An Efficient Monte Carlo-Based Solver For Thermal Radiation In Participating Media, Joseph Farmer, Somesh Roy

Mechanical Engineering Faculty Research and Publications

Monte Carlo-based solvers, while well-suited for accurate calculation of complex thermal radiation transport problems in participating media, are often deemed computationally unattractive for use in the solution of real-world problems. The main disadvantage of Monte Carlo (MC) solvers is their slow convergence rate and relatively high computational cost. This work presents a novel approach based on a low-discrepancy sequence (LDS) and is proposed for reducing the error bound of a Monte Carlo-based radiation solver. Sobols sequence – an LDS generated with a bit-by-bit exclusive-or operator – is used to develop a quasi-Monte Carlo (QMC) solver for thermal radiation in this …

Combustion Dynamics And Heat Transfer In An Ultra Compact Combustor, Brian T. Bohan

Theses and Dissertations

The Ultra Compact Combustor (UCC) is an innovative combustion system alternative to a traditional turbine engine burner with the potential to improve engine efficiency with a reduced combustor volume. The UCC shortens the axial length of the combustor, and therefore reduces engine weight, by burning in an annulus and swirling the reactants in the circumferential direction. These length and weight improvements can directly lead to an increased thrust-to-weight rating of the engine. The present research included five objectives which advanced the UCC concept on four fronts; cooling UCC turbine vanes, advanced computational modeling of UCC systems, system air split control …

Thermophotovoltaic Devices: Combustion Chamber Optimization And Modelling To Maximize Fuel Efficiency, Arnold Chris Toppo, Ernesto Marinero, Zhaxylyk Kudyshev

The Summer Undergraduate Research Fellowship (SURF) Symposium

Currently, 110 billion cubic meters of natural gas (primarily methane), a potent greenhouse gas, are flared off for environmental and safety reasons. This process results in enough fuel to provide the combined natural gas consumption of Germany and France. The research team developed a thermophotovoltaic device to convert thermal energy to electricity at a high efficiency using proprietary emitters and combustion system. With the current focus being fuel efficiency and the combustion process, the assembly was simulated using ANSYS Fluent modelling software and the following parameters were optimized: air/fuel ratios, flow rates, and inlet sizes. Simultaneously the heat transfer across …

Pore-Resolving Simulation Of Char Particle Gasification Using Micro-Ct, Greg Hingwah Fong, Scott Jorgensen, Simcha L. Singer

Mechanical Engineering Faculty Research and Publications

Understanding the interaction between transport, reaction and morphology at the scale of individual char particles is important for optimizing solid fuel gasification and combustion processes. However, most particle-scale models treat porous char particles as an effective porous continuum, even though the presence of large, irregular macropores, voids and fractures render such upscaled treatments mathematically invalid, and the models non-predictive. A new modeling framework is therefore proposed to elucidate the impact of morphology on char particle gasification and combustion. A pore-resolving, transient, three-dimensional simulation for gasification of a realistic coal char particle is developed based on X-ray micro-computed tomography (micro-CT). The …

Kinetic Study Of Free Radical-Radical Reactions Of Combustion Importance At Elevated Pressures, Chao Yan

Dissertations

Combustion mechanisms consist of hundreds elementary reactions of free radicals and stable molecules. Radical-radical elementary reactions play important roles due to the high concentration in which free radicals are accumulated in combustion systems. Radical-radical reactions are typically multi-channel. Some of the channels might be of chain propagation or even chain branching nature, while other channels might be of chain termination nature. The relative importance of different channels is pressure dependent. Compared to radical-molecule reactions, radical-radical reactions are much less studied. This is due to the difficulties of well characterized quantitative production of radical species as well as due to the …

Simulation Of An Ethylene Flame With Turbulence, Soot And Radiation Modeling, Santu Golder

Electronic Theses and Dissertations

This thesis will investigate soot models that are available in commercial codes. We will look at the effect of turbulence models, gravity, soot models and radiation. Simulations will be compared to Coppalle and Joyeux [1]. The flame is an ethylene air diffusion flame at a Reynolds number of 5700. Simulations show the SST turbulence model, one-step soot model and Rosseland radiation model including gravity agree well with experimental data (temperature and soot). Flamelet soot modeling from Carbonell et al. [2] and flamelet radiation modeling from Doom [3] has been incorporated and compared as well.

