Mechanical Engineering Commons^™

Asme Human Powered Vehicle, Benjamin Knaus, Philip Basmadjian, Nick Supat

Mechanical Engineering

Speed Solutions has been contracted to design and build a Human Powered Vehicle (HPV) frame and drivetrain for the Cal Poly HPV club to use in their 2011 race season. This project is being funded by the Cal Poly HPV club and their sponsors. The goal is to design, test and build a bicycle frame that the HPV club can attach to a fairing of their design. Primary design considerations will include speed, weight, cost, rider ergonomics, reliability and ease of repair. This vehicle will be used to compete in ASME’s Human Powered Vehicle Challenge (HPVC) series of races.

Adapted Recumbent Bike, Kurtis Mundell, Dane Tiemeier, Laura Yakuma, Darius Yu

Mechanical Engineering

The adapted recumbent project was to redesign a disabled veteran’s recumbent bicycle.  The main areas of concern were the crank pedal, chain tension, braking and steering system, and ergonomics. Since the customer is an avid biker, this bike will be used often, so the design is based on the ease of repair and replacement.  The crank system was redesigned to a lightweight, adjustable part with chain clearance and high strength. The chain tension was improved by replacing the existing single idler wheel/chain tube system with a dual idler wheel system. The dual idler has a titanium sprocket in one of …

Pulse Echo Ultrasonic Testing Of Adhesive Bonded Joints For Automotive Applications, Arun Ganapathi

All Theses

The growing prominence of adhesive bonding technology in automotive manufacture has necessitated the development of reliable and robust quality assurance techniques. Of the different Nondestructive testing technologies available, Ultrasonic testing has shown itself to be the most promising technique to satisfy the requirements in automobile production. The current work attempts to apply two variations of the Ultrasonic Pulse Echo technique namely Contact and Immersion testing for inspecting typical hem bonded automotive joints. The joints have been tested for disbond at the various metal-adhesive interfaces by using an ultrasonic scan comparison method which compares the acquired signals against a reference scan …

An Investigation Of Initially Delaminated Composite Sandwich With Delamination Arrest Mechanism Under Buckling Loading, Tony D. Tran

Master's Theses

This thesis involves the development of a fiberglass-foam composite sandwich structure with the introduction of delamination arrestment keys; therefore, a study of an initially delaminated composite sandwich structure was the experimental analysis on multiple configurations in how the arrestment keys are placed.

The first part of this thesis research was to the experimental design and manufacturing of the composite sandwich plates. These plates were later cut down to the specific test dimensions and manufacturing processes for the composite sandwich plates and test specimens were created. The composite sandwich plates were manufactured using a vacuum resin infusion process. The dimensions of …

Bi-Material Attachment Through A Soft Tissue Interfacial System, Y. X. Liu, S. Thomopoulos, Victor Birman, J. S. Li, G. M. Genin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

No abstract provided.

The Cd-Te Phase Diagram, Robert F. Brebrick

Mechanical Engineering Faculty Research and Publications

The properties of the liquid phase in the Cd–Te system are fit using thermodynamic properties of CdTe(c) recently optimized by the author. These include a high temperature heat capacity significantly lower than commonly used such that the enthalpy of formation of CdTe(c) at its melting point is about 10 kJ/mol less negative than previously thought. An associated solution model with Cd, CdTe, and Te species is used. Seven adjustable parameters are sufficient to quantitatively fit the liquidus and partial pressures of Te₂ and Cd. Additional partial pressures for Te rich CdTe(c) near its melting point are extracted from an …

Hybrid Nanomanufacturing Process For High-Rate Polymer Nanofiber Production, Chad T. Peterson

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Nanotechnology and nanomaterials have the potential to revolutionize existing and create entirely new industries. Unique physical, mechanical, chemical, and biological properties of nanomaterials have been extensively documented in the last two decades. However, most nanomaterials are discontinuous in nature, creating problems with their processing and manipulation into devices and raising health concerns. Continuous nanofibers represent an emerging class of nanomaterials with critical advantages to applications. Continuous nanofibers are readily produced by electrospinning process comprising spinning polymer solutions in high electric fields. Electrospinning is a very economic top-down nanomanufacturing process that has been used to produce ultrafine continuous nanofibers from several …

Robot Crawling Device And Tee Table, Todd P. Trauman, Kyle M. Colvin, David Charles Fantz

Mechanical Engineering

As golf becomes a more frequently enjoyed activity, equipment manufacturers such as Hot Stix Golf require updated testing mechanisms to actively compete in their respective markets. One such testing device is a golfing robot nicknamed the “Iron Byron”. Two issues were asked to be addressed for the senior project. First, the robot was practically immobile unless taken apart and moved with a forklift. The request from Hot Stix was to mobilize the robot so that it could easily be transported with minimal use of external help. Secondly, the initial tee-table was both poorly-designed and missing altogether. The new tee-table needed …

Water Well Drilling Rig Final Project Report, Alexander (Alex) Wargnier, Thad Jablonski, Coel Schumacher

Mechanical Engineering

In this report, the improvements of a previously produced cable tool drilling rig are described. The purpose of the rig is to drill water wells for use in Africa in order to provide safe drinking water to many in need. An affordable, effective, and controllable rig is the design goal for this project. With the San Luis Obispo Rotary Club sponsoring the project the design team of WHole Engineering have made necessary design choices to manufacture the product. Actions performed include background research of existing drilling technologies, analysis of top concepts for the controlling mechanism, and selection for the final …

The Quadricycle Hand And Foot Cycle, Marissa Chin, Parker Drennan, Spencer Nelson, Kevin Reidy

Mechanical Engineering

This report documents the design process from concept generation to manufacturing for a hand and foot powered cycle named the Quadricycle.  The Quadricycle project is a joint effort at California Polytechnic State University in San Luis Obispo between the Mechanical Engineering and Kinesiology Departments.  The project objectives are to design a portable cycle that can be powered by hands and feet simultaneously in order to provide recreation and rehabilitation for a person with a disability.  This project is funded under a grant by the National Science Foundation (NSF).

