Computer-Aided Engineering and Design Commons^™

Deep-Sea Water Collector, Chandler Jones, Jenny Verheul, Michael Di Giorgio

Mechanical Engineering

Properties such as nutrients, DNA, pH levels, and primary productivity are difficult to measure onboard an Underwater Remotely Operated Vehicle (UROV) as mobile submarine sensors are highly expensive and conventional water capture devices are too large to be equipped. However, these properties provide an integral view into our oceans, the species that inhabit them, and our influence on the environment. Collected samples of seawater taken back to labs allow researchers to see a clearer picture of ecosystems’ inhabitants and lifecycle with the analysis of Environmental DNA (eDNA) among many other properties. The scope of this project is to design a …

Modular Attachment System For Tactical Robot, Michelle K. Chandler, Jacob A. Nelson, Adam V. Ivelia, Quang Truong

Mechanical Engineering

The goals of this report are to clearly define the problem and the scope of this project, present information regarding background design research, explain the process taken to reach the final design, go over the part procurement and manufacturing process, outline the assembly steps, and verify the design against the criteria through testing. The problem and scope of the project were defined using the constraints provided by the project sponsor, Blueline robotics. Blueline needs a modular attachment system for their tactical robot. The completed background research contains existing robot solutions that deal with similar tasks. Many of these existing robots …

Resistive Switching In Fto/Cuo-Cu2o/Au Memory Devices, Amir Shariffar, Haider Salman, Tanveer A. Siddique, Wafaa Gebril, M. Omar Manasreh

Electrical Engineering Faculty Publications and Presentations

Memristors are considered to be next-generation non-volatile memory devices owing to their fast switching and low power consumption. Metal oxide memristors have been extensively investigated and reported to be promising devices, although they still suffer from poor stability and laborious fabrication process. Herein, we report a stable and power-efficient memristor with novel heterogenous electrodes structure and facile fabrication based on CuO-Cu2O complex thin films. The proposed structure of the memristor contains an active complex layer of cupric oxide (CuO) and cuprous oxide (Cu2O) sandwiched between fluorine-doped tin oxide (FTO) and gold (Au) electrodes. The fabricated memristors demonstrate bipolar resistive switching …

Agent-Based Modelling Of Values: The Case Of Value Sensitive Design For Refugee Logistics, Christine Boshuijzen-Van Burken, Ross J. Gore, Frank Dignum, Lamber Royakkers, Phillip Wozny, F. Leron Shults

VMASC Publications

We have used value sensitive design as a method to develop an agent-based model of values in humanitarian logistics for refugees. Schwartz’s theory of universal values is implemented in the model in such a way that agents can make value trade-offs, which are operationalized into a measure of refugee wellbeing and a measure of public opinion about how the refugee logistics is being handled. By trying out different ‘value scenarios’, stakeholders who are responsible for, or involved in refugee logistics can have insights into the effects of various value choices. The model is visualized and made usable as a platform …

Development Of An Augmented Reality Based Facility Layout Planning And Optimization, Tan Chee Hau

Student Works (2020-2029)

This study presents an augmented reality (AR) based facility layout planning (FLP) system with an optimization algorithm to assist facility layout designers in decision making. AR is a technology that blends virtual data such as 3 Dimensional (3D) model into the actual world. FLP is about the allocation of facilities to achieve smooth, efficient and effective processes. FLP’s research can be divided into the procedural approach, algorithmic approach, Virtual Reality (VR) and AR-based approaches. AR-based FLP effectively addressed the traditional FLP issues such as facilitating the addition of a new machine in an existing production floor, rearrangement of machines’ sequence, …

An Affordable And Portable Palpable System For Sensing Breast Tissue Abnormalities, Cody J. Clarke

Montview Journal of Research & Scholarship

Due to the high cost of equipment and lack of trained personnel, manual palpation is a preferred alternative breast examination technique over mammography. The process involves a thorough search pattern using trained fingers and applying adequate pressure, with the objective of identifying solid masses from the surrounding breast tissue. However, palpation requires skills that must be obtained through adequate training in order to ensure proper diagnosis. Consequently, palpation performance and reporting techniques have been inconsistent. Automating the palpation technique would optimize the performance of self-breast examination, optimize clinical breast examinations (CBE), and enable the visualization of breast abnormalities as well …

Homogenization Of Composite And Cellular Materials Incorporating Microstructure And Surface Energy Effects, Ahmad Gad

Mechanical Engineering Research Theses and Dissertations

In the last few decades, the popularity of composite and cellular materials has rapidly increased through their widespread applications in multiple engineering fields including aerospace, automotive, civil and biomedical. However, to a large extent, the success of their practical applications depends on our ability to predict their mechanical behavior by using high-fidelity mechanics models.

