Chemical Engineering Commons^™

Determination Of Optimal Parameters For Quality Drying Of Garlic Using The Vibro-Convective Method, Jasur Safarov, Shakhnoza Sultanova, Abdurakhmon Mirkomilov

Chemical Technology, Control and Management

This article examines the process of drying garlic using a low-temperature vibratory-convective drying system. At the "Service Technology" department of Tashkent State Technical University, a vibratory dryer was developed to ensure high-quality drying of garlic while maximizing the preservation of its biologically active compounds. Through experimental studies, optimal drying parameters were determined, including the degree of moisture removal, process duration, airflow velocity, and vibration acceleration. The results obtained contribute to enhancing the efficiency and quality of garlic drying, which holds practical significance for agricultural producers and consumers interested in healthy nutrition.

Development Of Fuzzy Ontology For Explainable Artificial Intelligence For Decision-Making In Fuzzy Environment, Pavel Kosov

Chemical Technology, Control and Management

In modern artificial intelligence systems, there is an acute need to understand the decision-making logic of "black box" algorithms. Our research proposes an innovative method for increasing the transparency of such systems through the formalization of fuzzy explanatory mechanisms. We have developed an extension of existing ontological approaches by introducing the concept of fuzziness into the structure of explanatory properties, which allows overcoming the fundamental limitations of traditional XAI methods. The proposed formalization is based on the theory of collective mental models and principles of fuzzy logic, providing a more accurate reflection of uncertainty and subjectivity in expert knowledge. Our …

Dust Analyses In Ventilation Ducts, Karolina Vyhlidalova, Petr Vlček, Olga Rubinová, Jiří Bernard

Journal of Sustainable Construction Materials and Technologies

The paper describes the importance of monitoring the dust in the atmosphere of human life. It deals with the issue of dust in air ducts, approaching the methods that can be used to detect the amount of dust. For conditions for buildings in the Czech Republic there is created the methodology of quantitative and qualitative evaluation of dust sediment for the needs of HVAC and other building surfaces. The scale for visual evaluation was created and it has been elaborated the assessment of kind of particles contained in dust.

Assessment Of Long Time Approximation Equation To Determine Thermal Conductivity Of High Porous Materials With Nss Probe, Hussein Humaish, Bastien Ruet, Laurent Marmoret, Hassen Beji

Journal of Sustainable Construction Materials and Technologies

Recent economic changes have increased the focus on energy conservation in buildings. Improve insulation represents one of the biggest challenge to save energy. The TP02 Huksefux® Non Steady State Probe (NSSP) has been used to determine the thermal conductivity of the building insulation materials. Usually, the long term approximation equation (linear form) is applied to determine the thermal conductivity when using hot wire techniques. Long term approximation has been successfully used to characterize glycerol: a fluid which doesn’t present contact resistance and porosity. But, an S-shaped appears for more porous materials. So to generalize the possibility of using this method, …

Integrating Environmental Analyses And Awareness To The Senior Chemical Plant Design Course Che 4233, Lucie I. Leblanc

Honors Theses

The EPA has implemented and increased environmental regulations and safeguards for carbon dioxide (CO2) and volatile organic compound (VOC) emissions for the past 70 years. These regulations have affected the technology and methodology used in industrial chemical production processes. As newly graduated engineers enter the work field, they will encounter current and future EPA regulations, and they will have to adjust their production units to meet these safeguards. This report loosely follows the structure of the Plant Design Course (CHE 4233) to show the process of designing a conventional cumene production plant. The conventional process is compared to a new …

Electrocatalytic Nitric Oxide Reduction To Yield Ammonia Over Fe3C Nanocrystals, Sen Lin, Lang Zhang, Tong Hou, Jun-Yang Ding, Zi-Mo Peng, Yi-Fan Liu, Xi-Jun Liu

Journal of Electrochemistry

Nitric oxide (NO), which generally originates from vehicle exhaust and industrial flue gases, is one of the most serious air pollutants. In this case, the electrochemical NO reduction reaction (NORR) not only removes the atmospheric pollutant NO but also produces valuable NH₃. Hence, through the synthesis and modification of Fe₃C nanocrystal catalysts, the as-obtained optimal sample of Fe₃C/C-900 was adopted as NORR catalyst at ambient conditions. As a result, the Fe₃C/C-900 catalyst showed an NH₃ Faraday efficiency of 76.5% and an NH₃ yield rate of 177.5 μmol·h^–1·cm^{–2 …}

Ordering Degree Regulation Of Pt2Nico Intermetallics For Efficient Oxygen Reduction Reaction, Chen-Hao Zhang, Han-Yu Hua, Jun-Hao Yang, Qian Zhang, Chang Yang, De-Li Wang

