Distributed Vibration Sensing For Identification Of Loose Connectors In Coaxial Data Transmission Lines,
2026
Missouri University of Science and Technology
Distributed Vibration Sensing For Identification Of Loose Connectors In Coaxial Data Transmission Lines, Saidanvar Esanjonovich Valiev, Anthony C. Okafor, Jeremiah J. Rittenhouse, Jie Huang, Daniel S. Stutts
Mechanical and Aerospace Engineering Faculty Research & Creative Works
This study investigates the effect of vibration-induced loose connections on signal reflection (S11) for loose connection identification in aerospace coaxial cables using distributed sensing approach, which is effective in filtering the noise and identifying minor discontinuities. In this approach, a sliding gated window is applied to S11 signal, a fast Fourier transform is performed over the gated windows, cross-correlation is computed between the baseline and vibration-affected signals, and the standard deviation is mapped along the cable length. Sinewave signals from 9 kHz to 5 GHz were swept through cables with vibrating connectors under three conditions: fully tightened, loosened by 180°, …
Multiphysics Modeling Of Melt Pool Dynamics And Powder Bed Stability In Lpbf Of Inconel 718 For A Circular Cavity,
2026
Missouri University of Science and Technology
Multiphysics Modeling Of Melt Pool Dynamics And Powder Bed Stability In Lpbf Of Inconel 718 For A Circular Cavity, Nayan Pundhir, Oluwapelumi O. Adejumo, Kumbla Chandrashekhara, Joseph W. Newkirk, Heath Misak, Cesar Ortiz Rios
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Laser powder bed fusion (LPBF) is a metal additive manufacturing process in which a concentrated laser beam selectively melts successive powder layers to fabricate components. Final part quality is highly sensitive to process parameters such as hatch spacing, powder bed density, laser power, and scanning speed. In this study, a computational fluid dynamics model employing discrete element method has been developed in FLOW-3D to simulate LPBF of Inconel 718. The modeled powder bed incorporates particle size distribution data obtained from scanning electron microscopy and is evaluated for single-layer, single-track deposition over a circular cavity. The model captured melt pool dynamics …
Atomized Oxidative Polymerization As A 3d Printing Platform For Binder-Free, Bulk Conductive Polymer Architectures,
2026
Missouri University of Science and Technology
Atomized Oxidative Polymerization As A 3d Printing Platform For Binder-Free, Bulk Conductive Polymer Architectures, Tazdik Patwary Plateau, Hiep Pham, Jonghyun Park
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Translating the ultrahigh intrinsic conductivity of conjugated polymers into bulk 3D architectures remains a formidable challenge due to the fundamental dichotomy between rheological printability and electronic purity. Existing strategies necessitate a compromise: solution-processing requires insulating binders that degrade charge transport, while binder-free vapor-phase polymerization (VPP) is kinetically confined to surface-limited thin films by diffusion constraints. Here, we introduce atomized oxidative polymerization (AOP), a manufacturing paradigm that overcomes these kinetic barriers via active, layer-by-layer monomer atomization. This approach ensures stoichiometric reaction conditions throughout the printed volume, driving a structural transition toward highly conductive quinoid-dominant chains with enhanced π-π stacking. The resulting …
Performance Evaluation Of Thick Carbon Fiber-Reinforced Laminates Manufactured Using Six-Magnetron Microwave System,
2026
Missouri University of Science and Technology
Performance Evaluation Of Thick Carbon Fiber-Reinforced Laminates Manufactured Using Six-Magnetron Microwave System, Nayan Pundhir, Sourav Bolar, Kumbla Chandrashekhara, Kristen Donnell, Jim Lua, Kalyan Shrestha, Rui Li
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Microwave curing is a fast, energy-efficient, and a viable alternative to conventional thermal curing processes. It has been widely adopted for processing carbon fiber-reinforced polymer composites because the high electrical conductivity of carbon fibers enables strong microwave coupling. In this study, IM7/Cycom 5320-1 unidirectional prepreg has been used to fabricate 64-layer laminated composites. Symmetric cross-ply ([0°/90°]16S) and a quasi-isotropic ([45°/90°/−45°/0°]8S) layup have been investigated. A custom-built six-magnetron microwave applicator and an autoclave were employed to manufacture the composite panels. Degree of cure of the manufactured laminates was evaluated via differential scanning calorimetry. Interfacial bonding and porosity of the microwave-cured laminates …
Design, Construction, And Initial Testing Of A Oxy-Acetylene Testing Facility,
2026
Missouri University of Science and Technology
Design, Construction, And Initial Testing Of A Oxy-Acetylene Testing Facility, Blake Bowman, Davide Viganò
