Catalysis and Reaction Engineering Commons^™

Effect Of Glycol Based Coolant Pollution On Pem Fuel Cells Stack And Recovery Measures, Cong-Yi Zhu, Xiao-Hui Li, Quan-Quan Gan

Journal of Electrochemistry

As the heat conduction medium of fuel cell cooling system, coolant is very important for the thermal management of fuel cell stack. In practical application, coolant leakage into the stack often occurs. Due to the randomness of fault location of components, the location of coolant leakage is uncertain, which may occur on the cathode side or anode side of some or all single cells. The main effects of coolant pollution on fuel cell stack are as follows: the output of open circuit voltage decreases sharply, the consistency of single cells voltage decreases and so on, which seriously affects the normal …

Formation And Morphological Evolution Of Nanoporous Anodized Iron Oxide Films, Jin-Wei Cao, Nan Gao, Zhao-Qing Gao, Chen Wang, Sheng-Yan Shang, Yun-Peng Wang, Hai-Tao Ma

Journal of Electrochemistry

The preparation of iron oxide films with nanoporous structure by anodization has attracted much attention for its potential applications. However, the formation mechanism of porous structure during anodization is still unclear. In this paper, the composition of anodic current during the formation of nanoporous anodized iron oxide film was analyzed in combination with the current density-potential response (I-V curve) and the derivation of Faraday’s law. The results showed that the anodic current consisted of an ionic current (leading to the migration of ions to form oxide) and an electronic current (leading to the oxygen evolution), and the …

Copper Nanoparticles In-Situ Anchored On Nitrogen-Doped Carbon For High-Efficiency Oxygen Reduction Reaction Electrocatalyst, Hui-Fang Yuan, Yue Zhang, Xing-Wu Zhai, Li-Bing Hu, Gui-Xian Ge, Gang Wang, Feng Yu, Bin Dai

Journal of Electrochemistry

Compared with noble metal platinum (Pt)-based catalysts, inexpensive non-noble metal electrocatalysts have attracted extensive attention for oxygen reduction reaction (ORR). Herein, chitosan as a kind of biomass resource rich in nitrogen and carbon was used to prepare nitrogen-doped carbon (N-C) and N-C in-situ anchored by copper nanoparticles (Cu/N-C). The as-obtained N-C and Cu/N-C nanoparticles were successfully used as non-noble eletrocatalysts tested for ORR. Compared with the N-C, the Cu/N-C showed the high surface area of 607.3 m ²·g^-1 with the mean pore size of 2.5 nm and the pore volume of 0.40 cm³·g^{-1 …}

Structure Analysis Of Pemfc Cathode Catalyst Layer, Rui-Qing Wang, Sheng Sui

Journal of Electrochemistry

The sluggish oxygen reduction reaction (ORR) on the cathode of the proton exchange membrane fuel cell (PEMFC) has always been one of the key factors limiting its commercialization. The optimization of the cathode catalytic layer structure plays an important role in improving fuel cell performance and reducing production costs. In this paper, two different catalysts (platinum nanoparticles (Pt-NPs) and platinum nanowires (Pt-NWs)) were prepared by using catalyst coated substrate (CCS) method. By constructing a double-layer catalytic layer structure, we analyzed the effect of different catalytic layer structures by performing a single cell test. The results showed that the dense platinum …

Catalytic Light Alkanes Selective Conversion Through Ammonia-Assisted Reforming, Siavash Fadaeerayeni

Theses and Dissertations

The fact that hydrogen is a clean and versatile fuel offers an attractive carbon-free source of energy and leverages the U.S. economy toward long-term sustainable economic growth. At an industrial scale, hydrogen production is mostly relying on methane steam reforming producing stoichiometric amounts of carbon oxides (CO and CO2), which imposes economic and environmental concerns. To mitigate the issue, we propose NH3 assisted anaerobic reforming of natural gas liquids (ethane and propane) as an alternative approach to produce COx free hydrogen. Here, in the first chapter, through comprehensive performance evaluation, characterization, and transient kinetic studies, it is shown that the …

Solvent Engineering Of Molybdenum Disulfide Electrocatalyst For Hydrogen Evolution., Robert Carl Spalding

