Open Access. Powered by Scholars. Published by Universities.®

Catalysis and Reaction Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Discipline
Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 1261 - 1290 of 1364

Full-Text Articles in Catalysis and Reaction Engineering

Electro-Oxidation Of Phenol On Sno2/Ti Electrodes Prepared By Thermal Oxidation, Qing-Song Zhang, Hui-Huang Wu Nov 1999

Electro-Oxidation Of Phenol On Sno2/Ti Electrodes Prepared By Thermal Oxidation, Qing-Song Zhang, Hui-Huang Wu

Journal of Electrochemistry

A SnO2/Ti electrode prepared by thermal oxidation was used as the anode for galvanostatic electrolysis in acidic solution containing phenol, the time-dependances of phenol concentration, chemical oxygen demand in solution(COD) and instantaneous current efficiency were determined during electrolysis. The results show that with the SnO2/Ti anode instead of Pt, the COD significantly decreases at the same charge passage, and average current efficiency of oxidation increases by three times. The mechanism for phenol oxidation at two electrodes was discussed.

Go to article

Studies On Methods Of Fuel Cells Electrodes Preparation, Jun Gu, Sheng Sui, Guang-Qiang Li, Zhitong Sui Nov 1999

Studies On Methods Of Fuel Cells Electrodes Preparation, Jun Gu, Sheng Sui, Guang-Qiang Li, Zhitong Sui

Journal of Electrochemistry

In fuel cells, the structure of electrodes is an important factor which effect the cell performance. To improve the structure and the performance of electrodes, a new method of providing fuel cell electrodes is proposed in this paper. PTFE (polytetrafluoroethylene) and ethyne black was ground for about half an hour in a high-speed grinder, then the catalyst was added into the grinder and milled for an hour. This milled catalyst was transferred into a mixer followed by the addition of surface-active agent. After a suspension was formed, it was filtered under vacuum condition.Then a thin uniform filter-cake of the catalyst …

Go to article

Study On Electrochemical Reduction Properties Of Nitrobenzene, Chu-Na Ma, Wen-Kui Zhang, Hui Huang, Yong-Ping Gan Nov 1999

Study On Electrochemical Reduction Properties Of Nitrobenzene, Chu-Na Ma, Wen-Kui Zhang, Hui Huang, Yong-Ping Gan

Journal of Electrochemistry

The electrochemical reduction characteristics of nitrobenzene was extensively investigated by using the techniques such as quasi-steady-state polarization, cyclic voltammetry, fast linear potential sweep method and chronoamperometry in this paper. The electroanalytic properties of Cu, Cu-Hg and Cu-Ni electrodes were evaluated. Based on the study of the transient steping behaviour of nitrobenzene to PAP, the reduction mechanism was discussed. The results showed that the transition steps existed on the electrochemical reduction of nitrobenzene in acidic solution, the reactant is also absorbed on electrodes surface. The control step in the reduction of nitrobenzene was ascribed to the diffusion of nitrobenzene and its …

Go to article

High Performance Proton Exchange Membrane Fuel Cells, Jing-Rong Yu, Bao-Lian Yi, Ming Han, Xiao-Liang Cheng, Zhi-Gang Shao, Jing-Xin Zhang Nov 1999

High Performance Proton Exchange Membrane Fuel Cells, Jing-Rong Yu, Bao-Lian Yi, Ming Han, Xiao-Liang Cheng, Zhi-Gang Shao, Jing-Xin Zhang

Journal of Electrochemistry

Proton-exchange membrane fuel cells(PEMFC) using a perfluorosulfonic acid proton exchange membrane as an electrolyte can simplify water and electrolyte management. In this paper, the effects of thickness of PEM on the performance of PEMFC were studied. The Nafion-112 PEM and low platinum loading E-TEK electrode yielded very high power density, of the order of 0.95 W/cm2. The energy-conversion efficiency, the degree of platinum utilization and stability for PEMFC using Nafion 112 and E-TEK electrode were also investigated.

