Catalysis and Reaction Engineering Commons^™

Gold-Semiconductor Photocatalysts For Water Treatment Under Visible And Ultraviolet Light, Daniel Willis

LSU Doctoral Dissertations

Water scarcity threatens the lives of millions of people worldwide. It is imperative to improve the energy efficiency and affordability of water treatment methods to avoid a looming water-energy crisis. To meet this challenge, I have pursued research on the use of sunlight—our most reliable and abundant source of energy—to drive water treatment through photocatalysis. I explored the literature and found gold-semiconductor materials to hold promise for harvesting sunlight and catalyzing the breakdown of waterborne contaminants. Initially, I designed a novel optical cavity with gold (Au) nanoparticles on a zinc oxide / titania (TiO₂) / aluminum film stack …

Abiotic Sensor For Electrochemical Determination Of Chlorpyrifos In Natural Water Based On The Inhibition Of Silver Nanoparticles Oxidation, Ziad Khalifa, Moustafa Zahran, Magdy Zahran, Magdi Abdelazzem

Chemical Engineering

Chlorpyrifos, organophosphorus pesticide, is a persistent organic pollutant that may cause serious health problems. Herein, a simple, green, and sensitive electrochemical inhibition sensor based on silver nanoparticles (AgNP)-modified glassy carbon (GC) electrode was developed for the determination of chlorpyrifos in natural water for the first time. The chemical reduction technique based on natural reducing and capping agents such as dissolved organic matter (DOM), natural latex (NL) and mucilage was employed for AgNP synthesis. DOM-AgNP, NL-AgNP, and Mucilage-AgNP were immobilized on GC by sticking technique under the same voltammetric and electrolytic conditions. The oxidation behavior of the three modified electrodes was …

Preparations And Electrocatalytic Ethanol Properties Of Palladium Intercalated Hydrotalcite, Shou-Xun Hu, Liang Li, Jun-Hao Yang, Liu-Qiang Li, Zhi-Hao Jin

Journal of Electrochemistry

High-performance electrocatalysts play a vital role in the commercial application of direct fuel cells. Current anode materials still have such problems as low activity, easy poisoning and high cost. In this study, a new type of nano- palladium (Pd) catalyst was prepared by dipping method using layered double hydroxides (LDHs) as the carrier. X-ray diffractometer, scanning electron microscope (SEM), inductively coupled plasma mass spectrometer (ICP-MS), energy spectrometer, transmission electron microscope (TEM), cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscope were used to analyze the structure and electrocatalytic performance of the catalyst. The results showed that the newly prepared Pd/Mg-Al-LDHs still maintained …

Preparation Of Pdcoir Tetrahedron Nanocatalysts And Its Performance Toward Ethanol Oxidation Reaction, Zhi-Yuan Yu, Rui Huang, Jie Liu, Guang Li, Qian-Tong Song, Shi-Gang Sun

Journal of Electrochemistry

As a new energy conversion device, direct ethanol fuel cells (DEFCs) are widely concerned because of their remarkable advantages such as high theoretical energy density and wide fuel sources. However, the rapid development of DEFCs has been severely impeded due to the sluggish kinetic process and toxic intermediates especially in their anodic reactions. Palladium (Pd)-based materials are considered to be excellent anode catalysts for DEFCs, especially under alkaline conditions. And further improving their performance is an important direction to promote the development of DEFCs. Surface structure and composition are the key factors affecting the performance of catalysts which can be …

Research Progress In Electrodeposition Technology Of Titanium-Based Iridium Oxide Electrode, Dan-Dan Wu, Xu Wu

