Computer-Aided Engineering and Design Commons^™

Quickcut Cnc Waterjet Cutter, Kelly V. Robbins

Williams Honors College, Honors Research Projects

This design project was dedicated to improving the existing design and making functional the QuickCut CNC Waterjet Cutter. The scope of work consisted of making the machine mobile and more structurally stable as well as programming the CNC controls. The project was started in the 2018/19 school year by a former mechanical engineering student. The subsystems consist of the frame, power, motor, water pump and associated plumbing, nozzle, abrasive feed system, x/y gantry, Arduino control system and the cutting bed. Unfortunately, due to the COVID-19 pandemic, the full scope was not able to be completed in its entirety.

Rinse Tank Salinity Automation, George Pahoundis

Williams Honors College, Honors Research Projects

Manufacturing processes are often consisted of many different processes and sub-processes. Each of these carries its own level of importance and impact to the overall picture. In this particular sub-process, salt is rinsed from a product via a rinse tank: a tank whose salinity may not exceed a certain level and whose temperature must not fall below a certain level. This setting is a prime opportunity to implement an automated control system to allow these parameters to be met with upmost efficiency. With potential savings in excess of $20,000 per year and an estimated payback period of 8 weeks, the …

Design And Optimization Of Dynamic System For A One-Kw Free Piston Linear Engine Alternator-Gensets Program, Nima Zamani Meymian

Graduate Theses, Dissertations, and Problem Reports (ETD)

In power/energy systems, free-piston linear machines are referred to as a mechanism where the constrained crank motion is eliminated and replaced with free reciprocating piston motion. Depending on the application, the piston motion can be converted into other types of energy and includes compressed air/fluid, electricity, and high temperature/pressure gas. A research group at West Virginia University developed a free-piston linear engine alternator (LEA) in 1998 and have achieved significant accomplishment in the performance enhancement of the LEAs to date. The present LEA design incorporates flexure springs as energy restoration components and as bearing supports. The advantages of using flexure …

High Tech, High Risk: Tech Ethics Lessons For The Covid-19 Pandemic Response, Emanuel Moss, Jacob Metcalf

Publications and Research

The COVID-19 pandemic has, in a matter of a few short months, drastically reshaped society around the world. Because of the growing perception of machine learning as a technology capable of addressing large problems at scale, machine learning applications have been seen as desirable interventions in mitigating the risks of the pandemic disease. However, machine learning, like many tools of technocratic governance, is deeply implicated in the social production and distribution of risk and the role of machine learning in the production of risk must be considered as engineers and other technologists develop tools for the current crisis. This paper …

Peridynamic Approaches For Damage Prediction In Carbon Fiber And Carbon Nanotube Yarn Reinforced Polymer Composites, Forrest E. Baber

Theses and Dissertations

Aerospace structures are increasingly utilizing advanced composites because of their high specific modulus and specific strength. While the introduction of these material systems can dramatically decrease weight, they pose unique certification challenges, often requiring extensive experimental testing in each stage of the design cycle. The expensive and time-consuming nature of experimental testing necessitates the advancement of simulation methodologies to both aid in the certification process and assist in the exploration of the microstructure design space.

Peridynamic (PD) theory, originating from Sandia National Lab’s in the early 2000’s, is a nonlocal continuum-based method that reformulates the equation of motion into an …

Strategies And Devices For Improving Respiratory Drug Delivery To Infants And Children With Cystic Fibrosis, Karl Bass

Theses and Dissertations

Cystic Fibrosis (CF) is a degenerative disease, which causes thickening of the airway surface liquid and reduced mucociliary clearance, which provides an ideal habitat for bacterial infections. Early treatment of CF in children can prevent chronic infection, improve quality of life, and increase life expectancy. The most predominant bacteria found in CF-diseased lungs is Pseudomonas aeruginosa (Pa), which can be treated with inhaled tobramycin. Excipient enhanced growth (EEG) powder formulations are well suited for administering tobramycin to children, as the EEG approach provides minimal upper airway loss and targeted drug delivery. This method uses an initially small aerosol for high …

Real-Time Instance Segmentation And Point Cloud Extraction For Japanese Food Using Rgb-D Camera, Suthiwat Yarnchalothorn

Chulalongkorn University Theses and Dissertations (Chula ETD)

Innovation in technology is playing an important role in the development of food industry, as is indicated by the growing number of food review and food delivery applications. Similarly, it is expected that the process of producing and packaging food itself will become increasingly automated using a robotic system. The shift towards food automation would help ensure quality control of food products and improve production line efficiency. One key enabler for such automated system is the ability to detect and classify food object with great accuracy and speed. In this study, we explore real-time food object segmentation using RGB-D depth …

