Electrocatalytic Oxidation Degradation Kinetics Of Oxalic Acid In A Cylindrical Electrochemical Reactor With Ti/Iro2-Ta2O5 Anode,
2013
College of Chemistry, Jilin University, Changchun130021, China;School of Chemistry and Chemical Engineering, Guangxi University, Nanning530004, China;
Electrocatalytic Oxidation Degradation Kinetics Of Oxalic Acid In A Cylindrical Electrochemical Reactor With Ti/Iro2-Ta2O5 Anode, Jing Su, Hai-Bo Lin, Hong Xu, Wei-Min Huang, Ya-Peng He
Journal of Electrochemistry
The electrocatalytic oxidation degradation kinetics of oxalic acid in a cylindrical electrochemical reactor with Ti/IrO2-Ta2O5 as an anode was studied. The relation between instantaneous current efficiency and organic concentration in bulk was established based on the two paths for direct electrochemical oxidations, and the theoretical model was verified by experiments. The experimental resultswere reasonably consistent with the established kinetic model. Furthermore, the competition between the two paths was explored with the modelparameter analysis.
Performance Of The Electro-Oxidation And Electro-Fenton Processes With A Bdd Anode For The Treatment Of Low Contents Of Pharmaceuticals In A Real Water Matrix,
2013
Laboratori d’ Eleetroqutmica dels Materials i del Medi Ambient, Departament de Qutmica Fisiea.Facultat de Outmica, Universitat de Barcelona, Marti i Franguès 1-11,08028 Barcelona, Spain
Performance Of The Electro-Oxidation And Electro-Fenton Processes With A Bdd Anode For The Treatment Of Low Contents Of Pharmaceuticals In A Real Water Matrix, Sirs Ignasi, Antonio Garrido Jos, Brillas Enric
Journal of Electrochemistry
Here, we report the performance of electro-oxidation and electro-Fenton with a boron-doped diamond (BDD) anode for the treatment of single and multicomponent solutions containing small amounts of pharmaceutical residues (i.e., 1 mg·L-1 paracetamol and/or 1 mg·L-1 salicylic acid) spiked into a real water matrix at pH 3.0. Electro-oxidation was performed in a BDD/Pt cell, whereas electro-Fenton was carried out in a BDD/air-diffusion cell to electrogenerate H2O2 at the cathode, always operating at constant current density. It was found that the decay of both pharmaceuticals by electro-oxidation was more rapid in the real water matrix than …
Electrochemical Treatment Of Heavy Metals With Self-Electricity Generation,
2013
Department of Environmental and Ecological Engineering, Laboratory for Elctrochemistry and Energy Storage,State Key Laboratory of Clean Energy Utlizaion, Zhejiang University, Hangzhou 310027, Zhejiang, China
Electrochemical Treatment Of Heavy Metals With Self-Electricity Generation, Wei Xu, Hui-Min Zhang, Zu-Cheng Wu
Journal of Electrochemistry
Heavy metal pollution is among the most serious environmental problems. Electrochemical method possesses many advantages like speediness and high efficiency, which develops rapidly. This review describes the aspect and application of heavy metals with self-electricity generation according to the primary batteries and fuel cells. Some examples to reduce heavy metal ions in the cathode are introduced. Applicability of this technology for removing heavy metals is also discussed. Employing electrochemical technology to treat contaminants with self-energy generation instead of exhausting energy will have a good prospect.
Electrochemical Behavior And Content Determination Of Paeonol At Poly Sudan Ⅲ Modified Electrode,
2013
Department of Pharmaceutical Analysis, Faculty of Pharmacy, Fujian Medical University, Fuzhou 350004, China;
Electrochemical Behavior And Content Determination Of Paeonol At Poly Sudan Ⅲ Modified Electrode, Yan-Jie Zheng, Ai-Lin Liu, Yun Lei, Xin-Hua Lin
Journal of Electrochemistry
The poly SudanⅢ modified electrode was characterized by electrochemical impedance spectroscopy（EIS）and cyclic voltammetry (CV), while the electrochemical behavior of paeonol was studied by cyclic voltammetry (CV). The result shows that the poly Sudan Ⅲ modified electrode exhibits excellent electrocatalytic effect on the oxidation of paeonol. The peak currents of differential pulse voltammetry are linear to the paeonol concentrations over the range of 3.0*10-7 ~ 2.2*10-5 mol·L-1. The detection limit has been estimated to be 5.0*10-8 mol·L-1. This method can be used for determination of paeonol content in real sample with satisfactory results.