Electronic Theses and Dissertations

Energy is at an exponentially growing demand, and to keep up with these demands new technologies for renewable energy have received increased attention. Hydrogen plays a vital role in water electrolysis and fuel cells, as the hydrogen evolution reaction (HER) is the main step water splitting process. Most of the current electrocatalysts for HER are dominated by platinum and other precious metals due to their low over-potential and small Tafel slope, however, they are extremely costly. For this reason, cost-effective non-precious metal catalysts must be developed. Transition metal dichalcogenides, such as molybdenum disulfide (MoS2), are abundant and have recently shown …

Investigation Of Iron-Nickel Films Based Catalysts: Controlling Hydrogen Evolution Reaction (Her) Through An Electrode-Electrolyte Engineering Approach, Sergio Ivan Perez Bakovic

Graduate Theses and Dissertations

Electrochemical energy conversion technologies need to be economically viable in order to be adopted. Earth-abundant transition metals (i.e., Fe, Co, and Ni) have attracted attention due to their high availability, low cost, and catalytic characteristics that are in many cases found in and exploited by nature. Herein, we synthesize FexNi100-xOy electrocatalyst films and study how the electrocatalyst-electrolyte interactions alter the hydrogen evolution reaction (HER).In this work, FexNi100-xOy films were synthesized to study the composition, chemical state, and morphology. Characterization results provided a well-established electrocatalyst film platform to then proceed with electrochemical evaluations. The effects of the electrode composition and electrochemically …

Electrochemical Synthesis Of P-(Β-Hydroxyethyl Sulfone) Aniline, Hao Guo, Dong-Fang Niu, Shuo-Zhen Hu, Xin-Sheng Zhang

Journal of Electrochemistry

Para-ester is the most important intermediate for the preparation of ethylene sulfone type reactive dyes, which is usually used in the dyeing of cellulose fibers and synthetic fibers. P-(β-hydroxyethyl sulfone) aniline is an important intermediate for the synthesis of para-ester. In this paper, p-(β-hydroxyethyl sulfone) aniline was prepared by electrochemical method, having the advantages of simple process, mild reaction condition, less environmental pollution, easy reaction control and so on. It has strong development potential and industrial application prospect. The electrochemical reduction of p-nitrophenyl-β-hydroxyethyl sulfone on a lead plate electrode to prepare p-(β-hydroxyethyl …

Synthesis Of Nickel Phosphide/Nitrogen Phosphorus Co-Doped Carbon And Its Application In Lithium Ion Batteries, Jian Hu, Yan-Shuang Meng, Qian-Ru Hu

Journal of Electrochemistry

In recent years, the nickel-based phosphide has drawn great attention because of its low intercalation/deintercalation platform and lower polarization compared to sulfides and oxides as anodes for next-generation high-energy lithium-ion batteries. The Ni₂P anode can deliver high theoretical specific capacity of 542 mAh·g^-1, but it subject to a conversion reaction mechanism, which make them unsuitable for commercial applications. The agglomeration of Ni₂P nanoparticles during material fabrication and the structural deterioration of electrode associated with large volume change during charge-discharge process lead to poor cycle stability and low utilization of active materials. Meanwhile, the low …

Performance And Mechanism Of PtXCuY/C Electrocatalyst For Methanol Oxidation, Jia Tang, Xiao-Ming Zhang, Shan-Sheng Yu, Su-Li Wang, Gong-Quan Sun

Journal of Electrochemistry

Direct methanol fuel cell (DMFC), which directly converts the chemical energy of methanol fuel into electrical energy, has the advantages of high energy conversion efficiency, environmental friendliness, and abundance of fuel sources. DMFC is considered as the promising substitutes in the field of portable devices, military applications, and stationary power stations, while the broad application is severely hindered by the sluggish kinetic of methanol oxidation reaction (MOR) in the anode and the high cost of platinum (Pt)-based anodic electrocatalysts. Herein, a series of carbon supported Pt_xCu_y (Pt_xCu_y/C) binary metal electrocatalysts, featured with high …

Effect Of Alkyl Chain Length Of Symmetrical Quaternary Ammonium Hydroxide On Oxalic Acid Electroreduction Reaction, Bo Huang, Xin-Sheng Zhang, Dong-Fang Niu, Shuo-Zhen Hu