Design And Experimental Study Of A High Pressure And Supercritical Methane-Oxygen Burner, A S M Arifur Rahim Chowdhury

Open Access Theses & Dissertations

Directly heated supercritical oxy-fuel power cycles have potential to offer a higher thermal efficiency and lower pollutant emissions compared to existing power cycles. Recent thermodynamic analysis of the cycle performed by several groups including the UTEP-Air Liquide research team show that combustion in the vicinity of 300 bar pressure and 1000-1400 K temperature allows for relatively high system efficiencies while operating within the limit of practical combustor materials. However, the realization of directly heated supercritical power cycle requires combustion systems be designed to operate in supercritical conditions and at temperature far below the blowout limit of conventional flames (above 1500 …

NoX Formation In Light-Hydrocarbon, Premixed Flames, Robert T. Hughes

Theses and Dissertations--Mechanical Engineering

This study explores the reactions and related species of NO_x pollutants in methane flames in order to understand their production and consumption during the combustion process. To do this, several analytical simulations were run to explore the behavior of nitrogen species in the pre-flame, post- flame, and reaction layer regions. The results were then analyzed in order to identify all "steady-state" species in the flame as well as the determine all the unnecessary reactions and species that are not required to meet a defined accuracy. The reductions were then applied and proven to be viable.

Investigation Of The Performance And Emissions Characteristics Of Dual Fuel Combustion In A Single Cylinder Idi Diesel Engine, Johnnie L. Williams Jr

Electronic Theses and Dissertations

Restrictions in the allowable exhaust gas emissions of diesel engines has become a driving factor in the design, development, and implementation of internal combustion (IC) engines. A dual fuel research engine concept was developed and implemented in an indirect injected engine in order to research combustion characteristics and emissions for non-road applications. The experimental engine was operated at a constant speed and load 2400 rpm and 5.5 bar indicated mean effective pressure (IMEP). n-Butanol was port fuel injected at 10%, 20%, 30%, and 40% by mass fraction with neat ultra-low sulfur diesel (ULSD#2). Peak pressure, maximum pressure rise rates, and …

A Multi-Scale Approach For Modeling Shock Ignition And Burn Of Granular Hmx, Pratap Thamanna Rao

LSU Doctoral Dissertations

Deflagration-to-detonation transition (DDT) in confined, low-density granular HMX (65%-85% Theoretical Maximum Density, TMD) occurs by a complex mechanism that involves compaction shock interactions within the material. Piston driven DDT experiments indicate that detonation is abruptly triggered by the interaction of a strong burn-supported secondary shock and a piston-supported primary (input) shock, where the nature of the interaction depends on initial packing density and primary shock strength. These interactions influence transition by affecting hot-spot formation within the micro-structure during pore collapse. In this study, meso-scale simulations of hot-spot formation in shock loaded granular HMX are used to guide the development of …

Fundamental Studies Of Flame Structure Through Laser Plasma Diagnostics, Wendong Wu

McKelvey School of Engineering Theses & Dissertations

Increasing concerns about air pollution and global climate change are drawing attention to the need for efficiency improvements and emission reductions for combustion processes, which account for more than 85% of energy production in United States. Combustion efficiency and emissions are affected by the mixing and reacting of fuel and oxidizer. Understanding such behavior plays a critical role in flame structure studies and combustion optimization. However, experimentally obtaining mixture fraction, which is a widely used quantity to describe the mixing behavior, has proven to be a challenge, especially for heavier hydrocarbon fuels or fuel rich flames. Moreover, measuring flame temperature …

Additive Manufacturing Of High Solids Loading Hybrid Rocket Fuel Grains, Stephen P. Johnson, Michael Baier, Ibrahim E. Gunduz, Steven F. Son

The Summer Undergraduate Research Fellowship (SURF) Symposium

Hybrid rocket motors offer many of the benefits of both liquid and solid rocket systems. Like liquid engines, hybrid rocket motors are able to be throttled, can be stopped and restarted, and are safer than solid rocket motors since the fuel and oxidizer are in different physical states. Hybrid rocket motors are similar to solid motors in that they are relatively simple and have a high density-specific impulse. One of the major drawbacks of hybrid rocket motors is a slower burning rate than solid rocket motors. Complex port geometries provide greater burning surface area to compensate for lower burning rates …