Use Of Thermodynamic Models For Optimizing Fuel Treatment Processes,
2013
California State University - Long Beach
Use Of Thermodynamic Models For Optimizing Fuel Treatment Processes, Shawn Pj Kirby, Andrew Guenthner
STAR Program Research Presentations
Dyes are often added to fuels for tax purposes, but they cause degradation of the fuels. It would be advantageous to remove the dyes prior to their use in critical aerospace applications. Current technologies vary in the efficiency with which they can remove unwanted dyes from fuel sources. We have used Hansen Solubility Parameters to develop an “ideal solvent” that can be used to extract these dyes from fuel. This will also be applied to removal of sulfur compounds from fuels. Sulfur compounds in fuels create sulfates during combustion, which in turn react with water to make sulfuric acid. Sulfuric …
Fe, Co And Ni Adatoms Adsorbed On Silicene: A Dft Study,
2013
Illinois Mathematics and Science Academy
Fe, Co And Ni Adatoms Adsorbed On Silicene: A Dft Study, Kent Gang '14, Siva Gangavarapu '14, Matthew Deng '14, Glenn W. "Max" Mcgee, Ron Hurlbut, Michael Lee Dao Kang, Sean Ng Peng Nam, Harman Johll, Tok Eng Soon
Student Publications & Research
Two-dimensional materials have attracted much research attention given their intriguing properties. The latest member of this class of materials is silicene. In this work, we investigate the adsorption of Fe, Co and Ni adatoms on silicene using plane-wave density functional theory calculations within the Perdew-Burke-Ernzerhof parameterization of the generalized gradient approximation for the exchange-correlation potential. In particular, we calculate the binding energy, magnetization, and projected electronic configurations of these adatoms adsorbed at different sites on the silicene. Our calculations show that the hole site (i.e. in the centre of a hexagonal-like arrangement of Si atoms) is the most stable configuration …
Characterization By Nmr Of Reactants And Products Of Hydrofluoroether Isomers, Cf3(Cf2)3och3 And (Cf3)2c(F)Cf2och3, Reacting With Isopropyl Alcohol,
2013
University of Dayton
Characterization By Nmr Of Reactants And Products Of Hydrofluoroether Isomers, Cf3(Cf2)3och3 And (Cf3)2c(F)Cf2och3, Reacting With Isopropyl Alcohol, Howard Knachel, Vladimir Benin, William E. Moddeman, Janine C. Birkbeck, Thomas A. Kestner, Tayna L. Young
Chemistry Faculty Publications
The 3M Company product Novec™ 71IPA DL, a mixture of methoxyperfluorobutane, methoxyperfluoroisobutane and 4.5 wt.% isopropyl alcohol, has been found to be very stable at ambient temperature, producing fluoride at the rate of ~1 ppm/year. Our earlier kinetic and theoretical studies have identified the reaction mechanism. This paper identifies the 1H and 19F NMR chemical shifts, multiplicities, and coupling constants of reactants and the major products that result from aging the mixture in sealed Pyrex NMR tubes for periods up to 1.8 years at temperatures from 26 °C to 102 °C. Chemical shifts and coupling constants of fluorine …
Effect Of Ethyl Propionate On Low-Temperature Performance Of Lifepo4-Based Li-Ion Battery,
2013
Mcnair New Power Co., Ltd, Dongguan, Guangdong 523800, China
Effect Of Ethyl Propionate On Low-Temperature Performance Of Lifepo4-Based Li-Ion Battery, Xiao-Ping Li, Lian-Sheng Hao, Wei-Shan Li, Meng-Qing Xu, Li-Dan Xing
Journal of Electrochemistry
A linear carboxylic, ester ethyl propionate (EP), was used as the co-solvent of carbonates, ethylene carbonate (EC), ethyl-methyl carbonate (EMC) and dimethyl carbonate (DMC), and its effect on low-temperature performance of LiFePO4-based Li-ion battery was studied by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic charge-discharge test. The application of EP enhances the ionic conductivity of the electrolyte, improves the compatibility of the electrolyte with both LiFePO4 and graphite materials, and thus improves the low-temperature performance of LiFePO4-based Li-ion battery. The Li-ion battery using the optimized electrolyte of 1 mol·L-1 LiPF6/EC:EMC:DMC:EP …
