Mechanics of Materials Commons^™

Efficacy Of Softener For Enhancing Fatigue And Low-Temperature Performance Of Asphalt Binders With High Rap, Sumon Roy

Student Theses and Dissertations

The use of a higher percentage of reclaimed asphalt pavement (RAP) in asphalt concrete can lead to developing premature failure of asphalt pavements due to fatigue and/or low-temperature cracking. The incorporation of softening agents in asphalt binders can resolve these problems and enhance pavement durability. This study aims to evaluate the effectiveness of waste-based softening agents for enhancing the properties of asphalt mixes with high RAP contents. Waste cooking oil (WCO), and engine bottom oil (EBO) along with a commercial rejuvenator were investigated in this study. Three types of Performance Grade (PG) binders, each collected from two different sources, used …

Influence Of Supplementary Cementitious Material (Scm) On Concrete Durability (Drying Shrinkage And Alkali-Silica Reactivity), Raiyan Chowdhury

Student Theses and Dissertations

This study investigates the long-term durability of concrete by replacing cement (10%, 20%, and 30%) with four potential Supplementary Cementitious Material (SCMs), namely, Reclaimed Fly Ash (RFA), Ground Bottom Ash (GBA), Class F Fly Ash (FA), and Metakaolin® (MK). For long-term durability, drying shrinkage and alkali-silica reactivity (ASR) tests were performed along with workability (slump) and compressive strength tests. The FA and RFA demonstrated better workability compared to GBA, MK, and combined mixes (RFA-MK or GBA-MK). The GBA and RFA modified specimens exhibited better compressive strength than other SCMs. Modifying concrete mix with SCMs lowered the ASR expansion than the …

Recent Advances In Biosensors For Detection Of Covid-19 And Other Viruses, Shobhit K. Patel, Jaymit Surve, Juveriya Parmar, Kawsar Ahmed, Francis M. Bui, Fahad Ahmed Al-Zahrani

Department of Mechanical and Materials Engineering: Faculty Publications

This century has introduced very deadly, dangerous, and infectious diseases to humankind such as the influenza virus, Ebola virus, Zika virus, and the most infectious SARS-CoV-2 commonly known as COVID-19 and have caused epidemics and pandemics across the globe. For some of these diseases, proper medications, and vaccinations are missing and the early detection of these viruses will be critical to saving the patients. And even the vaccines are available for COVID-19, the new variants of COVID-19 such as Delta, and Omicron are spreading at large. The available virus detection techniques take a long time, are costly, and complex and …

Rational Design Of Flexible And Stretchable Electronics Based On 3d Printing, Yuanhang Yang

Theses and Dissertations

Flexible and stretchable electronics have been considered as the key component for the next generation of flexible devices. There are many approaches to prepare the devices, such as dip coating, spin coating, Mayer bar coating, filtration and transfer, and printing, etc. The effectiveness of these methods has been proven, but some drawbacks cannot be ignored, such as lacking pattern control, labor consuming, requiring complex pretreatment, wasting conductive materials, etc.

In this investigation, we propose to adopt 3D printing technology to design flexible and stretchable electronics. The objective is to rationally design flexible and stretchable sensors, simplify the preparation process, form …

Visualization And Validation Of Twin Nucleation And Early-Stage Growth In Magnesium, Lin Jiang, Mingyu Gong, Jian Wang, Zhiliang Pan, Xin Wang, Dalong Zhang, Y. Morris Wang, Jim Ciston, Andrew M. Minor, Mingjie Xu, Xiaoqing Pan, Timothy J. Rupert, Subhash Mahajan, Enrique J. Lavernia, Irene J. Beyerlein, Julie M. Schoenung

Department of Mechanical and Materials Engineering: Faculty Publications

The abrupt occurrence of twinning when Mg is deformed leads to a highly anisotropic response, making it too unreliable for structural use and too unpredictable for observation. Here, we describe an in-situ transmission electron microscopy experiment on Mg crystals with strategically designed geometries for visualization of a long-proposed but unverified twinning mechanism. Combining with atomistic simulations and topological analysis, we conclude that twin nucleation occurs through a pure-shuffle mechanism that requires prismatic-basal transformations. Also, we verified a crystal geometry dependent twin growth mechanism, that is the early-stage growth associated with instability of plasticity flow, which can be dominated either by …

Microscale Transverse Compression Modeling: A Comparative Study Of The Analytical Mac/Gmc Methods To Experimental Results, Emily Zeitunian

