Catalysis and Reaction Engineering Commons^™

Thermogravimetric Analysis And Chemical Kinetics Of Waste Tires, Mahir Mohammed Said

Tanzania Journal of Engineering and Technology (TJET)

The focus of this paper is to analyse the pyrolysis reaction of waste tires. The pyrolysis was studied experimentally using thermal and chemical kinetics. The tires were pyrolyzed using thermogravimetry at a temperature range of 200 to 600°C, with heating rates of 10, 20, and 50°C/min. The activating energy was observed to increase with increased temperature. The highest activating energy was 101.02 kJ/mol at a heating rate of 50°C/min.

Enhanced Post Deposition Annealing Conditions On The Fabrication Of High Quality Thermochromic Vanadium Dioxide Films, Nuru R. Mlyuka

Tanzania Journal of Engineering and Technology (TJET)

Sputter deposition of thermochromic VO2 thin films for smart window applications has been faced with several challenges including the need for high deposition temperature, extremely precise and narrow range of oxygen/argon flow ratio and target poisoning during sputtering. Deposition of VO2 at room temperature without oxygen followed by post-deposition annealing has been cited as one of the potential mitigations to the challenge. In this study, the effects of post-deposition annealing conditions on the structural, electrical and optical properties of VO2 thin films are reported. The films were prepared on soda lime glass substrates using DC magnetron sputtering of metallic vanadium …

Design And Optimization Of An Azeotropic Distillation Pilot Plant For The Production Of Pure Ethanol, Samwel V. Manyele

Tanzania Journal of Engineering and Technology (TJET)

This study aimed to design an azeotropic distillation plant using Aspen Plus® V10 software and determine optimal process conditions for producing pure ethanol greater than 95% from pre-concentrated near-azeotropic ethanol-water solution. The non-random two-liquid Redlich-Kwong thermodynamic model was the base method for property analysis and performance prediction. Modelling and simulation of the converged process were conducted for fixed column variables (R = 5, N = 12 and p = 1 atm). Plant operating parameters were varied in the range of 0 to 1 for the pre-heater vapour fraction, 2 to 10 for the column feed plates (NFP), 2 to 6 …

Effect Of Zr And W Doping On Microstructures, Transition Temperature And Solar Transmittance Modulation Of Thermochromic W/Zr Co-Doped Vo2 Thin Films, Haji F. Haji

Tanzania Journal of Engineering and Technology (TJET)

Thermochromic W/Zr co-doped VO2-based thin films with different concentrations of Zr were successfully deposited on soda lime glass substrates by direct current (DC) magnetron sputtering of V(99)W(01) alloy and Zr targets at a substrate temperature of 425 °C. The films were characterized by x–ray diffraction (XRD), atomic force microscopy (AFM), Rutherford backscattering spectroscopy (RBS), two-point probe and UV/VIS/NIR spectroscopy. The film’s structural properties evolution was significantly influenced by Zr concentration in the films. The transition temperature and hysteresis loop widths of the films were found to decrease with increasing Zr concentration. For the Zr concentrations of 0.21 at.%, 0.23 at.% …

Sol-Gel Synthesis And Microstructure Characterization Of Nio-Tio2 Semiconductor, Godlisten N. Shao

Tanzania Journal of Engineering and Technology (TJET)

NiO-TiO2 is a fascinating p-n semiconducting binary metal oxide with unique electronic and optical properties. The NiO-TiO2 has been synthesized using complicated preparation methods and expensive precursors that hamper their large-scale production. The present study reports the preparation of NiO-TiO2 semiconductor with improved physicochemical properties. NiO-TiO2 samples were prepared through one-pot sol-gel synthesis process followed by sintering of the as-synthesized materials at temperatures ranging from 600 to 1000 °C. The role of thermal treatment and NiO content on the microstructures was exquisitely studied. The microstructure of the NiO-TiO2 samples was examined by Raman spectroscopy, XRD, XRF, SEM-EDAX, high resolution TEM, …