Go to article

Investigation Of Sodium Hypophosphite Anodic Oxidizing Behavior In The Process Of Acid Electroless Nickel Deposition, Mei-Yuan Wang, Ya-Fei Kuang, Yan Xu Nov 1999

Investigation Of Sodium Hypophosphite Anodic Oxidizing Behavior In The Process Of Acid Electroless Nickel Deposition, Mei-Yuan Wang, Ya-Fei Kuang, Yan Xu

Journal of Electrochemistry

The anodic oxidizing behavior of sodium hypophosphite in the process of electroless nickle deposition (pH=5.5) was investigated with the linear potential sweep method and alternating current impedance. The results indicated that, the oxidation of NaH2PO2 was a complicated electrochemical process and affected by the concentration of NaH2PO2, the temperature of the bath, the sweep rate and the existence of nickel ion. The NaH2PO2 electrooxidation reaction was very likely preceded by heterogeneous interface transformation process, which might be the control step of the whole anodic process.

Go to article

Electrochemical Synthesis Of Fes Electrode And Its Behavior Measurement, Cong-Sheng Guan Aug 1999

Electrochemical Synthesis Of Fes Electrode And Its Behavior Measurement, Cong-Sheng Guan

Journal of Electrochemistry

The Potential for the electrochemical synthesis of FeS electrode has been obtained by cyclic voltammetry. FeS electrodes were synthesiaed by controlling Fe electrode at -1.0 V in LiCl-KCl-Li2S and Li(FClI)-Li2S melts and their behavior were measured also. The FeS electrode synthesized in molten Li(FClI)-Li2S has the best charge and discharge properties.

Go to article

Deactivation Of Nickel Oxide/Hydroxide To Electrooxidation Of H2Po2 Anions On Nickel Electrodes In Alkaline Solutions, Tai-Xiang Jiang, Hui-Huang Wu Aug 1999

Deactivation Of Nickel Oxide/Hydroxide To Electrooxidation Of H2Po2 Anions On Nickel Electrodes In Alkaline Solutions, Tai-Xiang Jiang, Hui-Huang Wu

Journal of Electrochemistry

Electrooxidation of hypophosphite anions on polycrystalline nickel in alkaline solutions has been investigated by cyclic voltammetry and open circuit potential measurements. The results are explained based on the mechanism that the first step of hypophosphite oxidation is the adsorption of hypophosphite ions on nickel, followed by the homolysis of its hydrogen bond with the formation of radicals. The oxidation of hypophosphite on nickel in alkaline medium occurs at lower potentials between ca. -0.8 V— -1.1 V (SCE) and phosphite ion is the only oxidation product. There is no indication of hypophosphite oxidation at higher potentials. Severe deactivation of the surface …

Go to article

Structural And Electrochemical Studies On Lithium Manganese Oxide Containing Li+ Prepared By Hydrothermal Method For Lithium Ion Batteries, De-Yao Liu, Jin-Kua You, Wei Chu, Yong Yang, Zu-Geng Lin Aug 1999

Structural And Electrochemical Studies On Lithium Manganese Oxide Containing Li+ Prepared By Hydrothermal Method For Lithium Ion Batteries, De-Yao Liu, Jin-Kua You, Wei Chu, Yong Yang, Zu-Geng Lin

Journal of Electrochemistry

In this paper, Todorokite manganese oxides containing Li+ with large tunnel structure (sample M5) have been synthesized by hydrothermal methods from natural manganese oxide nano fiber (sample M4). The structure and composition of the samples were characterized and analyzed by XRD, ICP, TGA and DTA. Its electrochemical behavior as a cathode materials for rechargeable lithium ion insertion were studied by galvanostatic charge/discharge measurements. XRD results show that the sample M4 is mainly composed of Birnessite and Vernadite structure. Although the sample M4 shows a high initial capacity of approximately 150 mAh/g, its performances decrease gradually over 30 cycles. It …

