Nuclear Engineering Commons^™

Fundamental And Applied Experimental Investigations Of Corrosion Of Steel By Lbe Under Controlled Conditions: Kinetics, Chemistry, Morphology, And Surface Preparation, Allen L. Johnson, John Farley, Dale L. Perry

Transmutation Sciences Materials (TRP)

An innovative research program is proposed to investigate the corrosion of steel by lead alloys, and in particular lead-bismuth eutectic (LBE). In our previous work, some steels were found to be far more resistant to corrosion by LBE than others depending on surface preparation (cold working). This program would allow testing of crucial hypotheses about the causes of the observed increased corrosion resistance. We propose to build a new test facility at UNLV to expose steel samples to LBE as well as facilities to prepare steel samples as indicated by our work.

The unique capabilities of the test system will …

Neutron Multiplicity Measurements Of Target/Blanket Materials, Carter D. Hull, Denis Beller

Transmutation Sciences Physics (TRP)

To optimize the performance of accelerator driven transmutation systems (ADS), engineers will need to design the system to operate with a neutron multiplication factor just below that of a critical, or self-sustaining, system. This design criteria requires particle transport codes that instill the highest level of confidence with minimal uncertainty, because the larger the uncertainties in the codes, the larger the safety margin required in the design and the lower the efficiency of the ADS transmuter. For current design efforts, the MCNPX code is used to determine neutron production and transport for spallation neutron systems.

While providing a very useful …

Nuclear Criticality, Shielding, And Thermal Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Denis Beller

Separations Campaign (TRP)

The first step in any transmutation strategy is the separation of radionuclides in used nuclear fuel. The current separation strategy supporting the Advanced Fuel Cycle Initiative (AFCI) program is based on the use of a solvent extraction separation process to separate the actinides, fission products, and uranium from used commercial nuclear fuel, and on the use of pyrochemical separation technologies to process used transmuter fuels. To separate the fission products and transuranic elements from the uranium in used fuel, the national program is developing a new solvent extraction process, the Uranium Extraction Plus, or UREX+, process, based on the traditional …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

The goal of this project is to investigate the casting processes for metallic fuels to help design a process that minimizes the loss of the volatile actinide elements from the fuel.

The research effort centers on the development of advanced numerical models to assess conditions that significantly impact the transport of volatile actinides during the melt casting process and represents a joint effort between researchers at the University of Nevada, Las Vegas (UNLV) and Argonne National Laboratory (ANL).

Design And Evaluation Of Processes For Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

The goal of this research project is to provide technical support to process designers working on the development of the fuel cycles for transmutation applications. Detailed process models are developed to better define the impact of fuel choice on the transmuter fuel cycle, including relative process losses, waste generation, and plant capital cost. These process models provide insight regarding required plant size and number of plants needed to mesh with the fuel recycling line. They also determine requirements for automation.

Manufacturing models for large-scale production in a hot cell environment are also developed. Combined, these two models allow the assessment …

Design And Evaluation Of Processes For Transmuter Fuel Fabrication, Georg F. Mauer

Fuels Campaign (TRP)

• Project Objective: examine autonomous robotic fuel fabrication processes with regard to hot cell and equipment design, operations, and costs.

• Fabrication processes for different fuel types differ in terms of equipment types, throughput, and cost.

• Design options are restricted by the requirement to employ only radiation-hardened machinery and components

• Benefit to Department of Energy: decision support for the selection of the most suitable manufacturing process.

A Finite Subelement Generalization Of The Variational Nodal Method, M. A. Smith, Nicholas Tsoulfanidis, E. E. Lewis, G. Palmiotti, T. A. Taiwo

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

The variational nodal method is generalized by dividing each spatial node into a number of triangular finite elements designated as subelements. the finite subelement trial functions allow for explicit geometry representations within each node, thus eliminating the need for nodal homogenization. the method is implemented within the Argonne National Laboratory code VARIANT and applied to two-dimensional multigroup problems. Eigenvalue and pin-power results are presented for a four-assembly Organization for Economic Cooperation and Development/Nuclear Energy Agency benchmark problem containing enriched UO2 and mixed oxide fuel pins. Our seven-group model combines spherical or simplified spherical harmonic approximations in angle with isoparametric linear …

Investigation Of The Corrosion Of Steel By Lead-Bismuth Eutectic (Lbe) Using Scanning Electron Microscopy And X-Ray Photoelectron Spectroscopy, Daniel Koury

UNLV Theses, Dissertations, Professional Papers, and Capstones

Lead Bismuth Eutectic (LBE) has been proposed for use in programs for accelerator transmutation of waste. LBE is the leading candidate material as a spallation target and an option for the sub-critical blanket coolant. The corrosion of 316 and 316L stainless steels by LBE has been studied using UNLV's facilities for Scanning Electron Microscopy (SEM) and X-ray Photoelectron Spectroscopy (XPS). We have compared exposed and unexposed samples and studied the differences. Some amount of surface contamination is present on the samples and has been removed by ionbeam etching. The unexposed samples reveal typical stainless steel characteristics: a chromium oxide passivation …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #5, Georg F. Mauer

Fuels Campaign (TRP)

The fifth quarter of the project covered the following:

· Literature Search: The process of evaluating the pertinent literature continued.