Sediment Characteristics And Hydrocarbon Composition Of Makukwa Seep In Southern Tanzania: Potential Implications For Subterranean Hydrocarbon Accumulation, Makungu M. Madirisha

Tanzania Journal of Engineering and Technology (TJET)

Exploring the interplay between natural seeps and nearby sediment and hydrocarbon properties is key to unlocking subsurface hydrocarbon potential. This study presents findings on the hydrocarbon composition and sediment characteristics of the Makukwa seep in southern Tanzania, providing insight into subterranean hydrocarbon accumulation. Sediment analysis across areas A and B, located approximately 20 m apart, showed a decrease in porosity with depth, indicative of typical sandstone formations. Area A, near the seeps, exhibited porosity ranging from 23% to 36%, whereas Area B, further away, showed porosity ranging from 22% to 38%. This suggests that a lower cretaceous sandstone layer may …

Production Of Biofertilizer From Fruit And Garden Waste, Neema Msuya

Tanzania Journal of Engineering and Technology (TJET)

The project focused on the production of bio-fertilizer from fruit and garden waste, with a specific emphasis on utilizing pineapple tops in the composting process. The objective was to produce and assess the properties of the bio fertilizer obtained from this process and evaluate its potential application in agriculture. In this study, the composting process was done in a 0.7 m long, 0.85 wide and 1.1 m high vessel, and 0.238 m3 pineapple top wastes, resulting in 0.35 m3 of biofertilizer. The bio fertilizer produced exhibited favorable characteristics, including a moisture content of 36%, pH of 7.1, and a total …

Study Of The Effects Of Thermal Aging Coupled With Shot-Peening Treatment Of Carbonitrided Din 1.6587 Low Alloy Steel On Retained Austenite And Residual Stresses, Richard J. Katemi

Tanzania Journal of Engineering and Technology (TJET)

This work investigated the effects of thermal aging and shot-peening of carbonitrided 1.6587 steel grade on retained austenite and residual stresses. After carbonitriding samples contained maximum of 0.87% carbon, 0.34% nitrogen and 50 mass. -% retained austenite. Thermal aging conditions investigated were -30°C, 90°C and 150°C while the aging period were 14, 96 and 720 hours. After thermal aging, some of the samples were subjected to shot-peening treatment using standard cut wire shots StD – G3 - 0.6 mm VDFI 8001 with intensity in the range of 0.25 to 0.30 mmA and coverage of 1.00 to 1.24 x 98%. It …

Study Of Reactive Distillation Equipment For Eterification Process, Abbos Elmanov, Abdulaziz Bakhtiyorov, Adham Norkobilov, Olimjon Maksudov, Zarif Oripov

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of this work is to study the chemical technological processes for eterification processes, and the reactive distillation unit, which carries out the reaction and separation process in one device, was chosen as the object of research. А reаctive distillаtion system is exаmined to produce for the production of Ethyl Acetate (EtAc) viа eterificаtion of acetic acid (HAc) with ethаnol. Optimizаtion methods using sensitivity analysis аre аlso conducted. Cаlculаtion of vаpor liquid equilibrium of the mixture system is done using UNIFАC model. Heat integration from the distillate stream of the column to the acid feed stream and from bottom …

Alkynylation Of Benzaldehyde And Its R-Substituted Derivatives Based On Lithium Phenylacetylenide, Sanat B. Samatov, Odiljon E. Ziyadullayev, Abduvakhab Ikramov

CHEMISTRY AND CHEMICAL ENGINEERING

The purpose of this research work is for the first time the synthesis of the corresponding acetylene alcohols based on the alkynylation reaction of isolated benzaldehyde and its R-substituted derivatives in the BuLi/TGF system. The study proposed the reaction stages for the synthesis of acetylene alcohols in the selected BuLi/TGF system, the influence of factors influencing the process, including temperature, reaction duration and nature selected solvents. The structure of the synthesized acetylene alcohols was confirmed by modern methods of physicochemical analysis (¹H NMR, ¹³C NMR). In addition, the effect of substituents in benzaldehyde and its R-substituted derivatives …