Go to article

The Techniques Of The Paired Electrosynthesis, Hong-Kun Zhang, Deng-Ping Gu Aug 1999

The Techniques Of The Paired Electrosynthesis, Hong-Kun Zhang, Deng-Ping Gu

Journal of Electrochemistry

In this Paper, we introduce our work on paired electrosynthesis. In conjunction with our research practice, we introduce electrolytic conditions,such as material of electrode ,courrent density and electrolytic temperature etc,as reference for researcher. We categorize the paired electrosynthesis techniques to widen our view on the paired electroorganic synthesis and to promote the deveopments of paired electrosynthesis techniques.

Go to article

Study On Synthesizing Of 2-Methylbutanoic Acid By Indirect Electrooxidation, Chong-Tao Zhao, Ze-Shan Zhu Aug 1999

Study On Synthesizing Of 2-Methylbutanoic Acid By Indirect Electrooxidation, Chong-Tao Zhao, Ze-Shan Zhu

Journal of Electrochemistry

The working conditions of synthesizing 2-methylbutanoic acid by oxidizing 2-methyl-1-butanol with tetrabutylammonium hydrosulfate (TBAS) or tetrabutylammonium perchlorate (TBAP) as phase transfer catalyst in sulfuric acid Cr(Ⅵ) oxidation medium was studied. The Cr(Ⅵ) oxidation medium could be electrolytic regenerated from Cr(Ⅲ), during above oxidation reaction. Under the optinum condition, the yield of 2-methylbutanoic acid is more than 95%.

Go to article

The Ac-Impedance Analysis For Pluse Oxide Film Of Aluminium Alloy, Ai-Ling Du, Xi-Cheng Ma, He-Ming Zhang Aug 1999

The Ac-Impedance Analysis For Pluse Oxide Film Of Aluminium Alloy, Ai-Ling Du, Xi-Cheng Ma, He-Ming Zhang

Journal of Electrochemistry

Bode diagrams for aluminum PC (abbreviated from pulse current) oxide films were first obtained by AC-impedance measurements in a wide range of frequency. The experimental results show that different kinds of electrical equivalent circuits can be used for representing PC films and DC (abbreviated from direct current) oxide films separately, the main differences between them are their porous layers, the PC films are more even with little defects.Those are also verified by SEM and V-I characteristic curve measurements.

Go to article

Influence Of Ptfe And Nafion On The Utilization Efficiency Of Pt/C Catalyst In Pemfc, Xiao-Liang Cheng, Bao-Lian Yi, Jing-Xin Zhang, Ming Han, Ya-Guang Qiao May 1999

Influence Of Ptfe And Nafion On The Utilization Efficiency Of Pt/C Catalyst In Pemfc, Xiao-Liang Cheng, Bao-Lian Yi, Jing-Xin Zhang, Ming Han, Ya-Guang Qiao

Journal of Electrochemistry

With cycling voltammetry curve(C-V), TEM and SEM photographs, the influence of PTFE and Nafion on the platinum utilization in catalyst layer of PEMFC was investigated. The results show that in gas diffusion electrode, the blocking effect of PTFE in the platinum utilization is not pronunced. In the thin-film catalyst layer, the electron conduct of the catalyst was blocked by the nafion solid and this caused the decrease of platinum utilization. With the increase of the nafion content in the catalyst layer, both platinum utilization and the electron conductivity decreased in the catalyst layer. Because the molecule size of nafion is …

Go to article

Oxidation And Adsorption Of Deoxyribonucleic Acid At Highly Ordered Pyrolytic Graphite And Glass Carbon Electrode, Jian-Zhang Zhou, Ling-Ling Wu, Jin Luo, Zhong-Hua Lin May 1999

