data repeatability and reproducibility was evaluated by analysis of variance. One-third of the laboratory pairs had similar size descriptor data, but 83% of the pairs had similar aspect ratio data. Scale descriptor distributions were generally unimodal and were well-described by lognormal reference models. Shape descriptor distributions …

Elastic Properties Of Superconductors And Materials With Weakly Correlated Spins, Christian Binek

Christian Binek Publications

It is shown that in the ergodic regime, the temperature dependence of Young’s modulus is solely determined by the magnetic properties of a material. For the large class of materials with paramagnetic or diamagnetic response, simple functional forms of the temperature derivative of Young’s modulus are derived and compared with experimental data and empirical results. Superconducting materials in the Meissner phase are ideal diamagnets. As such, they display remarkable elastic properties. Constant diamagnetic susceptibility gives rise to a temperature independent elastic modulus for ceramic and single crystalline superconductors alike. The thermodynamic approach established in this report, paves the way to …

The Efficacy Of Programming Energy Controlled Switching In Resistive Random Access Memory (Rram), David Malien Nminibapiel

Electrical & Computer Engineering Theses & Dissertations

Current state-of-the-art memory technologies such as FLASH, Static Random Access Memory (SRAM) and Dynamic RAM (DRAM) are based on charge storage. The semiconductor industry has relied on cell miniaturization to increase the performance and density of memory technology, while simultaneously decreasing the cost per bit. However, this approach is not sustainable because the charge-storage mechanism is reaching a fundamental scaling limit. Although stack engineering and 3D integration solutions can delay this limit, alternate strategies based on non-charge storage mechanisms for memory have been introduced and are being actively pursued.

Resistive Random Access Memory (RRAM) has emerged as one of the …

Dissipative Elastic Metamaterial With A Lowfrequency Passband, Yongquan Liu, Jianlin Yi, Zheng Li, Xianyue Su, Wenlong Li, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

We design and experimentally demonstrate a dissipative elastic metamaterial structure that functions as a bandpass filter with a low-frequency passband. The mechanism of dissipation in this structure is well described by a mass-spring-damper model that reveals that the imaginary part of the wavenumber is non-zero, even in the passband of dissipative metamaterials. This indicates that transmittance in this range can be low. A prototype for this viscoelastic metamaterial model is fabricated by 3D printing techniques using soft and hard acrylics as constituent materials. The transmittance of the printed metamaterial is measured and shows good agreement with theoretical predictions, demonstrating its …

Multiple Scattering Theory For Heterogeneous Elastic Continua With Strong Property Fluctuation: Theoretical Fundamentals And Applications, Huijing He

Department of Mechanical and Materials Engineering: Faculty Publications

Scattering of elastic waves in heterogeneous media has become one of the most important problems in the field of wave propagation due to its broad applications in seismology, natural resource exploration, ultrasonic nondestructive evaluation and biomedical ultrasound. Nevertheless, it is one of the most challenging problems because of the complicated medium inhomogeneity and the complexity of the elastodynamic equations. A widely accepted model for the propagation and scattering of elastic waves, which properly incorporates the multiple scattering phenomenon and the statistical information of the inhomogeneities is still missing. In this work, the author developed a multiple scattering model for heterogeneous …

Characteristics And Mechanism For The Simons Electrochemical Fluorination Of Methanesulfonyl Fluoride, Wen-Lin Xu, Bao-Tong Li, Da-Wei Wang, Ya-Qiong Wang

Journal of Electrochemistry

The characteristics and mechanism for the Simons electrochemical fluorination processes were investigated during the electrochemical fluorination of CH₃SO₂F to CF₃SO₂F. The results showed that the reaction mechanism for the electrochemical fluorination of organic compounds to organic fluorides was the same as that of chemical fluorination processes using fluorinating agents such as CoF₃. The electrochemical fluorination in anhydrous HF was a heterogeneous process, and nickel fluorides on the surface of the nickel anode played the role of a mediator in the Simons process to transfer oxidation potential from the anode to …

Electrocatalysis Of Nanotin Dioxide In The Battery Reaction Of Zinc-Nitrobenzene, Xu-Guo Tu, Xiang-Yu Ma, Rui-Nan He, Xiao-Juan Wang, Chen Ling, Yun-Xia Sun, Song Chen

Journal of Electrochemistry

The tin dioxide (SnO₂) nanoparticles were synthesized by using a simple hydrothermal route in the presence of tetrapropyl ammonium bromide (TPAB) as a surfactant. Accordingly, the titanium mesh based SnO₂ catalyst electrode was prepared. The morphologies and structures of SnO₂ nanostructures were characterized by scanning electron microscopy and X-ray diffraction spectrometry. The influences of reactant concentration, reaction temperature and time on the morphology of the products were investigated in detail. The electrocatalytic performance of SnO₂ for the reduction of nitrobenzene with zinc was studied. Possible formation process and growth mechanism for such hierarchical SnO_{2 …}