Electrocatalytic Cyclopropanation Of Active Methylene Compounds, Liang-Hua Jie, Hai-Chao Xu

Journal of Electrochemistry

The development of novel strategies to access cyclopropanes has become increasingly important due to the vital role of these three-membered ring structures in synthetic intermediates, natural products, and pharmaceuticals. Herein, we present an electrocatalytic method for the synthesis of cyclopropanes through intermolecular dehydrogenative annulation of active methylene compounds and arylalkenes. This electrochemical process requires no chemical oxidants, allowing for a speedy access to various functionalized cyclopropanes from inexpensive and readily available materials.

Electrochemical Syntheses Of Aryl-Substituted Benzothiophenes And Phenanthrenes Using Benzenediazonium Salts As The Aryl Radical Precursors, Li-Yuan Lan, Yang-Ye Jiang, Raymond Daniel Little, Cheng-Chu Zeng

Journal of Electrochemistry

Aryl-substituted benzothiophene and phenanthrene are important structural units in medicinal chemistry and materials science. Although extensive effort has been devoted to prepare these compounds and a variety of approaches have been developed to construct the 2-substituted benzothiophene core structure, environmental-friendly and efficient synthetic means are still desired. Based on our previous electrochemical Minisci-type arylation reaction with aryl diazonium salt as the aryl precursor, as well as the work from König’s group, herein, we described the use of paired electrolysis to achieve 2-aryl benzothiophenes and 9-aryl phenanthrenes employing benzenediazonium salts as the aryl radical precursors. Initially, 2-methylthiobenzendiazonium salt 1a and 4-methylbenzene …

Electrochemical Advanced Treatment Of Desulfurization Wastewater From Coal-Fired Power Plants, Ju-Cai Wei, Juan Yi, Xu Wu

Journal of Electrochemistry

Zero-emission of desulfurization wastewater is one of the main demands for coal-fired power plants. As typical high salinity wastewater, it is hard to purify the desulfurization wastewater from coal-fired power plants through traditional physicochemical treatment or biochemical treatment, e.g., COD and Cl^–. A high concentration of Cl^– ion in desulfurization wastewater restricts wastewater reuse and zero-emission. Electrochemical technology is an attractive method for high salinity wastewater zero-emission, which provides a versatile, efficient, cost-effective, easily automatable, and clean industrial process. For advanced treatment of effluent after triple box process treatment in power plants, this paper reports an electrochemical …

Cfd Study On Two-Phase Flow Patterns In A Pipe With 90º Elbow In Different Operating Conditions, Hagar Alm-Eldin Bastawissi, Mohammed Ahmed Khafagy, E. A. El Shenawy Prof. Dr., Ahmed M. Salem Dr

Journal of Engineering Research

Recently, CFD has offered a technological solution for modelling multi-phase flow in which we can make endless simulations with reduced expenses and effort in high accuracy results; we shall also mention that experimental studies have limitations for safety considerations when experimenting with flow in high temperature or pressure values or medium nature as in nuclear or chemical flows.In this paper, we used the ANSYS FLUENT CFD program to simulate the two-phase flow in a pipe to study the effect of attaching a 90-degree elbow fitting to the piping system, seeking to find out the change in the pattern and resulting …

Recent Advances In Solar Photo(Electro)Catalytic Nitrogen Fixation, Jun-Bo Ma, Sheng Lin, Zhiqun Lin, Lan Sun, Chang-Jian Lin

Journal of Electrochemistry

Ammonia (NH₃) is an essential chemical in modern society. It is currently produced in industry by the Haber-Bosch process using H₂ and N₂ as reactants in the presence of iron-based catalysts at high-temperature (400–600 ^oC) and extremely highpressure (20–40 MPa) conditions. However, its efficiency is limited to 10% to 15%. At the same time, a large amount of energy is consumed, and CO₂ emission is inevitably. The development of a sustainable, clean, and environmentally friendly energy system represents a key strategy to address energy crisis and environmental pollution, ultimately aiming to achieve carbon neutrality. …