Journal of Electrochemistry

Glyoxylic acid with the dual characteristics of acid and aldehyde is an important chemical raw material and organic synthesis intermediate, which is extensively used in the perfumery, pharmaceutical and fine chemical industries. A family of symmetric quaternary ammonium hydroxides (QAHs) with different alkyl chain lengths was used as the additives in generating glyoxylic acid from oxalic acid electroreduction reaction (OAER). The effects of alkyl chain length on OAER and the corresponding side reaction, i.e., hydrogen evolution reaction (HER), were investigated. Linear sweep voltammetric (LSV) results showed that the adsorption of the additives suppressed more on the HER than that on …

Recent Advances In Silver Nanoparticle-Based Electrochemical Sensors For Determining Organic Pollutants In Water, Ziad Khalifa, Moustafa Zahran, Magdy Zahran, Magdi Abdelazzem

Chemical Engineering

Water pollutants have attracted great attention because of their negative effect on human health. Accordingly, various analytical techniques have been investigated to detect water pollutants as a preliminary step for their control. This review highlights silver nanoparticles (AgNPs) as promising electrochemical probes studied for detecting organic pollutants. Electrochemical sensors can be fabricated by modifying electrode surfaces using AgNPs via different techniques, such as electrochemical deposition, drop casting, spin coating, sticking, and transfer sticking, as well as carbon paste-based modification. AgNPs at electrode surfaces can be identified by their stripping to form Ag+ with a particular oxidation peak. Additionally, they can …

Synthesis And Research Of Silicon-Containing Phthalocyanine, Dilmurod Shukurov, Hayit Turayev, Abdulakhat Djalilov, Masud Karimov

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of this study is to synthesize, and study a new form of dye based on phthalocyanine, a silicon-containing phthalocyanine pigment used as a dye for dye-sensitive solar cells, which are currently third generation solar cells as one of the energy source alternatives. To achieve this goal, a silicon-containing phthalocyanine pigment containing urea, phthalic anhydride and sodium fluorosilicate was synthesized and studied. Based on the results of IR spectroscopy, the reaction of pigment formation is proposed and the data of scanning electron microscopy is presented. Its differential thermal analysis, photodynamic analysis and its relationship with inorganic and organic solvents …

Dft Study Of NiM@Pt1AuN-M-1 (N=19, 38, 55, 79; M = 1, 6, 13, 19) Core-Shell Orr Catalyst, Wen-Jie Li, Dong-Xu Tian, Hong Du, Xi-Qiang Yan

Journal of Electrochemistry

The slow kinetics of oxygen reduction reaction (ORR) limits the performance of low temperature fuel cells. Thus, it needs to design effective catalysts with low cost. Core-shell clusters (CSNCs) show promising activity because of their size-dependent geometric and electronic effects. The ORR activity trend of Ni_m@Pt₁Au_n-m-1(n = 19, 38, 55, 79; m = 1, 6, 13, 19) was studied using the GGA-PBE-PAW methods. The adsorption configurations of *O, *OH and *OOH were optimized and the reaction free energies of four proton electron (H⁺ + e^-) transfer steps …

One-Pot Synthesis Of Fe2O3@Fe-N-C Oxygen Reduction Electrocatalyst And Its Performance For Zinc-Air Battery, Hua Lin, Yi-Jin Wu, Jun-Tao Li, Yao Zhou

Journal of Electrochemistry

Oxygen reduction reaction (ORR) plays a profound role in determining cathode performance in metal-air batteries and fuel cells. Owing to its inherently sluggish kinetics, high-performance ORR catalysts which favors the scissoring of O-O bond and formation of O-H bond are a requisite. In this regard, Pt has been explored as the most efficient ORR electrocatalysts. Nevertheless, due to its expensiveness, the usage of Pt catalysts represents one of the major sources of cost in those energy conversion devices. Thus, the development of alternative ORR electrocatalysts with minimized Pt utilization has been widely pursued over the past few decades. Metal-nitrogen-carbon catalysts …

Preparation And Electrochemical Evaluation Of Mos2/Graphene Quantum Dots As A Catalyst For Hydrogen Evolution In Microbial Electrolysis Cell, Hong-Yan Dai, Hui-Min Yang, Xian Liu, Xiu-Li Song, Zhen-Hai Liang