Oxidation And Adsorption Of Deoxyribonucleic Acid At Highly Ordered Pyrolytic Graphite And Glass Carbon Electrode, Jian-Zhang Zhou, Ling-Ling Wu, Jin Luo, Zhong-Hua Lin

Journal of Electrochemistry

It is shown that calf thymus DNA (CT DNA) can be adsorbed at highly ordered pyrolytic graphite (HOPG) electrode and detected by differential pulse voltammetry (DPV) and electrochemical atomic force microscopy (ECAFM). It is found that controlled potential pre-polarization influences largely the adsorption of dsDNA while it has little influence on ssDNA. It is demonstrated that ECAFM is useful to exploit adsorption of DNA at HOPGE. The pattern of adsorption of DNA at HOPG electrode that fits best with the experimental data is proposed. The results aslo shows that UV/Vis reflection spectroscopy, which has not been used in studying electrochemical …

Go to article

Reversal Flow In Fixed-Bed Reactors Operating Under Reaction-Regeneration Cycles, Daniel O. Borio, Noemi S. Schbib, Jorge E. Gatica May 1999

Reversal Flow In Fixed-Bed Reactors Operating Under Reaction-Regeneration Cycles, Daniel O. Borio, Noemi S. Schbib, Jorge E. Gatica

Chemical & Biomedical Engineering Faculty Publications

The unsteady state simulation of a set of industrial fixed-bed reactors is presented. The catalytic dehydrogenation of 1-butene into 1-3-butadiene is selected as case study. These reactors operate under reaction-regeneration cycles. Each stage of the process, i.e., dehydrogenation (deactivation by coking), steam purge, oxidative regeneration and evacuation, is simulated by means of the corresponding dynamic model. The kinetic parameters used in the dehydrogenation and regeneration stages for a Cr2O3/Al2O3 catalyst are taken from the literature. The performance of the reactors is investigated for two different operation modes: conventional …

Go to article

Studies Of Electrochemical Characteristics Of Pasted Nickel Hydroxide Electrode With Surface Deposited Cobalt, Xian-You Wang, Yun-Shi Zhang, Jie Yan, Zheng Zhu, Hua-Tang Yuan, De-Ying Song Feb 1999

Studies Of Electrochemical Characteristics Of Pasted Nickel Hydroxide Electrode With Surface Deposited Cobalt, Xian-You Wang, Yun-Shi Zhang, Jie Yan, Zheng Zhu, Hua-Tang Yuan, De-Ying Song

Journal of Electrochemistry

The surface of the spherical nickel hydroxide particles used as an active material in pasted nickel electrodes is surface-deposited with cobalt. This paper investigated the effects of the amount of cobalt deposit on the characteristics of nickel hydroxide electrode. The performances of the electrode, such as discharge capacity, utilization of active material and reversibility of Ni(OH)2/NiOOH redox reaction, were studied by comparing the charging/discharging curves and cyclic voltammograms. The mechanism of action of cobalt deposits has been described in terms of the electrochemical impedance spectroscopy of nickel hydroxide electrode.

Go to article

Kinetic Study Of Electrooxidation Of Benzene, Xin-Sheng Zhang, Ping Ding, Ying-Chun Dai, Wei-Kang Yuan Feb 1999

Kinetic Study Of Electrooxidation Of Benzene, Xin-Sheng Zhang, Ping Ding, Ying-Chun Dai, Wei-Kang Yuan

Journal of Electrochemistry

A reaction kinetic study for electrochemical oxidation of benzene was performed on a PbO2 rotating disk electrode in 1 mol/L H2SO4 aqueous solution. The reaction orders, the activation energies and transfer coefficient were measured, and the kinetic expression was obtained.

