Mechanics of Materials Commons^™

Effect Of Blank Moisture Content On Forming Behaviour And Mechanical Properties Of Paperboard Tray Packages, Arvo Niini, Lena Berthold, Tobias Müller, Panu Tanninen, Jens-Peter Majschak, Juha Varis, Ville Leminen

Journal of Applied Packaging Research

Tray blanks were moisturised to study the effect of different blank moisture content levels on forming behaviour and mechanical properties of paperboard tray packages. The blank moisturisation was done by spraying water to the blanks before their three-dimensional (3D) forming. The trays were 3D formed by press forming or deep drawing. Visual quality and punch force values were used as indicators to evaluate the forming behaviour of the trays. The mechanical properties of the trays were investigated with compression, torsion, and storing tests. A high blank moisture content reduced the punch force, and the elevated blank moisture was connected to …

Freespan Analysis For Subsea Pipeline Integrity Management Strategy, Nurul Hadi, Muhammad Helmi, Edo Cathaputra, Dedi Priadi, Donanta Dhaneswara

Journal of Materials Exploration and Findings

Abstract. Over a rough seabed or on seabed subject to scour, freespans can occur when contact between a subsea pipeline and the seabed is lost over an acceptable distance. When this exceeds the allowable freespan length, design stresses can be exceeded, and a vortex induced vibration (VIV) response can be initiated, resulting in the risk of fatigue failure. If this is not predicted and controlled properly, it will affect pipeline integrity, leading to expensive rectification and intervention work. Freespan analysis consisted primarily of a screening check in which the as-found freespans from Remotely Operated Vehicle (ROV) or multibeam Side …

Locally Resonant Metasurface For Low-Frequency Transmissive Underwater Acoustic Waves, Zhong Chen, Shenghong Guan, Qiang Xie, Zheng Li, Zhongmei Gao, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction: Acoustic metasurfaces for underwater wave manipulation have great potential use, but the strong solid-fluid interaction caused by impedance closeness between the structure and water brings design difficulty, especially in the low-frequency range.

Methods: Here a locally resonant metasurface for transmissive underwater acoustic waves is proposed using finite element method for which each metasurface unit consists of one channel and three subunits. Each subunit has one plate and two rubber spacers to form a resonator. By changing the height ratio of the plate over the subunit, arbitrary phase shifts within the full 2π coverage can be obtained at …

An Efficient And Low-Cost Method To Create High-Density Nitrogen-Vacancy Centers In Cvd Diamond For Sensing Applications., Prem Bahadur Karki, Rupak Timalsina, Mohammadjavad Dowran, Ayodimeji E. Aregbesola, Abdelghani Laraoui, Kapildeb Ambal

Department of Mechanical and Materials Engineering: Faculty Publications

The negatively charged Nitrogen-Vacancy (NV^-) center in diamond is one of the most versatile and robust quantum sensors suitable for quantum technologies, including magnetic field and temperature sensors. For precision sensing applications, densely packed NV^- centers within a small volume are preferable due to benefiting from 1/√𝑁 sensitivity enhancement (N is the number of sensing NV centers) and efficient excitation of NV centers. However, methods for quickly and efficiently forming high concentrations of NV^- centers are in development stage. We report an efficient, low-cost method for creating high-density NV^- centers production from a relatively …

Correction: Nanoscale Imaging Of Antiferromagnetic Domains In Epitaxial Films Of Cr2o3 Via Scanning Diamond Magnetic Probe Microscopy, Adam Erickson, Syed Qamar Abbas Shah, Ather Mahmood, Ilja Fescenko, Rupak Timalsina, Christian H. Binek, Abdelghani Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

Correction for ‘Nanoscale imaging of antiferromagnetic domains in epitaxial films of Cr2O3 via scanning diamond magnetic probe microscopy’ by Adam Erickson et al., RSC Adv., 2023, 13, 178–185, https:// doi.org/10.1039/D2RA06440E