Autonomous Guided Vehicle Frame For Outdoor Use, Thomas Mcgrath

Williams Honors College, Honors Research Projects

The overall goal for my project is to design a durable Autonomous Guided Vehicle (AGV) frame intended for carrying a heavy load over outdoor terrain. I will not be designing a complete vehicle, only the basic structure that can be used to build a complete AGV on. There will be complete 3D models of the design and its individual parts. I also would like to provide limited Finite Element Analysis of the design using ANSYS software to determine weaknesses and methods for improvement. The design I create is meant to be used as a framework for complete outdoor AGV designs. …

Design Of Banner Tow Mechanism For Bush Plane, Kyle Ciarrone, Ivan Martin, Rishabh Gadi, Tyler Brandt

Williams Honors College, Honors Research Projects

The 2019-2020 AIAA DBF objective was to design, build, and test a banner-towing bush plane that carries wooden passengers and luggage. Senior members on the team undertook the creation of the banner tow mechanism subsystem as their senior design project on behalf of the design team due to the challenge of its mechanical design and the aerodynamic considerations regarding its placement and enclosure aboard the aircraft. The competition as well as access to campus resources were canceled due to COVID-19, so full testing and integration of the mechanism was not achieved. However, the engineering design process was experienced from the …

Custom 3d Printed Orthotic, Dakota Kirtley, Andrew Wiles

Williams Honors College, Honors Research Projects

The goal of this senior design projet is to develop a cutsom 3D printed orthotic shoe insert. Pressure mapping, laser scanning, and 3D modeling will be used to create a truly custom orthotic for each foot. Pressure mapping will give the weight distribution on an individual's food and the laser scanner will give the x-y coordinates of the foot. these two together will be used to generate a a 3D model which will then be 3D printed to create a custom orthotic. Research and material testing will also be done to determine the best material type to be used in …

A Commercial Apartment Complex, Kathleen A. George

Williams Honors College, Honors Research Projects

Within this project the similarities and differences of new and used heating, cooling, and plumbing systems and equipment will be compared and contrasted in depth. Doing so would help further knowledge and understanding of the design field and help to foster quicker decision making in an educated way. The questions to be answered are: in which stage of this project did the client have the best equipment (the high-end outcome) and why, in which stage did they have the cheapest equipment (the low-end outcome) and why, in which stage did they have the best equipment while also being cost efficient …

Generative Design In Energy Efficient Buildings, Johanna Thill

Dissertations, Master's Theses and Master's Reports

This is an investigative report on the use of generative design and genetic algorithms in the design of energy-efficient buildings. It focuses on a workflow using Project Refinery© and Dynamo© in Revit® for multi-objective optimization and visualization, and Honeybee© for daylighting analysis. The workflow was not about to run completely due to instability in Dynamo, however daylighting analysis and visualizations were produced separately from demonstrations of Refinery. It concludes that while genetic algorithms have potential to be useful in energy-efficient building design, these programs are not yet fully developed and difficult to use without extensive background knowledge and fluency in …

Sensitivity And Uncertainty Quantification Of Continuum And Stochastic Bond Dissociation Kinetics Based Cohesive Laws, Rishabh Awasthi

Dissertations, Master's Theses and Master's Reports

Polymeric adhesives are being extensively used to develop light weight and durable Composite Materials which are have been employed in automotive, aeronautical, medical industry. Polymeric adhesives undergo failure due to relative opening sliding of bonded interfaces which requires a need to characterize the fracture mechanism. Numerous experiments are conducted to predict the fracture response for Mode-I, II,III and numerical simulations are employed to inversely calibrate the material parameters governing the constitutive laws. Cohesive zone models are largely employed in fracture mechanics to predict failure of interfaces undergoing large plastic deformations. The objective of this report is to employ the cohesive …

Buckling Load Study On Pop Nut (Rivet) Using Finite Element Analysis, Saurabh Shankar Shegokar

Dissertations, Master's Theses and Master's Reports

This study highlights the material behavior in riveting operation that includes buckling load analysis using ABAQUS. Finite Element Analysis is used to find the buckling load vs. Displacement results and validated with the results obtained in physical testing of rivet (POP Nut). A mesh sensitivity study is performed using ABAQUS to understand the optimum mesh size for this analysis. An axisymmetric model with contact properties is created and simulated to reduce the simulation time using ABAQUS. The results obtained through Finite Element Analysis show a good resemblance with the testing results. Design changes were suggested to achieve better results that …