· Mr. Richard Silva continued the development of a simulation model with a Waelischmiller hot cell robot. Rich will continue to develop detailed 3-D process simulation models as his M.Sc. thesis project.

· Dr. Mauer presented a paper at the ANS Winter annual meeting in Washington, D.C. titled: “Design and Evaluation of Processes for Transmuter Fuel Fabrication.”

· Concepts and Methods for Vision-Based Hot Cell Supervision and control (Ph.D. Student Jae-Kyu Lee )

· Dr. Mauer presented a paper at …

Development Of A Systems Engineering Model Of The Chemical Separations Process: Quarterly Progress Report 8/16/02- 11/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

Two activities are proposed in this Phase I task: the development of a systems engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model is the start of an integrated approach to the analysis of the materials separations associated with the AAA Program. A second portion of the project is to streamline and improve an integral part of the overall systems model, which is the software package AMUSE. AMUSE analyzes the UREX process and other related solvent extraction processes and defines many of the process streams that are integral …

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report August September October 2002, John Farley

Transmutation Sciences Materials (TRP)

We continued with sputter depth profiling of 316 and 316L steel samples that have been exposed to LBE. We also calibrated the sputter depth profiling using a sample of SiO₂ on Si, and the SEM. This is a valuable independent determination of the thickness of oxide layers.

In the laboratory, progress continues using the XPS machine. Experiments have been performed on steel samples using Argon ions to mill away the surface of the sample, thereby making measurements as a function of depth. This "ion beam milling" proceeds slowly through the oxide layer that covers the steel sample. We are …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (Aug. 01 – Oct. 31, 2002), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

After two month intensive work in LANL, some preliminary sensor calibration curves have been obtained. Further data analysis shall be performed to assess the theoretical and measured data. Also, a new experimental apparatus shall be designed and located in UNLV to continue the left work.

Technical Progress:

• A set of calibration curves of voltage vs. temperature ranging from 300⁰C to 500⁰C under various oxygen concentrations in liquid LBE for the YSZ oxygen sensor has been obtained and has been reported in one paper.

• A meeting with LBE committee and other faculty members in AAA …

University Of Nevada, Las Vegas Advanced Accelerator Applications University Participation Program: Quarterly Report, First Quarter Year 2 (March 2002 To May 2002), Anthony Hechanova

Transmutation Research Program Reports (TRP)

This Quarterly Report is a primary deliverable from the University of Nevada, Las Vegas (UNLV) Advanced Accelerator Applications (AAA) University Participation Program (UPP) Director to the U.S. Department of Energy (DOE) as described in the UNLV AAA proposal, and Statement of Work for the First Quarter Year 2 and AAA FY02 Work Package.

The UNLV AAA UPP Director implements the program’s administration using staff from the Harry Reid Center for Environmental Studies (HRC) to ensure that work conducted under the UNLV AAA UPP meets program objectives. The UNLV AAA program consists of four components: Program Support, Research Infrastructure Augmentation, International …

University Of Nevada, Las Vegas Advanced Accelerator Applications University Participation Program: Quarterly Report, Third Quarter Year 2 (Sept. 2002 To Nov. 2002), Anthony Hechanova

Transmutation Research Program Reports (TRP)

This Quarterly Report is a primary deliverable from the University of Nevada, Las Vegas (UNLV) Advanced Accelerator Applications (AAA) University Participation Program (UPP) Director to the U.S. Department of Energy (DOE) as described in the UNLV AAA proposal and Statement of Work for the Fourth Quarter.

The UNLV AAA UPP Director implements the program’s administration using staff from the Harry Reid Center for Environmental Studies (HRC) to ensure that work conducted under the UNLV AAA UPP meets program objectives. The UNLV AAA program consists of three components: Program Support, Research Infrastructure Augmentation, and Student Research.

