Spark Discharge Coupled Laser Multicharged Ion Source,
2015
Old Dominion University
Spark Discharge Coupled Laser Multicharged Ion Source, Md. Haider A. Shaim, Hani E. Elsayed-Ali
Electrical & Computer Engineering Faculty Publications
A spark discharge is coupled to a laser multicharged ion source to enhance ion generation. The laser plasma triggers a spark discharge with electrodes located in front of the ablated target. For an aluminum target, the spark discharge results in significant enhancement in the generation of multicharged ions along with higher charge states than observed with the laser source alone. When a Nd:YAG laser pulse (wavelength 1064 nm, pulse width 7.4 ns, pulse energy 72 mJ, laser spot area on target 0.0024 cm2) is used, the total multicharged ions detected by a Faraday cup is 1.0 nC with …
Development And Testing Of A 325 Mhz Β0= 0.82 Single-Spoke Cavity,
2015
Old Dominion University
Development And Testing Of A 325 Mhz Β0= 0.82 Single-Spoke Cavity, C. S. Hopper, Hyekyoung Park, J. R. Delayen
Physics Faculty Publications
A single-spoke cavity operating at 325 MHz with geometric beta of 0.82 has been developed and tested. Initial results* showed high levels of field emission which limited the achievable gradient. Several rounds of helium processing significantly improved the cavity performance. Here we discuss the development process and report on the improved results.
Crab Cavity And Cryomodule Development For Hl-Lhc,
2015
Old Dominion University
Crab Cavity And Cryomodule Development For Hl-Lhc, F. Carra, A. A. Carvalho, K. Artoos, S. Atieh, I. A. Santillana, S. Belomestnykh, A. Boucherie, J. P. Brachet, K. Brodzinski, G. Burt, S. U. De Silva, J. R. Delayen, R. Olave, H. Park
Physics Faculty Publications
The HL-LHC project aims at increasing the LHC luminosity by a factor 10 beyond the design value. The installation of a set of RF Crab Cavities to increase bunch crossing angle is one of the key upgrades of the program. Two concepts, Double Quarter Wave (DQW) and RF Dipole (RFD) have been proposed and are being produced in parallel for test in the SPS beam before the next long shutdown of CERN accelerator’s complex. In the retained concept, two cavities are hosted in one single cryomodule, providing thermal insulation and interfacing with RF coupling, tuning, cryogenics and beam vacuum. This …
Design Of Dressed Crab Cavities For The Hl-Lhc Upgrade,
2015
Old Dominion University
Design Of Dressed Crab Cavities For The Hl-Lhc Upgrade, C. Zanoni, K. Artoos, S. Atieh, I. Aviles-Santillana, S. Belomestnykh, I. Ben-Zvi, J.P. Brachet, G. Burt, R. Calaga, O. Captina, S. U. De Silva, J. R. Delayen, A. May, K. Marinov, R. Olave, H. Park, N. Templeton
Physics Faculty Publications
The HL-LHC upgrade relies on a set of RF crab cavities for reaching its goals. Two parallel concepts, the Double Quarter Wave (DQW) and the RF Dipole (RFD), are going through a comprehensive design process along with preparation of fabrication in view of extensive tests with beam in SPS. High Order Modes (HOM) couplers are critical in providing damping in RF cavities for operation in accelerators. HOM prototyping and fabrication have recently started at CERN. In this paper, an overview of the final geometry is provided along with an insight in the mechanical and thermal analyses performed to validate the …
Engineering Design And Prototype Fabrication Of Hom Couplers For Hl-Lhc Crab Cavities,
2015
Old Dominion University
Engineering Design And Prototype Fabrication Of Hom Couplers For Hl-Lhc Crab Cavities, C. Zanoni, S. Atieh, I. Aviles Santillana, S. Belomestnykh, G. Burt, R. Calaga, S. U. De Silva, J. R. Delayen, R. Olave, H. Park
Physics Faculty Publications
The High-Luminosity upgrade for the LHC relies on a set of RF Crab Cavities for reaching its goals. Two parallel concepts, the Double Quarter Wave (DQW) and the RF Dipole (RFD), are going through a comprehensive design process along with preparation of fabrication in view of extensive tests with beam in SPS. High Order Modes (HOM) couplers are critical in providing damping in RF cavities for operation in accelerators. HOM prototyping and fabrication have recently started at CERN. In this paper, an overview of the final shape is provided along with an insight in the mechanical and thermal analyses performed …
Electromagnetic Design Of 400 Mhz Rf-Dipole Crabbing Cavity For Lhc High Luminosity Upgrade,
2015
Old Dominion University
Electromagnetic Design Of 400 Mhz Rf-Dipole Crabbing Cavity For Lhc High Luminosity Upgrade, S.U. De Silva, H. Park, J. R. Delayen, Z. Li
Physics Faculty Publications
The beam crabbing proposed for the LHC High Luminosity Upgrade requires two crabbing systems operating in both horizontal and vertical planes. In addition, the crabbing cavity design needs to meet strict dimensional constraints and functional specifications of the cavities. This paper presents the detailed electromagnetic design including em properties, multipole analysis, multipacting levels of the 400 MHz rf-dipole crabbing cavity.