Dissertations, Master's Theses and Master's Reports

Composite materials require a multi-scale approach to fully understand its behavior. At the micro level, material behavior analysis is conducted most often using numerical or analytical approaches. These models, however, require validation from experimental data to ensure material predictions are accurate. This study compares a semi-analytical micromechanical analysis tool, MAC/GMC, to experimental results of in-situ microscale transverse compression testing conducted at AFRL facilities. Effective properties, stress-strain curves, stress and strain fields, and damage predictions are compared with experimental outputs. Both generalized method of cells (GMC) and high-fidelity generalized method of cells (HFGMC) theories implemented within MAC/GMC show results that agree …

A Computational Exploration Of The Scandate Cathode Surface, Shankar Miller-Murthy

Theses and Dissertations--Chemical and Materials Engineering

The exact surface configuration of scandate cathodes has been a point of contention for the materials community for a long time. Without proper understanding of it and the related structures and emission mechanisms, scandate cathodes remain patchy and unreliable emitters. Thus, density functional theory techniques were applied to various potential surface arrangements and found that there are several low-energy surfaces with low work functions that incorporate a scandium interlayer between tungsten and oxygen or otherwise have a scandium-on-tungsten structure. Furthermore, it was discovered that adding a monolayer of scandium directly to a tungsten surface is surprisingly favorable, thermodynamically. While none …

Lateral-Torsional Instability And Biaxial Bending Of Imperfect Frp I-Beams, Jodi Knorowski, Stella B. Bondi, Zia Razzaq

Civil & Environmental Engineering Faculty Publications

This paper presents the outcome of a theoretical and experimental study of the behavior of Fiber Reinforced Polymer (FRP) I-beams exposed to lateral-torsional instability or when subjected to biaxial bending. Laboratory experiments involved the application of vertical and horizontal static loads to a 4 x 4 x ¼ in. I-beam with various lengths and the resulting deflections were recorded. Governing biaxial flexure and torsion differential equations were modified to account for the presence of initial imperfections and subsequently solved using a central finite-difference scheme. The theoretical predictions of the beam behavior were found to be in good agreement with what …

Adjust-A-Ramp, Taylor Sharrits, Courtney Banks, Emily Beck, Jazmin Buenrostro

Williams Honors College, Honors Research Projects

Adjust-A-Ramp is a portable ramp designed to ensure the safety of consumers and prevention of damage to cars, specifically towards low profile cars. A low-profile vehicle includes any vehicle that has a clearance off the ground of 6.5 inches or less. Advantages of low-profile vehicles include improved handling, better braking, increased fuel efficiency, increased stability, and an overall luxury aesthetic. The reduced tire size increases grip on smooth surfaces with better wheel response, creating a fast, more efficient ride. The simple tire tread patterns and the stiff sidewalls allow for lower rolling resistance which increases fuel economy. The Adjust-A-Ramp can …

Recycled Printer Filament, Charlotte Hyland, Troy D. Molinar

Williams Honors College, Honors Research Projects

The purpose of this research is to examine the effects of recycling PLA filament for 3D printing on its material properties. After examining these effects, PLA and carbon fiber additives were mixed with recycled PLA pellets in different ratios to attempt to regain material properties lost in the recycling process. To complete these findings, an experiment was design and executed.

The research found that tensile strength during multiple iterations of recycling remained mostly unaffected, however, the strain degraded exponentially. In the PLA additive study, high ratios of PLA additive were able to increase the strength and strain properties of the …

Grinding And Super-Finishing Test Machine Project, Michael Simon

Williams Honors College, Honors Research Projects

A research project in The University of Akron to study grinding and super-finishing of silicon nitride ceramic was initiated by Dr. Siamak Farhad and sponsored by the Timken Company, with the assistance of undergraduate students Michael Simon, Ryan Hosso and Mathew Rozmajzl. The study required analysis of forces and scratches generated during grinding processes of silicon nitride samples. A testing assembly was designed and constructed to record the forces generated during grinding and super-finishing of silicon nitride samples in a computer-numerical-control machine. Silicon nitride samples were subjected to desired grinding and super-finishing operations and all forces generated during the process …

Type Iii And Iv Deformation Twins In Minerals And Metals, John P. Hirth, Greg Hirth, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Type IV twins are defined and shown to exist in triclinic crystal systems, as well as in some monoclinic and trigonal systems. Here, we focus on Pericline twins in triclinic plagioclase as an example. Type IV twins are associated with the irrationality of one of the twinning elements that is rational for a type II twin. The formation of type IV twins is accomplished through the shear on a K2 plane produced by the motion of twinning disconnections on a K1 plane, followed by rotational partitioning. The same systems where type IV twins are present also have type III twins …