Journal of Electrochemistry

Microbial electrolysis cell (MEC) is a relatively new bioelectrochemical technology that produces H₂ and meanwhile treats organic wastewater. Cathode hydrogen evolution catalyst plays a key role in MEC. The doping of Graphene Quantum Dots (GQDs) into MoS₂ nanosheets can improve the catalytic activity of MoS₂ by creating abundant defect sites both in the edge plane and the basal plane, as well as enhancing the electrical conductivity. In this paper, using Na₂MoO₄ , cysteine and GQDs as raw materials, a series of MoS₂/GQDs composites were firstly synthesized via hydrothermal method, and then loaded …

Preparation Of Coo/Rgo@Ni Foam Electrode And Its Electrocatalytic Reduction Of Co2, Qian Guo, Jia-Long Fu, Cheng-Yan Zhang, Chao-Yue Cai, Cheng Wang, Li-Hua Zhou, Rui-Bo Xu, Ming-Yan Wang

Journal of Electrochemistry

The worldwide extensive release of carbon dioxide (CO₂) has caused serious environmental pollution and unprecedented climate change problems. Thus, for the sustainable development of human society, it is very necessary to convert CO₂ to renewable fuels through clean and economical processes. The electrochemical CO₂ reduction reaction (CO₂RR) is regarded as a promising approach for the recycling of carbon resource and the generation of sustainable fuels. However, the slow kinetics and formation of multiple products in CO₂RR hinder its large-scale application. Hence, great research efforts are made to develop electrocatalysts with high product …

Engineering The Surface Of Fe3o4 Nanoparticles For Catalytic And Magnetic Applications, Natalia Da Silva Moura

LSU Doctoral Dissertations

With the rapid depletion of the U.S. energy resources coupled with population growth, heat management technologies must be improved to sustain our quality of life. Precisely, in catalysis, it is estimated that only ~50% of the energy supplied to the reactor is used for product conversion due to dissipation losses. Among the emerging technologies with a promising reduction in heat losses is induction heating, offering targeted heat delivery with magnetic nanoparticles. Under alternating magnetic fields (AMF), these nanoparticles can absorb the energy from Radio-Frequency (RF) fields and dissipate it as heat on the nanoparticle surface. This in situ heat generation …

Gum Arabic-Capped Silver Nanoparticles For Electrochemical Amplification Sensing Of Methylene Blue In River Water, Ziad Khalifa, Moustafa Zahran, Magdy Zahran, Magdi Abdelazzem

Chemical Engineering

Herein, a novel electrochemical amplification sensor is developed for detecting methylene blue (MB) us- ing gum Arabic-capped silver nanoparticles (AgNPs) for the first time. Gum Arabic-AgNPs were fabricated via a direct chemical reduction technique using silver nitrate as an AgNPs precursor and gum Arabic as a reducing and capping agent. They were characterized using ultraviolet-visible (UV–Vis) spectrophotom- etry, square wave voltammetry (SWV), and transmission electron microscopy (TEM). UV–Vis and SWV results show the characteristic absorption and electrochemical oxidation peaks of the AgNPs at 431 nm and 0.18 V, respectively. Additionally, TEM images of the AgNPs show that they are spherical …

Direct Activation Of Light Alkanes To Value-Added Chemicals Using Supported Metal Oxide Catalysts, Md Ashraful Abedin

LSU Doctoral Dissertations

One of the most challenging aspects of modern-day catalysis is the conversion of methane. Direct conversion of methane via dehydroaromatization (MDHA) is a well-known process which can produce valuable hydrocarbons. Mo oxide supported on ZSM-5/MCM-22 has been studied extensively in recent years for MDHA. Mo carbides are responsible for activating methane by forming CHx species. These are dimerized into C2Hy and oligomerized on ZSM-5/MCM-22 Brønsted acid sites to form aromatics. Sulfated zirconia (SZ) supported Mo catalyst contains the acid sites necessary to produce benzene in MDHA. Here, sulfated hafnia (SH), a homologous oxide like SZ, has been proposed to provide …

Modified Electrode Surfaces With Hydrogen Evolution Reaction Catalysts Derived From Electropolymerized Complexes With Redox Active Ligands., Amanda Mae Arts

Electronic Theses and Dissertations

The demand for energy is growing exponentially, and to keep up with these demands new technologies for renewable energy have received increased attention. Hydrogen is one of the most promising energy sources for the future and plays a vital role in water electrolysis and fuel cells, as the hydrogen evolution reaction (HER) is the main step in the water splitting process. To increase the reaction rate and improve efficiency for the water electrolysis, catalysts are used to minimize the overpotential.