2-D Path Planning For Direct Laser Deposition Process, Swathi Routhu, Divya Kanakanala, Jianzhong Ruan, Xiaoqing Frank Liu, Frank Liou

Computer Science Faculty Research & Creative Works

The zigzag and offset path have been the two most popular path patterns for tool movement in machining process. Different from the traditional machining processes, the quality of parts produced by the metal deposition process is much more dependent upon the choice of deposition paths. Due to the nature of the metal deposition processes, various tool path patterns not only change the efficiency but also affect the deposition height, a critical quality for metal deposition process. This paper presents the research conducted on calculating zigzag pattern to improve efficiency by minimizing the idle path. the deposition height is highly dependent …

Me-Em Enewsbrief, December 2010, Department Of Mechanical Engineering-Engineering Mechanics, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

The Effects Of Roof Solar Absorptance On Building Energy Performance In A Variety Of U.S. Climate Zones, Zachary Eubanks

Mechanical Engineering Undergraduate Honors Theses

The solar absorptance of a roof surface directly affects the solar heat gain through the roof. It has been shown that buildings in hot climates benefit from roofs with low absorptance. Cold and moderate climates have received less attention in previous studies. This paper simulates the effects on annual energy use, carbon dioxide emission, and utility cost of varying the solar absorptance of warehouse and small office building roofs in a wide variety of U.S. climate zones using EnergyPlus software and the DOE Commercial Building Benchmark Models. Results show that the optimum absorptance not only depends on the climate zone, …

Design And Implementation Of An Actively Adjustable Spring Mechanism Via Redundant Actuation, Eleazar Marquez

Theses and Dissertations - UTB/UTPA

This study presents the theoretical results and experimental validation of an adjustable stiffness mechanism. The use of redundant actuation is emphasized in the design of a one-degree-of-freedom Watt II mechanism capable of independently controlling the effective stiffness without a change in equilibrium position. This approach is in contrast to previous spring mechanism designs unable to actively control the spring rate independent of deflection, and has potential applications in various types of suspension and assembly systems. Results indicate that driving the redundantly actuated, unidirectional, spring mechanism requires attaching two direct brush-type direct current motors on each of the two grounded revolute …

A Study Of The Effect Of Vibration On Railroad Bearing Temperature, Bertha Alicia Gonzalez

Theses and Dissertations - UTB/UTPA

An on-track collaborative field test and laboratory experiments were conducted in order to determine the relationship between abrupt rises in surface temperature of a railroad bearing and vibration signatures captured during the experiments. The collaborative field test was conducted in order to investigate the root cause for this abrupt temperature change known as bearing temperature trending. The research presented in this thesis will show that temperature trending is correlated to an increase in the magnitude of vibration within the bearing and the fundamental frequencies that are generated by the internal components of a rotating bearing assembly. Distinct vibration mechanisms are …

Photonic Crystal Design And Fabrication Assisted By Tunable Femtosecond Oscillator Laser, Kristofer B. Ohlinger

Theses and Dissertations - UTB/UTPA

Photonic Crystals have the potential for engineered light interaction as directed by the photonic bandgap, a property that details the prohibited propagation region and ultimately the ability to guide light. A so called, photonics-on-chip, would incorporate arbitrary light guiding with functional elements in one package. The realization of such a device is subject to the fabrication paradigms implemented and this thesis is concerned with holographic lithography as a means for creating polymer photonics crystal templates and two-photon polymerization for incorporating light guiding pathways.

In this thesis, the design of the to-be-fabricated structures has been co-opted by computational exploration of the …

College Of Engineering Senior Design Competition Fall 2010, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge.

The senior design competition helps to focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects …

Mobility Aid: A Dual Purpose Walker And Scooter, Zack Blois, Robia Choi, Kristin Dills

Mechanical Engineering

The Mobility Aid project was proposed by Theresa Mortilla and Idee Shapiro. The goal of the project was to design and build a device that can quickly and easily transform between a mobility walker and an electric scooter to allow for more freedom of mobility. The inspiration for this project arose from the fact that Theresa suffers from multiple sclerosis in her legs and can only walk for about thirty minutes at a time until she gets too fatigued and must sit down and rest. This device would provide her with the ability to continue moving while giving her legs …

Foam Wars Ii, Sumant Advani, Sivadas Menon, Casey Pieplow

Mechanical Engineering

The team producing Foam Wars II consists of three Mechanical Engineering students and five Kinesiology students (three the first two quarters and two the last quarter) at California Polytechnic State University, San Luis Obispo. The project is the second iteration of Foam Wars as a senior project at Cal Poly, sponsored by Dr. Kevin Taylor under the National Science Foundation grant. Persons with disabilities often feel limited when it comes to recreational activities and Foam Wars would provide them with an outlet to interact and engage themselves in a group setting. The game consists of various wheelchair attachments that would …

Universal Play Frame Vi, Justin Bazant, Cullen Crackel, Anthony Franceschi

Mechanical Engineering

This design report details the design process utilized by Adaptive Exercise Designs (AED) in creating the sixth design of the Universal Play Frame (UPF). The UPF is an adaptive frame which supports a variety of devices that allows athletes in wheelchairs with limited range of motion to participate in physical activity. The past five frame designs do not meet the needs of the Friday Club due to complications with function and time constraints. To ensure all of Fridays Club's needs were met, the problem was better defined by converting the customer requirements into engineering specifications. The design process our team …