Traversing With Quantitative Fidelity Through The Glass Transition Of Amorphous Polymers: Modeling The Thermodynamic Dilatational Flow Of Polycarbonate, Mehrdad Negahban, Wenlong Li, Jean-Marc Saiter, Laurent Delbreilh, Kyle Strabala, Zheng Li

Department of Mechanical and Materials Engineering: Faculty Publications

We follow the assumption that the dilatational response of glassy polymers can be characterized by a back-stress type analog that includes a thermal expansion for each elastic component, and with a viscosity that is dependent on the expansion of the elastic back stress component. To this, we add the assumption of an unloaded equilibrium temperature that correlates to the past processing through the viscous flow. After setting this in a thermodynamically consistent structure, the elastic, elastic backstress, thermal expansion, back-stress thermal expansion, heat capacity and viscous damping are evaluated using existing experiments for the response of polycarbonate over the glassy …

Peridynamic Simulation Of Elastic Wave Propagation By Applying The Boundary Conditions With The Surface Node Method, Francesco Scabbia, Mirco Zaccariotto, Ugo Galvanetto, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

Peridynamics is a novel nonlocal theory able to deal with discontinuities, such as crack initiation and propagation. Near the boundaries, due to the incomplete nonlocal region, the peridynamic surface effect is present, and its reduction relies on using a very small horizon, which ends up being expensive computationally. Furthermore, the imposition of nonlocal boundary conditions in a local way is often required. The surface node method has been proposed to solve both the aforementioned issues, providing enhanced accuracy near the boundaries of the body. This method has been verified in the cases of quasi-static elastic problems and diffusion problems evolving …

Post-Weld Heat Treatment Effects On Microstructure, Crystal Structure, And Mechanical Properties Of Donor Stir–Assisted Friction Stir Welding Material Of Aa6061-T6 Alloy, Aiman H. Al-Allaq, Manish Ojha, Yousuf S. Mohammed, Srinivasa N. Bhukya, Zhenhua Wu, Abdelmageed A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

Friction stir welding (FSW) technology combines heat input from friction and extreme plastic deformation to produce high-quality joints in aluminum and other alloy systems. This necessitates examining the final welded joint’s mechanical and structural properties. Post-weld heat-treated AA6061-T6 alloy that resulted from the application of a Cu donor stir–assisted (CDSA) friction stir welding (FSW) material was examined for crystal structure and mechanical properties. CDSA FSW samples were tested at a constant tool rotational speed of 1400 rpm and a welding translational speed of 1 mm/s. CDSA samples of 20% and 60% thickness of the AA6061-T6 base alloy were selected to …

Attrition Study Of Copper-Supplemented Iron-Based Oxygen Carrier For Chemical Looping Combustion, Neng Huang

Theses and Dissertations--Mechanical and Aerospace Engineering

Chemical looping combustion (CLC) is a promising technology that can mitigate the carbon emissions for power generation. The cost of oxygen carriers (OCs) impedes the scale up of CLC. Compared to synthetic iron-based OCs, red mud (RM), an abundant iron-based solid waste from industry, is a cost-effective choice due to its intrinsic inclusion of both inert and catalytic phases that are crucial for CLC. It was anticipated that the addition of copper oxide to RM using a mechanical mixing method that can be easily scaled up would enhance both reactivity and oxygen transport capacity (OTC), and the heat of reaction …

Elastic Properties Of The Non-Mixing Copper Donor Assisted Material In Friction Stir Welding Of Aluminum Alloys Using Nanoindentation, M. Ojha, A. H. Al-Allaq, Y. S. Mohammed, S. N. Bhukya, Z. Wu, A. A. Elmustafa

Mechanical & Aerospace Engineering Faculty Publications

Friction stir welding of high-strength materials such as steels is the impeded by the lack of the vast heat input needed to start the process. Contact friction is considered the most dominant source of heat generation for FSW steels which tends to cause severe wear conditions of the tool hear. To relieve the extreme wear conditions that occur on the tool heads because of FSW steels, we introduce the non-mixing Cu donor stir material to friction stir welding of aluminum alloys. The elastic properties of the Cu donor assisted friction stir welded aluminum alloys are measured using nanoindentation. The hardness …