Journal of Electrochemistry

Titanium-based iridium oxide electrode has been widely used in various fields, such as electrocatalytic oxidation, biomedical applications, hydrometallurgical metal recovery, electro-osmotic dewatering, etc. At present, it is mainly prepared by traditional thermal decomposition method, however, which has high cost, cumbersome process, mainly relying on manual labor and cannot be mass-produced yet. It is, therefore, urgently necessary to explore new preparation technologies by focusing on electrodeposition technology, with technological characteristics such as eco-friendly and sustainable development. This article systematically discusses the research progress in iridium oxide electrodeposition preparation technology from the aspects of deposition solution formulation, base material selection and treatment, …

Syntheses Of Na3V2(Po4)2O2F As A Cathode For Sodium Ion Battery Application, Kai Wu

Journal of Electrochemistry

High-temperature solid-state method, hydro-thermal method and solvo-thermal method have been mainly employed to synthesize Na₃V₂(PO₄)₂O₂F (NVPF) cathode materials. However, these methods are energy consuming and complicated, which is not applicable for a large scale industrial production. In this study, a rather low-temperature (70℃) co-precipitation strategy was proposed to synthesize NVPF cathode materials. The as-prepared NVPF cathode materials showed a spherical shape with a diameter of 400 ~ 500 nm, and exhibited a sodium storage of 105.6 mAh·g^-1 and an efficiency of 90.06%. After a simple thermal process, the specific …

Ethinylation Reactions Of Some Aldehydes In The Presence Of Phenylacetylene Using High-Base Catalytic Systems, Abdurakhmanova Saida, Ikramov Abduvaxab, Ziyadullayev Odiljon, Ablakulov Lochin

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of the research work is the development of synthesis methods of aromatic acetylene alcohols and their various derivatives using different catalytic systems and also, determining their structure, physico-chemical and biological properties. The most effective way of synthesizing AAA is determined using selected complex catalytic systems and also, the range of catalytic activity of used catalysts is created. Acetic aldehyde, benzaldehyde and cyclohexonal, high-base catalytic systems − MOH/ДМСО∙H2O and M2CO3/ДMСO∙H2O with phenylacetylene reaction of enantioselective etynilation were investiged. Efficiency and course of chemical reaction in the process of formation acetylene alcohol affection of temperature, reaction duration, solvents, catalysts and …

Synthesis Of Meta-Altered Arylmaleinamide And Preparation Of Esters In Their Presence, Turaeva Khurshida, Yuldasheva Mukhabbat, Khaydarova Sadokat

CHEMISTRY AND CHEMICAL ENGINEERING

The development of new methods of synthesis using cheaper reagents for the preparation of maleic acid derivatives, the study of chemical properties and the determination of new directions for the practical application of maleic acid derivatives are still relevant. Therefore, the development of this work is an urgent task. The aim of this study was to obtain the synthesis of monomaleinamide compounds under various conditions to obtain arylmaleimide derivatives of maleic acid and to transfer them in a pure state for further reactions. In this study, scientific studies were carried out to find convenient methods for the preparation of monoamide …

Assessment Of Heavy Metal Concentration In Soils Around Geita The Gold Mine, Tanzania, Mariam G. Mgendi, Mkabwa L. K Manoko, W.J.S. Mwegoha, C. Southway C. Southway

Journal of Humanities and Social Sciences

Health issues related to gold mining cannot be underestimated. Gold mining produce acid mine drainage (AMD), which in turn releases heavy metals into the nearby environment, hence causing environmental pollution. Heavy metals are naturally very toxic, thus pose a great health concern especially when their concentration exceeds the recommended permissible limits. In this study, concentrations of five heavy metals—including Pb, Ni, Cr, Cu and Zn—were assessed in the soil around Geita Gold Mine (GGM). A total of 17 sampling sites were established from which the soil samples were collected at 0-15cm and 15-30cm soil depth. The concentration of both total …

New Mechanism Insight For The Hydrogenation Of Co/Co2 Gas Mixtures To Hydrocarbons Over Iron-Based Catalyst, Sandeep Badoga, Michela Martinelli, Muthu Kumaran Gnanamani, Young Koh, Wilson D. Shafer