Emissivity Prediction Of Functionalized Surfaces Using Artificial Intelligence, Greg Acosta, Andrew Reicks, Miguel Moreno, Alireza Borjali, Craig Zuhlke, Mohammad Ghashami

Department of Mechanical and Materials Engineering: Faculty Publications

Tuning surface emissivity has been of great interest in thermal radiation applications, such as thermophotovoltaics and passive radiative cooling. As a low-cost and scalable technique for manufacturing surfaces with desired emissivities, femtosecond laser surface processing (FLSP) has recently drawn enormous attention. Despite the versatility offered by FLSP, there is a knowledge gap in accurately predicting the outcome emissivity prior to fabrication. In this work, we demonstrate the immense advantage of employing artificial intelligence (AI) techniques to predict the emissivity of complex surfaces. For this aim, we used FLSP to fabricate 116 different aluminum samples. A comprehensive dataset was established by …

Construction Of A Peridynamic Model For Viscous Flow, Jiangming Zhao, Adam Larios, Florin Bobaru Ph.D.

Department of Mechanical and Materials Engineering: Faculty Publications

We derive the Eulerian formulation for a peridynamic (PD) model of Newtonian viscous flow starting from fundamental principles: conservation of mass and momentum. This formulation is different from models for viscous flow that utilize the so-called “peridynamic differential operator” with the classical Navier- Stokes equations. We show that the classical continuity equation is a limiting case of the PD one, assuming certain smoothness conditions. The PD model for viscous flow is calibrated to the classical Navier-Stokes equations by enforcing linear consistency for the viscous stress term. Couette and Poiseuille flows, and incompressible fluid flow past a regular lattice of cylinders …

Ultrathin Coding Metasurface For Underwater Wave Focusing, Branching And Self-Bending Generation With One Single Actuator, Lixie Song, Zhong Chen, Mehrdad Negahban, Lei Liang, Zheng Li, Zheng Wu

Department of Mechanical and Materials Engineering: Faculty Publications

A novel metasurface is proposed that aims to generate underwater acoustic waves with various functions by only one actuator. Each metasurface unit consists of an air cavity sandwiched on one side by a vibration plate and connecting rubber supports. By properly selecting the ratio of the plate to unit lengths, a phase shift of π can be attained to constitute a binary coding metasurface. Three demonstrations, including focusing, branching and self-bending waves, are chosen to validate the functionality of the design. The design is also shown to work over a wide frequency range through changing the ratio. In addition, the …

Machine Learning Assisted Metamaterial‑Based Reconfigurable Antenna For Low‑Cost Portable Electronic Devices, Shobhit K. Patel, Jaymit Surve, Vijay Katkar, Juveriya Parmar

Department of Mechanical and Materials Engineering: Faculty Publications

Antenna design has evolved from bulkier to small portable designs but there is a need for smarter antenna design using machine learning algorithms that can meet today’s high growing demand for smart and fast devices. Here in this research, main focus is on developing smart antenna design using machine learning applicable in 5G mobile applications and portable Wi-Fi, Wi-MAX, and WLAN applications. Our design is based on the metamaterial concept where the patch is truncated and etched with a split ring resonator (SRR). The high gain requirement is met by adding metamaterial superstrates having thin wires (TW) and SRRs. The …

Symmetric Or Asymmetric Glide Resistance To Twinning Disconnection?, Mingyu Gong, Houyu Ma, Kunming Yang, Yue Liu, Jian-Feng Nie, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Successive gliding of twinning disconnections (TDs) creates three-dimensional twins in parent crystal and accommodates shear deformation. It is generally recognized that TD is subject to the same Peierls stress as it glides forward or backward because of its dislocation character and the twofold rotation symmetry of the twin plane. Based on atomistic simulations, we demonstrate that the glide of TDs may be subject to a symmetric or asymmetric resistance corresponding to step character, symmetric resistance for A/A type steps but asymmetric resistance for A/B type steps, where A and B represent crystallographic planes in twin and matrix. Furthermore, we experimentally …

Recent Advances In Biosensors For Detection Of Covid-19 And Other Viruses, Shobhit K. Patel, Jaymit Surve, Juveriya Parmar, Kawsar Ahmed, Francis M. Bui, Fahad Ahmed Al-Zahrani

Department of Mechanical and Materials Engineering: Faculty Publications

This century has introduced very deadly, dangerous, and infectious diseases to humankind such as the influenza virus, Ebola virus, Zika virus, and the most infectious SARS-CoV-2 commonly known as COVID-19 and have caused epidemics and pandemics across the globe. For some of these diseases, proper medications, and vaccinations are missing and the early detection of these viruses will be critical to saving the patients. And even the vaccines are available for COVID-19, the new variants of COVID-19 such as Delta, and Omicron are spreading at large. The available virus detection techniques take a long time, are costly, and complex and …