Go to article

Oxidation Mechanism Of Hypophosphite, Dong-Bai Sun, Ying Jin, Hong-Ying Yu, De-Jun Yang Feb 1999

Oxidation Mechanism Of Hypophosphite, Dong-Bai Sun, Ying Jin, Hong-Ying Yu, De-Jun Yang

Journal of Electrochemistry

There exist two oxidation current peaks on the anodic polarization curve between -0.7 V and 0 V (SCE) in Na-hypophosphite solution. Peak Ⅰ (-0.55 V, SCE) , which represents the oxidation process from H2PO2- to H2PO3-, has been studied previously. Peak Ⅱ, which is located at the potential about -0.4 V (SCE), is investigated emphatically in this paper. The results show that, peak Ⅰ and Ⅱ are corresponding to two successive steps in oxidation process of H2PO2-, i.e. peak Ⅱ corresponds to the oxidation process of …

Go to article

Synthesis And Application Of Polymeric Corrosion Inhibitor For Reinforced Concrete, Wei-Wei Lin, Sheng-Xian Wang, Jian-Qing Zhang, Jun Yuan, Zhen-Guo Ji Feb 1999

Synthesis And Application Of Polymeric Corrosion Inhibitor For Reinforced Concrete, Wei-Wei Lin, Sheng-Xian Wang, Jian-Qing Zhang, Jun Yuan, Zhen-Guo Ji

Journal of Electrochemistry

A new polymer E-T was synthesized and used as a corrosion inhibitor for reinforced concrete. The inhibitive behavior and mechanism were studied with linear polarization, Tafel polarization, EIS and XPS method in simulated pore solution system with concrete samples. The result showed that the polymer was a mixing type inhibitor. A 1% dosage was sufficient to imhibit the corrosion of steel in simulated pore solution system. The salt endurance was enhanced from 0.02 mol/L to 0.10 mol/L. The result also showed the good synergetic effect of NaNO2, especially in low NaNO2 concentration. The EIS showed that E-T …

Go to article

A New Cell Structure For Proton Exchange Membrane Fuel Cell, Ming Han, Hong-Feng Xu, Bao-Lian Yi Feb 1999

A New Cell Structure For Proton Exchange Membrane Fuel Cell, Ming Han, Hong-Feng Xu, Bao-Lian Yi

Journal of Electrochemistry

Separating the functions of current collection and gas flow distribution and then to design two separate elements to achieve the desired performance characteristics, a nonconventional cell structure for proton exchange membrane fuel cells bave been developed. The current collector is achieved using a thin stain steel sheet, the gas flow distribution is achieved using a carbon paper that has the desired chemical durabiliy when in contact with the proton exchange membrane. Combining these two separate elements into a single divice yields a bifunctional device that performs as a bipolar separator plate. The advantages of this alternative appproach to making biplar …

Go to article

Oxygen Transfer In A Three-Phase Fluidised Bed Bioreactor With Novel Biomass Support When Used In Industrial Wastewater Treatment, S Manyele, Dec 1998

Oxygen Transfer In A Three-Phase Fluidised Bed Bioreactor With Novel Biomass Support When Used In Industrial Wastewater Treatment, S Manyele,

Tanzania Journal of Engineering and Technology (TJET)

The effect of support mass and liquid height on the oxygen transfer in the three- phase fluidised bed were experi/nenta/ly investigated. Novel biomass support, rhe KMT*, with density of 850 kg/n/ and an equivalent size, dp 8.3 mm, has been used in this work. The oxygen transfer rate was expressed in terms of rhe volumetric oxygen transfer coefficient, kca. It has been found out that the* a values increased with increasing support mass up to a critical solids load of 4.0 kg, above which the kca decreased and that kca decreased with increasing liquid height. It has been recommended that …

Go to article

Turbulent Burning Model For Premixed Gaseous Mixtures, E Mushi Dec 1998

Turbulent Burning Model For Premixed Gaseous Mixtures, E Mushi

Tanzania Journal of Engineering and Technology (TJET)