Most of the current electrocatalysts for HER are heterogeneous in nature and are dominated by platinum and other precious metals …

Rheological Properties Of Aged Crude Hard Wood Pyrolysis Oil, Divina D. Kaombe

Tanzania Journal of Engineering and Technology (TJET)

Upon storage of the pyrolysis oil, aging reactions may initiate phase separation and change of the rheological properties. These changes lead to unfavourable fuel characteristics in handling, transportation and applications. Efforts have been made for alleviation including methods on how to avoid these aging effects and development of equipment capable of handling aged pyrolysis liquids with unfavourable fuel characteristics. Therefore, the aim of this study was to explore the rheological properties of phase separated pyrolysis liquid fuel. Two batches of a well – stored poplar wood pyrolysis oils were used for the investigation; one batch was diluted with water to …

Investigation Of Iron-Nickel Based Nanoparticles As Catalysts For Oxygen Evolution Reaction (Oer), Prashant Acharya

Graduate Theses and Dissertations

Hydrogen fuel is increasingly seen as an appealing alternative by both the scientific and the industrial communities in the drive towards a clean energy future. Hydrogen, unlike fossil-based fuels, does not release carbon dioxide, a chief component of greenhouse gases, upon combustion. However, more than 95% of the hydrogen in the world is still produced by burning fossil fuels as this method is currently the only economically feasible option at a large industrial scale.

Water electrolysis shows a lot of potential in both hydrogen generation and in the storage of energy from renewable sources such as wind and sunlight. Likewise, …

A Portable Point-Of-Care Device Using Joule Heating And Latent Energy Storage For The Temperature Regulation Of Isothermal Nucleic Acid Amplification Tests, Aubrey Lynn Schultz

Graduate Theses and Dissertations

Accurate and early diagnosis of infectious diseases extremely important. Rapid diagnosis allows for effective treatment and increases the chance for recovery without complications. Additionally, the ability to test the populace frequently, swiftly, and affordably significantly aids in containing wide-scale outbreaks. In terms of specificity and sensitivity, nucleic acid amplification tests (NAAT) are one of the best options for diagnosing infectious diseases. Isothermal NAATS present a unique opportunity to create diagnostic tests deployed at a Point-of-Care (POC) level. Specifically, loop-mediated isothermal amplification (LAMP) and recombinase polymerase amplification (RPA) have the potential to deliver reliable POC diagnostics in low-resource settings. When designing …

Electrochemical Deposition In Energy Storage Devices, Witness Atutala Martin

Graduate Theses and Dissertations

Metals, whether in a solid or soluble ion form, are a vital part of any electrochemical storage system. More so, Li metal is widely considered as the ideal anode because of its low density and low electrochemical potential (-3.04 V vs. the standard hydrogen electrode – SHE). However, just like most metals, it does not plate or strip evenly during cycling which can lead to cycling performance issues, short cycling lifespans, and even safety concerns brought about by dendrites that can cause internal short-circuiting within cells. This research focused on investigating the electroplating of metals in both aqueous and non-aqueous …

Preparation Of Co1-XS-Mns@Cnts/Cnfs For Electrocatalytic Oxygen Reduction Reaction, Fang-Yan Liu, Qian Zhang, Yue-Kun Li, Feng Huang, Meng-Ye Wang

Journal of Electrochemistry

As an important cathode reaction in fuel cells and metal-air batteries, oxygen reduction reaction (ORR) is a complex reaction of slow kinetics, which severely limits performances of fuel cells and metal-air batteries. Therefore, it is of key importance to find an efficient and stable electrocatalyst to promote ORR. Carbon-based materials, which possess high conductivity, good stability and large specific surface area, are usually used in electrocatalytic ORR. However, pure carbon-based materials exhibit low efficiency. Coupling carbon-based materials with manganese (Mn) and cobalt (Co) transition metals containing 3d orbitals is an effective way to improve electrocatalytic performance. Herein, carbon nanofibers containing …