Exploring The Morphological Surface Resistance And Optical Absorption Of Thin Black Carbon Nanotube Films For Electronic And Optoelectronic Devices, Ziad Khalifa, Sameh Osama Abdellatif

Chemical Engineering

This study investigates the optical and electrical properties of thin black films of carbon nanotubes (CNTs) fabricated under various conditions to explore their potential integration as either a perfect broadband absorber or enhanced counter electrode. The study involves SEM measurements, surface resistance measurements, and UV–Vis. spectrometer analysis. The results show that the CNT thin films exhibit high electrical conductivity and strong light absorption across various wavelengths. Optically, we investigated the impact of varying the growth temperature and catalyst temperature on the absorption profile of the thin films. The fabricated and deposited CNTs showed broadband absorption spectra, reaching 92.8% of the …

The Roles Of Carbonaceous Wastes For Catalysis, Energy, And Environmental Remediation, Chi Huey Ng, Mohd Aizzan Mistoh, Siow Hwa Teo, Andrea Galassi, Hin Taufiq-Yap, Nancy Julius Siambun, Jurry Foo, Coswald Stephen Sipaut, Jeffrey Seay, Jidon Janaun

Chemical and Materials Engineering Faculty Publications

This article reviews recent studies about various generations of the carbon materials for their applications in energy and environmental remediation. The synthesis routes of the carbon materials including the condition parameters, interaction of precursors, dopants and carbon materials, as well as their physical/chemical properties are explicated first. Then, the application and mechanism of metal-free/metal-doped/non-metal-doped carbon materials are discussed in detail. Lastly, this review is ended with a summary and invigorating perspectives on the challenges and future directions at the forefront of the catalysis platform to take a step further for real application.

Biodiesel Transesterification Of Spent Coffee Grounds Using Dbu As A Catalyst: Using Dbu To Make Biodiesel From Coffee Grounds, Christopher Stepherson, Pericles Karras, Amy Ha, Phuc Tan Nguyen, Abigail Pati, Jacob Hejazi, Soheil Hussain, Elizabeth De Young, Shuaicheng Fu

The Journal of Purdue Undergraduate Research

Coffee is one of the most universally consumed beverages. The world produces 60 million tons of spent coffee grounds (SCGs) as waste per year. Biodiesel made from SCGs is an eco-friendly alternative fuel but proves difficult to produce. 1,8-Diazabicyclo[ 5.4.0]undec-7- ene (DBU) was used as both a solvent and a catalyst with methanol to determine the efficiency of biodiesel production from SCGs. The process was completed by extracting coffee oil from acid-washed spent coffee grounds (AWSCGs) using hexane. The two extraction methods that were explored were Soxhlet and agitation. DBU is an interesting choice as a solvent and a catalyst …

Monodispersed Cu-Tcpp/Cu2O Hybrid Microspheres: A Superior Cascade Electrocatalyst Toward Co2 Reduction To C2 Products, Zi-Xuan Wan, Aidar Kuchkaev, Dmitry Yakhvarov, Xiong-Wu Kang

Journal of Electrochemistry

The electrochemical conversion of carbon dioxide (CO₂) into valuable chemicals is a feasible way to mitigate the negative impacts of overmuch CO₂ emissions. Porphyrin-based metal organic frameworks (MOFs) are expected to be used for selective and efficient electrochemical CO₂ reduction (ECR) with porous structure and ordered active sites. Herein, we report the synthesis of a monodispersed and spherical organic/inorganic hybrid Cu-TCPP@Cu₂O electrocatalyst composed of Cu-TCPP (TCPP=tetrakis (4-carboxyphenyl) porphyrin) and Cu₂O, where TCPP plays significant roles in regulating the morphology. In-situ formed Cu during ECR process in combination with Cu-TCPP (Cu-TCPP@Cu) can suppress …

Rational Design Of Heterostructured Nanomaterials For Accelerating Electrocatalytic Hydrogen Evolution Reaction Kinetics In Alkaline Media, Hai-Bin Ma, Xiao-Yan Zhou, Jia-Yi Li, Hong-Fei Cheng, Ji-Wei Ma

