Mechanical Engineering Commons^™

An Advanced Controller For A Semi-Active Wheelchair Suspension, David J. Smith

Master's Theses

An Advanced Controller for a Semi-Active Wheelchair Suspension was designed, built and tested.  The suspension consisted of a Goodyear 1S3-011 air spring, IQ Valves high speed proportional solenoid valve, and a custom made accumulator.  Several controller designs specific to semi-active suspensions were designed and tested.  The controllers investigated were skyhook, acceleration driven damping, and a combined control law employing both a dual and single sensor version.  The implementation of skyhook control suffered performance degradation from the idealization due to particular elements of hardware, however acceleration driven damping showed a marked and statistically significant improvement over skyhook control, in hardware, by …

The Design And Modification Of A Sputter System For Dc Reactive Sputtering Of Alumina And Zirconia Thin Films, Diane Van Ho

LSU Master's Theses

Yttria-stabilized zirconia (7% YSZ) is the most used material for thermal barrier coatings (TBCs) to reduce the conductive heat transfer on turbine blades, but it is not resistant to infrared radiation. In order to reduce radiation heat transfer, alternating materials, such as alumina and zirconia, can be used to fabricate multi-layer coatings in which each layer is optimized to reflect a targeted range of wavelength. This research aims to fabricate these multi-layer coatings by reactive magnetron sputtering. Reactive magnetron sputtering is the sputtering of an elemental target in the presence of a reactive gas that will react with the target …

Testing And Characterization Of Second-Order Differential Microphones, Joshua H. Merlis

Graduate Dissertations and Theses

The focus of this thesis is the testing and characterizing of directional microphones, designed based on the ear of the fly Ormia ochracea. The response of these microphones is modeled as a linear combination of the gradients of the sound field. A least squares approach is employed in order to determine the transfer functions between the response and these gradients. Knowledge of these complex transfer functions is crucial in understanding the nature and quality of the response of these microphones.

Once determined, these transfer functions are used to simulate the plane wave response of differential microphones. This process is invaluable …

Test 1999a: John Deere 8335rt My12, Nebraska Tractor Test Lab

Nebraska Tractor Tests

ABOUT THE TEST REPORT AND USE OF THE DATA The test data contained in this report are a tabulation of the results of a series of tests. Due to the restricted format of these pages, only a limited amount of data and not all of the tractor specifications are included. The full OECD report contains usually about 30 pages of data and specifications. The test data were obtained for each tractor under similar conditions and therefore, provide a means of comparison of performance based on a limited set of reported data. EXPLANATION OF THE TEST PROCEDURES Purpose The purpose of …

Beading And Dimpling Techniques To Improve The Vibration And Acoustic Characteristics Of Plate Structures, Nabeel Taiseer Alshabtat

Dissertations

A method of improving the vibroacoustic characteristics of beams and plates is presented. This method is based on creating dimples or beads on the surface of the structures. The proposed method couples the finite element method with an optimization technique based on the genetic algorithm (GA). The improvement of the vibroacoustic characteristics of beams and plates is achieved by two separate strategies. The first strategy is optimizing the natural frequencies of beams and plates. The second strategy is minimizing the sound radiation from such vibrating structures. Optimizing the natural frequencies of some types of beams and simply supported plates by …

Ductile Mode Material Removal Of Ceramics And Semiconductors, Deepak Ravindra

Dissertations

Ceramics and semiconductors are hard, strong, inert and lightweight. They also have good optical properties, wide energy bandgap and high maximum current density. This combination of properties makes them ideal candidates for tribological, semiconductor, MEMS and optoelectronic applications respectively. Manufacturing these materials without causing surface and subsurface damage is extremely challenging due to their high hardness, brittle characteristics and poor machinability. However, ductile regime machining of these materials is possible due to the high-pressure phase transformation occurring in the material caused by the high compressive stresses induced by the single point diamond tool tip. In this study, to further augment …

Gas Turbine Blade Tip And Near Tip Heat Transfer With Film Cooling, Gregory Kramer

LSU Master's Theses

Gas turbine blade tips experience very high thermal loads due to high temperature combustion gases and tip leakage flows. This leads to the tip region being very susceptible to experiencing failures. To better understand these effects, experiments were performed in a suction-type low speed wind tunnel cascade to determine heat transfer coefficients and film cooling effectiveness distributions on a highly-loaded 2-D gas turbine blade model in the tip and near-tip regions. The blade shape was generated to match the pressure coefficients of the operating turbine blade design. The model featured multiple tip and pressure side film cooling holes and a …

Development Of Measurement Methods For Testing Of Hydrokinetic Devices To Evaluate The Environmental Effect On Local Substrate, Michael Volpe

Honors Theses

Modifications and upgrades to the hydraulic flume facility in the Environmental Fluid Mechanics and Hydraulics Laboratory (EFM&H) at Bucknell University are described. These changes enable small-scale testing of model marine hydrokinetic(MHK) devices. The design of the experimental platform provides a controlled environment for testing of model MHK devices to determine their effect on localsubstrate. Specifically, the effects being studied are scour and erosion around a cylindrical support structure and deposition of sediment downstream from the device.