Micromechanical modeling of composite and cellular materials is a challenging task due to the heterogeneous nature of such materials and the interactions among various constituent phases at the microscopic level, which result in non-homogeneous deformation, strain and stress fields. Therefore, it is necessary to develop simple …

Formula Sae Monocoque Chassis Development, Kc Egger, Brian Ford, Kyle Nagao, Neal Sharma, Donovan Zusalim

Mechanical Engineering

Formula SAE is a collegiate competition hosted by SAE International with the primary goal being to design, manufacture, and race an open wheel race car. The Cal Poly Racing Formula SAE team strives for improvement every race season and has remained competitive as a result. The 2019-2020 management team determined that further research and development towards the chassis would yield the greatest performance benefit for future seasons, as the previous chassis platform limited packaging and mounting options for vehicle subsystems which interfaced with the chassis.

A redesign of the Cal Poly Racing Formula SAE team’s carbon fiber reinforced polymer monocoque …

Methods For Mass Data Acquisition Of Whiskey Webs., Adam D. Carrithers

Electronic Theses and Dissertations

Whiskey webs are a recently discovered phenomenon in which the monolayer collapse during evaporation of diluted American whiskey results in self-assembled, web-like structures. It was found that the pattern of weblike structures were unique between different American whiskey products. It is desirable to use these unique patterns as a “fingerprint” which can be used to identify whiskeys, their chemical constituents, and perhaps even counterfeits. In pursuit of identifying whiskey products based on their web pattern, it is necessary to have a large database of samples imaged for each product. The device discussed herein is the realization of an apparatus capable …

Analysis Of One Way Valve Mechanism For Wings Of A Flapping Drone, Xinchen Deng

Student Works (2020-2029)

The flapping drone is one type of MAVs which is defined as a miniature unmanned aerial vehicle that is inspired by flying birds and insects. Flapping wings can make a perfect combination of thrust and lift by flapping up and down with full usage of unsteady air. The flapping drone has the advantages of high maneuverability and a special lift generation mechanism. Compared with rotary-wing or fixed-wing MAV, it is smaller, lighter, and has higher flight performance. It can quickly change the flight direction and flight speed by control the flapping frequency and it is the only flight mode that …

Fluid Flow Analysis Of Low-Altitute Agricultural Uav Pesticide Spraying Device, Dan Han

Student Works (2020-2029)

The nozzle is an important part of the drone pesticide spraying device. The quality of the nozzle directly affects the atomization performance. Fan nozzles are widely used in the field of plant protection in agriculture, forestry, pest control, and weed removal. When using drones to spray pesticides, the spraying velocity, the spraying range of the pesticides, and the atomized particle size are all key factors that directly affect the efficiency of pesticide use. This paper uses SOLIDWORKS and ANSYS software to design and simulate. The boundary conditions are kept the same, and the influence of the nozzle's grooving angle (α), …

A Computational Study Of Water Mobility On Smooth Surface, Cavities And Porous Structure With Hydrophilic And Hydrophobic Coatings, Kok Wee Yong

Student Works (2020-2029)

This research focus on water mobility and discovers a new phenomenon where droplet accelerates on a hydrophilic cavity surface when sliding down from a hydrophobic surface. The kinetic energy of droplet increases six (6) times higher than before sliding into the first cavity. This finding is useful for creating an effective way of filling liquids into cavities for passive microfluidics related devices. The work consists of validating cases using Computational Fluid Dynamics (CFD) software. The first part of the research reviews the literature regarding CFD modelling of a water droplet (i) sliding down on a surface, (ii) detachment in a …

Modeling Of Heavy Vehicle Braking Related To Accident Reconstruction For A Range Of Vehicle And Road Characteristics, Zamzamzadeh Mahdieh

Student Works (2020-2029)

In today's heavy-vehicle accidents, one of the major contributors is emergency braking, particularly for vehicles without an anti-lock braking system (ABS), which is dominant in developing countries like Malaysia. As the heavy vehicle driver applies emergency braking, there is a high chance of wheel lock-up, at which point the vehicle will skid along the road, creating braking marks from the tires. These braking marks are often used in crash reconstructions. Braking marks are mainly used by investigators to examine the vehicle's pre-impact velocity. There are many models and formulations based on kinetic energy that show the effect of some parameters. …