Journal of Electrochemistry

Owing to the merits of high energy density, as well as clean and sustainable properties, hydrogen has been deemed to be a prominent alternative energy to traditional fossil fuels. Electrocatalytic hydrogen evolution reaction (HER) has been considered to be mostly promising for achieving green hydrogen production, and has been widely studied in acidic and alkaline solutions. In particular, HER in alkaline media has high potential to achieve large-scale hydrogen production because of the increased durability of electrode materials. However, for the currently most prominent catalyst Pt, its HER kinetics in an alkaline solution is generally 2–3 orders lower than that …

Process Optimization For Syngas Production From The Dry Reforming Of Methane Over 5ni+3sr/10zr+Al Catalyst Using Multiple Response Surface Methodology, Ahmed Al-Fatesh Dr., Mai H. Roushdy, Radwa El-Salamony Dr., Saba Alwan Dr., Ahmed Osman Dr., Sadeq Al-Faresh Dr., Hamid Ahmed Dr., Anis Fakeeha Dr., Ahmed Ibrahim Dr.

Chemical Engineering

5Ni+3Sr/10Zr+Al catalyst is synthesized using the impregnation method, characterized, and tested for dry reforming of methane. The influence of reaction temperature, feed ratio (CO2/CH4), and gas hour space velocity are examined using multiple response surface methodology through three factors in, a four-level central composite design. Second and higher-order regression models are applied to evaluate the interaction between the process parameters and responses. The results indicate that the reaction temperature is the most influential followed by the space velocity, while the feed ratio has a weak effect. The optimum values that maximize each of the response variables are found to be …

Process Simulation For Converting Co2 Emissions From The Cementindustry To Dimethyl Ether, Nour Abou Seada, Dina Aboelela

Biochemical Engineering

Climate change is the leading severe problem in the twenty-first century, which is associated with greenhouse gas emissions,carbon dioxide that is the foremost cause of global warming and super greenhouse effect. In this concern, to avoid hazardousproblems, the steady stream of CO2 effluents existing in the atmosphere must be transformed to beneficial products for beingused as an abundant chemical feedstock. Implementing a new green strategy, which is known for the catalytic hydrogenationof CO2 into alternative fuels and valuable chemicals, will be a long-lasting solution to alleviate CO2 emissions. In this paper,a process simulation showing the synthesis of dimethyl ether (DME) …

Hydrogen Production From Microbial Electrolysis Cells Powered With Microbial Fuel Cells, Dina Aboelela

Biochemical Engineering

No abstract provided.

Supported Metal Nanoparticle Synthesis: Precursor Deposition And Agglomeration At Support Surfaces, Edward H. Chandler Jr.

Theses and Dissertations

Catalysis is a critical component of the chemical manufacturing industry. For example, it has been estimated to be essential to more than 90% of the major industrial processes developed during the middle years of the 20^th century.¹ Heterogeneously supported transition metal catalysts in particular have many benefits such as easy separability from the reaction mixture and high thermal stability. One method of synthesizing these is wet impregnation, wherein a metal solution is brought into contact with an oxide- or carbon-based powder. Given optimal environmental conditions, a metal will adhere to the surface through electrostatic means in a process …

Lead-Free Perovskite/Metal Oxide Heterojunction Photocatalyst For Sustainable Toluene Oxidation, Zakarya Hazaea

Chulalongkorn University Theses and Dissertations (Chula ETD)

An important field of study is the ecologically benign synthesis of useful compounds such as benzaldehyde and benzyl alcohol from the organic contaminant toluene. Lead-free halide perovskites are excellent options for photocatalysis due to their exceptional photoelectric properties. Nonetheless, they have notable challenges, such as fast charge recombination and ineffective charge separation. In this work, we present a simple anti-solvent technique to create a heterojunction between lead-free halide perovskite Cs2AgBiBr6 (CABB) with Cu2O and Cu-Cu2O. This combination facilitates the photocatalytic activation of C(sp3)−H bonds, which in turn increases the oxidation of toluene. The Cu2O and Cu-Cu2O creating a Z-scheme heterojunction …

