Catalysis and Reaction Engineering Commons^™

Rambling Between "Zhong Yong" And "Catalysis", Zi-Dong Wei

Journal of Electrochemistry

“Zhong Yong” represents a traditional Chinese wisdom, which was first proposed by Confucius and continuously richened by his followers. “Zhong Yong” pursues the balances among all kinds of contradictions, and insists that neither “too much” nor “not enough” is good. For a successful catalyst, on which the adsorption of reactants must be not so strong and not so weak either. On this point of view, there are the same pursuits for “Zhong Yong” and catalysis. In this paper, the author starts his story with a conversation between Confucius and his student, followed by 3 interesting stories happening in the ancient …

Preparation And Performance Of 3d Graphene Type Porous Carbon Employing Nano Fe(Oh)3 As Template For Oxygen Reduction Catalyst, Chong-Yun Sun, Zhong-Fang Li, Xue-Wei Lu, Xi-Zhan Zhong, Yu-Rong Liu

Journal of Electrochemistry

The 3D graphene type porous carbon was prepared using coal tar pitch as carbon source and nano Fe(OH)₃ as template. Optimal conditions for the catalytic oxygen reduction performance were determined as: the mass ratio of coal tar, nano Fe(OH)₃ and KOH is 6:8:4; the pyrolysis temperature is 800 ^oC. SEM images show that the products have uniformly porous structure. TEM images demonstrate that the products are porous with foam shapes. HRTEM images further indicate that the products have formed several-layers 3D graphene structure, which are also supported by XRD and Raman data, and the pore size mainly …

Synthesis Of Fe, N-Doped Graphene/Carbon Black Composite With High Catalytic Activity For Oxygen Reduction Reaction, Chi Chen, Zhi-You Zhou, Xin-Sheng Zhang, Shi-Gang Sun

Journal of Electrochemistry

Oxygen reduction reaction (ORR) is a bottleneck for improving the efficiency of proton-exchange membrane fuel cells as a cathode reaction due to its sluggish kinetics. The exploitation of low cost and high performance non-precious metal catalysts such as Fe/N/C based materials toward ORR has attracted extensive attentions. In this work, the Fe, N-doped graphene nanosheets/carbon black composite was prepared by hydrothermal polymerization and followed by a twice-heat-treatment procedure using 2-aminoimidazole as an N precursor, FeCl₃ as an Fe precursor and KJ600 carbon black as a support. The TEM images revealed that the graphene nanosheets were separated by carbon black …

Electricity Generation Of Microbial Fuel Cell Using Stainless Steel Mesh As Cathode, Hong-Yan Dai, Hui-Min Yang, Xian Liu, Xuan Jian, Xiu-Li Song, Zhen-Hai Liang

Journal of Electrochemistry

In the present work, a dual-chamber microbial fuel cell (MFC) was constructed with aeration tank sludge as an inoculum, carbon felt as an anode and stainless steel mesh without any modification as a cathode. The influence of the cathode size was investigated in terms of voltage output, power generation and electrochemical impedance. The long-term durability of the stainless steel mesh cathode was also evaluated. Results showed that the stainless steel mesh exhibited satisfactory long-term durability as MFC cathode. When the stainless steel mesh size was 2 × 2 cm², the maximum output voltage, power density, the internal resistance …

Electrochemical Detection Of Hydrogen Peroxide At Aunps Modified Electrode Using P-Hydroxyphenylboronic Acid As A Precursor, Chun-Yan Wang, Xiao-Qiu Liu, Ying-Xin Qi

Journal of Electrochemistry

We developed a new method for electrochemical detection of hydrogen peroxide (H₂O₂) based on boronate oxidation of p-hydroxyphenylboronic acid. This method using p-aminophenol which is produced from the reaction of H₂O₂ and p-aminophenylboronic acid as a well electrochemical probe, combined with a gold nanoparticles (AuNPs) modified electrode for an indirect detection of H₂O₂. Because of the large surface area and enhanced electrocatalytic behavior by the AuNPs modified electrode, the detection sensitivity was improved. The method could detect H₂O₂ in the concentration range of 1 ~ 100 …