A Study Of Model-Based Control Strategy For A Gasoline Turbocharged Direct Injection Spark Ignited Engine, Xin Wang

Dissertations, Master's Theses and Master's Reports

To meet increasingly stringent fuel economy and emissions legislation, more advanced technologies have been added to spark-ignition (SI) engines, thus exponentially increase the complexity and calibration work of traditional map-based engine control. To achieve better engine performance without introducing significant calibration efforts and make the developed control system easily adapt to future engines upgrades and designs, this research proposes a model-based optimal control system for cycle-by-cycle Gasoline Turbocharged Direct Injection (GTDI) SI engine control, which aims to deliver the requested torque output and operate the engine to achieve the best achievable fuel economy and minimum emission under wide range of …

The Potentials Of Faecal Sludge Treatment Using Local Conditioners In Tanzania: A Review, Doglas Benjamin1

Tanzania Journal of Engineering and Technology (TJET)

Worldwide, every day human beings generate millions of tons of Faecal Sludge (FS), which is rich in water, nutrients, energy, and organic compounds. Yet FS is not being managed in a way that permits us to derive value from its reuse, while at the same time, millions of farmers struggle with depleted soils and lack of water. In most of the developing countries, energy for cooking is mainly derived from cutting of trees, either as wood or charcoal. Resource recovery and reuse from FS can create livelihoods, enhance food security, support green economies, reduce waste and contribute to cost recovery …

Enhanced Heat Transfer Performance By Shape Optimization Of A Non-Axisymmetric Droplet Evaporating On A Heated Micropillar, Haotian Wu

McKelvey School of Engineering Graduate Student Theses & Dissertations

Abstract

Enhanced Heat Transfer Performance by Shape Optimization of a Non-axisymmetric Droplet Evaporating on a Heated Micropillar

By

Haotian Wu

Department of Mechanical Engineering and Materials Science

Washington University in St. Louis, 2019

Research Advisor: Professor Damena Agonafer

The stacked multilayer 3D IC structure used in next generation high-powered electronics poses great challenges in dissipating their large heat flux, which causes extreme difficulties for traditional cooling technologies. In response, more advanced two-phase liquid cooling technologies, such as droplet evaporation, which utilizes the latent heat of vaporization to remove excessive heat, have been widely investigated. Compared to traditional single-phase cooling techniques, …

Static Analysis Of Circular Plates Under Mechanical Loads, Harpreet Lalia

Publications and Research

In this research statics analysis of circular plates is performed using SolidWorks.

Circular plates with different material properties, thickness to radius ratios, and boundary conditions under mechanical loads are modeled and analyzed in SolidWorks.

The results are obtained for deflections of circular plates under uniform and point loads.

A three-dimensional (3D) model of circular plates is first created in SolidWorks. Then the material properties, mechanical loads and boundary conditions are defined for the plate.

It is found deflection of plates is depended on magnitude of mechanical loads, geometrical parameters, boundary conditions and material properties. Responses of SolidWorks for deflections of …

Hybrid Iii 95th Percentile Large Male Finite Element Model Neck Alteration, Eric Riley Day

Master's Theses

The motivation behind the project was to update the Livermore Software Technology Corporation (LSTC) Hybrid III 95th percentile finite element model, such that the neck assembly response under varying simulated loading conditions equals that of the federally regulated Hybrid III 95th percentile anthropomorphic testing device (ATD).

The family of Hybrid III crash test dummies approximate the physical properties and response of the human body in a frontal automotive crash. The Hybrid III is used to assess the effectiveness of vehicle restraint systems. LSTC offers Hybrid III finite element models for use in their Multiphysics simulation software package, LS-DYNA. The Hybrid …

Deployable Cover For Cubesat Fuv Imager, Edwin J. Rainville, Patrick J. Rainville, Jeff Wagner

Mechanical Engineering

The goal is to develop a deployable cover for a far ultraviolet imager cube satellite that will be used to map the earth’s auroras in the ionosphere. The deployable cover is used to protect the Far Ultra-Violet (FUV) sensor and lenses, house two mirrors which are used to filter unwanted light and expose optics when deployed. The deployable cover consists of a door, an actuator, a lockout mechanism, and an “open position” indicator. This project also includes designing a fixture for testing the optical alignment of the deployable cover after launch and during orbital conditions. The subassembly is required to …