Design Of A 1 Megawatt Heat Input Direct Power Extraction System For Advanced Topping Cycles, Brian Matthew Lovich

Open Access Theses & Dissertations

Power development has become a standard for living; as such more efficient and cleaner methods are desired. One such method is that of the direct power extraction system utilizing Magnetohydrodynamic properties. This paper will discuss the combustor designed and developed for a direct power extraction system at the 1 MW heat input range. A short history of the power systems utilized with a focus on the direct power class will be conducted in the first chapter to give insight into the benefits of using the direct power system. Then a literature review the fundamentals of direct power systems will be …

Reaction Tuning Of Selectively Deposited Nano-Thermite Inks For Thrust And Heat Deposition, Raghav Ramachandran

Open Access Theses

Currently there is very little systematic work that quantifies the performance of energetic materials in terms of thrust or heat deposition applied to electronic circuits. A better understanding of the interactions between nano-scale energetic materials and electronic systems, as a function of stoichiometry is needed for enhanced defeat. Both of these needs are addressed in this research. Formulations of Al-CuO and Al-Bi2O3 nano-thermites were prepared at different equivalence ratios and selectively deposited onto silicon substrates and thrust and heat deposition of these materials was quantified. Both nano-thermite systems produced maximum thrust near stoichiometric ratios, and more fuel-rich mixtures led to …

The Feasibility Of Utilising Compressed Natural Gas As Part Of A Systematic Approach To Establishing The Necessary Groundwork For The Hydrogen Based Transport Economy, James Brunton, John Howlett, David Kennedy

Conference Papers

One key objective for vehicle manufacturers is to develop technology and infrastructure to facilitate the progression from combustion to conversion by the year 2050. In the short to medium term however, the combustion of fossil fuels such as petrol and diesel, coupled with advanced transmission innovations and emission control technology that are governed by strict Euro VI regulations appears to be the main path forward for the transport sector and the environment. This paper presents the feasibility of utilising the developing compressed natural gas network capabilities as part of a systematic approach to establishing the necessary groundwork for a hydrogen …

Use Of Green Mussel Shell As A Desulfurizer In The Blending Of Low Rank Coal-Biomass Briquette Combustion, Mahidin Mahidin, Asri Gani, M. Reza Hani, Muhammad Syukur, Hamdani Hamdani, Khairil Khairil, Samsul Rizal, Abdul Hadi, T.M.I. Mahlia

Makara Journal of Technology

Calcium oxide-based material is available abundantly and naturally. A potential resource of that material comes from marine mollusk shell such as clams, scallops, mussels, oysters, winkles and nerites. The CaO-based material has exhibited a good performance as the desulfurizer or adsorbent in coal combustion in order to reduce SO2 emission. In this study, pulverized green mussel shell, without calcination, was utilized as the desulfurizer in the briquette produced from a mixture of low rank coal and palm kernel shell (PKS), also known as bio-briquette. The ratio of coal to PKS in the briquette was 90:10 (wt/wt). The influence of green …

Data Driven Low-Bandwidth Intelligent Control Of A Jet Engine Combustor, Nathan L. Toner

Open Access Dissertations

This thesis introduces a low-bandwidth control architecture for navigating the input space of an un-modeled combustor system between desired operating conditions while avoiding regions of instability and blow-out. An experimental procedure is discussed for identifying regions of instability and gathering sufficient data to build a data-driven model of the system's operating modes. Regions of instability and blow-out are identified experimentally and a data-driven operating point classifier is designed. This classifier acts as a map of the operating space of the combustor, indicating regions in which the flame is in a "good" or "bad" operating mode. A data-driven predictor is also …

An Experimental Investigation Of Self-Excited Combustion Dynamics In A Single Element Lean Direct Injection (Ldi) Combustor, Rohan M. Gejji

Open Access Dissertations

The management of combustion dynamics in gas turbine combustors has become more challenging as strict NOx/CO emission standards have led to engine operation in a narrow, lean regime. While premixed or partially premixed combustor configurations such as the Lean Premixed Pre-vaporized (LPP), Rich Quench Lean burn (RQL), and Lean Direct Injection (LDI) have shown a potential for reduced NOx emissions, they promote a coupling between acoustics, hydrodynamics and combustion that can lead to combustion instabilities. These couplings can be quite complex, and their detailed understanding is a pre-requisite to any engine development program and for the development of predictive capability …