Center for Applied Energy Research Faculty and Staff Publications

Iron-based catalysts are the most suitable candidates for converting CO₂ or CO₂-rich syngas to hydrocarbons. However, several issues about the mechanism of CO₂ hydrogenation are still unclear. In this work, we investigated the performance of an iron-based catalyst with H₂/CO₂, H₂/CO/N₂ and H₂/CO/¹³CO₂/N₂ gas mixtures at the same process conditions (T = 270°C, P = 175 psi and SV = 3 NL/h/g_cat). The CO₂ hydrogenation rate was much lower than that observed for CO hydrogenation. ¹³CO_{2 …}

Preparation Of Co-Electrodeposited Pd-Au Nanocatalyst For Methanol Electro-Oxidation, Islam M. Al-Akraa, Ahmad M. Mohammad, Yaser M. Asal, Sayed S. Abd El Rehim

Chemical Engineering

No abstract provided.

New Horizons For Processing And Utilizing Red Mud, M. Archambo

Dissertations, Master's Theses and Master's Reports

Red mud is an industrial slurry waste that is produced as a byproduct of the Bayer process for alumina. The waste is generated in large quantities, up to a ratio of 2:1 against the valued product alumina. Red mud exhibits many chemical and physical properties that categorize it as a hazardous material. Due to the addition of sodium hydroxide in processing, the pH is typically at values close to 13. Small particle size discourages separation from water for disposal, so drying red mud happens over many years.

The pH of red mud can be reduced with inexpensive reagents. Carbon dioxide …

Carbon Capture And Utilization, Sriram Valluri

Dissertations, Master's Theses and Master's Reports

As the world moves towards clean energy initiative, carbon capture and utilization technologies are key to achieving net zero emissions. CO2 capture with amines has many disadvantages and cannot be applied to commercial power plants. The current manuscript will address this issue as well as a solution that involves the use of low-cost alkali absorbent CO₂ capture solutions, combined with an electrochemical regeneration method that uses the least amount of energy available for capture and regeneration. This research will also further address the issue of how to deal with the captured CO2. Several viable storage and utilization methods have …

Effects Of Microporous Structure On The Enzymatic Conversion Of Biomass Using A Multiscale Model, Saketh Merugu

Dissertations, Master's Theses and Master's Reports

The generation of biofuels from lignocellulosic biomass involves innovative process technology that is being investigated worldwide. Enzymatic hydrolysis is a major step in the contemporary process of the generation of biofuels. Guided by pore size distribution measured using NMR cryoporometry, we developed pore-enzyme diffusion and adsorption models at the particle level coupled with a kinetic model for cellulose, cellobiose, and glucose production at flask level. By simulating these models in MATLAB, COMSOL, and Polymath software packages, we investigate the effects of various biomass particle-related parameters (particle dimensions, porosity, enzyme accessibility) on the characteristic time of enzyme diffusion and adsorption and …

Dry Reforming Of Methane Using Microwave Irradiated Metal Oxide/Coal Char Catalysts, Anthony Carter

Graduate Theses, Dissertations, and Problem Reports (ETD)

This research focuses on the synthesis of both shaped and amorphous powder materials, the combination of these materials with dried Powder River Basin (PRB) coal char, and their reactionary properties with methane and carbon dioxide gasses with conventional and microwave (MW) heating. The first goal of this project was to synthesize shaped micro and nano sized particles with ideal dielectric properties for converting electromagnetic energy into heat and proven capabilities of activating methane. These particles were synthesized via solvothermal, hydrothermal, and co-preceptory treatments alone and onto the surface of dried PRB coal char. PRB is a sub-bituminous, low-ranking coal (LRC) …

Cold Plasma Enhanced Active Sites On Supported Nip Nanoparticles For The Oxygen Evolution Reaction, Michael Ricci

