Electrical and Electronics Commons^™

Transmission Electron Microscopy Characterization Of High-Temperatur Oxidation Of Fe-20cr-5al Alloy Prepared By Focused Ion Beam Technique, Mohammad Dani, Pudji Untoro, Teguh Yulius Surya Panca Putra, Parikin Parikin, Joachim Mayer, Arbi Dimyati

Makara Journal of Technology

The Focused Ion Beam (FIB) technique was applied for cross section preparation of the oxidized alloy for Transmission Electron Microscopy (TEM) study. Prior to preparation, the specimens of Fe-20Cr-5Al alloy sheet were oxidized in air at 1200 oC for 2 minutes, 10 minutes, 2 hours, and 100 hours. The microstructure and elemental composition of the samples were characterized using TEM equipped with an Energy Dispersive X-Ray Spectroscopy (EDX). The Electron Energy Loss Spectroscopy (EELS) was used to determine of the light elements. The TEM investigation reveals remarkable microstructure evolution of the specimens during oxidation which generally exhibit a typical multi-layer …

Creation Of Carbon Nanotube Based Biosensors Through Dielectrophoretic Assembly, Nilan S. Mani, Steve Kim, Kaushik Annam, Danielle Bane, Guru Subramanyam

Electrical and Computer Engineering Faculty Publications

Due to their excellent electrical, optical, and mechanical properties, nanosized single wall carbon nanotubes (SWNTs) have attracted significant attention as a transducing element in nano-bio sensor research. Controlled assembly, device fabrication, and bio-functionalization of the SWNTs are crucial in creating the sensors. In this study, working biosensor platforms were created using dielectrophoretic assembly of single wall carbon nanotubes (SWNTs) as a bridge between two gold electrodes. SWNTs in a commercial SDS surfactant solution were dispensed in the gap between the two gold electrodes, followed by applying an ac voltage across the two electrodes. The dielectrophoresis aligns the CNTs and forms …

Automatic Registration Of Optical Aerial Imagery To A Lidar Point Cloud For Generation Of City Models, Bernard Olushola Abayowa, Alper Yilmaz, Russell C. Hardie

Electrical and Computer Engineering Faculty Publications

This paper presents a framework for automatic registration of both the optical and 3D structural information extracted from oblique aerial imagery to a Light Detection and Ranging (LiDAR) point cloud without prior knowledge of an initial alignment. The framework employs a coarse to fine strategy in the estimation of the registration parameters. First, a dense 3D point cloud and the associated relative camera parameters are extracted from the optical aerial imagery using a state-of-the-art 3D reconstruction algorithm. Next, a digital surface model (DSM) is generated from both the LiDAR and the optical imagery-derived point clouds. Coarse registration parameters are then …

Dna Based Electrolyte/Separator For Lithium Battery Application, Jitendra Kumar, Fahima Ouchen-Bouchendouka, Devin A. Smarra, Guru Subramanyam, James Grote

Electrical and Computer Engineering Faculty Publications

In this study, we demonstrated the use of DNA-CTMA (DC) in combination with PolyVinylidene Fluoride (PVDF) as a host matrix or separator for Lithium based electrolyte to form solid polymer/gel like electrolyte for potential application in Li-ion batteries.

The addition of DC provided a better thermal stability of the composite electrolyte as shown by the thermos-gravimetric analysis (TGA). The AC conductivity measurements suggest that the addition of DC to the gel electrolyte had no effect on the overall ionic conductivity of the composite. The obtained films are flexible with high mechanical stretch-ability as compared to the gel type electrolytes only.

Design Method For Wideband Circularly Polarized Slot Antennas, Adam Narbudowicz, Matthias John, Vit Sipal, Xiulong Bao, Max Ammann

Articles

A compact ultrawideband (UWB) circularly polarized (CP) slot antenna is proposed with a methodology for automated reoptimization for packaging with proprietary devices. The slot structure employs a dual-feed with an integrated compact UWB phase shifter. The design process involves an advanced optimization algorithm and demonstrates the use of spline curves for generation of CP signals. These allow easy optimization, while preserving phase coherency across a wideband. The prototyped antennahas a CP bandwidth of 54% (from 3.2 to 6.1 GHz).

