Mechanical Engineering Commons^™

Benchmarking Of A Single-Cylinder Engine Toward The Development Of A Direct Fuel-Injection System, Michael J. Nienhuis

Masters Theses

In this study, the performance and efficiency of a single-cylinder gasoline, fourstroke cycle engine was benchmarked in support of the Formula SAE student project. The development of an engine test stand, instrumentation, data acquisition, and test plan is described in detail. Experimental results in the areas of engine performance and efficiency are discussed. Physical test data were used to refine a previous model of a single-cylinder, gasoline, direct-injection engine. Results from this effort are discussed and compared to those obtained in a preliminary study. The current work advances the development of more efficient power-train technologies for application in small displacement …

Adsorption Of Particles On Fluid-Liquid Interfaces, Bhavin Dalal

Dissertations

Particles floating on fluid-liquid interfaces are of considerable interest because of their importance in a range of physical applications and biological processes, e.g., self-- assembly of particles at fluid-fluid interfaces resulting in novel nano structured materials, stabilization of emulsions, formation of pollen and insect egg rafts, etc. The aim of this dissertation is to explore the mechanism by which particles are adsorbed at fluid-liquid interfaces. It is shown that the inertia of a particle plays an important role in its motion in the direction normal to a fluid-liquid interface, and in determining the particles adsorption trajectory and orientation in …

Design And Automated Operation Of A Condensation-Induced Depressurization System, Fen Du

Dissertations

Typical examples of the use of the vacuum environments in industry include vacuum coating, vacuum drying, vacuum packing, vacuum casting, vacuum heat treatment, vacuum cooling for food storage and leakage detection. Most of these applications require a comparatively small volume of vacuum environment. However, there are also many applications where enormous vacuum chambers are needed. For example, a large vacuum chamber is used to simulate the conditions of space.

This study investigates the design and the automated operation of a vacuum generation system based on the idea of the condensation-induced depressurization with prefilled condensable medium in a confined, adiabatic chamber. …

The Composition And Morphology Of Coal Ash Deposits Collected In An Oxy-Fuel, Pulverized Coal Reactor, Curtis K. Stimpson

Theses and Dissertations

Coal ash deposits were collected in a 160 kWth, down-fired oxy-coal reactor under staged and unstaged conditions for four different coals (PRB, Gatling, Illinois #6, and Mahoning). Concentration measurements of carbon, oxygen, sodium, magnesium, aluminum, silicon, phosphorus, sulfur, chlorine, potassium, calcium, titanium, chromium, manganese, iron, nickel, strontium, and barium were gathered from each deposit sample using scanning electron microscopy and energy dispersive spectroscopy (SEM-EDS). Backscattered electron micrographs for each deposit sample were analyzed to gather morphological data. Particle size and shape were studied for each deposit collected. The average particle sizes of the particles in upstream deposits were much larger …

Mechanical Properties And Mems Applications Of Carbon-Infiltrated Carbon Nanotube Forests, Walter C. Fazio

Theses and Dissertations

This work explores the use of carbon-infiltrated carbon nanotube (CI-CNT) forests as a material for fabricating compliant MEMS devices. The impacts of iron catalyst layer thickness and carbon infiltration time are examined. An iron layer of 7nm or 10nm with an infiltration time of 30 minutes produces CI-CNT best suited for compliant applications. Average maximum strains of 2% and 2.48% were observed for these parameters. The corresponding elastic moduli were 5.4 GPa and 4.1 GPa, respectively. A direct comparison of similar geometry suggested CI-CNT is 80% more flexible than single-crystal silicon. A torsional testing procedure provided an initial shear modulus …

Resonance Frequencies Of A Spherical Aluminum Shell Subject To Static Internal Pressure, Andrew A. Piacsek, Sami Abdul-Wahid, Robert Taylor

All Faculty Scholarship for the College of the Sciences

Measurements of the vibrational response of a spherical aluminum shell subject to changes in the interior pressure clearly demonstrate that resonance frequencies shift higher as the pressure is increased. The frequency shift appears to be smaller for longitudinal modes than for bending wave modes. The magnitude of frequency shift is comparable to analytical predictions made for thin cylindrical shells. Changes in the amplitudes of resonance peaks are also observed. A possible application of this result is a method for noninvasively monitoring pressure changes inside sealed containers, including intracranial pressure in humans.