A Strategy To Optimize Recovery In Orthopedic Sports Injuries, Michael P. Sealy, Ziye Liu, Chao Li, Yuebin Guo, Ben White, Mark Barkey, Brian Jordon J, Luke N. Brewer, Dale Feldman

Department of Mechanical and Materials Engineering: Faculty Publications

An important goal for treatment of sports injuries is to have as short a recovery time as possible. The critical problem with current orthopedic implants is that they are designed to be permanent and have a high complication rate (15%) that often requires removal and replacement with a second surgery; and subsequently a second rehabilitation cycle. This study was designed to test the feasibility of having a device that could provide the needed mechanical properties, while promoting healing, for a specified amount of time and then degrade away, to shorten the recovery time. The specific strategy was to create a …

Enhanced Visible Light Photocatalytic Remediation Of Organics In Water Using Zinc Oxide And Titanium Oxide Nanostructures, Srikanth Gunti

USF Tampa Graduate Theses and Dissertations

The techniques mostly used to decontaminate air as well as water pollutants have drawbacks in terms of higher costs, require secondary treatment, and some methods are very slow. So, emphasis has been given to water though the use of photocatalysts, which break organic pollutants to water and carbon dioxide and leave no trace of by-products at the end. Photocatalytic remediation aligns with the waste and wastewater industries’ zero waste schemes with lower cost, eco-friendly and sustainable treatment technology. The commonly used photocatalysts such as titanium oxide (TiO₂), zinc oxide (ZnO), tungsten oxide (WO₃) have band gap …

Mechanical Characterization Of Polymer Concrete With Nanomaterials, Alaeddin Douba

Civil Engineering ETDs

Nanomaterials are defined by those whose characteristic length scale lies within the nanometer scale. Their extreme dimension achieves extraordinary mechanical properties superior to other micro and macro additives. The introduction of nanotechnology to Civil Engineering utilizes low volume inclusions of nanomaterials to alter the properties of conventionally used bulk materials. Polymer Concrete (PC) where epoxy polymer binders replace cement binders, has become a common repair material among many other application and often can be considered an alternative to Portland cement concrete (PCC). PC is often used in bridge deck overlays, manholes, machine foundations and repairs. Its diverse chemical composition and …

Thin Film Thermal Deposition At Various Pressures, James Kela Yee Keen Grace

Senior Theses

This research was to verify the hypothesis that resistivity of metal's thin film deposited in a low-pressure environment is the same as its solid material. Thermal Evaporation is a thin film deposition technique in which metal inside a vacuum is evaporated, then deposited onto a surface. Higher quality metal films are deposited when the vacuum pressure is lower. At higher pressures, more air molecules are trapped within the layers of metal, thus increasing scattering sites and increasing the resistance. However, reaching a lower pressure requires more time and effort. In this research, films were deposited at various pressures and resistivities …

Investigation Into Effects Of Instability And Reactivity Of Hydride-Passivated Silicon Nanoparticles On Interband Photoluminescence, Christine Marie Radlinger

Dissertations and Theses

While silicon has long been utilized for its electronic properties, its use as an optical material has largely been limited due to the poor efficiency of interband transitions. However, discovery of visible photoluminescence (PL) from nanocrystalline silicon in 1990 triggered many ensuing research efforts to optimize PL from nanocrystalline silicon for optical applications. Currently, use of photoluminescent silicon nanoparticles (Si NPs) is commercially limited by: 1) the instability of the energy and intensity of the PL, and 2) the low quantum yield of interband PL from Si NPs.

Herein, red-emitting, hydrogen-passivated silicon nanoparticles (H-Si NPs) were synthesized by thermally-induced disproportionation …

Realizing Full Coverage Of Stable Perovskite Film By Modified Anti-Solvent Process, Long Ji, Ting Zhang, Yafei Wang, Peng Zhang, Detao Liu, Zhi David Chen, Shibin Li

Electrical and Computer Engineering Faculty Publications

Lead-free solution-processed solid-state photovoltaic devices based on formamidinium tin triiodide (FASnI₃) and cesium tin triiodide (CsSnI₃) perovskite semiconductor as the light harvester are reported. In this letter, we used solvent engineering and anti-solvent dripping method to fabricate perovskite films. SnCl₂ was used as an inhibitor of Sn⁴⁺ in FASnI₃ precursor solution. We obtained the best films under the function of toluene or chlorobenzene in anti-solvent dripping method and monitored the oxidation of FASnI₃ films in air. We chose SnF₂ as an additive of CsSnI₃ precursor solution to prevent the oxidation …

Find, Build, And Export Information For 3d Printing Of Your Favorite Molecules And Crystal Structures At Two Dedicated Websites, Paul R. Destefano, Peter Moeck

Student Research Symposium

As 3D printers require instructions, the Nano-Crystallography Group at Portland State University is creating two websites (http://nanocrystallography.org/3dconvert/ and http://nanocrystallography.research.pdx.edu/3d-print-files/convert/) where such instructions are created, interactively, for the atomic arrangements of virtually all known molecules and crystals.