Cold-Formed Steel Strength Predictions For Combined Bending And Torsion, Yu Xia, Robert S. Glauz, Benjamin W. Schafer, Michael Seek, Hannah B. Blum

Engineering Technology Faculty Publications

Locally slender cross-section members, such as cold-formed steel Cee and Zee sections, are susceptible to significant twisting and high warping torsion stresses. Torsion considerations are complicated by whether it is derived as a first-order effect from loading or a second-order effect from instability. The current design for combined bending and torsion interaction has some limitations, including only considering the first yield in torsion and ignoring the cross-section slenderness in torsion. Previous work has derived a simple uniform equation to predict the bimoment capacity and two bimoment strength curves for local and distortional buckling under torsion only. This work is extended …

Dome Tester, Clark Bates, Nikolas M. Kulin

Williams Honors College, Honors Research Projects

We are reconfiguring and modifying the previously built dome tester to be more user friendly and mechanically applicable. This has a long-term goal of being a usable teaching tool for manufacturing education within the college of engineering and polymer sciences. The dome tester pushes a metal dome into a clamped sheet of metal to test its forming limits and where necking occurs. We have implemented a better method of viewing the sheet sample as it is being deformed, and improved measuring methods for the distance a sample is deformed. By introducing these changes in conjunction with improved documentation of the …

Establishing The Foundation To Robotize Complex Welding Processes Through Learning From Human Welders Based On Deep Learning Techniques, Rui Yu

Theses and Dissertations--Electrical and Computer Engineering

As the demand for customized, efficient, and high-quality production increases, traditional manufacturing processes are transforming into smart manufacturing with the aid of advancements in information technology, such as cyber-physical systems (CPS), the Internet of Things (IoT), big data, and artificial intelligence (AI). The key requirement for integration with these advanced information technologies is to digitize manufacturing processes to enable analysis, control, and interaction with other digitized components. The integration of deep learning algorithm and massive industrial data will be critical components in realizing this process, leading to enhanced manufacturing in the Future of Work at the Human-Technology Frontier (FW-HTF).

This …

Application Of Multi-Scale Computational Techniques To Complex Materials Systems, Mujan N. Seif

Theses and Dissertations--Chemical and Materials Engineering

The applications of computational materials science are ever-increasing, connecting fields far beyond traditional subfields in materials science. This dissertation demonstrates the broad scope of multi-scale computational techniques by investigating multiple unrelated complex material systems, namely scandate thermionic cathodes and the metallic foam component of micrometeoroid and orbital debris (MMOD) shielding. Sc-containing "scandate" cathodes have been widely reported to exhibit superior properties compared to previous thermionic cathodes; however, knowledge of their precise operating mechanism remains elusive. Here, quantum mechanical calculations were utilized to map the phase space of stable, highly-faceted and chemically-complex W nanoparticles, accounting for both finite temperature and chemical …

Solid-State Electrolytes For Long Duration Molten Sodium Batteries, Ryan C. Hill

Theses and Dissertations--Chemical and Materials Engineering

Rechargeable batteries have become a staple of modern society, driving the development and expansion of portable electronics and electric vehicles. The long lifetime and high energy density provided by batteries have made them excellent candidates for use in the emerging field of long duration, grid-scale energy storage. However, traditional battery chemistries, such as Li-ion, are not an ideal solution for grid-scale storage, due to high-cost raw materials that are often sourced from volatile markets. Sodium-based batteries are a promising alternative for long duration storage, owing to the domestic abundance of raw materials and energy densities that nearly rival that of …

Development Of Inconel 718f And Inconel 718e Powders For Parts Manufacturing Utilizing Binder Jet Three-Dimensional Printing And Compressed Pellet Methods, Duncan Eric Manor Ii

Graduate Theses, Dissertations, and Problem Reports (ETD)