Journal of Electrochemistry

Alloying transition metals with Pt is an effective strategy for optimizing Pt-based catalysts toward the oxygen reduction reaction (ORR). Atomic ordered intermetallic compounds (IMC) provide unique electronic and geometrical effects as well as stronger intermetallic interactions due to the ordered arrangement of metal atoms, thus exhibiting superior electrocatalytic activity and durability. However, quantitatively analyzing the ordering degree of IMC and exploring the correlation between the ordering degree and ORR activity remains extremely challenging. Herein, a series of ternary Pt₂NiCo intermetallic catalysts (o-Pt₂NiCo) with different ordering degree were synthesized by annealing temperature modulation. Among them, the o-Pt …

Performance Of Co2/H2O Co-Electrolysis In A Flat-Tube Solid Oxide Electrolysis Cell Stack Under Air-Free Environment, Xiao-Hui Zhong, Fei Wang, An-Qi Wu, Bei-Bei Han, Jian-Xin Wang, Wan-Bing Guan

Journal of Electrochemistry

This work investigates the transient performance and stability of CO₂/H₂O co-electrolysis in an air-free environment using a flat-tube solid oxide electrolysis cell (SOEC) stack. The results show that the transient behavior of the stack with and without blowing gas in the air electrode is almost the same. With a current density of 0.67 A·cm⁻²@750 °C, the stack operated for over 200 h under co-electrolysis conditions with no air blowing, and the voltage drop rate of the stack was approximately 0.203%/100 hours. Microstructure analysis reveals significant loss of Ni particles and formation of an insulating …

Variation Of Membrane Electrode Assembly Catalyst Layer In Unitized Regenerative Fuel Cell, Yollanda Nurcholifah, Dedi Rohendi, Edy Herianto Majlan, Nirwan Syarif, Addy Rachmat, Dwi Hawa Yulianti, Nyimas Febrika S

Journal of Electrochemistry

A unitized regenerative fuel cell (URFC) is a device that may function reversibly as either a fuel cell (FC) or water electrolysis (WE). An important component of this device is the Membrane electrode assembly (MEA). Therefore, this study aimed to compare the performance outcomes of MEA using electrodes with single and three catalyst layers. This study measured Electrochemical Surface Area (ECSA), Electrochemical Impedance Spectroscopy (EIS), X-ray Diffraction analysis (XRD), and X-ray Fluorescence (XRF). Furthermore, the round-trip efficiency (RTE) of the MEA, as well as the performance in FC and WE mode, was measured. In comparison, The ECSA values of Pt-Ru/C …

Small-Scale Production Of Bespoke Accelerated Aging Plutonium Alloy, K. S. Holliday, A. M. Parkes, Devin Rappleye, D. J. Roberts, K. J. Kondrat, S. A. Simpson, A. J. Swift, U. Mehta, R. M. Kissinger, D. L. Rosas, L. S. Ripplinger, E. R. Tardiff, S. L. Harris, S. Perkins, C. Hawkins, N. J. Gibbs, R. J. P. Driscoll, A. T. Sidambe, R. A. Cole, T. T. Roehling, J R. Jeffries

Faculty Publications

This study demonstrates the 100 g scale manufacture of a plutonium alloy that ages at an accelerated rate. The resulting alloy ages six times faster than typical weapons-grade plutonium due to the addition of ²³⁸Pu. As a major innovation, the process involved using a partial direct oxide reduction technique. This method was achieved by developing a new, complex geometry stirrer using additive manufacturing to reduce the ²³⁸Pu oxide and efficiently incorporate it into weapons-grade plutonium metal. The material was then purified by molten salt extraction and electrorefining before being alloyed with gallium. The alloy was then cold-rolled and …

Methods For Rotating Electrodes In High-Temperature Molten Salts, Ranon Fuller, Eloise Cluff, Edward Mercado, Carlos Mejia, Devin Rappleye

Faculty Publications

In this paper, we describe and validate a custom apparatus for performing high-speed (250-3,500 rpm) rotating electrode and dilatometer density experiments in molten salts. The reported details can aid in decreasing the difficulty and increasing the quality of such experiments. We discuss the design challenges and the solutions identified. We investigate methods for accurately measuring the solution resistance using electrochemical impedance spectroscopy (EIS), calculating the working electrode area using cyclic voltammetry (CV), and measuring the mass transfer-limited current of rotating electrodes using a series of chronoamperometry (CA) pulses. We further demonstrate the efficacy of our methods in producing accurate results.