The Validation And Verification Of Les Modeling Using Kiva, David Fyda

UNLV Theses, Dissertations, Professional Papers, and Capstones

In recent years, the use of large-eddy simulation (LES) has grown into new research methods. LES is preferred when compared to Reynold’s Averaged Navier Stokes (RANS), which separates velocity components into steady and fluctuating components. While RANS is relatively easy to implement, it does not fully resolve the range of turbulence eddies and has limitations that make it inaccurate in many practical circumstances. Direct numerical simulation, DNS, fully resolves all turbulent eddies to the smallest grid scale, but requires an extremely fine grid. This makes it computationally impractical to use as the computational power required to solve even the simplest …

Gasoline Confined In Nano-Porous Media, Matthew Giso

Honors Theses

The heat of combustion was determined for gasoline confined in nano-porous media of differing pore size by bomb calorimetry. The heat of combustion of the confined fuels was comparable to that of bulk within the experimental uncertainty. This suggests that all of the confined fuel burns without any flame quenching and no chemical interactions at the interface between pore walls and fuel mitigate combustion.

Application Of A Multi-Zone Model For The Prediction Of Species Concentrations In Rapid Compression Machine Experiments, David Wilson

Master's Theses (2009 -)

Accurate chemical kinetic models, which predict species evolution and heat release rates in chemically reactive systems, are essential for further advancements in fuel and combustion technology. An experimental facility that is widely used for evaluating the accuracy of kinetic models is a rapid compression machine (RCM), which creates a well-defined reaction environment by compressing a reactive mixture inside a chamber. Generally, RCM experiments are conducted in order to obtain ignition delay data. However, chemical speciation data provides greater insight into reaction pathways, and is therefore a more rigorous benchmark for validating kinetic models. In order for a chemical kinetic model …

Economical Retrofit System To Reduce Cooking Emissions In Third World Dwellings, Jonathan Vanzummeren, Tyler Sturgeon, Ben Dalessandro

Williams Honors College, Honors Research Projects

Abstract:

The purpose of this document is to propose and demonstrate the feasibility and effectiveness of substituting an open flame biomass cooking process with a closed system with the capabilities of sustaining an adequate fire. Clay ovens or “chulhas” are the traditional piece of cooking equipment used in poorer areas of the world. They are often built inside cramped one-room housing units with little or no ventilation. The emissions released from burning fuel sources such as wood, coal, or animal waste bring with them detrimental and often fatal health problems and results in approximately 1.3 million deaths per year.

The …

Performance Evaluation Of Palm Oil-Based Biodiesel Combustion In An Oil Burner, Abdolsaeid Ganjehkaviri, Mohammad Nazri Mohd Jaafar, Seyed Ehsan Hosseini, Anas Basri Musthafa

Faculty Publications - Mechanical Engineering

This paper presents an experimental investigation of the combustion characteristics of palm methyl ester (PME), also known as palm oil-based biodiesel, in an oil burner system. The performance of conventional diesel fuel (CDF) and various percentages of diesel blended with palm oil-based biodiesel is also studied to evaluate their performance. The performance of the various fuels is evaluated based on the temperature profile of the combustor's wall and emissions, such as nitrogen oxides (NOx) and carbon monoxide (CO). The combustion experiments were conducted using three different oil burner nozzles (1.25, 1.50 and 1.75 USgal/h) under lean (equivalence ratio (φ) = …

Combustion Of Novel Thermite Mixtures For Iodine Generation, Sergio Emanuel Guerrero

Open Access Theses & Dissertations

Halogen-containing reactive materials could be used for mitigating the spread of hazardous, active biological microorganisms aerosolized as a result of explosion. The present work exhibits experimental results on the combustion of mechanically alloyed aluminum-iodine (Al-I2) powder mixed with Fe2O3, CuO, MoO3, Bi2O3, and I2O5. Wet mixing was used to prepare the samples, which were then compacted into pellets and ignited with a CO2 laser. A chamber was designed and built to accommodate for combustion and collection of products, and the available laser ignition setup was modified to enable combustion experiments with rapidly burning gas-generating mixtures. High-speed video recording was used …