Performance Evaluation Of Hl-Lhc Crab Cavity Prototypes In A Cern Vertical Test Cryostat,
2015
Old Dominion University
Performance Evaluation Of Hl-Lhc Crab Cavity Prototypes In A Cern Vertical Test Cryostat, K. G. Hernández-Chahín, A. Macpherson, C. Jarrige, M. Navarro-Tapia, R. Torres Sánchez, G. Burt, A. Tutte, S. U. De Silva
Physics Faculty Publications
Three proof-of-principle compact crab cavity designs have been fabricated in bulk niobium and cold tested at their home labs, as a first validation step towards the High Luminosity LHC project. As a cross check, all three bare cavities have been retested at CERN, in order to cross check their performance, and cross-calibrate the CERN SRF cold test facilities. While achievable transverse deflecting voltage is the key performance indicator, secondary performance aspects derived from multiple cavity monitoring systems are also discussed. Temperature mapping profiles, quench detection, material properties, and trapped magnetic flux effects have been assessed, and the influence on performance …
Superconducting Cavity For The Measurements Of Frequency, Temperature, Rf Field Dependence Of The Surface Resistance,
2015
Old Dominion University
Superconducting Cavity For The Measurements Of Frequency, Temperature, Rf Field Dependence Of The Surface Resistance, Hyekyoung Park, S.U. De Silva, J. R. Delayen
Physics Faculty Publications
In order to better understand the contributions of the various physical processes to the surface resistance of superconductors the ODU Center for Accelerator Science is developing a half-wave resonator capable of operating between 325 MHz and 1.3 GHz. This will allow the measurement of the temperature and rf field dependence of the surface resistance on the same surface over the range of frequency of interest for particle accelerators and identify the various sources of power dissipation.
Analysis Of A 750 Mhz Srf Dipole Cavity,
2015
Old Dominion University
Analysis Of A 750 Mhz Srf Dipole Cavity, Alejandro Castilla, J. R. Delayen
Physics Faculty Publications
There is a growing interest in using rf transverse deflecting structures for a plethora of applications in the current and future high performance colliders. In this paper, we present the results of a proof of principle superconducting rf dipole, designed as a prototype for a 750 MHz crabbing corrector for the Medium Energy Electron-Ion Collider (MEIC), which has been successfully tested at 4.2 K and 2 K at the Jefferson Lab’s Vertical Testing Area (VTA). The analysis of its rf performance during cryogenic testing, along with Helium pressure sensitivity, Lorentz detuning, surface resistance, and multipacting processing analysis are presented in …
Secondary Electron Yield Of Electron Beam Welded Areas Of Srf Cavities,
2015
Old Dominion University
Secondary Electron Yield Of Electron Beam Welded Areas Of Srf Cavities, M. Basovic, S. Popovic, M. Tomovic, L. Vuskovic, A. Samolov, F. Cuckov
Physics Faculty Publications
Secondary Electron Emission (SEE) is a phenomenon that contributes to the total electron activity inside the Superconducting Radiofrequency (SRF) cavities during the accelerator operation. SEE is highly dependent on the state of the surface. During electron beam welding process, significant amount of heat is introduced into the material causing the microstructure change of Niobium (Nb). Currently, all simulation codes for field emission and multipacting are treating the inside of the cavity as a uniform, homogeneous surface. Due to its complex shape and fabricating procedure, and the sensitivity of the SEE on the surface state, it would be interesting to see …
Experiment And Results On Plasma Etching Of Srf Cavities,
2015
Old Dominion University
Experiment And Results On Plasma Etching Of Srf Cavities, J. Upadhyay, Do Im, J. Peshl, S. Popovic, L. Vuskovic, A. -M. Valente-Feliciano, L. Phillips
Physics Faculty Publications