Alloy Inconel 718 is a Ni based superalloy used for high temperature applications including turbine blades, turbocharger rotors and nuclear reactors. Inconel 718 is a popular commercial atomized powder that has limitations in performance for use in additive manufacturing applications due to poor part quality and efficiency of current fabrication methods. Developing new compositions and additive manufacturing (AM) methodologies of IN718 is critical to improve the quality and the efficiency of IN718 parts manufacturing. Developing new additive manufacturing methodology that produces higher quality parts made of IN718 as compared to current methods has the potential to greatly impact industry, academia, …

Phase-Averaged, Frequency Dependence Of Jet Dynamics In A Scaled Up Vocal Fold Model With Full And Incomplete Closure, Nathaniel Wei, Abigail Haworth, Hunter Ringenberg, Michael Krane, Timothy Wei

Department of Mechanical and Materials Engineering: Faculty Publications

This study focuses on frequency dependence effects on glottal jet dynamics with a focus on the physiological condition in which the vocal folds do not fully close. Incomplete closure occurs naturally in children and adult females. But there are also pathological conditions that can be problematic. Experiments were conducted using a 10× scaled-up model in a free surface water tunnel. Two-dimensional vocal fold models with semicircular medial surfaces were stepper motor driven inside a square duct with constant opening and closing speeds. Cases with complete vocal fold closure and incomplete closure to only 15% of the maximum gap were examined. …

Sars-Cov-2 Detecting Rapid Metasurface-Based Sensor, Shobhit K. Patel, Jaymit Surve, Juveriya Parmar, Khaled Aliqab, Meshari Alsharari, Ammar Armghan

Department of Mechanical and Materials Engineering: Faculty Publications

We have proposed a novel approach to detect COVID-19 by detecting the ethyl butanoate which high volume ratio is present in the exhaled breath of a COVID-19 infected person. We have employed a refractive index sensor (RIS) with the help of a metasurface-based slotted T-shape perfect absorber that can detect ethyl butanoate present in exhaled breath of COVID-19 infected person with high sensitivity and in-process SARS-CoV-2. The optimized structure of the sensor is obtained by varying several structure parameters including structure length and thickness, slotted T-shape resonator length, width, and thickness. Sensor’s performance is evaluated based on numerous factors comprising …

Nanoscale Imaging Of Antiferromagnetic Domains In Epitaxial Films Of Cr2O3 Via Scanning Diamond Magnetic Probe Microscopy, Adam Erickson, Syed Qamar Abbas Shah, Ather Mahmood, Ilja Fescenko, Christian H. Binek, Adbelghani Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

We report direct imaging of boundary magnetization associated with antiferromagnetic domains in magnetoelectric epitaxial Cr₂O₃ thin films using diamond nitrogen vacancy microscopy. We found a correlation between magnetic domain size and structural grain size which we associate with the domain formation process. We performed field cooling, i.e., cooling from above to below the Néel temperature in the presence of a magnetic field, which resulted in the selection of one of the two otherwise degenerate 180° domains. Lifting of such a degeneracy is achievable with a magnetic field alone due to the Zeeman energy of a weak …

Sulfonated Styrene Grafted Sebs/Abs Made By Additive Manufacturing For Ion Exchange Applications, Avianna Elaine Gallegos

Open Access Theses & Dissertations

An interpenetrating polymer network (IPN) for cation exchange applications was synthesized from a blend of styrene-ethylene/butylene-styrene (SEBS) and acrylonitrile butadiene styrene (ABS), which was 3D printed, grafted with crosslinked polystyrene (PS), and sulfonated. A method for styrene grafting was applied to reduce the damage to polymer phases caused by the sulfonation reaction. Styrene and divinylbenzene monomers were introduced to the IPN and induced with heat treatment to polymerize in situ. The graft copolymerization reaction was enhanced with varying quantities of benzoyl peroxide as a chemical initiator. The samples were subsequently sulfonated with chlorosulfonic acid in dichloroethane and functionalized for ion …