Multifunctional Corrosion Inhibition Behavior Of Zn-Al Calcined Layered Double Hydroxides For Steel Rebar In Nacl Solution,
2013
State Key Laboratory of Physical Chemistry of Solid Surfaces, Department of Chemistry, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005, Fujian, China;
Multifunctional Corrosion Inhibition Behavior Of Zn-Al Calcined Layered Double Hydroxides For Steel Rebar In Nacl Solution, Xiao-Juan Zhang, Jing-Jing Wang, Shi-Gang Dong, Chang-Jian Lin
Journal of Electrochemistry
The Zn-Al layered double hydroxides (Zn-Al LDHs) and calcined products (Zn-Al CLDHs) were synthesized successfully under a routine air atmosphere. The results showed that both Zn-Al LDHs and Zn-Al CLDHs had obvious flake structures. The corrosion inhibition of Zn-Al CLDHs for steel rebar in NaCl solution was studied by electrochemical techniques. It was found that the corrosion rate of steel rebar decreased significantly after the steel rebar was treated by Zn-Al CLDHs in NaCl solution for 3 h. It was indicated that Zn-Al CLDHs could absorb Cl- and release OH- during their reconstruction process, which provided dual protection …
Influences Of The Cinnamic Acid On Zinc Electrodeposition At Glassy-Carbon Electrode,
2013
Department of Chemistry and Environment Science, Zhangzhou Normal University, Zhangzhou 363000, Fujian, China
Influences Of The Cinnamic Acid On Zinc Electrodeposition At Glassy-Carbon Electrode, Kai Li, Shen Chen, Shen-Na Liu, Bi-Sang Chen, Heng Lin, Guo-Liang Chen, Qing-Xiang Wang
Journal of Electrochemistry
The influences of cinnamic acid (CIN) on the mechanism of Zn deposition and nucleation kinetics onto glassy-carbon electrode were studied by cyclic voltammetry (CV) and chronoamperometry (CA). The results revealed that the zinc reduction took place via Zn2+ + 2e → Zn in the presence of CIN, but the kinetics of zinc deposition was changed and the formation rate of zinc nuclei was accelerated. In the absence of CIN, the mechanism of zinc nucleation followed the 3D-instantaneous diffusion-controlled nucleation, while the 3D-progressive diffusion-controlled nucleation in the presence of CIN. The addition of CIN reduced the nucleation rate, but increased …
Preparation And Characterization Of A Novel Composite Electrolyte Ceria-Sulfate For Intermediate Temperature Solid Oxide Fuel Cells,
2013
Department of Chemical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
Preparation And Characterization Of A Novel Composite Electrolyte Ceria-Sulfate For Intermediate Temperature Solid Oxide Fuel Cells, Ze Tong, Yi-Mei Yin, Jie-Wei Yin, Zi-Feng Ma
Journal of Electrochemistry
A novel composite electrolyte SDC-(Li/Na)2SO4 was prepared for intermediate temperature solid oxide fuel cells (ITSOFC). The phase structure and cross-sectional morphology were examined by XRD and SEM, respectively, and the ionic conductivity was investigated by AC impedance in a temperature range of 400 oC ~ 700 oC in air. It was found that the composite electrolyte was composed of two phases: crystal SDC and amorphous (Li/Na)2SO4. The conductivity of the composite electrolyte was significantly larger than that of SDC at intermediate temperatures (550 oC ~ 700 oC) and increased …
The Effect Of Precursors On Performance Of Lini0.5Co0.2Mn0.3O2 Cathode Material,
2013
Hangzhou Golden Horse Energy Tecnology Co., Ltd., Hangzhou 311215, China;
The Effect Of Precursors On Performance Of Lini0.5Co0.2Mn0.3O2 Cathode Material, Dong-Ge Hu, Zhang-Zhi Wang, Jia-Li Liu, Tao Huang, Ai-Shui Yu
Journal of Electrochemistry
Commercial LiNi0.5Co0.2Mn0.3O2 material is generally prepared by a combination of co-precipitation and solid state reaction method. The particle size distribution and morphology of Ni0.5Co0.2Mn0.3(OH)2 precursor have a great impact on the electrochemical performance of LiNi0.5Co0.2Mn0.3O2. In this work, the crystal structure and surface morphology of LiNi0.5Co0.2Mn0.3O2 prepared by three different precursors were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Particle size distribution, tap density and electrochemical performance were …