The inner surfaces of SRF cavities are currently chemically treated (etched or electro polished) to achieve the state of the art RF performance. We designed an apparatus and developed a method for plasma etching of the inner surface for SRF cavities. The process parameters (pressure, power, gas concentration, diameter and shape of the inner electrode, temperature and positive dc bias at inner electrode) are optimized for cylindrical geometry. The etch rate non-uniformity has been overcome by simultaneous translation of the gas point-of-entry and the inner electrode during the processing. A single cell SRF cavity has been centrifugally barrel polished, chemically …
Imperfection And Tolerance Analysis Of Hom Couplers For Odu/Slac 400 Mhz Crabbing Cavity,
2015
Old Dominion University
Imperfection And Tolerance Analysis Of Hom Couplers For Odu/Slac 400 Mhz Crabbing Cavity, S. U. De Silva, R. G. Olave, H. Park, J. R. Delayen, Z. Li
Physics Faculty Publications
In preparation for the LHC High Luminosity upgrade, a 400 MHz crab cavity has been developed jointly at ODU/SLAC, including two higher order mode couplers designed to dampen the wakefields in order to comply with the impedance budget specified for the LHC system. During fabrication, assembly, and processing of the couplers, a number of imperfections may arise that could modify the higher order mode spectrum and the associated impedance for each mode. We present here a detailed study of the imperfections of the horizontal- and vertical- HOM couplers, and the associated allowed tolerances for manufacture, assembly and processing.
Beam Dynamics Studies Of 499 Mhz Superconducting Rf-Dipole Deflecting Cavity System,
2015
Old Dominion University
Beam Dynamics Studies Of 499 Mhz Superconducting Rf-Dipole Deflecting Cavity System, S. U. De Silva, K. E. Deitrick, H. Park, J. R. Delayen
Physics Faculty Publications
A 499 MHz deflecting cavity has been designed as a three-way beam spreader to separate an electron beam into 3 beams. The rf tests carried out on the superconducting rf-dipole cavity have demonstrated that a transverse voltage of 4.2 MV can be achieved with a single cavity. This paper discusses the beam dynamics on a deflecting structure operating in continuous-wave mode with a relativistic beam. The study includes the analysis on emittance growth, energy spread, and change in bunch size including effects due to field non-uniformities.
Progress On The Design Of The Polarized Medium Energy Electron Ion Collider At Jlab,
2015
Old Dominion University
Progress On The Design Of The Polarized Medium Energy Electron Ion Collider At Jlab, F. Lin, S. A. Bogacz, P. D. Brindza, A Camsonne, E. Daly, Y. S. Derbenev, D. Douglas, R. Ent, D. Gaskell, R. L. Geng, A. Castilla, J. R. Delayen, C. E. Hyde, K. Park
Physics Faculty Publications
The Medium-energy Electron Ion Collider (MEIC) at JLab is designed to provide high luminosity and high polarization needed to reach new frontiers in the exploration of nuclear structure. The luminosity, exceeding 1033 cm-2s−1 in a broad range of the center-of-mass (CM) energy and maximum luminosity above 1034 cm-2s−1, is achieved by high-rate collisions of short small-emittance low-charge bunches made possible by high-energy electron cooling of the ion beam and synchrotron radiation damping of the electron beam. The polarization of light ion species (p, d, 3He) can be easily preserved and …
Effects Of Crab Cavities Multipole Content In An Electron-Ion Collider,
2015
Old Dominion University
Effects Of Crab Cavities Multipole Content In An Electron-Ion Collider, A. Castilla, V. S. Morozov, T. Satogata, J. R. Delayen
Physics Faculty Publications
The impact on the beam dynamics of the Medium Energy Electron-Ion Colider (MEIC) due to the multipole content of the 750 MHz crab cavity was studied using thin multipole elements for 6D phase space particle tracking in ELEGANT. Target values of the sextupole component for the cavity’s field expansion were used to perform preliminary studies on the proton beam stability when compared to the case of pure dipole content of the rf kicks. Finally, important effects on the beam sizes due to non-linear components of the crab cavities’ fields were identified and some criteria for their future study were proposed.