Advanced Synthesis And Rational Design Of Support Structures For Nobel Metal Heterogeneous Catalysis: Towards Enhanced Activity And Continuous Processes, Brian R. Clark

Theses and Dissertations

The field of catalysis has a wide-ranging impact. Our group has identified the constant need for improved catalytic activity in high-impact applications such as hydrosilylation and cross-coupling reactions. For these reactions, precious metal catalysts often exhibit markedly better performance than their counterparts, but they can be a significant process cost that decreases overall economic efficiencies. To address this challenge, we explored support structures that can enhance catalytic activity at low metal loadings and improve precious metal recovery through simple filtration. We found that a platinum on graphene nanoplatelet catalyst (PtGNP) synthesized via strong electrostatic adsorption with microwave irradiation (SEA-MW) exhibits …

Investigation Of Space Charge Effects On Co2 Electrocatalytic Reduction On Gd-Doped Ceria Via Scanning Kelvin Probe And Model-Based Bayesian Analysis, Alejandro Mejia

Graduate Theses, Dissertations, and Problem Reports (ETD)

In studying novel energy conversion and storage systems, such as high-temperature electrolysis, numerous underlying fundamental physical processes remain unclear or inadequately understood. Among these, the modeling and comprehension of surface reaction mechanisms, coupled with the intricate effects of space‑charge interfaces, remains an unclear and challenging area of research.

The work of this dissertation involves the development of a 2D finite element analysis model, leveraging the robust MOOSE framework from INL. This model, featuring inhomogeneous defect thermodynamics for near-surface chemistry, formulated through Poisson‑Cahn variational theory, has been exploited for studying the electrocatalytic reduction of CO₂ on gadolinia doped ceria. The …

Sustainable Materials For Environment − Multifunctional Material Made From Dead Leaves And Nanostructured Materials For Antibiotic Degradation, Siyuan Fang

Dissertations, Master's Theses and Master's Reports

As environmental pollution from industrial processes and human activities continues to rise, finding efficient approaches to recycle waste materials and degrade persistent contaminants becomes increasingly critical. Dead leaves, an abundant but underutilized biomass, present an opportunity for creating value-added materials if their biocomponents can be preserved and transformed. Simultaneously, antibiotics such as tetracycline are widely found in water bodies but pose serious ecological and health risks, necessitating effective degradation methods. This dissertation addresses these challenges by leveraging natural and nanostructured materials to develop multifunctional products and advanced photocatalytic processes.

Chapter 3 of this dissertation addresses the challenge of converting waste …

Schaeffler Icvd Coating Machine, Louis Mcgrath

Williams Honors College, Honors Research Projects

Chemical Vapor Deposition (CVD) is mutual technology used to deposit thin film through a gaseous phase by vaporizing the solid materials. This conventional process usually requires high thermal stability of the materials, which is not applicable for most of the polymeric materials. Therefore, a novel process, initiated Chemical Vapor Deposition (iCVD) is developed by introducing the gaseous monument and initiator to form the thin film in-situ. By adjusting the free-radical polymerization in the vapor phase, a variety of thin and uniform polymer films can be achieved. Depending on the chemistry, iCVD has many categories. This report explains the design …

Change Of Metal Oxidation State At High Temperature, Impact Of Temperature And Reactive Gases, Yegor Nikitin

Dissertations and Theses

The fundamental understanding of gas-solid reactions enables a wide range of applications to be developed and improved. Specifically, the use of metal-based materials is critical to ensuring robust, safe, and long-term operations. For example, in power systems where boilers are used to generate steam for heat or electricity generation the use of stainless metal alloys is critical to allow high quality steam to be produced in a very harsh environment. Alternatively, in catalysis, the use of metal doped heterogeneous catalysts are essential in achieving selectivity and conversion performance for chemical synthesis to emissions abatement. Typically, these metal alloys must withstand …