Williams Honors College, Honors Research Projects

Identifying materials to efficiently facilitate the oxygen evolution reaction (OER) is key to advancing water electrolysis, an essential technology in the pathway towards a sustainable energy future. Here, we explore cold-plasma treatment as a facile method to enhance the activity of NiP nanoparticles supported on activated carbon. NiP nanoparticles were synthesized on an activated carbon support using a solid-state method and were then treated with argon, oxygen, and hydrogen plasmas for extended times. In all cases, plasma treatment reduced the number of active sites on the support. OER activity was evaluated by testing the materials in alkaline conditions. The activities …

Continuous Preparation And Application Of Novel Heterogeneous Catalysis, Michael B. Burkholder

Theses and Dissertations

Transition metal heterogeneous catalysts are widely used across many chemical industries to reduce waste and emissions and reduce production time while increasing rate. The prevalence of these materials results from the complex relationship between metal nanoparticles and supports affecting final catalytic performance. Rational catalyst synthesis describes the ability to precisely engineer structures through controlled preparation. Novel materials and continuous processing represent a promising approach for rational catalyst synthesis.

The application of these catalysts in continuous, multiphase processes, such as cross-coupling reactions, oxidation chemistry, and nitroreduction processes, are paramount to developing new commercial routes for high-value products. Pd/G catalysts synthesized by …

Improving Performance And Durability Of Intermediate Temperature Proton‐Conducting Solid Oxide Electrolysis Cells Via Materials Design And Catalyst Surface Engineering, Hanchen Tian

Graduate Theses, Dissertations, and Problem Reports (ETD)

Solid oxide steam electrolysis cell, a promising electrical-chemical conversion device for the next generation efficient hydrogen production and energy storage, has been actively studied because of their high energy conversion efficiencies and prospective applications as electrochemical reactors. After decades of research on protonic ceramic materials, remarkable advances have been made in the protonic ceramic electrochemical cells (PCECs) air electrode and electrolyte. However, the existing air electrodes are far from satisfying the requirements of practical applications, a series of issues, including the lack of active and durable electrodes, greatly limit the commercialization. To date, the systematic development of triple conducting catalysts …

Simultaneous Activation Of Stable Molecules- Methane And Nitrogen- Using Microwave Reactor With And Without Plasma- To Produce Ethylene And Ammonia, Sarojini Tiwari

Graduate Theses, Dissertations, and Problem Reports (ETD)

The discovery of stranded natural gas around the world has made shale gas cheaper and widely accessible. This has driven the relevant research towards the direct utilization of Methane (CH4), a major component of natural gas. CH4 is a highly stable molecule, hence its activation and consequent formation of value-added chemicals in a direct and efficient manner is a relevant problem of the 21st century. All the commercial processes convert natural gas to chemicals indirectly, via the formation of syngas followed by several reactions. The conventional systems are energy intensive and one of the major contributors to green-house gas emissions. …

Microwave-Assisted Natural Gas Conversion To Value-Added Chemicals, Xinwei Bai

Graduate Theses, Dissertations, and Problem Reports (ETD)

Stranded gas is a raw gas mixture of volatile hydrocarbons where the main composition is methane. The producers flare the stranded gas at the site because the cost of collecting and transporting the gas is higher than the value of the gas itself. To reduce the waste of this natural resource, it is worthwhile to utilize the on-site stranded natural gas as feedstock to produce value-added chemicals without emitting greenhouse gas. Direct natural gas conversion process is more desirable because of lower capital investment. Methane and ethane, the two major components of natural gas, are very stable molecules that usually …

Valorization Of Xylan In Agroforestry Waste Streams, Harrison Appiah

Graduate Theses, Dissertations, and Problem Reports (ETD)

Valorization of Xylan in Agroforestry Waste Streams.