A Robot-Assisted Acoustofluidic End Effector, Jan Durrer, Prajwal Agrawal, Ali Ozgul, Stephen C.F. Neuhauss, Nitesh Nama, Daniel Ahmed

Department of Mechanical and Materials Engineering: Faculty Publications

Liquid manipulation is the foundation of most laboratory processes. For macroscale liquid handling, both do-it-yourself and commercial robotic systems are available; however, for microscale, reagents are expensive and sample preparation is difficult. Over the last decade, lab-on-a-chip (LOC) systems have come to serve for microscale liquid manipulation; however, lacking automation andmulti-functionality. Despite their potential synergies, each has grown separately and no suitable interface yet exists to link macro-level robotics with micro-level LOC or microfluidic devices. Here, we present a robot-assisted acoustofluidic end effector (RAEE) system, comprising a robotic arm and an acoustofluidic end effector, that combines robotics and microfluidic functionalities.We …

Exploring The Effects Of Chip Flexibility On The Behavior Of Standing Seam Diaphragms To Brace Cold Formed Steel Purlins, Michael W. Seek

Engineering Technology Faculty Publications

Cold-formed steel C- and Z-shaped purlins in standing seam roof systems rely on the diaphragm action provided by the panels to restrain lateral movements and thus increase the load carrying capacity the purlins. The clip connection between the purlin and the panel has inherent and sometimes intentional flexibility designed to accommodate thermal deformations. The lateral deformation behavior of standing seam systems supported by Zees is highly nonlinear and this behavior is not well understood. The flexibility has major implications on the transfer of diaphragm forces throughout these systems and simplified models often grossly overpredict the demands on the diaphragm and …

Cold-Formed Steel Strength Predictions For Torsion, Yu Xia, Robert S. Glauz, Benjamin W. Schafer, Michael Seek, Hannah B. Blum

Engineering Technology Faculty Publications

Locally slender open cross-section members are susceptible to significant twisting and high warping torsion stresses. Torsion considerations are complicated by whether it is derived as a first-order effect from loading or a second-order effect from instability. Previous direct torsion experiments on lipped channels have shown significant inelastic reserve in limited cases. The current design for combined bending and torsion interaction has some limitations, including only considering the first yield in torsion and ignoring the cross-section slenderness in torsion. A parametric study is conducted to predict the torsion capacity in locally slender cross-sections. Shell finite element models of lipped Cee and …

Design Methodology For Input Shapers Using Genetic Algorithms In Flexible Nonlinear Systems, Mohab Adel Hakim Meshreki

Archived Theses and Dissertations

No abstract provided.

Smooth Muscle Cells Affect Differential Nanoparticle Accumulation In Disturbed Blood Flow-Induced Murine Atherosclerosis, Hunter Miller, Morgan A. Schake, Badrul Alam Bony, Evan T. Curtis, Conner C. Gee, Ian Mccue, Thomas J. Ripperda Jr., Yiannis S. Chatzizisis, Forrest Kievit, Ryan M. Pedrigi

Department of Mechanical and Materials Engineering: Faculty Publications

Atherosclerosis is a lipid-driven chronic inflammatory disease that leads to the formation of plaques in the inner lining of arteries. Plaques form over a range of phenotypes, the most severe of which is vulnerable to rupture and causes most of the clinically significant events. In this study, we evaluated the efficacy of nanoparticles (NPs) to differentiate between two plaque phenotypes based on accumulation kinetics in a mouse model of atherosclerosis. This model uses a perivascular cuff to induce two regions of disturbed wall shear stress (WSS) on the inner lining of the instrumented artery, low (upstream) and multidirectional (downstream), which, …

Microfabricated Platforms To Investigate Cell Mechanical Properties, Amir M. Esfahani, Grayson Minnick, Jordan Rosenbohm, Haiwei Zhai, Xiaowei Jin, Bahareh Tajvidi Safa, Justin Brooks, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

Mechanical stimulation has been imposed on living cells using several approaches. Most early investigations were conducted on groups of cells, utilizing techniques such as substrate deformation and flow-induced shear. To investigate the properties of cells individually, many conventional techniques were utilized, such as AFM, optical traps/optical tweezers, magnetic beads, and micropipette aspiration. In specific mechanical interrogations, microelectro- mechanical systems (MEMS) have been designed to probe single cells in different interrogation modes. To exert loads on the cells, these devices often comprise piezo-electric driven actuators that attach directly to the cell or move a structure on which cells are attached. Uniaxial …