A turbulent burning model for premixed gaseous mixtures has been successfully developed. The model assumes instant burning of vortex Tubes of the order of Kolmogorov scale followed by burning of larger eddies of the order of Taylor micro scale. These eddies burn ar a rate dependent On the stretch rate. The influence of turbulence on the burning rate is introduced in the form of probability density function which gives the probability that a given mixture under turbulence will undergo burning rather than being quenched. The model has been validated againsi experiments involving turbulent explosions in a fan stirred bomb. Model …

Go to article

New Technologies For Thermal Disposal Of Sewage Sludge, T Ogada Dec 1998

New Technologies For Thermal Disposal Of Sewage Sludge, T Ogada

Tanzania Journal of Engineering and Technology (TJET)

The traditional methods for the disposal of sewage sludge are landfilling, recycling as fertilisers in agricultural lands, dumping into sea and incineration. In thc recent past, Sludge incineration has been rapidly gaining ground duc to environmental constraints facing the Other methods. However, the cost of pollution control during sewage sludge incineration is currently very high due to the expensive flue gas treatment facility required. Futhermore, large quantity Of ash is produced which is highly contaminated with heavy metals and must be disposed off in special landfilling sites in order to avoid ground water pollution. To reduce the cost Of pollution …

Go to article

Experimental Study Of Domestic Charcoal Stoves, Simbo Kimario Dec 1998

Experimental Study Of Domestic Charcoal Stoves, Simbo Kimario

Tanzania Journal of Engineering and Technology (TJET)

The demand of fuelwood for domestic cooking especially the charcoal fuel is increasing in the urban settlements due to the increase in population of low income class earners who are the main consumers Of this type of fuel. This paper is presenting rhe results Of experiments conducted on the popularly used domestic charcoal stoves in Tanzania. The results revealed some significant differences on stoves performances. The type of insulation materials and some design features incorporated into the combustion chambers of the stoves had positive impacts in relative charcoal fuel saving. About two tons of charcoal fuel could be saved by …

Go to article

The Significance And Effects Of Oil Injection On The Performance Of Sliding Vane Compressors., M Mkumbwa Dec 1998

The Significance And Effects Of Oil Injection On The Performance Of Sliding Vane Compressors., M Mkumbwa

Tanzania Journal of Engineering and Technology (TJET)

A computer model of a sliding vane air compressor was used to predict the behaviour of machines having different geometries operating at different conditions. The performance parameters which were calculated by the model were the free air delivery, power input and specific capacity which is defined as the free air delivery per unit of power input.The model also included the study of the effects of Oil injection on these mentioned compressor performance parameters. The paper describes the simulation model developed incorporating an analysis Of the effects of the oil injected into the compressor on lhe thermodynamic processes taking place in …

Go to article

A Study On Ring Pack Lubrication In Internal Combustion Engine, I Mshoro Dec 1998

A Study On Ring Pack Lubrication In Internal Combustion Engine, I Mshoro

Tanzania Journal of Engineering and Technology (TJET)

Most efthe lubricating oil from Internal Combustion Engine (ICE) is lost through piston rings. Hence, in order to optimally reduce ICE oil consumption, a better insight into tribology of the ring pack is required. This can only be achieved by an inwroved characterization of the lubricant behaviour within the opelating environment of the engine. In The present ieork, an optical tcchnique using laser- induced fluorescence was employed to measure oil film thickness within the ring pack. The experiment was conducted on a Phaser 1000 Series engine, whereby optical access to the ring pack was achieved by a fused silica-window positioned …

Go to article

The Latest World Wide Progress In Solid Oxide Fuel Cell, Yi Jiang Nov 1998

The Latest World Wide Progress In Solid Oxide Fuel Cell, Yi Jiang

Journal of Electrochemistry

Solid oxide fuel cell (SOFC) is a novel, green electricity generation technology, which has been showing rapid development since 1980's. In light of its high efficiency, environmental friendly, fuel adaptability and long term stability, the Research, Development and Demonstration (RD&D) of this hype of full cell have been emphasized in a large number of developed countries. Based on the information communicated at the latest symposium on SOFC held last year in Aachen (Germany) and the knowledge gained through years of research in this field, a comprehensive review on the latest development of the tubular, this planar SOFC as well as …