We will prepare a "pipeline" into which crystallographic information enters from two curated open access crystallographic databases, is manipulated to create the desired 3D models, and then is exported in either STL format (the standard for monochrome 3D printing) or VRML/X3D (the ISO successor to STL). The two aforementioned databases are the North-American mirror of the Crystallography Open Database (http://nanocrystallography.org) …

Understanding Photovoltaic Properties Of Pbs Quantum Dot Solids Via Solution Contacting, Vitalii Dereviankin, Erik Johansson

Student Research Symposium

Photovoltaic (PV) devices based on PbS quantum dot (QD) solids demonstrate high photontoelectron conversion yields. However, record power conversion efficiency remain low, in part due to small photovoltages, which in turn are affected by both bulk and interfacial defects. Their relative impacts on limiting the photovoltaic performance of QD solids are not known. Interfacial defects can be formed when contacting a semiconductor and may dominate the semiconductor/metal or metaloxide junction properties. The objective of this study is to explore whether electrochemical contacting using liquid electrolytes provides means of contacting QD solids without introducing interfacial defects. We have initially focused on …

Total N-Nitrosamine Precursor Adsorption With Carbon Nanotubes: Elucidating Controlling Physiochemical Properties And Developing A Size-Resolved Precursor Surrogate, Erin Needham

Graduate Theses and Dissertations

As drinking water sources become increasingly impaired with nutrients and wastewater treatment plant (WWTP) effluent, formation of disinfection byproducts (DBPs) – such as trihalomethanes (THMs), dihaloacetonitriles (DHANs), and N-nitrosamines – during water treatment may also increase. N-nitrosamines may comprise the bulk of the chronic toxicity in treated drinking waters despite forming at low ng/L levels. This research seeks to elucidate physicochemical properties of carbon nanotubes (CNTs) for removal of DBP precursors, with an emphasis on total N-nitrosamines (TONO).

Batch experiments with CNTs were completed to assess adsorption of THM, DHAN, and TONO precursors; physiochemical properties of CNTs were quantified through …

Trihalomethane, Dihaloacetonitrile, And Total N-Nitrosamine Precursor Adsorption By Carbon Nanotubes: The Importance Of Surface Oxides And Pore Volume, Erin Needham

Graduate Theses and Dissertations

As drinking water sources become increasingly impaired, enhanced removal of natural organic matter (NOM) may be required to curb formation of disinfection byproducts (DBPs) upon chlor(am)ination. While carbon nanotubes (CNTs) can adsorb NOM, their properties for DBP precursor adsorption have not been elucidated. Nine types of CNTs were assessed for trihalomethane (THM), dihaloacetonitrile (DHAN), and total N-nitrosamine (TONO) precursor adsorption. Batch isotherm experiments were completed with lake water and, to simulate an impaired condition, effluent from a wastewater treatment plant (WWTP). Adsorption varied with CNT type and dose, with TONO precursors having the highest percent removals from WWTP effluent (up …

Infrared Energy Conversion In Plasmonic Fields At Two-Dimensional Semiconductors, Gregory Thomas Forcherio

Graduate Theses and Dissertations

Conversion of infrared energy within plasmonic fields at two-dimensional, semiconductive transition metal dichalcogenides (TMD) through plasmonic hot electron transport and nonlinear frequency mixing has important implications in next-generation optoelectronics. Drude-Lorentz theory and approximate discrete dipole (DDA) solutions to Maxwell’s equations guided metal nanoantenna design towards strong infrared localized surface plasmon resonance (LSPR). Excitation and damping dynamics of LSPR in heterostructures of noble metal nanoantennas and molybdenum- or tungsten-disulfide (MoS2; WS2) monolayers were examined by parallel synthesis of (i) DDA electrodynamic simulations and (ii) near-field electron energy loss (EELS) and far-field optical transmission UV-vis spectroscopic measurements. Susceptibility to second-order nonlinear frequency …

Molecular Dynamics Simulations Of Dna-Functionalized Nanoparticle Building Blocks On Gpus, Tyler Landon Fochtman