Synthesis And Electrochemical Study Of Cuau Nanodendrites For Co2 Reduction, Dylan Siltamaki, Shuai Chen, Farnood Rahmati, Jacek Lipkowski, Ai-Cheng Chen

Journal of Electrochemistry

The conversion of carbon dioxide (CO₂) to carbon monoxide (CO) and other value-added products is an interesting approach for carbon-containing fuel synthesis using renewable and clean energy. The electrochemical reduction of CO₂ is one of the promising strategies for the storage of intermittent renewable energy resources. The development of electrocatalysts with high activity and stability is vital in the electrochemical CO₂ reduction process. In this study, copper and gold alloyed (CuAu) electrodes with nanodendritic structures were synthesized using a facile electrodeposition method. The CuAu nanodendrites with the atomic ratio of Cu to Au being approximately 1:1 …

Recent Advances In Glycerol Electrooxidation On Pt And Pd: From Reaction Mechanisms To Catalytic Materials, Wei-Yi Zhang, Xian-Yin Ma, Shou-Zhong Zou, Wen-Bin Cai

Journal of Electrochemistry

The conversion of glycerol to value-added products has received considerable attention recently because the booming biodiesel industry produces a large amount of glycerol as a byproduct. Among various means, electrocatalytic oxidation of glycerol is appealing owing to its environmental friendliness and high efficiency. However, electrooxidation of glycerol is very complex, involving multiple electron and proton transfer processes with many reaction pathways. How to rationally design catalysts with high selectivity toward targeted products is an overarching challenge, and of both fundamental and practical significance. In this minireview we aim to provide an overview of recent advancements in electrooxidation of glycerol focusing …

Synthesis Of Aromatic Acetylene Alcohols Using Complex Catalytic Systems, Odiljon Ziyadullaev, Guzal Otamukhamedova, Abduvakhab Ikramov, Saida Abdurakhmanova, Otabek Boytemirov

CHEMISTRY AND CHEMICAL ENGINEERING

Some cyclic ketones (cyclopentanone, cyclohexanone, 2-methylcyclohexanone, menthol, camphor and adamantanone) enantioselective alkynylation reactions with phenylacetylene have been studied in the presence of complex catalytic systems - Zn(OTf)₂/NЕt₃/MeCN, 3,3′-Ph₂BINOL-2Li/TGF and BuLi/KO^tBu/TGF. Synthesis were performed new aromatic acetylene alcohols – 1-(2-phenylathinyl) cyclopentanol (1), 1-(2-phenylethinyl)cyclohexanol (2), 2-methyl-1-(2-phenylethinyl)cyclohexanol (3), 2-isopropyl-5-methyl-1-(2-phenylethinyl)cyclohexanol (4), 1,7,7,-trimethyl-2-(2-phenylethinyl)bicyclo [2.2.1] heptanol-2 (5) and 2-phenylethinyltricyclo [3,3,1.0^3,7]nonanol-2 (6). Synthesis reactions of aromatic acetylene alcohols, activation energies were determined, kinetic of chemical changes and reaction mechanisms were proposed. The course of the reactions and the effect of the selected ketone molecule size, structure and …

Heterogeneous Catalytic Conversions Of Acetylene, Abduvakhab Ikramov, Sevara Kholikova, Noryigit Musulmanov

CHEMISTRY AND CHEMICAL ENGINEERING

The reactions of interaction of acetylene with water vapor, acetic acid and ammonia in the presence of heterogeneous catalysts have investigated. Depending on the nature of the starting components used, acetaldehyde and acetone, vinyl acetate, pyridine bases and pyrrole synthesized. Heterogeneous catalysts selected for each studied reaction based on some scientific prerequisites for the selection of catalysts. Active catalysts for the investigated reactions were determined, which contain compounds of cadmium, zinc, bismuth, chromium, iron and copper, in general, d-group metals. γ-Al₂O₃, bentonite and kaolin used as a catalyst carrier. Hydrofluoric acid, acetic acid, ammonium fluoride and …