Computer-Aided Engineering and Design Commons^™

High Strollers, Braeden Hammond, Morley Perrin, Reid Bartels, Juan Rodriguez

Mechanical Engineering

This report documents the final product of Jonathon’s new lightweight stroller. The Mechanical Engineering team from Cal Poly, High Strollers, began the project to create a lightweight stroller for the project sponsor, Nina Aguayo, and her son, Jonathon Aguayo, in Fall of 2018. Jonathon is diagnosed with Delayed Brain Development and Hypotonia with some characteristics of Cerebral Palsy. He has a 50lb high intensity stroller to go to and from school. Mrs. Aguayo needed a stroller that is easier to transport while still meeting all of Jonathon’s needs. The re-designed stroller will make leisurely outings for Mrs. Aguayo and Jonathon …

Cavitation Number As A Function Of Disk Cavitator Radius: A Numerical Analysis Of Natural Supercavitation, Reid Prichard

Senior Honors Theses

Due to the greater viscosity and density of water compared to air, the maximum speed of underwater travel is severely limited compared to other methods of transportation. However, a technology called supercavitation – which uses a disk-shaped cavitator to envelop a vehicle in a bubble of steam – promises to greatly decrease skin friction drag. While a large cavitator enables the occurrence of supercavitation at low velocities, it adds substantial unnecessary drag at higher speeds. Based on CFD results, a relationship between cavitator diameter and cavitation number is developed, and it is substituted into an existing equation relating drag coefficient …

Restore-L Satellite Servicing Internship Final Report, Giovanni Campos

Publications and Research

This paper reviews the Restore-L mission purpose and the necessary research and simulations to meet mission specification for the Propellant Transfer Subsystem (PTS). It is essential the PTS undergoes functionality testing, environmental testing, and calculations to understand the capabilities of the system. For the testing of components from PTS, a proper test setup is required. It is vital for test hardware, such as hoses and valves, to stay in place while the test is being performed. For the test hardware to operate correctly, positioning, orientation, and alignment are critical as well. In addition to the testing, calculations for pressure drop …

Cpu Cooling Pulse Device For Enhanced Heat Transfer, Hannah Farabee, Noémie L. Iñiguez, Hugo Nunez, Wendy Zwanka

Senior Theses

Ice Dragon Cooling is a company which researches thermofluids and heat transfer technologies. The company’s present research focuses on HVAC and computer applications, with an emphasis on nanofluid development. To support Ice Dragon’s mission, the company wants a product that enhances heat transfer efficiency in liquid-cooled CPU systems. The product is to be a pulse device which increases the turbulence of a liquid across a computer CPU cooling block, thereby expediting heat transfer away from the CPU.

The needs for Ice Dragon Cooling were determined based on engineering knowledge and industry consultation. After further analysis, it was determined that increasing …

Developing And Testing Of An Upper Limb Exoskeleton For Stroke Patients, Drew Dudley, David Salazar

UNO Student Research and Creative Activity Fair

Objective: The main objective of this study was to determine functional and neuromuscular outcomes of stroke patients using their non-preferred hand with and without a 3D printed passive exoskeleton compared to controls using their non-preferred hand with and without the passive exoskeleton. Methods: Adults at least six months post stroke (Stroke, n = 5) and age- and sex- matched healthy controls (Control, n = 5) performed nine trials of a gross motor task while having their brain activity measured. The Fugl-Meyer and “Box and Block” test was used to measure the gross dexterity of the subjects with and without the …

Torsional Stiffness Of A Race Car, Reiley A. Schraeger, Cameron Kao, Raymond Deng, Omar Roman

Mechanical Engineering

Torsional stiffness plays a major role in any road vehicle. To understand torsional stiffness of a vehicle and make future iterations and improvements, a proper torsional stiffness jig is required to prove accurate and useful data. This report encompasses the new and improved testing jig and potential improvement ideas for more accurate results. With real data result relating to FEA calculations, designers can be confident in the FEA changes to torsional stiffness is accurate and will yield the probably results they desired. This report shows the methodology, manufacturing process and testing procedure to use on any Baja or SAE vehicle …