The Study On Comparison Of Electrochemical Performance In Microbial Fuel Cell With Glucose And Sodium Acetate Acting As Substrates, Lei Fan, Yu Zhao, Ting Li, Qin-Bo Yuan, En-Zhi Wang, Xiao-Bin Wang, Jun-Wen Wang

Journal of Electrochemistry

By inoculating aerobic sludge and anaerobic sludge from the sewage treatment plant, two sets of dual-chamber microbial fuel cells (MFCs) were built with either glucose or sodium acetate acting as a substrate. Accordingly, the electrochemical performances of MFCs were explored with the concentration of the substrates being 0.0335 mol⋅L^-1. The results of the comparative study in glucose system and sodium acetate system showed that the impedance values of anodic half cell were 222 Ω for glucose and 213.67 Ω for sodium acetate, implying no significant effect on the internal resistance in battery with the different substrates. The exchange …

Electrochemical Syntheses Of Graphene And Its Composites, Bo Zhao, Li Jiang, Ming-Hui Yuen, Xian-Zhu Fu, Rong Sun, Ching-Ping Wong

Journal of Electrochemistry

Graphene is a kind of ideal two-dimensional flat carbon nanomaterials which have unique chemical and physical properties. The attractive potential applications must be based on the high quality mass production of graphene. However, it remains a huge challenge. An electrochemical approach is a fast, environmental friendly and easy-operating method. single- or multi-layered graphene flakes can easily be produced in short periods of time. In this review, the structure, properties and preparation methods of graphene are first introduced. Accordingly, the electrochemical approaches used for the productions of graphene flakes, graphene/inorganic nanocomposites, graphene/polymer composites and graphene analogues are highlighted. Finally, challenges and …

State-Of-The-Art Review Of Cathodic Protection For Reinforced Concrete Structures, Aimee Byrne, Niall Holmes, Brian Norton

Articles

Cathodic protection (CP) limits the corrosion of a metal surface by making it the cathode of an electrochemical cell. This can be achieved either by using a more active sacrificial anode to create a driving current, or by using inert anodes and impressing a current onto the cathode surface using an external direct current (DC) source. Impressed current cathodic protection (ICCP) is preferred where widespread protection is required, particularly in reinforced concrete structures. ICCP needs a constant DC power supply that is usually provided through a grid connection or independent generators. This paper presents the currently available CP systems for …

Cement Based Batteries And Their Potential For Use In Low Power Operations, Aimee Byrne, Niall Holmes, Brian Norton

Articles

This paper presents the development of an innovative cement-electrolyte battery for low power operations such as cathodic protection of reinforced concrete. A battery design was refined by altering different constituents and examining the open circuit voltage, resistor loaded current and lifespan. The final design consisted of a copper plate cathode, aluminium plate anode, and a cement electrolyte which included additives of carbon black, plasticiser, Alum salt and Epsom salt. A relationship between age, temperature and hydration of the cell and the current it produced was determined. It was found that sealing the battery using varnish increased the moisture retention and …

Selective, Catalytic Decomposition Of Hydrazine, Benjamin A. Kitson, Shirin N. Oliaee

Williams Honors College, Honors Research Projects

The selective, catalytic decomposition of hydrazine has been investigated using a 1 wt% Pt-Ni(OH)₂ catalyst system quantitatively studied by changing the following parameters; reaction solution alkalinity, temperature, hydrazine concentration, catalyst selectivity, catalyst stability, and catalyst durability. Using sodium hydroxide (NaOH), the best alkalinity was found to be 1 M NaOH. The optimal temperature was found to be 50 °C for complete hydrazine conversion. A hydrazine concentration of 0.1 M produced the most effective reaction. The catalyst was found to be completely selective in hydrogen and nitrogen production with no ammonia formation. The catalyst activity decreased by 15% after 8 …

Reaction Parameters And Energy Optimisation For Biodiesel Production Using A Supercritical Process, Nessren Farrag, Mamdouh Gadalla, Mai Fouad

Chemical Engineering

No abstract provided.