Graduate Theses and Dissertations

This thesis discusses massively parallel molecular dynamics simulations of nBLOCKs using graphical processing units. nBLOCKs are nanoscale building blocks composed of gold nanoparticles functionalized with single-stranded DNA molecules. To explore greater simulation time scales we implement our nBLOCK computational model as an extension to the coarse grain molecular simulator oxDNA. oxDNA is parameterized to match the thermodynamics of DNA strand hybridization as well as the mechanics of single stranded DNA and double stranded DNA. In addition to an in-depth review of our implementation details we also provide results of the model validation and performance tests. These validation and performance tests …

Characterization Of Coupled Gold Nanoparticles In A Sparsely Populated Square Lattice, Roy Truett French Iii

Graduate Theses and Dissertations

Metal nanoparticles deposited in regular arrays spaced at optical wavelengths support a resonance due to a coherent coupling between localized surface plasmon mode and lattice diffraction allowing for engineering of tunable devices for use in biological sensors, nanoantennae, and enhanced spectroscopy. Techniques such as electron beam lithography, focused ion beam lithography, nanosphere lithography, and nanoimprint lithography are used for fabrication but are limited by cost, device throughput, and small deposition. Polymer soft lithography and continuous dewetting of particles is a potentially viable alternative showing promise in all of those areas. This thesis developed the fabrication of a refined hydrophilic nanoimprinted …

A Study Of Dislocation Networks In Gasb On Gaas Using Transmission Electron Microscopy, Darryl M. Shima

Nanoscience and Microsystems ETDs

The growth of GaSb on GaAs is of interest for a variety of scientific and technological applications. Some evidence suggests that low threading dislocation density GaSb can be grown directly on GaAs through arrays of periodic edge misfit dislocations. However, significant conflicting data also exist. This work seeks to clarify the question through transmission electron microscopy analysis of GaSb grown on GaAs. The results of this work show that the single strategy of direct growth of GaSb on GaAs results in dislocation densities too high for devices. A secondary strategy of dislocation filtering layers is introduced to further reduce threading …

Editorial For The Special Issue On Micro/Nano-Chip Electrokinetics, Xiangchun Xuan, Shizhi Qian

Mechanical & Aerospace Engineering Faculty Publications

Micro/nanofluidics-based lab-on-a-chip devices have found extensive applications in the analysis of chemical and biological samples over the past two decades. Electrokinetics is the method of choice in these micro/nano-chips for transporting, manipulating and sensing various analyte species (e.g., ions, molecules, fluids and particles, etc.) [1,2]. This Special Issue in Micromachines is aimed to provide the recent development in the field of Micro/Nano-Chip Electrokinetics. It consists of 15 papers, which cover both fundamentals and applications, original research and reviews

Development And Degradation Analysis Of Novel Micro And Nanostructured Transition Metal Oxide (Tmo) Anodes For Aqueous Sodium Ion Batteries., Santanu Mukherjee

Electronic Theses and Dissertations

One of the primary motivations driving battery technology research is the need to develop cleaner and more efficient energy storage systems. The portable electronics industry has developed exponentially, especially over the last couple of decades and therefore the importance of efficient electrochemical energy storage systems cannot be overstated. Li-ion batteries have been the predominant rechargeable energy in use, however, they have their own particular drawbacks viz. flammability of the electrolyte, expensive mining of the Li metal etc. This is where the importance of Na-ion batteries lie. This research focuses on using existing transition metal oxides (TMOs) and tuning their crystal …

Optimization Of Reduced Graphene Oxide Deposition For Hydrogen Sensing Technologies, Matthew Pocta

Mechanical Engineering Undergraduate Honors Theses

Graphene is known to be a key material for improving the performance of hydrogen sensors. High electrical conductivity, maximum possible surface area with respect to volume, and high carrier mobility are a few of the properties that make graphene ideal for hydrogen sensing applications. The problem with utilizing graphene is the difficulty in depositing uniform, thin layers onto substrate surfaces. This study examines a new method of optimizing graphene deposition by utilizing an airbrush to deposit both graphene oxide (GO) and reduced graphene oxide (rGO) onto glass substrates. The number of depositions were varied among samples to study the effect …

Morphology Controlled Synthesis Of Copper Based Multimetallic Nanostructures And Their Electrocatalytic Properties For Methanol Oxidation Reaction, Leanne Elizabeth Mathurin

Graduate Theses and Dissertations

This research focuses on the development of shape-controlled synthesis of Cu NM, Cu-based bimetallic and trimetallic nanostructures, and their electrocatalytic properties for methanol oxidation reaction (MOR). Copper nanomaterials (Cu NM) with specific surface facets can tailor their catalytic activity. Understanding reagents responsible for Cu NM growth is important for morphology-controlled synthesis of the nanostructures. This research studies the halide influence on Cu NM growth and morphology in an oil-based synthesis. The morphology of the Cu NM varies with the halide type (i.e., Cl-, Br-, I-), and the halide concentration. Additionally, the type of Cu precursor also influenced the morphology of …