Preparation And Electrochemical Performance Of Hollow Carbon Spheres/Sulfur Composite,
2013
State Key Laboratory of Physical Chemistry of Solid Surfaces, Department of Chemistry, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005, Fujian, China;
Preparation And Electrochemical Performance Of Hollow Carbon Spheres/Sulfur Composite, Jun Zang, Hang Qian, Er-Man Zeng, Juan-Ni Fu, Ming-Sen Zheng, Quan-Feng Dong
Journal of Electrochemistry
Hollow carbon spheres were prepared by the PMMA template. Hollow carbon spheres/sulfur composite was made from sulfur and hollow carbon spheres as a conducting framework. The results of SEM and TEM showed that sulfur was uniformly filled in both of the shell and hollow core of hollow carbon spheres. The electrochemical performance of hollow carbon spheres/sulfur composite was characterized by the charge/discharge method. The results showed the excellent rate and cycle performance of hollow carbon spheres/sulfur composite. The reversible capacities of hollow carbon spheres/sulfur composite are 1145 mAh·g-1, 824 mAh·g-1, 702 mAh·g-1, 586 mAh·g …
Polypyrrole-Transition Metal-Oxygen Coordination Complexes As High Performance Lithium Storage Material,
2013
Institute Of Physics, Chinese Academy of Science, Beijing 100190, China;
Polypyrrole-Transition Metal-Oxygen Coordination Complexes As High Performance Lithium Storage Material, Ya Mao, Qingyu Kong, Bingkun Guo, Zhaoxiang Wang, Liquan Chen
Journal of Electrochemistry
No abstract provided.
Influence Of Electrode Hydrophobicity On Performance Of Alkaline Polymer Electrolyte Fuel Cells,
2013
College of Chemistry and Molecular Seiences, Wuhan University, Wuhan 430072, China
Influence Of Electrode Hydrophobicity On Performance Of Alkaline Polymer Electrolyte Fuel Cells, Li-Sheng Tan, Jing Pan, Yao Li, Lin Zhuang, Jun-Tao Lu
Journal of Electrochemistry
In the present work, we study the influence of the electrode hydrophobicity on the performance of alkaline polymer electrolyte fuel cells (APEFCs). QAPS or xQAPS is employed as the membrane and the ionomer, while PTFE is used as a hydrophobic additive in order to adjust the electrode hydrophobicity. We find that enhancing the hydrophobicity of anode can promote the performance of APEFCs, while a moderate hydrophobicity of cathode is required to achieve optimal performance. By using xQAPS as the electrolyte and adding some PTFE in the anode, a peak power density of 132 mW·cm-2 can be obtained at a …
Progress Of Lithium Rich Cathode Materials For Li-Ion Batteries,
2013
School of Chemistry and Chemical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
Progress Of Lithium Rich Cathode Materials For Li-Ion Batteries, Jie Zhang, Jiu-Lin Wang, Jun Yang
Journal of Electrochemistry
Lithium rich materials xLi2MnO3·(1-x)LiMO2 (0-1 and low cost. However, the large irreversible capacity during the first cycle, low rate capability and structure collapse during cycling remain impediments in developing these cathodes for applications. The structure analyses and charge/discharge mechanisms for lithium rich materials are currently main research contents. Although whether the lithium rich materials are solid solutions or composite is still controversial, oxygen release mechanism on the first charge 4.5 V plateau of lithium rich materials has come to consistency. Several modifications, such as bulk doping, surface coating and microstructure control, demonstrate promising strategies to …
Electrochemical Performance Of Al-Doped Spinel Limn2O4 Cathode Material For Li-Ion Batteries,
2013
Institute of New Energy Material Chemistry, Nankai University, Tianjin 300071, China;