Secure Transmission And Retrieval Of Images In Conjunction With Steganography Using Chaos In Nonlinear Acousto-Optic Feedback, Monish Ranjan Chatterjee, Fares S. Almehmadi

Electrical and Computer Engineering Faculty Publications

Digital images are encrypted onto a chaotic carrier in a Bragg cell under hybrid nonlinear feedback and secure data is embedded into the system via steganography. System robustness (with and without channel noise) is analyzed vis-a-vis information security.

Design And Characterization Of A Low Cost Mems Imu Cluster For Precision Navigation, Daniel R. Greenheck

Master's Theses (2009 -)

The fast paced development of micro-electromechanical systems (MEMS) technology in recent years has resulted in the availability of low cost gyroscopes and accelerometers in commercial markets. These sensors can be integrated into a single device known as an inertial measurement unit (IMU). An IMU is capable of tracking and navigating a vehicle for a short period of time in the absence of external position and attitude updates. The precision of the manufacturing techniques used to fabricate commercial MEMS sensors as well as their mechanical nature result in noise and errors that limit their performance. It has been mathematically shown that …

Object Tracking From Multiple Multi-Axis Platforms In Four Dimensions, Theodore A. Teates

Electrical & Computer Engineering Theses & Dissertations

Object handoff in free space requires a sound framework between at least two optical sensors and one object. Previous work developed an algorithm that can determine the ap­ propriate time to initiate handoff of object tracking responsibilities from one optical sensor with an object in view to another optical sensor with the same object in view. In order to maintain persistent tracking of objects in this work, gimbal movements of optical sensors are determined by calculations using the Lagrange method to determine the trackability measures between the moving object and the handoff cone for the appropriate optical sensor. The rotation …

On The Calculation And Measurement Of Mean Room Surface Exitance, James Duff, G. Antonutto, S. Torres

Articles

Cuttle has proposed mean room surface exitance as a metric for use within interior lighting design. Two reported barriers to its use are: a lack of available software to calculate the metric and the tedious and cumbersome nature of recording its values in the field using current equipment and methodologies. This paper presents a method for facilitating the calculation of mean room surface exitance using readily available freeware, namely Radiance, and also presents a methodology that utilises high dynamic range imaging as a pragmatic alternative for field measurement.

Common Mode Voltage Mitigation Strategies Using Pwm In Neutral-Point-Clamped Multilevel Inverters, Chad Alexander Somogyi

Master's Theses (2009 -)

Over the last several decades, there has been consistent growth in the research and development of multilevel voltage-source inverter-based adjustable speed motor drives (ASDs) as a result of low cost, high reliability power semiconductors. The three-level neutral-point-clamped (NPC) ASD is a popular multilevel inverter used in low and medium voltage applications because of its ability to produce lower levels of total harmonic distortion (THD) and withstand higher voltages while preserving the rated output power compared to two-level ASDs. As with other voltage-source inverters, three-level NPC ASDs produce common-mode voltage (CMV) that can cause motor shaft voltages, bearing currents, and excess …

Design Optimization Of A Linear Generator With Dual Halbach Array For Human Motion Energy Harvesting, Wenjia Zhao

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

A linear generator for human motion energy harvesting is designed and optimized in this study. The linear generator can be used to convert human motion energy to electrical energy to charge portable electronics, such as cellular phones, wireless internet devices, etc. The use of dual Halbach magnet arrays in the proposed generator provides a significant improvement in power density. Different dual Halbach arrays were studied, and a novel Halbach array with nonuniform magnet blocks is proposed to enhance the air-gap flux density in the linear generator for a given size and weight of permanent magnet material. Sensitivity analyses were performed …

Cooperative 3-D Map Generation Using Multiple Uavs, Andrew Erik Lawson

University Scholar Projects

This report aims to demonstrate the feasibility of building a global 3-D map from multiple UAV robots in a GPS-denied, indoor environment. Presented are the design of each robot and the reasoning behind choosing its hardware and software components, the process in which a single robot obtains a individual 3-D map entirely onboard, and lastly how the mapping concept is extended to multiple robotic agents to form a global 3-D map using a centralized server. In the latter section, this report focuses on two algorithms, Online Mapping and Map Fusion, developed to facilitate the cooperative approach. A limited selection …

Pilot-1: Autonomous Fixed-Wing Aircraft Control System, Chris Millsap, Nathan Garvey, Faisal Hayat