A Comparative Evaluation Of Oxidation And Combustion Phenomena In Ti-6al-4v Exposed To Earth Re-Entry And Arc-Jet Test Environments, Arlene Smith

Open Access Theses & Dissertations

The Ti-6Al-4V alloy is widely used in aerospace applications for its beneficial combination of properties. However, this alloy has high solubility for oxygen and thus a high reactivity. Recovered data contained within the Columbia artifacts suggests that this alloy underwent an accelerated degradation and combustion reaction when exposed to the high enthalpy, low-pressure surroundings experienced during reentry into Earth's atmosphere. Arc-jet testing has provided a simulated aerothermodynamic heating environment to mimic what the spacecraft endured. When the effect of thermal alteration on this alpha-beta phase alloy was investigated during previous studies, optical metallography and microhardness tests revealed inconsistencies between samples …

Nano-Engineered Soft Magnets: Potential Application In Water Treatment, Hyperthermia And Molecular (Organic) Magnets, Yohannes Weldemariam Getahun

Open Access Theses & Dissertations

Scrutinizing the remarkable and tunable properties of magnetic materials at a nanoscale size "There's Plenty of Room at the Bottom..." Richard Feynman, this study attempts to find sustainable solutions to some of the deteriorating environmental, health, and energy problems the world is encountering. Due to their simple preparation, surface adaptability, and tunable magnetic and optical properties, magnetic nanoparticles have been extensively investigated in water treatment, cancer therapy, data storage, and more. However, relying on non-reusable and chemical-based treatment agents in water, complex and costly cancer treatment procedures and molecular magnets that operate far below room temperature limited those attempts from …

The Qualification Of Sealability And Creep Relaxation Of Additively Manufactured Zytel Gaskets For Pem Fuel Cells, Robert Lazarin

Open Access Theses & Dissertations

The purpose of this thesis is to study the feasibility of low-cost additive manufacturing of gaskets for proton exchange membrane fuel cells exposed to extreme temperature conditions ranging from -55°C to 100°C. With the growing popularity and decreasing costs of additive manufacturing technologies, specifically Material Extrusion (ME), research is being conducted to determine the feasibility of ME components. Thermally cycled PEMFCs may exhibit accelerated gasket deterioration, therefore, the mechanical stability of material extruded gaskets following a harsh thermal cycle must be assessed. The feasibility of the material extruded gaskets will be proven by manufacturing optimization and mechanical testing. The target …

Novel Interlaminar Reinforcement To Enhance The Impact Damage Resistance Of Carbon Fiber-Reinforced Polymer Matrix Composites, Daisy Haidee Mariscal

Open Access Theses & Dissertations

Aerospace, aircraft, marine, and automobile applications are increasingly using composite materials for lighter, higher stiffness, and strength properties. Despite these advantages, composite materials have one major disadvantage. The through-thickness properties are extremely weak when subjected to impact damage. When a composite material is subjected to a low-velocity impact, there is hardly any visible damage on the surface compromising the composite material internally without any external notice. Internal damage may be delamination, which is the most common, matrix cracking, and fiber breakage. A composite material is made up of layers of fiber. The interlaminar region is located in between these layers. …

Fabrication, Microstructure And Mechanical Characterization Of Crvnbtaw High Entropy Alloy Coatings Using Magnetron Sputtering, Jorge Quezada

Open Access Theses & Dissertations

In this project a CrVNbTaW high entropy alloy was evaluated. The samples were made using radio frequency magnetron sputtering and were made under similar conditions. The deposition parameters were explored to find the ideal deposition process. The process included a pressure from 0.1-2mTorr, 600C, 1 hour duration, at 100W power to guns, and constant argon flow. The samples were fabricated under similar parameters using silicon steel and sapphire substrates. The samples were analyzed and characterized using X-ray diffraction, scanning electron microscopy, atomic force microscopy, nanoindentation and corrosion testing. Based on these results we were able to get a better understanding …