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823 For Transmutation Applications: Annual Progress Report (September 2001 – August 2002), Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The purpose of this project is to evaluate the elevated temperature tensile properties of Alloy EP-823, a leading target material for accelerator-driven waste transmutation applications. This alloy has been proven to be an excellent structural material to contain the lead-bismuth-eutectic (LBE) nuclear coolant needed for fast spectrum operations. Very little data exist in the open literature on the tensile properties of this alloy. The test material will be thermally treated prior to the evaluation of its tensile properties at temperatures relevant to the transmutation applications. The deformation characteristics of tensile specimens, upon completion of testing, will be evaluated by surface …

Development Of A Systems Engineering Model Of The Chemical Separations Process, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

The AAA program is developing technology for the transmutation of nuclear waste to address many of the long-term disposal issues. An integral part of this program is the proposed chemical separations scheme. This process, as envisioned by Argonne National Laboratory (ANL) researchers, will be outlined later in this report.

Nearly all issues related to risks to future generations arising from long-term disposal of such spent nuclear fuel is attributable to ~1% of its content. This 1% is made up primarily of plutonium, neptunium, americium, and curium (the transuranic elements) and long-lived isotopes of iodine and technetium created as products from …

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Ii Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Multipacting is one of the major loss mechanisms in rf superconductivity cavities for accelerators. This loss mechanism limits the maximum amount of energy/power supported by the cavities. Optimal designs have been identified in others’ studies. In practice, these designs are not easily manufactured. Chemical etching processes used to polish the cavity walls result in a nonuniform surface etch. A nonuniform surface etch will leave some unclean areas with contaminants and micron size particles. These significantly affect mutipacting. Further, a nonuniform etch will leave areas with damaged grain structure, which is not good for superconducting properties. Typically, the depth of chemical …

Hydrogen-Induced Embrittlement Of Candidate Target Materials For Applications In Spallation-Neutron-Target Systems: Quarterly Progress Report (June 01 – August 31, 2002), Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate target materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including Alloy HT-9, Alloy EP 823 and Type 422 stainless steel. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these materials are being evaluated in environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. Further, the localized corrosion behavior of these alloys …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements: Quarterly Progress Report (June 1 – August 31, 2002), Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada Las Vegas (UNLV), the Idaho State University (ISU), and the Los Alamos National Laboratory (LANL) is to evaluate the feasibility of determining residual stresses in cold-worked, plastically-deformed, and welded materials using a nondestructive method based on positron annihilation spectroscopy. This technique uses γ-rays from a small MeV electron Linac to generate positrons inside the sample via pair production. This method is known to have capabilities of characterizing defects in thick specimens, that could not be accomplished by conventional positron technique or other nondestructive methods. The generated data will …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #4, Georg F. Mauer

Fuels Campaign (TRP)

The fourth quarter of the project covered the following:

• Literature Search: The process of evaluating the pertinent literature continued. Results are summarized.

• Mr. Richard Silva developed a simulation model with a Waelischmiller hot cell robot. Rich will continue to develop detailed 3-D process simulation models as his M.Sc. thesis project.

• Dr. Mauer visited CEA Cadarache and CEA Marcoule in France, the institute for transuranics in Karlsruhe, and the Framatome manufacturing plant in Lingen, Germany.

• Concepts and Methods for Vision-Based Hot Cell Supervision and control (Ph.D. Student Jae-Kyu Lee )

Design And Evaluation Of Processes For Fuel Fabrication: Year 1 Final Report, Georg F. Mauer

Fuels Campaign (TRP)

The project objective is the design and evaluation of manufacturing processes for transmuter fuel fabrication. The large-scale deployment of remote fabrication and refabrication processes will be required for all transmutation scenarios. Current program emphasis is on a five-year effort to determine the feasibility of transmutation as a technology to limit the need for repository storage of spent commercial fuel. The evaluation of the fabrication processes will create a decision support data base to document design, operations, and costs. Fabrication processes required for different fuel types differ in terms of equipment types, throughput, and cost. The year 1 project was focused …

Design And Evaluation Of Processes For Fuel Fabrication: Year 1 Final Report, Georg F. Mauer

Fuels Campaign (TRP)

The project objective is the design and evaluation of manufacturing processes for transmuter fuel fabrication. The large-scale deployment of remote fabrication and refabrication processes will be required for all transmutation scenarios. Current program emphasis is on a five-year effort to determine the feasibility of transmutation as a technology to limit the need for repository storage of spent commercial fuel. The evaluation of the fabrication processes will create a decision support data base to document design, operations, and costs. Fabrication processes required for different fuel types differ in terms of equipment types, throughput, and cost. The year 1 project was focused …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Task V: Final Report -Phase I 09/01/2001-08/30/2002, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the AAA proposed application. Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with only very sparse experimental data. Scientists have noticed that the concentration of oxygen dissolved in the liquid alloy could control the corrosion rate of steels exposed to Pb or Pb-Bi. At high …

