Mechanical Engineering Commons^™

The Effect Of Elevated Water Content On Ethanol Combustion, Baine Bernard Breaux

LSU Master's Theses

Ethanol is currently being considered as a potential alternative to traditional fuels. However, the fuel offers a low return in terms of energy output per dollar invested when compared to fossil fuels. More than 1/3 of the cost associated with bio-ethanol production is devoted to distillation and water removal. This study seeks to validate the use of hydrous ethanol as a practical fuel to be used in lieu of fossil fuels or anhydrous ethanol. Success would reduce the production cost associated with ethanol fuel. Hydrous ethanol was burned in a swirl-stabilized combustor, air is introduced at a constant flow rate …

Implementation Of A Phenomenological Evaporation Model Into A Porous Network Simulation For Water Management In Low Temperature Fuel Cells, David L. Fritz Iii.

Dissertations, Master's Theses and Master's Reports - Open

A phenomenological transition film evaporation model was introduced to a pore network model with the consideration of pore radius, contact angle, non-isothermal interface temperature, microscale fluid flows and heat and mass transfers. This was achieved by modeling the transition film region of the menisci in each pore throughout the porous transport layer of a half-cell polymer electrolyte membrane (PEM) fuel cell. The model presented in this research is compared with the standard diffusive fuel cell modeling approach to evaporation and shown to surpass the conventional modeling approach in terms of predicting the evaporation rates in porous media.

The current diffusive …

Algorithms For Spacecraft Formation Flying Navigation Based On Wireless Positioning System Measurements, Shu Ting Goh

Dissertations, Master's Theses and Master's Reports - Open

Spacecraft formation flying navigation continues to receive a great deal of interest. The research presented in this dissertation focuses on developing methods for estimating spacecraft absolute and relative positions, assuming measurements of only relative positions using wireless sensors. The implementation of the extended Kalman filter to the spacecraft formation navigation problem results in high estimation errors and instabilities in state estimation at times. This is due tp the high nonlinearities in the system dynamic model. Several approaches are attempted in this dissertation aiming at increasing the estimation stability and improving the estimation accuracy.

A differential geometric filter is implemented for …

A New Control System For Left Ventricular Assist Devices Based On Patient-Specific Physiological Demand, George Faragallah, Yu Wan, Eduardo Divo, Marwan Simaan

Mechanical Engineering - Daytona Beach

A left ventricular assist device (LVAD) is a mechanical pump that helps patients with a heart failure (HF) condition. This pump works in parallel to the ailing heart and provides a continuous flow from the weak left ventricle to the ascending aorta. The current supplied to the pump motor controls the flow of blood. A new feedback control system is developed to automatically adjust the pump motor current to provide the blood flow required by the level of activity of the patient. The systemic vascular resistance (RS) is the only undeterministic variable parameter in a patient-specific model and also a …

The Key Ideas Of Mdw Viii: A Summary, Aaron Altman, Clive L. Dym, Ray Hurwitz, John W. Wesner

Mechanical and Aerospace Engineering Faculty Publications

This paper summarizes and highlights the presentations and discussions that took place during Mudd Design Workshop VIII, ‘Design Education: Innovation and Entrepreneurship,’ at Harvey Mudd College. This paper also describes both the key ideas that emerged from the presentations and discussions of the participating engineering design educators, practitioners and researchers, and the methodology used to capture and retain those ideas. Additionally, this paper proposes a framework of design competencies that were created and evolved by the workshop’s participants as a response to a question posed at one of the workshop sessions: ‘What are the minimum design competencies students should learn …

Asme Early Career Technical Journal (Front Matter), Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. i-xiv

Section 1: Bio-Medical/Bioengineering, Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 1-44

Section 2: Materials, Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 45-94

Section 3: Dynamic Systems & Control, Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 95-136

Section 5: Numerical Methods, Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 195-218

Study Of Tuberculosis Spread In Clinical Settings In Resource-Constrained Countries Using Computational Fluid Dynamics (Cfd), Adeel Khalid

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

Section 1: Bio-Medical/Bioengineering; pp. 3-10

Section 4: Energy Generation & Conversion, Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 137-194

Significance Of Mwcnt And Tio2 Nanofillers On Low-Density Polyethylene Thermal & Mechanical Properties: Applicability For Pipes Used In Water & Energy Systems, Trenicka Rolle, Ramana Pidaparti

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

Section 1: Bio-Medical/Bioengineering; pp. 18-23

Development Of A Rehabilitative Exoskeletal Arm, Daniel A. Garcia, Victor Soto, Yojans Lurbe, Melissa Morris, Sabri Tosunoglu

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

Section 1: Bio-Medical/Bioengineering; pp. 11-17

A Review Of Rehabilitation Strategies For Stroke Recovery, Daniel A. Garcia, Rodrigo Arrendondo, Melissa Morris, Sabri Tosunoglu

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

Section 1: Bio-Medical/Bioengineering; pp. 24-31

Section 6: Fluids Engineering, Asme Ectc Coordinating Committee

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

pp. 219-250

The Effect Of Stent Design On Hemodynamic Flow In Patient-Specific Diseased Carotid Bifurcation Arteries, Rodward L. Hewlin Jr, John P. Kizito

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

Section 1: Bio-Medical/Bioengineering; pp. 32-39

Modeling Ventilation And Perfusion Mismatch During Acute Lung Injury, Le Yang, Ramana Pidaparti, Huan Mo

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

Section 1: Bio-Medical/Bioengineering; pp. 40-44

Thermal Annealing Improves The Performance Of Cadmium Zinc Telluride (Czt) Semiconductor Material Used For Nuclear Radiation Detectors, Aaron L. Adams, Marcus D. Ashford, Aschalew Kassu, Mebougnal L. Drabo, Wing Chan, Stephen Egarievwe, Asja Radja, Ge Yang, Ralph B. James

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

Section 2: Materials; pp. 47-51

Formation Of Η And Ε Phases Of Intermetallic In Snag/Cu-Substrate Soldering System Under Structurally Constrained Condition, Ousama M. Abdelhadi, Leila Ladani

Early Career Technical Journal (ECTJ)

Proceedings of the ASME Early Career Technical Conference, November 4-5, 2011. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia

Section 2: Materials; pp. 52-56