Composite Recycler: Frame, Alfonso Olivera

All Undergraduate Projects

How can composites be recycled? The Composite Recycler is an ongoing project that started in September 2017. The purpose of this project was to create a machine that will delaminate the composites, cut them, and heat them up to separate the resin from the composites so they can be recycled. A group was put together for the 2018-2019 academic year to further the project as a whole improve the operation of the device. The existing base was used as well as the cutter and the power sources. The upgrades included; a housing to support the transport rollers and changing from …

Stair Climbing Hand Truck, James Mcpherson

All Undergraduate Projects

Abstract

Getting a heavy object up a flight of stairs usually requires a team of two or more people. Even with a team of people, the task is often still difficult, dangerous, and possibly insurmountable by one person. This problem is especially prevalent in for those who are moving into apartment complexes. Most apartment complexes have many buildings with two or more floors of living quarters, and elevators are often missing. This project sought to offer a solution to this problem. The solution in question; a motorized hand-truck with 2, trigonal planar pinwheels in place of the stock wheels. The …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Custom Foot Prosthetic: Diabetic Care, Chandler Streuli

All Undergraduate Projects

Across the United States there are people every day who lose their toes to diabetes or to loss of circulation within their legs. The problem becomes building a more cost effective and efficient prosthetic for these individuals. The prosthetics that are used for medical purposes are often costly, especially without the help of insurance. The new prosthetic was designed to be taken in and out of shoes so that it is fast and easy for the user to move the device from shoe to shoe. The manufacturing method for this project was using a 3D printer to build the initial …

Electrathon: Body, Ryan Shiner

All Undergraduate Projects

• The Electrathon Vehicle project is an ongoing project that dates back to 2012. This vehicle will be raced at events to see how many laps it can complete on a single battery charge. The existing body for the Central Washington University Electrathon vehicle required modifications to fit over the current frame. These modifications were required because the rear suspension design had changed. The rear panel of the body interfered with the rear suspension. Using a rotary cutting wheel, the panel was slotted so the body could slide over the suspension and drive chain. Additionally, spacers for various sizes were needed …

Flow Fields Past Grain Bins As It Relates To Vertical Axis Wind Turbine Placement Optimization, Jon Richter

All Graduate Theses, Dissertations, and Other Capstone Projects

This thesis studies the 3D flow field of grain bins as it relates to Vertical Axis Wind Turbine (VAWT) placement. Numerical CFD simulations using ANSYS FLUENT were created and validated with the Minnesota State University, Mankato water channel. It was found that the best speed-up regions were on the outer most sides of the models, closest to the walls of the water channel. The model that is furthest upwind in the group has the best speed-up velocity. As the models become closer together, an asymmetric flow field develops. VAWT placement between the models for any case researched is not recommended. …

Dust Transportation And Settling Within The Mine Ventilation Network, Anand Kumar

Theses and Dissertations--Mining Engineering

Dust is ubiquitous in underground mine activities. Continuous inhalation of dust could lead to irreversible occupational diseases. Dust particles of size lower than 75.0 µm, also known as float coal dust, can trigger a coal dust explosion following a methane ignition. Ventilation air carries the float coal dust from the point of production to some distance before it’s deposited on the surfaces of underground coal mine. Sources of dust are widely studied, but study of dust transportation has been mainly based on experimental data and simplified models. An understanding of dust transportation in the mine airways is instrumental in …

Quantification Of Papillary Muscle Motion And Mitral Regurgitation After Myocardial Infarction, Connor R. Ferguson

Theses and Dissertations--Mechanical and Aerospace Engineering

Change in papillary muscle motion as a result of left ventricular (LV) remodeling after posterolateral myocardial infarction is thought to contribute to ischemic mitral regurgitation. A finite element (FE) model of the LV was created from magnetic resonance images acquired immediately before myocardial infarction and 8 weeks later in a cohort of 12 sheep. Severity of mitral regurgitation was rated by two-dimensional echocardiography and regurgitant volume was estimated using MRI. Of the cohort, 6 animals (DC) received hydrogel injection therapy shown to limit ventricular remodeling after myocardial infarction while the control group (MI) received a similar pattern of saline injections. …