Porous Hierarchically Ordered Hydrogels Demonstrating Structurally Dependent Mechanical Properties, Elisabeth C. Lloyd, Sujata Dhakal, Shahrouz Amini, Rami Alhasan, Peter Fratzl, Douglas R. Tree, Svetlana Morozova, Robert J. Hickey

Faculty Publications

While hierarchical ordering is a distinctive feature of natural tissues and is directly responsible for their diverse and unique properties, efforts to synthesize biomaterials have primarily focused on using molecular-based approaches with little emphasis on multiscale structure. Here, we report a bottom-up self-assembly process to produce highly porous hydrogel fibers that resemble extracellular matrices both structurally and mechanically. Physically crosslinked nanostructured micelles form the walls of micrometer-sized water-rich pores with preferred orientation along the fiber direction. Low elastic moduli (< 1 kPa), high elasticity (extending by more than 12 times the initial length), non-linear elasticity (e.g., hyperelasticity), and completely reversible extension are derived from unevenly distributed strain between the micrometer-sized pores and the polymer chains, which is reminiscent of cellular solids. Control of the material microstructure and orientation over many orders of magnitude (e.g., nm–μm), while holding the nanostructure constant, reveals how the multiscale structure directly impacts mechanical properties.

Effect Of Precursors On Trimetallic Ruthenium-Based Catalysts Supported On Γ‑Al2O3 Pellets For Low-Temperature Ammonia Decomposition, Christopher J. Koch, Jennifer Naglic, Logan Kearney, Daniel Clairmonte, Binod Rai, Jochen A. Lauterbach, Lucas M. Angelette, Tyler Guin

Faculty Publications

Ammonia is a promising candidate as a liquid hydrogen energy storage medium, but it requires catalytic decomposition (ammonia cracking) to regenerate hydrogen. Recently developed trimetallic ruthenium−potassium-promoter (RuKM) ammonia decomposition catalysts have exceptionally low ammonia decomposition temperatures, able to perform the decomposition as low as 250 °C, which is significantly lower than other known catalysts that require temperatures above 500 °C. However, the effects of the RuKM precursor on the catalytic activity have not been investigated. We report the observed differences of 3% ruthenium/12% potassium/1% yttrium (RuKY) catalysts on γ-alumina synthesized from chloride-, nitrate-, and acetate-based precursors. Catalysts synthesized from chloride-based …

Selective Lithium Extraction Using Ion-Sieves From Geothermal Brine, Agyare Asante, Abigail Berardi, Jayla Standin, Elliott Walker, Ujjwal Pokharel, Sandeep Kumar

Graduate Student Government Association Research Conference

Lithium (Li) is a critical component in modern green energy technologies, serving as the cornerstone for advanced batteries used in electric vehicles, renewable energy storage, and portable electronics. To address the increasing global demand for lithium, this study explores the synthesis and performance of ion-sieve novel adsorbents derived from the spinel-type precursor Li₄Mn_4.5Zr_0.5O₁₂ (LMZO). The precursor was produced using an economical solid-phase reaction that involved lithium, manganese, magnesium, and zirconium salts. This was followed by a two-stage calcination process involving 200 K for 2 hours and 450 K for 24 hours. Acid activation …

Evaluating The Potential For Reusing Process Waste Fiber, Elisha Ewing

Honors Theses

This study was born out of curiosity around the potential use of reject materials from the papermaking screening system for molded fiber product development. The team sought to explore the technical feasibility of this concept and develop a proposed design for mill implementation. The project supports the common papermaking objective of reducing fiber loss from the stock preparation process.

The project assessed first the technical feasibility through laboratory testing and trials. The team dedicated time to characterizing screen reject samples from local mills and running trials using the good fibers extracted from the samples. Molded fiber products were successfully created …

Analysis Of Pistachio Shell-Derived Activated Porous Carbon Materials For Hydrogen Adsorption, Setareh Elyasi, Nishar Hameed, Peter J. Mahon, Saulius Juodkazis, Alireza Keshavarz, Stefan Iglauer, Tawanda Matamba, J. Vongsvivut, Nisa V. Salim

Research outputs 2022 to 2026

Developing efficient storage materials is critical for advancing the hydrogen economy. In this study, we aim to utilize plant-based biomass as a sustainable source for fabricating porous carbon (PC) and subsequently employing it for hydrogen adsorption. For the first time, we synthesize highly porous carbon materials from pistachio shells as precursor materials for efficient hydrogen storage. Experiments were conducted to chemically activate pistachio shells using two different agents, sodium chloride (NaCl) and potassium chloride (KCl), at varying ratios. This study evaluates the effectiveness of these chemical activation agents in enhancing the surface area of PC and, consequently, its hydrogen adsorption …