Go to article

A Preliminary Study Of The Synthesis Of Tin-Based Amorphous Material And Its Behavior On Lithium Intercalation, Li Liu, Han-Xi Yang, Ju-Tang Sun, Xing-Ping Ai Nov 1998

A Preliminary Study Of The Synthesis Of Tin-Based Amorphous Material And Its Behavior On Lithium Intercalation, Li Liu, Han-Xi Yang, Ju-Tang Sun, Xing-Ping Ai

Journal of Electrochemistry

An amorphous lithium inserting anode material based on Tin oxide glass was synthesized by salification in solution and its properties on lithium intercalation was investigated by X ray diffraction (XRD), microelectrode voltammetry and charge discharge measurements. The results have shown that this kind of material has considerable electrochemical reversibility toward lithium intercalation deintercalation. The available discharge capacity of the material reaches 430 mAh/g with charge-discharge efficiency over 90%, showing a great potential for practical use.

Go to article

Direct Electro-Oxidation Synthesis Of D-Arabinose On Spectroscopic Graphite Electrode, Hei Wei, Huang Ying Nov 1998

Direct Electro-Oxidation Synthesis Of D-Arabinose On Spectroscopic Graphite Electrode, Hei Wei, Huang Ying

Journal of Electrochemistry

D Arabinose synthesized by direct electro-oxidative decarboxylation of D gluconate on graphite electrode from aqueous solutions. The effects of D gluconate concentration, electrolysis potential, temperature and electrolyte composition on the current efficiency and product yield of electrosynthsis are discussed. The laboratory scale electrosynthesis was achieved with flow through cell. The optimum technology conditions for electrosynthesis were obtained with orthogonal design method. Both galvanostatic and potentionstatic conditions have been exploited, the later was found to be more effective.

Go to article

Study On Electrosynthesis Of Butyl Butyrate At Conducting Oxide Anode Support On Titanium, Jun-Xiang He, Jin-Cheng Zhou, Kang-Ning Chen Nov 1998

Study On Electrosynthesis Of Butyl Butyrate At Conducting Oxide Anode Support On Titanium, Jun-Xiang He, Jin-Cheng Zhou, Kang-Ning Chen

Journal of Electrochemistry

Synthesis of butyl butyrate by direct electroxidation of n butyl alcohol and the electrochemical behaviors of several selected conducting oxide electrodes (Pb/PbO2, Ti/PbO2, i/SnO2+Sb2O3/PbO2 and Ti/SnO2+Sb2O3+PdOx/PbO2) have been investigated. The results demonstrated that the intermediate layers of SnO2, Sb2O3 and PdOx could significantly decrease the interfacial resistance of the electrodes, and that the Ti/SnO2+Sb2O3+PdOx/PbO2 electrode possessed better electrocatelytic performance than others.

Go to article

Primary Research Of Reversible Proton Exchange Membrane Regenerative Fuel Cells, Zhi-Gang Shao, Bao-Lian Yi, Ming Han Nov 1998

Primary Research Of Reversible Proton Exchange Membrane Regenerative Fuel Cells, Zhi-Gang Shao, Bao-Lian Yi, Ming Han

Journal of Electrochemistry

In this paper, we report the results of our studies on regenerative proton exchange membrane fuel cell (RPEMRFC) catalysts, electrode preparation and their performances. The Pt catalyst for the oxygen electrode was replaced by 60 w%Pt + 40 w%IrO2 which reduces polarization by 0.2 V in a polymer protone exchange membrane fuel cell. The cycle performance of RPEMRFC was found to be manly effected by the stability of the diffiusion layer of bifunctional oxygen electrode.

Go to article

First Prev Next Last