No, Burnout, Flame Temperature, Emissivity, And Radiation Intensity From Oxycombustion Flames, Darrel Patrick Zeltner

Theses and Dissertations

This work produced the retrofit of an air-fired, 150 kW reactor for oxy-combustion which was then used in three oxy-combustion studies: strategic oxy-combustion design, oxy-combustion of petroleum coke, and air versus oxy-combustion radiative heat flux measurements. The oxy-combustion retrofit was accomplished using a system of mass flow controllers and automated pressure switches which allowed safe and convenient operation. The system was used successfully in the three studies reported here and was also used in an unrelated study. A study was completed where a novel high oxygen participation burner was investigated for performance while burning coal related to flame stability, NO, …

Agent-Based Modeling Of Emergency Building Evacuation, Vi Q. Ha

Master's Theses

Panic during emergency building evacuation can cause crowd stampede, resulting in serious injuries and casualties. Agent-based methods have been successfully employed to investigate the collective human behavior during emergency evacuation in cases where the configurational space is extremely simple - usually one rectangular room - but not in evacuations of multi-room or multi-floor buildings. This implies that the effect of the complexity of building architecture on the collective behavior of the agents during evacuation has not been fully investigated. Here, we employ a system of self-moving particles whose motion is governed by the social-force model to investigate the effect of …

Numerical Modeling Of Lifting Flows In The Presence Of A Free Surface, Leonardo R. Carmona Vasquez

LSU New Orleans Theses and Dissertations

This thesis work started as an attempt to create a computational tool to model hydrodynamics problems involving lifting flows. The method employed to solve the problem is potential flow theory.

Despite the fast evolution of computers and the latest developments in Navier-Stokes solvers, such as the Ranse methods; potential flow theory offers the possibility to create or use existing computational tools, which allow us modeling hydrodynamics problems in a simpler manner. Navier-Stokes solver can be very expensive from the computational point of view, and require a high level of expertise in order to achieve reliable models.

Based on the above, …

An Investigation Of Mist/Air Film Cooling With Application To Gas Turbine Airfoils, Lei Zhao

LSU New Orleans Theses and Dissertations

Film cooling is a cooling technique widely used in high-performance gas turbines

to protect turbine airfoils from being damaged by hot flue gases. Film injection holes are

placed in the body of the airfoil to allow coolant to pass from the internal cavity to the

external surface. The ejection of coolant gas results in a layer or “film” of coolant gas

flowing along the external surface of the airfoil.

In this study, a new cooling scheme, mist/air film cooling is proposed and

investigated through experiments. Small amount of tiny water droplets with an average

diameter about 7 μm (mist) is …

Correlation Of Shear Strength Between Longitudial And Transverse Specimens, Erasto A. Fernandez

LSU New Orleans Theses and Dissertations

In this thesis, new methods for shear strength are proposed and backed up through extensive experimentation, ABAQUS models and data analysis of Titanium welds of three different alloys. The results are compared with those obtained by using the procedure outlined by AWS B4 for calculating Shear Strength in the transverse and longitudinal directions; this equation is widely used by the American Welding Society (AWS) and all those in search of more efficient designs involving welding.

It is a well-documented issue that the equation provided by AWS yields a large discrepancy between the values for shear strength of longitudinal and transverse …

Single Inverted Pendulum System Controller: System Study And Comparison, Cheng Cheng

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science and Technology at Morehead State University in partial fulfillment of the requirements for the Degree of Master of Science by Cheng Cheng on May 15, 2012.

Rehabilitation And Exercise Machine, Judith M. Burnfield, Yu Shu, Thad W. Buster, Carl Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

An improved rehabilitation and exercise machine is provided which allows a person with physical limitations, disabilities or chronic conditions to use the machine in order to rehabilitate their muscles, improve joint flexibility, and enhance cardiovascular fitness.