Performance Characteristics Of Airlift Pumps With Vortex Induced By Tangential Fluid Injection, Jacob Riglin

Honors Theses

The effect of the swirl component of air injection on the performance of an airlift pump was examined experimentally. An airlift pump is a device that pumps a liquid or slurry using only gas injection. In this study, the liquid used was water and the injected gas was air. The effect of the air swirl was determined by measuring the water discharge from an airlift pump with an air injection nozzle in which the air flow had both axial and tangential components and then repeating the tests with a nozzle with only axial injection. The induced water flow was measured …

Design Of A Liquid Fuel Injector For Alternative Fuel Studies In An Atmospheric Model Gas Turbine Combustor, John Stevenson

Honors Theses

A new liquid-fuel injector was designed for use in the atmospheric-pressure, model gas turbine combustor in Bucknell University’s Combustion Research Laboratory during alternative fuel testing. The current liquid-fuel injector requires a higher-than-desired pressure drop and volumetric flow rate to provide proper atomization of liquid fuels. An air-blast atomizer type of fuel injector was chosen and an experiment utilizing water as the working fluid was performed on a variable-geometry prototype. Visualization of the spray pattern was achieved through photography and the pressure drop was measured as a function of the required operating parameters. Experimental correlations were used to estimate droplet sizes …

Analytical Investigation Of Squeeze Film Dampers, Mehmet Murat Altuğ Biҫak

Dissertations, Master's Theses and Master's Reports - Open

Squeeze film damping effects naturally occur if structures are subjected to loading situations such that a very thin film of fluid is trapped within structural joints, interfaces, etc. An accurate estimate of squeeze film effects is important to predict the performance of dynamic structures.

Starting from linear Reynolds equation which governs the fluid behavior coupled with structure domain which is modeled by Kirchhoff plate equation, the effects of nondimensional parameters on the damped natural frequencies are presented using boundary characteristic orthogonal functions. For this purpose, the nondimensional coupled partial differential equations are obtained using Rayleigh-Ritz method and the weak formulation, …

Control Design And Genetic Algorithm Optimization For Electrostatic Mems, Jill C. Blecke

Dissertations, Master's Theses and Master's Reports - Open

This dissertation discusses structural-electrostatic modeling techniques, genetic algorithm based optimization and control design for electrostatic micro devices.

First, an alternative modeling technique, the interpolated force model, for electrostatic micro devices is discussed. The method provides improved computational efficiency relative to a benchmark model, as well as improved accuracy for irregular electrode configurations relative to a common approximate model, the parallel plate approximation model. For the configuration most similar to two parallel plates, expected to be the best case scenario for the approximate model, both the parallel plate approximation model and the interpolated force model maintained less than 2.2% error in …

Length Of The Annular Regime For Condensing Flows Inside A Horizontal Channel - The Experimental Determination Of Its Values And Its Trends, Patcharapol Gorgitrattanagul

Dissertations, Master's Theses and Master's Reports - Open

The experiments observe and measure the length of the annular regime in fully condensing quasi-steady (steady-in-the-mean) flows of pure FC-72 vapor in a horizontal condenser (rectangular cross-section of 2 mm height, 15 mm width, and 1 m length). The sides and top of the duct are made of clear plastic that allows flow visualization. The experimental system in which this condenser is used is able to control and achieve different quasi-steady mass flow rates, inlet pressures, and wall cooling conditions (by adjustment of the temperature and flow rate of the cooling water flowing underneath the condensing-plate). The reported correlations and …

Estimating Industrial Building Energy Savings Using Inverse Simulation, Franc Server, J. Kelly Kissock, Dan Brown, Steve Mulqueen

Mechanical and Aerospace Engineering Faculty Publications

Estimating energy savings from retrofitting existing building systems is traditionally a time intensive process, accomplished by developing a detailed building simulation model, running the model with actual weather data, calibrating the model to actual energy use data, modifying the model to include the proposed changes, then running the base and proposed models with typical weather data to estimate typical energy savings. This paper describes a less time-intensive method of estimating energy savings in industrial buildings using actual monthly energy consumption and weather data. The method begins by developing a multivariate three-parameter changepoint regression model of facility energy use. Next, the …

Estimation Of The Centre Of Mass From Motion Capture And Force Plate Recordings: A Study On The Elderly, Sebastien Cotton, Michele Vanoncini, Philippe Fraisse, Nacim Ramdani, Emel Demircan, Andrew P. Murray, Thierry Keller

Mechanical and Aerospace Engineering Faculty Publications

The estimation of the centre of mass position in humans is usually based on biomechanical models developed from anthropometric tables. This method can potentially introduce errors in studies involving elderly people, since the ageing process is typically associated with a modification of the distribution of the body mass. In this paper, an alternative technique is proposed, and evaluated with an experimental study on 9 elderly volunteers. The technique is based on a virtual chain, identified from experimental data and locating the subject's centre of mass. Its configuration defines the location of the centre of mass, and is a function of …

Computational Investigation Of Particle Settling Effects On Inhaled Submicron Bioaerosol Deposition In The Human Lung, Mohammed Ali, Essam A. Ibrahim

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 1-5

Dynamic Modeling And Parameter Estimation For Impact Analysis And Robust Packaging Design, Thomas M. Stone, Seung-Kyum Choi, Hemanth Amarchinta

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 6-13

Asme Early Career Technical Journal (Front Matter), Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. -x

Motion Tracking Through Machine Vision, Poonam Savsani, Vimal Savsani

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 14-21

Significance Of Mwcnt And Tio2 Nanofillers On Low-Density Polyethylene Thermal & Mechanical Properties: Applicability For Pipes Used In Water & Energy Systems, Erin E. Mcdonald, Gail D. Jefferson, Andrew J. Whelton, Tinh Nguyen

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 22-26