Interdisciplinary Design Senior Theses

In the past decade, the personal ownership of unmanned aerial vehicles has exploded in the US and around the world. The rapidly declining size and cost of integrated circuits, sensors and embedded micro-controllers has lead to a flourishing community of hobbyists designing flight controllers with levels of sophistication approaching those for government and military applications. The typical flight assisted controllers integrate data from the user's control system and an Inertial Measurement Unit (IMU) in order to keep the craft level and on course. Deriving mostly from the radio controlled (RC) hobby industry, the flight control technologies for both rotary and …

A Transfer Function Based Frequency Model For Propagation Of A Chaos Wave Through Modified Von Karman Turbulence Under Various Chaos And Turbulence Conditions, Monish Ranjan Chatterjee, Fathi H.A. Mohamed

Electrical and Computer Engineering Faculty Publications

Complex phasor fields for electromagnetic wave propagation through von Karman turbulence and acousto-optic RF chaos are derived en route to the effective transfer function between chaos and narrow turbulence. Results are tested for several turbulence and chaos conditions.

Emergence Of Negative Index In A Lossy Chiral Metamaterial Under First-Order Material Dispersion, Monish Ranjan Chatterjee, Tarig A. Algadey

Electrical and Computer Engineering Faculty Publications

For a lossless dispersive chiral material, negative index (NIM) occurred only by use of parametric analysis (and not via practical models) to first-order. These findings are re-visited for the lossy problem and the results are compared.

Enterprise Smart Outlet, David Faltmier, Matthew Mcgill, Luke Stencel

Electrical Engineering

The purpose of our senior project, Enterprise Smart Outlet, is to create an electrical outlet which will allow enterprise users to monitor and change their power consumption habits on a large scale. The initial goal of this project is to allow consumers to see their power consumption per outlet in real time, and then using that information conform their future habits to help them conserve electrical energy, and more importantly, money. Three requirements for our project to meet our initial goal are, the outlet will work in a standard electrical outlet and be completely compatible with current electrical standards, the …

Shark Alert: Early Warning System, Cory Peterson, Marc Rauschnot, Taylor Mcclain

Electrical Engineering

The Shark Alert Early Warning System is a device geared toward avid beach goers such as surfers, divers, and swimmers. The system is composed of an ultrasonic transmitter mounted on a shark’s dorsal fin and a receiver worn by the user around the ankle. The receiver alerts the user to the presence of a shark upon ultrasonic signal detection.

The receiver warns the user through both visual and tactile (vibration) alerts to ensure user notification. This circuit was built and tested in the EE labs and Recreation Center pools to determine transmission range. The receiver detects the transmitted signal up …

U-Larm Bike Lock Accessory, Craig Cary

Electrical Engineering

Over the past few years, anti-pollution organizations and activists have encouraged society to use eco-friendly transportation like ride-sharing and biking. According to the San Luis Obispo Police Department, however, bike owners report approximately 269 bike thefts per year. This statistic illustrates the need for a more effective way to protect bicycle property.

The development of an alarm system for the U-Lock bike lock encourages bike owners to ride their bicycles by providing them with additional measures to protect their bicycle property. This U-Lock accessory, when cut, sounds an alarm to alert nearby persons of the theft-in-progress. In order to turn …

Smart Shot: Electronic Target With Smartphone Application, Tyler Stuart Pickett, Taylor Jacob Hutchinson

Electrical Engineering

The objective of this project is to develop an electronic system for recreational shooters that functions as a target with real-time feedback. The system provides a user-friendly alternative to paper targets and expensive competition scoring systems. One of the largest challenges presented by this project is balancing cost, durability, and sensitivity. The scope of this project includes the design and implementation of a target assembly, an electronic system, and a smartphone application.

The system is comprised of three main modules: the target, the control module, and the smartphone app. The electronic target communicates wirelessly with the smartphone via Bluetooth. Once …

Rocket Cam: Low Frequency Analog Transmission Of Digital Video, Thomas J. Higdon

Electrical Engineering

The camera module provides data for improving models of dynamic events on Orbital ATK Corp. rockets and aids in troubleshooting, if necessary. Video images provide a valuable addition to the strain, vibration, shock, and acoustic data used for modeling dynamic events, such as stage separations. The cameras can record a duration of video data suitable for capturing a dynamic event and of high enough quality to aid in its modeling. The module readily integrates into the rocket’s current analog data collection systems. The project has further relevance to any other application that necessitates video data transmission over similar limited-bandwidth, analog …