Rational Design Of Multifunctional Nanocatalysts For Environmental Remediation And Energy Conversion Technologies, Md Ariful Ahsan

Open Access Theses & Dissertations

The discovery of efficient and sustainable carbon-based nanotechnologies to solve both the scarcity of drinking water and global energy crisis has become a paramount task in the last decades. Owed to the fast population growth and industrialization of the modern society, access to potable water and clean energy technologies is becoming very hard around the globe. Water pollutants have become a serious threat to the environment and ecology because of their toxic nature. Parallelly, the current hydrocarbon-based fuel industries are generating high levels of contamination across the planet, making imperative the development of cleaner energy technologies. In this regard, the …

Thermodynamic Modeling Of Aqueous Fe-Cu-As-Sb-Bi-H2so4 Solutions And Its Application For Redox Potential Determination In Copper Electrorefining From 25°C To 70°C, Yongteng Dong

Open Access Theses & Dissertations

Impurity elements in copper electrorefining (ER) electrolyte have been becoming a crucial issue on purity of copper cathode. The objective of this doctoral research is to develop a speciation model to understand impurity behavior in aqueous ER solutions.

A thermodynamic model of Fe(II)-Fe(III)-Cu(II)-H2SO4-H2O system is developed and shown to reliably simulate the species distribution in industrial copper electrorefining electrolyte from 25°C to 70°C. The previously developed model of Fe(II)-Fe(III)-H2SO4-H2O system under leaching conditions was first evaluated. It has proved that its applicability can be extended to much higher acid concentration (185 g/L) and high amount of copper (40-50 g/L). Cu(II) …

Microstructure And Hardness Comparison Of Inconel 625 Alloy Of Various Additive Manufacturing Processes Following Heat Treatments, Ariel Gamon

Open Access Theses & Dissertations

This research study presents experimental examples of as-built microstructures and associated microindentation hardnesses (HV) for a variety of metal additive manufacturing (AM) methods for Inconel 625 alloy. Cold spray (CS), laser powder bed fusion (L-PBF), wire arc additive manufacturing (WAAM), electron beam directed energy deposition (EB-DED), laser hot wire (LHW), binder jetting (BJT), and laser power directed energy deposition (LP-DED), laser wire directed energy deposition (LW-DED) and electron beam melting (EBM) were among the techniques employed. Microstructures varied from impact-bonded, flattened grains containing microdendrites and dislocations with a microindentation hardness of HV 590 for cold spray to large, equiaxed grains …

Understanding The Chemical Structures Of Polydopamine, Deborah Takyibea Okyere

Graduate Theses and Dissertations

Polydopamine (PDA) is described as a bioinspired polymer produced by a method involving the chemical oxidation of dopamine in a pH-dependent medium. It has been used for the functionalization of nanomaterials in diverse applications including drug delivery and biosensing because of its strong adhesiveness, functionality is easily modified, and biocompatibility with mammalian cells and tissues. The polymerization process is believed to be initiated by the autoxidation of dopamine to dopaminequinone. However, the repeating units, as well as the final structure of PDA, are not well understood. Hence, this work focuses on the characterizations of the PDA structures during formation and …

Phase Transformation And Strain Hardening Mechanisms In Advanced Engineering Steels, Hangyu Dong

Open Access Theses & Dissertations

Strain hardening and associated deformation mechanisms play a determining role in the performance of metallic materials. The objective of the doctoral research was to explore and fundamentally understand the strain hardening mechanisms in the next generation of advanced engineering steels. Two main work hardening mechanisms, notably, twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP)) were identified that governed strength and ductility. In the nanograined austenitic steel with high strength-high ductility combination, processed by the novel phase reversion concept, twinning-induced plasticity (TWIP) was the governing deformation mechanism and contributed to good ductility. In striking contrast, transformation-induced plasticity (TRIP) was the deformation mechanism …

Synthesis And Characterization Of Tin (Sn) Incorporated Ga2o3, Guillermo Nicolas Gutierrez

Open Access Theses & Dissertations

In this work, we report on the synthesis, characterization of tin (Sn) incorporated gallium oxide Ga2O3 compounds, also included in this work is the effect of tin concentration related to the optical and electrochemical properties. The Sn incorporation into Ga2O3 creates a significant reduction in the bandgap and causes a nonlinear optical activity as the concentration varies. Substantial investigation performed to the structure, phase, and morphology of the mixed compounds governed by the stoichiometry equation Ga2−2xSnxO3-ɗ indicates that the Sn incorporation from 0.00 ≤ x ≤ 0.30 has a significant effect on these properties. To synthesize the Ga-Sn-O compounds a …