Effects Of Plasma Processing On Secondary Electron Yield Of Niobium Samples,
2015
Old Dominion University
Effects Of Plasma Processing On Secondary Electron Yield Of Niobium Samples, M. Basovic, S. Popovic, M. Tomovic, L. Vuskovic, A. Samolov, F. Cuckov
Physics Faculty Publications
Impurities deposited on the surface of Nb during both the forming and welding of accelerator cavities add to the imperfections of the sheet metal, which then affects the overall performance of the cavities. This leads to a drop in the Q factor and limits the maximum acceleration gradient achievable per unit length of the cavities. The performance can be improved either by adjusting the fabrication and preparation parameters, or by mitigating the effects of fabrication and preparation techniques used. We have developed the experimental setup to determine Secondary Electron Yield (SEY) from the surface of Nb samples. Our aim is …
Modeling Crabbing Dynamics In An Electron-Ion Collider,
2015
Old Dominion University
Modeling Crabbing Dynamics In An Electron-Ion Collider, A. Castilla, V. S. Morozov, T. Satogata, J. R. Delayen
Physics Faculty Publications
A local crabbing scheme requires π/2 (mod π) horizontal betatron phase advances from an interaction point (IP) to the crab cavities on each side of it. However, realistic phase advances generated by sets of quadrupoles, or Final Focusing Blocks (FFB), between the crab cavities located in the expanded beam regions and the IP differ slightly from π/2. To understand the effect of crabbing on the beam dynamics in this case, a simple model of the optics of the Medium Energy Electron-Ion Collider (MEIC) including local crabbing was developed using linear matrices and then studied numerically over multiple turns (1000 passes) …
Peppo: Using A Polarized Electron Beam To Produce Polarized Positrons,
2015
Old Dominion University
Peppo: Using A Polarized Electron Beam To Produce Polarized Positrons, A. Adeyemi, G.L Gueye, P.A. Adderly, M. L. Stutzman, M. M. Ali, H. Areti, J. F. Benesch, L. S. Cardman, J. Clark, S. Covert, S. Golge, C. Hyde
Physics Faculty Publications
An experiment demonstrating a new method for producing polarized positrons has been performed at the CEBAF accelerator at Jefferson Laboratory. The PEPPo (Polarized Electrons for Polarized Positrons) concept relies on the production of polarized e+/e− pairs originating from the bremsstrahlung radiation of a longitudinally polarized electron beam interacting within a 1.0 mm tungsten pair-production target. This paper describes preliminary results of measurements using an 8.2 MeV/c electron beam with polarization 84% to generate positrons in the range of 3.1 to 6.2 MeV/c with polarization as high as ∼80%.
Single And Double Spin Asymmetries For Deeply Virtual Compton Scattering Measured With Clas And A Longitudinally Polarized Proton Target,
2015
Old Dominion University
Single And Double Spin Asymmetries For Deeply Virtual Compton Scattering Measured With Clas And A Longitudinally Polarized Proton Target, S. Pisano, A. Biselli, S. Niccolai, K. Adhikari, D. Adikaram, M. J. Amaryan, S. E. Kuhn, L. B. Weinstein, Z. W. Zhao, Clas Collaboration
Physics Faculty Publications
Single-beam, single-target, and double spin asymmetries for hard exclusive electroproduction of a photon on the proton →e→p~ → e'p'γ are presented. The data were taken at Jefferson Lab using the CEBAF large acceptance spectrometer and a longitudinally polarized 14NH3 target. The three asymmetries were measured in 165 four-dimensional kinematic bins, covering the widest kinematic range ever explored simultaneously for beam and target-polarization observables in the valence quark region. The kinematic dependences of the obtained asymmetries are discussed and compared to the predictions of models of generalized parton distributions. The measurement of three DVCS spin observables …
Double Spin Asymmetries Of Inclusive Hadron Electroproduction From A Transversely Polarized He-3 Target,
2015
Old Dominion University
Double Spin Asymmetries Of Inclusive Hadron Electroproduction From A Transversely Polarized He-3 Target, Y. X. Zhao, K. Allada, K. Aniol, J.R.M. Annand, T. Averett, F. Benmokhtar, M. Canan
Physics Faculty Publications
We report the measurement of beam-target double spin asymmetries (ALT) in the inclusive production of identified hadrons, →e + 3He↑ → h + X, using a longitudinally polarized 5.9-GeV electron beam and a transversely polarized 3He target. Hadrons (π±, K±, and proton) were detected at 16 ° with an average momentum ( Ph ) = 2.35 GeV/c and a transverse momentum (pT) coverage from 0.60 to 0.68 GeV/c. Asymmetries from the He-3 target were observed to be nonzero for π± production when the target was polarized …