Electrochemical Performance Of Al-Doped Spinel Limn2O4 Cathode Material For Li-Ion Batteries, Yong-Long Wang, Wen-Ge Wang, Qian Zhang, Xin Wang, Jian-Sheng Cao, Shi-Hai Ye
Journal of Electrochemistry
Spinel LiMn2O4, a cathode material for Li-ion batteries, is featured as good high-rate performance, low cost and environmental friendly. The pristine and Al-doped LiMn2O4 samples were prepared by sol-gel method. The structure and micromorphology of the as-prepared samples were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results demonstrated that the as-prepared LiMn2O4 samples had a typical cubic spinel structure and were composed of sphere-like particles with a diameter range of 300 ~ 500 nm. Galvanostatic charge-discharge tests showed that the LiMn2O4 samples doped …
Electrocatalytic Mechanism And Porous Electrode Mass Transfer Process In Membrane Electrode Assembly For Direct Methanol Fuel Cells,
2013
Department of Physical Chemistry, University of Science and Technology Beijing, Beijing 100083, China
Electrocatalytic Mechanism And Porous Electrode Mass Transfer Process In Membrane Electrode Assembly For Direct Methanol Fuel Cells, Xin-Dong Wang, Yi-Tuo Wang, Gui-Cheng Liu, Meng Wang, Zhe Tian
Journal of Electrochemistry
Direct methanol fuel cell (DMFC) is considered to be a promising commercial energy conversion device for portable electronics due to its many advantages. In order to improve the performance of DMFC, many companies and research institutes have been launching the deep research and obtaining a lot of conspicuous achievements. In this paper, the electrocatalytic mechanism and porous electrode mass transfer process in membrane electrode assembly (MEA) are analyzed. In addition, combined with the preparation process of MEA, multilayer ordered structures and internal transfer process of the cell, recent progresses of MEA in DMFC are discussed.
Fabrication And Performance Of Lani0.6Fe0.4O3-δCathode Modified By Coating With Gd0.2Ce0.8O2 For Intermediate Temperature Solid Oxide Fuel Cell,
2013
Institute of Fuel Cell, School of Mechanical Engineering, Shanghai jiaotong University, Shanghai 200240, China
Fabrication And Performance Of Lani0.6Fe0.4O3-δCathode Modified By Coating With Gd0.2Ce0.8O2 For Intermediate Temperature Solid Oxide Fuel Cell, Rui-Xuan Ren, Bo Huang, Xin-Jian Zhu, Yi-Xing Hu, Xiao-Yi Ding, Zong-Yao Liu, Ye-Bin Liu
Journal of Electrochemistry
The symmetric cell of LaNi0.6Fe0.4O3-δ/Sc0.1Zr0.9O1.95/LaNi0.6Fe0.4O 3-δ was fabricated with screen printing method. A LaNi0.6Fe0.4O3-δ (LNF) cathode was modified by coating with nano-sized gadolinium-doped ceria (GDC, Gd0.2Ce0.8O2) prepared using a simple combustion process within the pores of the cathode. According to the electrochemical impedance spectra (EIS), the polarization resistance of the pure LNF was 0.70 W·cm2 at 750 ºC, while 0.13 W·cm2 for the 21.3% GDC (by mass)-coated LNF cathode at the …
Optimization Of Electroless Silver Plating Process On Fabric Surface Without Activation And Sensitization,
2013
Key Laboratory of Science & Technology of Eco-Textile, Ministry of Education, Donghua University, Shanghai 201620, China
Optimization Of Electroless Silver Plating Process On Fabric Surface Without Activation And Sensitization, Bo Lian Wang, Ya Ping Zhao, Zai Sheng Cai
Journal of Electrochemistry
Silver was deposited homogeneously on the surface of polyamide fabric by electroless plating without activation and sensitization. The electroless silver plating process was optimized with the orthogonal array testing strategy. It is found that the optimum conditions are the electroless plating time of 50 min with the concentrations of silver nitrate, sodium hydroxide and ammonium hydroxide being 14 g·L-1, 6 g·L-1 and 130 mL·L-1, respectively. The surface morphologies, compositions, and phases of fabric samples were characterized by scanning electron microscopy and energy-dispersive X-ray spectrometry (SEM-EDS), X-ray diffraction (XRD). The wear-resisting property was tested by friction fastness …