A Computational Study Of Patch Implantation And Mitral Valve Mechanics, Dara Singh

Theses and Dissertations--Mechanical and Aerospace Engineering

Myocardial infarction (i.e., a heart attack) is the most common heart disease in the United States. Mitral valve regurgitation, or the backflow of blood into the atrium from the left ventricle, is one of the complications associated with myocardial infarction. In this dissertation, a validated model of a sheep heart that has suffered myocardial infarction has been employed to study mitral valve regurgitation. The model was rebuilt with the knowledge of geometrical changes captured with MRI technique and is assigned with anisotropic, inhomogeneous, nearly incompressible and highly non-linear material properties. Patch augmentation was performed on its anterior leaflet, using a …

Design And Process Of 3d-Printed Parts Using Composite Theory, Jordan Garcia

Theses and Dissertations--Mechanical and Aerospace Engineering

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it is observed that the procedures used in 3D printing differ substantially among the printers and from those used in conventional manufacturing. In this thesis, the mechanical properties of engineering products fabricated by 3D printing were comprehensively evaluated and then compared with those made by conventional manufacturing. Three open-source 3D printers, i.e., the Flash Forge Dreamer, the Tevo Tornado, and the Prusa, were used to fabricate the …

3d Printing In Low Resource Healthcare Settings: Analysis Of Potential Implementations, Alenna Beroza

Dissertations, Master's Theses and Master's Reports

3D printing has gained significant momentum in the past ten years, and its unique advantages make it especially ideal for use in low resource healthcare settings, where many designs have already been successfully implemented. Yet, little has been studied on how 3D printing can be sustainably and functionally implemented in low resource healthcare systems as a manufacturing practice. In this report, three business models are proposed for this implementation: In-House Operator, Independent Operator, and Print Farm. These models were then tested over four months in Kisumu county, Kenya, at two workshops and seven public hospitals. I worked with local medical …

Crack Pattern Simulation Of Pressurized Borosilicate Glass Tube Under Pellet Impact Using Ale Method, Omkar Bhumkar

Dissertations, Master's Theses and Master's Reports

Transformer bushings are a common target for sniper attacks to cause power failure in large areas. Given the size, internal pressure and brittle nature of transformer bushing, pellet impact causes damage to surrounding components due to broken bushing pieces. To mitigate this, a project was initiated by United States Burau of Reclaimation to develop a safety mechanism. Finite Element Analysis is proposed to optimize and reduce cost of the design.

A simplified Finite Element model is created which consists of 0.22 caliber lead pellet impacting Pyrex 7740 borosilicate glass tube. Previous studies on the effect of the mesh pattern, size …

Experimental And Numerical Simulation Of Split Hopkinson Pressure Bar Test On Borosilicate Glass, Mayank K. Bagaria

Dissertations, Master's Theses and Master's Reports

This study is an extension to the design of ceramic materials component exposed to bullet impact. Owing to the brittle nature of ceramics upon bullet impact, shattered pieces behave as pellets flying with different velocities and directions, damaging surrounding components. Testing to study the behavior of ceramics under ballistic impact can be cumbersome and expensive. Modeling the set-up through Finite Element Analysis (FEA) makes it economical and easy to optimize. However, appropriately incorporating the material in modeling makes laboratory testing essential. Previous efforts have concentrated on simulating crack pattern developed during 0.22 caliber pellet impact on Borosilicate glass. A major …

Space Dynamics Laboratory Payload Challenge: Autonomous Water Sampling Uav, Thomas Wheeler, Zachary Williams, Joseph Stack

Williams Honors College, Honors Research Projects

The following report has been completed over the course of the Fall 2018 and Spring 2019 semesters at The University of Akron by Joseph P. Stack (Aerospace Systems Engineering), Thomas J. Wheeler (Mechanical Engineering) and Zachary M. Williams (Mechanical Engineering). The purpose of this project was to create a payload system for the Akronauts Rocket Design Team to use at the Intercollegiate Rocket Engineering Competition (IREC) Spaceport America Cup. The Competition as a challenge that is sponsored by Space Dynamics Laboratory specifically regarding payload systems. The challenge in very open-ended and allows student to identify their own scientific experiment and …