Development Of A Systems Engineering Model Of The Chemical Separations Process: Quarterly Progress Report 5/16/02- 8/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

Two activities are proposed in this Phase I task: the development of systems engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model is the start of an integrated approach to the analysis of the materials separations associated with the AAA Program. A second portion of the project is to streamline and improve an integral part of the overall systems model, which is the software package AMUSE. AMUSE analyzes the UREX process and other related solvent extraction processes and defines many of the process streams that are integral to …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides: Quarterly Progress Report 5/16/02- 8/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

An important aspect of the Advanced Accelerator Applications (AAA) program is the development of a casting process by which volatile actinide element (i.e., americium) can be incorporated into metallic alloy fuel pins. The traditional metal fuel casting process uses an inductively heated crucible.

This process works well for the fabrication of metal fuel pins traditionally composed of alloys of uranium and plutonium, but does not work well when highly volatile actinides are included in the melt. The problem occurs both during the extended time period required to superheat the alloy melt as well as when the chamber must be evacuated. …

Corrosion Of Steel By Lead Bismuth Eutectic: Quarterly Report For May-June-July 2002, John Farley

Transmutation Sciences Materials (TRP)

The goal of this project is to understand the basic science of corrosion in the steel/LBE system.

We are taking more data, typically using the newly installed X-ray Photoelectron Spectrometry (XPS) apparatus, and analyzing our existing data. Undergraduate students Denise Parsons and Julia Manzerova have helped a great deal in the analysis of the data. We can obtain the elemental composition as a function of position within the sample. This gives clues to the migration of materials, the composition of the protective oxide layer, and the basic science of the corrosion process. We found dramatic differences between the exposed and …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Xiaolong Wu

UNLV Theses, Dissertations, Professional Papers, and Capstones

Fundamental issues related to the selection of a metallic fuel casting furnace design are presented and discussed including heating mechanisms, casting issues, crucible design, and issues related to the mass transport of americium. The process of evaluating all of these different criteria is undertaken to select a concept that would have the greatest chance of success for casting americium in a metallic fuel rod. Based on this evaluation process, a concept for the casting of metallic fuel pins containing high vapor pressure materials is selected and discussed. The important physics of this concept include mass transport of americium from the …

Modeling And Simulation Of The Chemical Etching Process In Niobium Cavities, Qin Xue

UNLV Theses, Dissertations, Professional Papers, and Capstones

Niobium Cavities are important parts of the integrated NC/SC high-power linear accelerator (linac) that can accelerate over 100 mA of protons to several GeV. Surface finish of the niobium cavity plays an important role of achieving the best performance of niobium cavity. The chemical etching techniques have been widely used.

Chemical etching of the inner surface of the cavity is achieved by circulating acid through it. The acid interacts with the surface and eliminates imperfections. During the etching process, a pipe with baffles is inserted within the cavity to direct the flow along the surfaces.

A 2-D, axisymmetric, steady state, …

Developing A Sensing System For The Measurement Of Oxygen Concentration In Liquid Pb-Bi Eutectic: Quarterly Progress Report (May 01 – July 31, 2002), Yingtao Jiang, Bingmei Fu, Woosoon Yim

Transmutation Sciences Materials (TRP)

Accurate measurement of the oxygen concentration in liquid Lead-Bismuth Eutectic (LBE) cooling system is critical in the active control of the corrosion at the interface between LBE and the stainless steel of transport tubes. Currently, LANL (Los Alamos National Laboratory) scientists have employed an automobile-style YSZ (Yttria Stabilized Zirconia) oxygen sensor unit to measure oxygen levels in an engineeringscaled LBE test system. Although the theoretical model for calculating oxygen concentration based on voltage measurement of YSZ sensor in static conditions is well understood, there is an urgent and strong need to obtain a complete set of calibration curves for YSZ …

Phase I: Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

The proposed research would be conducted in 3 phases. Each of the phases would be carried out over a one-year period. Phase I includes model development, analysis, and the selection of a new casting furnace design. The work discussed in this report was completed as Phase I. Phase II of the program will lead to more modeling and validation to evaluate the proposed furnace concept. Phase III would be a joint effort between UNLV and Argonne National Laboratory (ANL) to demonstrate the acceptable use of the new furnace in a simulated remote environment.

The Phase III work would include the …