Design Of A Thermal Management System For An Oxy-Methane Direct Power Extraction Combustor, Jad Gerges Aboud

Open Access Theses & Dissertations

The overarching goal of this Thesis is to present the design of a thermal management system for an oxy-methane direct power extraction combustor. The design is initiated by performing a 2D analysis on the combustor geometry and then using these results in a 3D model. This is done by using results for heat transfer coefficient and temperatures found from the 2D simulation and importing these to the 3D model. The approach used here couples the combustion process, heat transfer through the chamber wall, and fluid flow behaviors in order to observe the thermal characteristics of the combustor during operation. This …

High Pressure Combustion And Supersonic Jet Ignition For H2/Air, Michael G. Woodworth, Sayan Biswas, Li Qiao

The Summer Undergraduate Research Fellowship (SURF) Symposium

There are many incentives to increase the fuel efficiency of combustion processes. This paper looks at two available options to achieve this goal. The former aims to develop an experimental method that can analyze combustion at extremely high pressures to improve the understanding of high pressure H2/air combustion. Experimental data has been lacking a suitable combustion diagnostic to visualize high pressure combustion processes, making it difficult to improve the process. Improvement of x-ray diffraction tomography in a windowless combustor makes it possible to see flame propagation at high pressure. The procedure and chamber are still in the design phase, yet …

Sample Size Effect On Combustion Analysis, Osueke C. O, Uguru Okorie Daniel, Aondoyila Kuhe

Innovative Research Publications IRP India

Engine parameters vary from one cycle to the other and this makes engine analysis with data from a single working cycle insufficient in capturing or modelling an engine behaviour. The variation observed in engine has necessitated the use sample sizes of data obtained during an engine operation to obtain results that are representative of the engine being investigated. Research has shown that the use of very large data sample size increases the storage needed and processing time and does not necessary give better results over results obtained with lesser sample sizes. The number of sample size to use for analysis …

Effect Of N-Butanol And Diethyl Ether As Oxygenated Additives On Combustion-Emission-Performance Characteristics Of A Multiple Cylinder Diesel Engine Fuelled With Diesel-Jatropha Biodiesel Blend

Faculty of Engineering University of Malaya

Jatropha biodiesel is considered as one of the most prospective renewable energy sources of Malaysia in recent years. Hence, an investigation was conducted for the improvement of jatropha biodiesel-diesel blend with the addition of 5-10% n-butanol and diethyl ether by vol. which are commonly known as oxygenated cold starting additive. Engine tests were conducted at variable speed, ranging from 1000 rpm to 3000 rpm at constant 80 N m torque on a 4-cylinder turbocharged indirect injection diesel engine. Engine performance parameters like brake specific fuel consumption, brake specific energy consumption, brake thermal efficiency and engine emissions like carbon monoxide, unburned …

La0.7Sr0.3Fe0.7Ga0.3O3-Δ As Electrode Material For A Symmetrical Solid Oxide Fuel Cell, Zhibin Yang, Yu Chen, Chao Jin, Guoliang Xiao, Minfang Han, Fanglin Chen

Fanglin Chen

In this research, La_0.7Sr_0.3Fe_0.7Ga_0.3O_3−δ (LSFG) perovskite oxide was successfully prepared using a microwave-assisted combustion method, and employed as both anode and cathode in symmetrical solid oxide fuel cells. A maximum power density of 489 mW cm⁻² was achieved at 800 °C with wet H₂ as the fuel and ambient air as the oxidant in a single cell with the configuration LSFG|La_0.8Sr_0.2Ga_0.83Mg_0.17O_3−δ|LSFG. Furthermore, the cells demonstrated good stability in H₂ and acceptable sulfur tolerance.

The Study Of Ionization In A Military, Heavy-Duty, Diesel Engine, Steven Zielinski

Wayne State University Theses

This thesis is an investigation of ionization in a military, heavy-duty, diesel engine. Ionization is a phenomenon which occurs in both spark-ignited and diesel engines. During the reactions of combustion, charged molecules and electrons are produced. The current produced, ion current, from these charges can be measured. The measurement of ion current can serve as an in-cylinder diagnostic for closed-loop engine control strategies. In this work, a literature review was performed to survey previous work as it pertains to ionization in diesel engines. In addition, a detailed description and comparison of the HEUI injection system was made to HPCR. This …