Harrison Appiah

Microwave-assisted deep eutectic solvent and gamma-valerolactone metallic chloride catalyzed conversion of xylan to furfural were investigated using a 2x3 factorial experimental design at two levels of percent microwave power, reaction time, and catalyst concentration. The levels of each factor studied were (20%, 60% microwave power, 2, 4 minutes, and 10, 20mg) respectively. The effect of three metallic chloride catalysts (LiCl, FeCl3.6H20, CuCl2) on the conversion of xylan to furfural was also investigated. The gamma-valerolactone-ferric chloride sent system exhibited the highest mean yield of furfural (56.50%). The next highest furfural yield of …

Natural Gas Conversion To Value-Added Chemicals By Microwave Catalytic Processes, Brandon Robinson

Graduate Theses, Dissertations, and Problem Reports (ETD)

Ethane is the second-largest component in natural gas and is typically separated out to minimize condensation in the pipelines. The technical difficulties and cost associated with the transportation and the storage of ethane have led companies to start burning natural gas to produce power or flaring which attributes to the global CO₂ emission problem. The conversion of ethane to higher-value liquid products is of increasing importance so that the natural gas can be safely utilized and cost-effectively transported. Existing commercial technologies used to convert ethane to liquid chemical products are typically based on the indirect syngas route, such as …

Biological Conversion Of Carbon Dioxide To Value-Added Chemicals, Owen James Mcgrath

Graduate Theses, Dissertations, and Problem Reports (ETD)

As Carbon Dioxide (CO₂) levels in the atmosphere continue to rise due to human intervention, there is increased urgency to take actions to mitigate the potential ramifications. Many countries have instituted a CO₂ tax and have provided funding to finding potential solutions to our growing CO₂ problem. Further investigating CO₂ capture, sequestration, and utilization is key to combating rising CO₂ levels and methods being investigated have increased substantially in recent years. Converting CO₂ into fuels and value-added chemicals provides a unique opportunity to create materials of value from a substance that is being …

Preparation And Characterization Of Reactive Composites Combining Boron With Mixed Oxides, Purvam Mehulkumar Gandhi

Theses

Thirteen liquids have been explored as Process Control Agents (PCAs) for high-energy mechanical milling of two metal oxide powders, CuO and Bi₂O₃, with the practical purpose to reduce the sizes of powder particles and refine their crystal structure. Multiple liquid properties have been considered to analyze their effect on evolution of both particle and crystallite sizes during milling for each oxide. Experimental data were analyzed using the δ-AICc (Akaike Information criterion) correlation function applied to linear relations between liquid properties and powder characteristics. Multiple linear correlation models were ranked based on the highest log-likelihood and the …

Mixed Complex Compounds Of Palmitate, Oleate Calcium With Acetamide, Nicotinamide And Thiocarbamide, Ibadullaeva Tursunoy, Azizov Tokhir, Ibragimova Мavluda

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of the study was the synthesis and study of the structure of mixed complexes of palmitate, calcium oleate with acetamide, nicotinamide and thiocarbamide. The mixed coordination compounds of palmitate and calcium oleate were synthesized. The composition, individuality, thermal behavior, methods of coordinating the palmitate and oleate fragments, acetamide, nicotinamide and thiocarbamide molecules have been established. Comparison of the diffraction patterns of calcium palmitate and oleate, free ligand molecules and synthesized compounds showed the mismatch of the diffractograms, conseqently that the synthesized complexes have an individual crystal lattice different from the starting materials. The method of coordination of amide …

Synthesis Of Esters Of Halogenoacetic Acids, Yuldasheva Muxabbat, Turaev Sherzod

CHEMISTRY AND CHEMICAL ENGINEERING

Amidoalkylating reagents containing a phthalimide group are used in the synthesis of hard-to-reach primary amines and complex heterocyclic compounds. These types of amidoalkylating compounds are suitable reagents for nucleophilic substituted reactions in acidic media due to their resistance to acids. Result of reactions of amidoalkylating reagents-N-hydroxyethylphthalimide and N-hydroxymethylphthalimide with aliphatic carbonic acids can also produce new bactericidal and fungicidal esters. In this study, halogen acids reacted with N-hydroxymethylphthalimide monochloric acetic acid, monobromic acetic acid, monoiodic acetic acid, trifluoric acetic acid and trichloroacetic acid, as well as, N-b-hydroxyethylphthaleidyl monohydric acid. As a result of the reactions, new phthalimidomethyl and phthalimidoethyl esters …