An Overview Of The Development Of Cement-Based Batteries For The Cathodic Protection Of Embedded Steel In Concrete, Aimee Byrne, Niall Holmes, Brian Norton

Conference papers

This paper presents an overview of the cement-based batteries developed in DIT for use in the cathodic protection of embedded steel in reinforced concrete undergoing chloride-induced corrosion. Cathodic protection delivers an external current (approximately 20mA per m2 of embedded steel) which effectively polarises the internal current generated during corrosion. The batteries developed in DIT comprise of a cement-based electrolyte containing different additives including sand, aggregate, salts, carbon black and plasticiser with protruding anode and cathode metal plates. These batteries produced an initial electrical output of 1.5V and 23mA through a 10 resistor as measured using data acquisition units and a …

Effect Of Ce And Co Addition To Fe/Al2o3 For Catalytic Methane Decomposition, Ahmed S. Al-Fatesh, Ashraf Amin, Ahmed A. Ibrahim, Wasim Ullah Khan, Moustafa A. Soliman, Raja L. Al-Otaibi, Anis H. Fakeeha

Chemical Engineering

Catalytic methane decomposition is studied in a fixed bed reactor. Two sets of bimetallic catalysts are employed, namely: 30%Fe-X%Ce/Al2O3 and 30%Fe-X%Co/Al2O3, and compared with monometallic 30%Fe/Al2O3 catalyst. The effect of promoting Fe with Ce and Co and reduction temperature are investigated. The results reveal that Ce addition has shown a negative impact on H2 yield while a positive effect on H2 yield and catalyst stability are observed with Co addition. In terms of number of moles of produced hydrogen per active sites, Fe/Al2O3 has shown a higher number of moles of hydrogen compared to bimetallic catalysts. The catalyst reduced at …

Synthesis Of Porous Carbon Nanosheets And Its Application In Sodium-Ion Battery, Jing-Fei Zhang, Jing Lu, Xiao-Yu Yang, Yun-Di Huang, Lin Xu, Dong-Mei Sun, Ya-Wen Tang

Journal of Electrochemistry

Owning to sodium’s high abundance, relatively low cost, similar chemical properties to Li and very suitable redox potential of E₀(Na⁺/Na) = -2.71 V versus SHE which is only 0.3 V above that of lithium, rechargeable sodium ion battery hold much promise as potential alternatives to current lithium ion batteries for energy storage applications. Carbon material is regarded as the most promising anode candidate for sodium ion battery. Particularly, carbon nanosheet with porous structure and high conductivity is expected to have improved sodium ion storage properties. In this paper, we present a two-step pyrolysis-based method for facile …

Methods For Coating Quartz Crystals, William Patrick

Senior Honors Projects, 2010-2019

The goal of this project was to evaluate the effectiveness a procedure that can be used to coat quartz crystal microbalance crystals with titanium dioxide. A successful suspension was created by suspending titanium dioxide powder in poly(acrlic) acid and mixed in an ultra-sonication bath. By utilizing a spin-coater, the TiO₂ suspension was successfully dispensed onto a QCM crystal and verified using a surface profiler and microscope. However, after QCM testing, there was no evidence that supports the TiO₂ precursor aiding in photocatalytic reactions.