Magnetic Structures Of Sawtooth Olivines Mn2six 4 (X = S, Se) Determined Through Neutron Powder Diffraction, Melaku Sisay Tafere

Open Access Theses & Dissertations

In olivine chalcogenide Mn2SiX 4 (X = S, Se) compounds, the Mn lattice produces a sawtooth, which is of critical significance in magnetism due to the potential for manifesting at bands in the magnon spectrum, a crucial component in magnonics. The compounds Mn2SiS4 and Mn2SiSe4 in Mn2SiX 4 family undergo antiferromagnetic phase transitions at T â?? 85 K and â?? 66 K, respectively, as determined from the specific heat, Cp(T). The average and local crystal structuresare determined using synchrotron X-ray, neutron diffraction, and X-ray total scattering data followed by Rietveld and pair distribution function (PDF) analysis. It is found from …

Laser Powder Bed Fusion Process, Structure, And Properties: Holistic Approach To Establishing Metallurgical Quality, Hunter Taylor

Open Access Theses & Dissertations

The advent of metal additive manufacturing (AM) was posed as a disruption to casting, forging, machining, and forming with the notion "complexity is free". However, since invention in the late 1990's the marketed potential has not been realized. Metal based AM is best viewed from the process-structure-properties-performance (PSPP) paradigm taught in material science and engineering, which links the process history to the part performance. Understanding the complex and localized process control made available by AM creates a significant challenge in defining the materials structure, properties, and performance. The lack of holistic understating of inputs and corresponding results has been identified …

Using Ultrasonication For The Improvement Of Grade And Recovery In Molybdenum Sulfide Flotation, Wayne Alexander Campbell

Open Access Theses & Dissertations

Experimentation was performed on molybdenite slurry by using ultrasonication to elucidate the effects of ultrasonic-induced bubble cavitation on the grade, recovery, and gangue reduction during small-scale flotation tests and was followed by a topographical analysis of quartz particles using SEM. Ultrasonic waves at 20-80 kHz that propagate through a liquid medium cause microbubbles to form, grow, and implode. The cavitation bubble's implosion causes brief extreme local conditions where temperatures can reach 5,000 K and pressures of 1,000 bar. The resulting microjets create mechanical and chemical changes to the system and were directed at improving flotation dynamics in these experiments. Through …

High Throughput And Highly Controllable Methods For In Vitro Intracellular Delivery, Justin Brooks, Grayson Minnick, Prithvijit Mukherjee, Arian Jaberi, Lingqian Chang, Horacio D. Espinosa, Ruiguo Yang

Department of Mechanical and Materials Engineering: Faculty Publications

In vitro and ex vivo intracellular delivery methods hold the key for releasing the full potential of tissue engineering, drug development, and many other applications. In recent years, there has been significant progress in the design and implementation of intracellular delivery systems capable of delivery at the same scale as viral transfection and bulk electroporation but offering fewer adverse outcomes. This review strives to examine a variety of methods for in vitro and ex vivo intracellular delivery such as flow-through microfluidics, engineered substrates, and automated probe-based systems from the perspective of throughput and control. Special attention is paid to a …

Efects Of Non‑Newtonian Viscosity On Arterial And Venous Fow And Transport, Sabrina Lynch, Nitesh Nama, C Alberto Figueroa

Department of Mechanical and Materials Engineering: Faculty Publications

It is well known that blood exhibits non-Newtonian viscosity, but it is generally modeled as a Newtonian fluid. However, in situations of low shear rate, the validity of the Newtonian assumption is questionable. In this study, we investigated differences between Newtonian and non-Newtonian hemodynamic metrics such as velocity, vorticity, and wall shear stress. In addition, we investigated cardiovascular transport using two different approaches, Eulerian mass transport and Lagrangian particle tracking. Non-Newtonian solutions revealed important differences in both hemodynamic and transport metrics relative to the Newtonian model. Most notably for the hemodynamic metrics, in-plane velocity and vorticity were consistently larger in …