A Method For Exploring Optimization Formulation Space In Conceptual Design, Shane Keawe Curtis

Theses and Dissertations

Formulation space exploration is a new strategy for multiobjective optimization that facilitates both divergent searching and convergent optimization during the early stages of design. The formulation space is the union of all variable and design objective spaces identified by the designer as being valid and pragmatic problem formulations. By extending a computational search into the formulation space, the solution to an optimization problem is no longer predefined by any single problem formulation, as it is with traditional optimization methods. Instead, a designer is free to change, modify, and update design objectives, variables, and constraints and explore design alternatives without requiring …

Advanced Design Optimization For Composite Structure: Stress Reduction, Weight Decrease And Manufacturing Cost Savings, Shayan Ahmadian

Master's Theses

An injection moldable chopped fiber composite actuator with detailed drawing and tolerances was designed within one year. A vendor was selected and a quote for injection molding tooling cost for production was obtained and the first prototype was built in addition of six months. The risks are identified and material characterization tests are proposed.

The objective of this project was redesigning an aluminum made actuator with a continuous fiber composite for weight saving purposes. After searching the literature and consulting with experts in the field it was concluded that manufacturing costs associated with continuous fiber composite are 3 times as …

Re-Configurable Putting Green, Matthew Ralphs

Undergraduate Honors Capstone Projects

This report discusses the design of a prototype transformable putting green that can be programmed to recreate the topography of any putting green. The goal of the design was to give a realistic putting experience with real topography in an indoor environment. This report discusses the design of a pair of 4’x4’ module prototypes; a commercial implementation of this design would utilize a number of modules to create putting greens on a more realistic scale (example 12’x32’). The design of a full size transformable putting green necessitates a topographical range of up to 30”. After initial concepts and preliminary designs …

College Of Engineering Senior Design Competition Spring 2012, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Senior Design Experience

Part of every UNLV engineering student’s academic experience, the Senior Design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs and prototypes a product in this required element of the curriculum. Working in teams, the senior design project encourages students to use everything learned in the engineering and computer design programs to create a practical, real world solution to an engineering challenge.

Beyond the classroom...

Because of the requirement to work in teams, students also build good communication skills, presentation skills and even business writing skills. They also have to source …

College Of Engineering Senior Design Competition Spring 2018, University Of Nevada, Las Vegas

Fred and Harriet Cox Senior Design Competition Projects

Part of every UNLV engineering student’s academic experience, the senior design project stimulates engineering innovation and entrepreneurship. Each student in their senior year chooses, plans, designs, and prototypes a product in this required element of the curriculum. A capstone to the student’s educational career, the senior design project encourages the student to use everything learned in the engineering program to create a practical, real world solution to an engineering challenge. The senior design competition helps focus the senior students in increasing the quality and potential for commercial application for their design projects. Judges from local industry evaluate the projects on …

An Investigation Of Fraxinus Americana Branch Sway Using A 3 Dimensional Motion Capture System, Anna T. Campiformio

Master's Theses

Abstract

Wind is a dominant abiotic factor that a tree experiences throughout its lifetime and can cause severe tree damage, resulting in risk of injury to humans, and economic and ecological losses. It is thought that trees develop structural properties and architectures that help withstand loading conditions by dissipating wind energy through damping mechanisms. The role of branch motion in reducing potential dangerous wind loads has been the focus of relatively few studies. Even fewer studies have examined tree sway response to natural wind loaded conditions. In this investigation, branch frequencies were calculated for three Fraxinus americana using a three-dimensional …

Analysis And Testing Of Heat Transfer Through Honeycomb Panels, Daniel D. Nguyen

Aerospace Engineering

This project attempts to simulate accurately the thermal conductivity of honeycomb panels in the normal direction. Due to the large empty space of the honeycomb core, the thermal radiation mode of heat transfer was modeled along with conduction. Using Newton’s Method to solve for a steady state model of heat moving through the honeycomb panel, the theoretical effective thermal conduction of the honeycomb panel was found, ranging from 1.03 to 1.07 Q/m/K for a heat input of 2.5 W to 11.8 W. An experimental model was designed to test the theoretical results, using a cold plate and a heat plate …