Applying Bayesian Machine Learning Methods To Theoretical Surface Science, Shane Carr

McKelvey School of Engineering Graduate Student Theses & Dissertations

Machine learning is a rapidly evolving field in computer science with increasingly many applications to other domains. In this thesis, I present a Bayesian machine learning approach to solving a problem in theoretical surface science: calculating the preferred active site on a catalyst surface for a given adsorbate molecule. I formulate the problem as a low-dimensional objective function. I show how the objective function can be approximated into a certain confidence interval using just one iteration of the self-consistent field (SCF) loop in density functional theory (DFT). I then use Bayesian optimization to perform a global search for the solution. …

Size-Controlled Large-Diameter And Few-Walled Carbon Nanotube Catalysts For Oxygen Reduction, Xianliang Wang, Qing Li, Hengyu Pan, Ye Lin, Yujie Ke, Haiyang Sheng, Mark T. Swihart, Gang Wu

Faculty Publications

We demonstrate a new strategy for tuning the size of large-diameter and few-walled nitrogen-doped carbon nanotubes (N-CNTs) from 50 to 150 nm by varying the transition metal (TM = Fe, Co, Ni or Mn) used to catalyze graphitization of dicyandiamide. Fe yielded the largest tubes, followed by Co and Ni, while Mn produced a clot-like carbon morphology. We show that morphology is correlated with electrocatalytic activity for the oxygen reduction reaction (ORR). A clear trend of Fe > Co > Ni > Mn for the ORR catalytic activity was observed, in both alkaline media and more demanding acidic media. The Fe-derived N-CNTs exhibited …

Preparations And Properties Of Polybenzimidazole/Polyvinylbenzyl Crosslinked Composite Membranes For High Temperature Proton Exchange Membrane Fuel Cells, Jin-Kai Hao, Yong-Yi Jiang, Zhen Wang, Xiao-Jin Li, Zhi-Gang Shao, Bao-Lian Yi

Journal of Electrochemistry

In order to increase the chemical stability of polybenzimidazole (PBl) membrane, a highly stable polymer, poly vinyl. benzyl chloride (PVBC), was chosen as the macromolecular crosslinker, and 1H-1,2,4-triazol was adopted to prepare the crosslinked PBI-based membranes. The influence of the PVBC amount on membrane characteristic was investigated in detail. The results indi. cated that the crosslinked structure of the membrane effectively improved the chemical stability, and at the same time, the mem. brane presented good mechanical property and proton conductivity. The fuel cell performance for the membrane was tested with hy. drogen and oxygen single cell without humidification at 150 …

Synthesis, Characterisation, Electrochemical, And Spectroscopic Studies Of Cobaloximes: Unique Clues Of Cobalt(I) Species In Various Solvents, Michael John Celestine

Chemistry & Biochemistry Theses & Dissertations

With the dwindling amount of fossil fuels in the world’s reserve is said to run out in the future. The use of alternative fuels such as hydrogen can be produced from renewable sources. One source is the use of first row transition metal complexes that can harness the power of the sun to reduce protons to hydrogen. In this thesis we investigated a well-known hydrogen evolution catalyst in a quest to understand the behavior of different oxidation states that occur during the catalytic cycle.

In an attempt to synthesize a binuclear ruthenium(II) complex, [{Ru(phen)2}2{µmes(1,4-phO-Izphen)3}](PF6)4, as a possible photosensitizer for the …

Characterization Of Iron Phthalocyanine As The Cathode Active Material For Lithium-Ion Batteries, Sarwan S. Sandhu, Joseph P. Fellner

Chemical and Materials Engineering Faculty Publications

The developed thermodynamic functions for the determination of Gibbs free energy, enthalpy, and entropy of formation of solid lithium-iron phthalocyanine (LixFePc) from solid lithium and iron phthalocyanine as a function of x, defined as g-moles of the intercalated lithium per g-mole of iron phthalocyanine, at a fixed set of temperature and pressure conditions are presented. In addition, a proposed expression for the evaluation of lithium diffusion coefficient in solid iron phthalocyanine as a function of both x and temperature, and the experimental results from the ongoing research/development work on the lithium/iron phthalocyanine cells are included.