Cad For College: Switching To Onshape For Engineering Design Tools, Kate N. Leipold

Presentations and other scholarship

Engineering Design Tools aims to teach students to use industry standard CAD tools in the context of a design and build course. Previous versions of the course have been taught utilizing Creo Parametric. To alleviate install concerns, distributed team work, and the challenges of learning Creo in a short time frame, the class transitioned to utilizing Onshape. To quote the Onshape website - “Onshape is the first CAD system built for teams. Students can work in groups and edit models together simultaneously. Teachers can distribute assignments, review work and give feedback with ease. Additionally, Onshape keeps a complete history of …

Heavenly Bodies Rsvp, Justin Tyler Spitzer, Allison Jean Turnbaugh, Jack William Boulware, Braden Alex Lockwood

Mechanical Engineering

The purpose of the Heavenly Bodies RSVP project was to design and fabricate planet props, as well as a mechanism by which they could be raised and lowered in California Polytechnic State University’s Pavilion theater. The project team was comprised of four fourth year mechanical engineering students: Allison Turnbaugh, Braden Lockwood, Jack Boulware, and Justin Spitzer. We conducted extensive research to determine the ideal solution for the design problem brought to us by our sponsor. In our analysis, we discovered that the most important aspects of our design were the absolute reliability of the system, fire retardant material selection, and …

Elevate Dental, Connor Merrick, Everett Johnson, Jonah Holbrook

Mechanical Engineering

During a dental procedure, patients are often required to have a bite block placed in their mouths to keep them open for the duration of their procedure. These can be very uncomfortable for patients due to lack of properly-fitting sizes. This project presents an alternative fully adjustable bite block that is affordable, comfortable, and easy to use for dental personnel.The bite block is a two piece side loading design that uses interlocking teeth to supply a range of five sizes.

Vibration Isolation System, Bradley Y. Kwan, Bailey Groh, Max Wu, Nicole Yen

Mechanical Engineering

The Vibration Isolation System Senior Project is a collaborative group project between its sponsor, Maxar Technologies, and a team of students from Cal Poly - SLO to effectively design, manufacture, and test a structural assembly for satellites, isolating vibrations during launch and orbit conditions. After initial sponsor contact, requirements and needs were set which dictated deliverables for the senior project group. The group performed analyses to validate all design decisions, including a modified concept and design direction, selection of a prototype viscoelastic damping material, preliminary testing to validate design specifications, and detailed design and analysis toward a finalized design. Instead …

Simulating Particle Packing During Powder Spreading For Selective Laser Melted Additive Manufacturing Using The Discrete Element Method In Abaqus, Priscilla Ng

Master's Theses

Metal additive manufacturing allows for the rapid production of complex parts that are otherwise impractical using conventional subtractive manufacturing techniques. Applications for additive manufacturing span across a broad array of industries including aerospace, automotive, and medical, among many others. One metric of printing success is material properties, including part density. While there has been extensive research completed for the density of printed parts, there is little published work concerning powder packing density on the build plate associated with powder spreading.

In this thesis, a Discrete Element Method (DEM) model was created in Abaqus to simulate the spreading behavior of particles …

Reading Robot, Gillian Watts, Andrew Myers, Sabrinna Tan, Taylor Klein, Omeed Djassemi

General Engineering

Presently, there is an insufficient availability of human experts to assist students in reading competency and comprehension. Our team’s goal was to create an improved socially assistive robot for use by therapists, teachers, and parents to help children and adults develop reading skills while they do not have access to specialists. HAPI is a socially assistive robot that we created with the goal of helping students practice their reading comprehension skills. HAPI enables a student to improve their reading skills without an educator present, while enabling educators to review the student's performance remotely. Design constraints included: physical size, weight, duration …

Cp Check Valve Design, Alec B. Der Matoian, Jessica M. Dent, Skylar M. Tusting

Mechanical Engineering

This report is to serve as a final design review and update to the project sponsors at Zurn Wilkins for the Check Valve Design Senior Project. The senior project team was tasked with improving upon the design of Zurn Wilkins’ backflow prevention assembly for small diameter pipes by reducing the pressure loss created by the check valves within the double check backflow assembly. The information contained in this report builds off the information contained in the Critical Design Report (CDR), as well as feedback and further investigation suggested during an Intermediary Design Review. Based on conclusions from the CDR, our …