Numerical Simulations Of Current And Temperature Distribution Of Symmetrical Double-Cathode Solid Oxide Fuel Cell Stacks Based On The Theory Of Electric-Chemical-Thermal Coupling, Cheng-Rong Yu, Jian-Guo Zhu, Cong-Ying Jiang, Yu-Chen Gu, Ye-Xin Zhou, Zhuo-Bin Li, Rong-Min Wu, Zheng Zhong, Wan-Bing Guan

Journal of Electrochemistry

Solid oxide fuel cell (SOFC) is a high-efficient clean conversion device for future energy management. Because of the low antioxidant reduction ability and complex thermal stress, the structure of traditional asymmetrical thin anode-supported planar SOFC is easily to be broken under stack operating conditions. To overcome these defects, a new complete symmetrical SOFC based on double-sided cathodes was developed. To study the influences of gas flow direction and current collection mode on the cell performance inside stack, a numerical model was established by finite element method based on the theory of electro-thermo-chemo multiphysical coupling. By applying this model, the molar …

Effect Of Reaction Conditions On Cu⁃Catalyzed Co2 Electroreduction, Chang Zhu, Wei Chen, Yan-Fang Song, Xiao Dong, Gui-Hua Li, Wei Wei, Yu-Han Sun

Journal of Electrochemistry

Electrochemical conversion of carbon dioxide (CO₂) driven by renewable electricity that can meet both carbon emission reduction and renewable energy utilization has been rapidly developed in recent years. Copper (Cu) catalyst has long been a promising candidate for CO₂ electroreduction applications because of its natural abundance and specific capability of producing a substantial amount of C2 products. However, various metallic Cu electrodes reported have been significantly influenced by the adsorption of certain cation/anion ions, resulting in wide-span catalytic activities and selectivity for various products. In addition, a recent report demonstrated that by virtue of gas-diffusion flow cell …

Core-Shell Structured Ru@Ptru Nanoflower Electrocatalysts Toward Alkaline Hydrogen Evolution Reaction, Xue-Liang Wang, Yuan-Yuan Cong, Chen-Xi Qiu, Sheng-Jie Wang, Jia-Qi Qin, Yu-Jiang Song

Journal of Electrochemistry

Water electrolysis for hydrogen production is beneficial for solving the problem of energy crisis and environmental issues. It is necessary to study highly active and cost-effective catalysts toward hydrogen evolution reaction (HER) to reduce the consumption of noble metals. Herein, we report the synthesis of core-shell structured Ru@Pt_0.24Ru nanoflowers electrocatalyst by stepwise reduction of Ru and Pt precursors in the mixture of oleylamine and benzyl alcohol at 160 ^oC. The average diameter of the resultant Ru@Pt_0.24Ru was 16.5±4.0 nm with a bulk atomic ratio between Pt and Ru of 0.24:1 and a surface ratio of …

Reduction Of Copper And Iron Oxide Mixture With Local Reducing Gases, Shokhrukh Khojiev

Acta of Turin Polytechnic University in Tashkent

The article analyzes the scientific problems of the copper industry. In particular, the main problem with the classical production of copper is the causes of large amounts of slag and the negative impact of these wastes on the environment. Accordingly, the main component that forms the slag is iron, and the higher its content in the original copper concentrate, the more slag is formed, and at the same time a large amount of copper metal is released into the waste. The departure is indicated by evidence. To prevent this problem, a technology has been proposed to reduce copper sulfide concentrates …