Continuous Purification Of A Parvovirus Using Two Aqueous Two-Phase Extraction Steps, Natalie Nold, Sheridan Waldack, Grace James, Trisha Colling, Lynn M. Manchester, Taravat Sarvari, Amanda P. Bekkala, Seth Kriz, Madison Baldwin, Emily Agustin-Mazariegos, Michael J. Betenbaugh, Caryn Heldt

Michigan Tech Publications

Aqueous two-phase systems (ATPS) are a liquid–liquid extraction method that offers low-cost, continuous-adaptable virus purification. A two-step ATPS using polyethylene glycol (PEG) and sodium citrate that recovered 66% of infectious porcine parvovirus with 2.0 logs of protein removal and 1.0 logs of DNA removal in batch has now been run continuously. The continuous system output of < 10 ng/mL DNA regardless of starting DNA titer agreed with batch studies. However, the continuous system had a five-fold higher contaminating protein titer than batch studies, likely because of incomplete mixing or settling. Turbidity was tested as a measure of mixing and settling efficiency. Monitoring in-line absorbance at 880 nm directly after mixing and before collection in the settling reservoir could track both mixing and settling during operation. Settling time was reduced by changing the settling line material from PVC to PTFE, which is more hydrophobic. A flow-through AEX filter tested to make impurity removal more robust recovered 90% of PPV and removed an additional 87% of host cell DNA. The filter did not add any additional protein removal. In the future, in-line absorbance sensors could be implemented along with conductivity sensors to measure salt concentration, refractive index sensors to track the PEG-citrate interface, and scales to track mixer and reservoir volumes to enable automated, continuous ATPS. Our vision is to integrate continuous ATPS into a fully continuous end-to-end production for viral vectors.

Modular Molecular Design Of Polymerized Pro-Estrogen Materials Enables Controlled Astrocyte Response, Devan L. Puhl, Alexis Ziemba, Samuel A.T. Ellman, Alex Hsu, Jayant Saksena, Penelope Phillips Falcone, Bailey Balouch, Deniz Rende, Tanner Fink, R. Helen Zha, Ryan J. Gilbert, Edmund F. Palermo

Chemical and Biochemical Engineering Faculty Research & Creative Works

The hormone 17β-estradiol (estrogen or "E2") has demonstrated robust neuroprotective properties in countering oxidative stress-induced neurotoxicity, as well as strong neurotrophic properties to promote axonal growth, following injury to the central nervous system (CNS). However, oral or injected E2 is a suboptimal drug, as systemic administration fails to achieve a therapeutic dose at the injury site, in addition to being contraindicated in most male patients. Polymerized pro-drug biomaterials can mitigate these issues by locally releasing small quantities of drug over vastly extended timescales. We sought to study the effect of the biomaterial properties of poly(pro-E2) on astrocyte-surface interactions because astrocytes …

Nanostructured Transition Metal Oxides For Electrochemical Co2 And Methane Conversion, Olumide O. Oladoyin

Chemical and Biological Engineering ETDs

Rising atmospheric CO₂ and CH₄ drive climate change, prompting research into their electrochemical conversion to valuable products. This study investigates electrodeposited nanostructured transition metal oxides (TMOs), unary (CuO, Co₃O₄) and dual (Cu-Co oxide) as catalysts for CO₂ reduction and CH₄ oxidation under ambient conditions. Fabricated on various substrates (Cu foil, SS316, carbon paper) and characterized by SEM, their electrochemical performance was evaluated via cyclic voltammetry.

Cu-Co oxide showed superior CO₂ reduction, leveraging the strengths of individual oxides. Co₃O₄ exhibited higher current densities for CH₄ oxidation, with SS316 proving the best substrate. Catalyst composition, morphology, and substrate significantly influenced efficiency. While …

Biowaste Valorization: Integrating Circular Economy Principles With Artificial Intelligence-Driven Optimization For Sustainable Energy Solutions, Dina Aboelela Dr.

Biochemical Engineering

Biowaste, encompassing food waste and agricultural residues, poses significant environmental challenges while offering transformative opportunities. Traditionally relegated to landfills or incineration, biowaste is increasingly recognized as a renewable resource for producing biofuels, biochemicals, biomaterials, and animal feed. This review offers a systems-level analysis of biowaste characteristics, conversion processes, and derived bioenergy products such as biofuels, biogas, biodiesel, biohydrogen, bioelectricity, and other valuable chemicals. Diverse conversion methods are explored, including anaerobic digestion, fermentation, microbial fuel cells, pyrolysis, and gasification, alongside conventional practices like landfilling and incineration. Emerging analytical advancements are revolutionizing biowaste valorization. Artificial intelligence (AI) …