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Thermal Protection Systems (TPS) are critical for atmospheric re-entry and hypersonic flight vehicles, yet ground-based evaluation of TPS materials remains challenging due to the cost, complexity, and limited availability of large arc-jet and inductively coupled plasma (ICP) facilities. Oxy-acetylene testing provides a low-cost and accessible alternative for preliminary material screening, sensor development, and fundamental studies of material response under high heat-flux conditions. This paper presents the design, construction, and initial validation of the High-Enthalpy Acetylene Testing (HEAT) facility at Missouri University of Science and Technology. The facility incorporates a modular experimental architecture, independently controlled oxygen and acetylene mass-flow systems, and …
Tomo-Piv Study Of A Parallel Two-Dimensional Jet In Supersonic Flow,
2026
Missouri University of Science and Technology
Tomo-Piv Study Of A Parallel Two-Dimensional Jet In Supersonic Flow, Josiah Mcdermott, Connor Bell, Davide Vigano
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Stabilizing combustion in supersonic flows is a formidable challenge due to the small time scales afforded for air-fuel mixing. Numerous studies in this area have demonstrated the potential of strut-style platforms for fuel injection and mixing enhancement, which remains an active area of research. In the Aerodynamics Research Laboratory at Missouri S&T, a strut-style injector system has recently been installed. In this study, we characterize the flow structures behind this platform in a range of injection pressures and corresponding mass flux ratios. The wake generated by a strut and injection plume, even absent combustion or mixing enhancement geometry, has an …
2-Point Focused Laser Differential Interferometry Measurements Of A Parallel Jet In Supersonic Flow,
2026
Missouri University of Science and Technology
2-Point Focused Laser Differential Interferometry Measurements Of A Parallel Jet In Supersonic Flow, Joshua Gary, Joseph Villarreal, Davide Vigano
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Turbulence in compressible flows plays a central role in applications such as air-fuel mixing in supersonic combustors and is significantly more complex than incompressible turbulence due to the presence of fluctuating thermodynamic quantities. As such, models like the Strong Reynolds Analogy (SRA) are used to relate these quantities. However, SRA validity has been examined primarily in boundary-layer flows. In this work, a newly developed Two-Point Focused Laser Differential Interferometry (2-FLDI) system is implemented in a two-dimensional parallel supersonic jet. The diagnostic is described in detail, including optical alignment procedures, calibration methods, and data analysis techniques. Measurements acquired at multiple streamwise …
Corrigendum To “3d Semi-Analytical Thermo-Elasto-Plastic Model For Additive Manufacturing”(Additive Manufacturing, (2026), 127, C, (105308), (S2214860426002344), 10.1016/J.Addma.2026.105308),
2026
Missouri University of Science and Technology
Corrigendum To “3d Semi-Analytical Thermo-Elasto-Plastic Model For Additive Manufacturing”(Additive Manufacturing, (2026), 127, C, (105308), (S2214860426002344), 10.1016/J.Addma.2026.105308), Tao Liu, Ming C. Leu, Edward C. Kinzel, Chinedum Okwudire
Mechanical and Aerospace Engineering Faculty Research & Creative Works
The author regret about the correction in the Equation B(1) in original article. The corrected version of the Equation B(1) is given below,(1.1)∂uxxx,ξ∂x=116πμ1−ν4ν−1x−ξxR3−3x−ξx3R5−8ν−5x−ξxR13+34ν−3x−ξx3R15−18x−ξxzξzR15+30x−ξx3zξzR17−12ν−12ν−1x−ξxR1R1+z+ξz2+4ν−12ν−1x−ξx3R13R1+z+ξz2+8ν−12ν−1x−ξx3R12R1+z+ξz3 The authors would like to apologise for any inconvenience caused. DOI of original article: < 10.1016/j.addma.2026.105308>
Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy,
2026
Missouri University of Science and Technology
Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely
Materials Science and Engineering Faculty Research & Creative Works
All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …
Overcoming Resolution Vs. Throughput Trade-Offs In Ceramic Material Extrusion Additive Manufacturing Via Viscoelastic Filament Stretching,
2026
Missouri University of Science and Technology
Overcoming Resolution Vs. Throughput Trade-Offs In Ceramic Material Extrusion Additive Manufacturing Via Viscoelastic Filament Stretching, Abid H. Rafi, David W. Lipke, Jeremy L. Watts, Gregory E. Hilmas, Ming C. Leu
Materials Science and Engineering Faculty Research & Creative Works
Fabricating large, monolithic ceramic parts using material-extrusion additive manufacturing remains challenging due to difficulty maintaining uniform moisture content during printing, which can lead to drying-induced defects such as warping and cracking, especially as part size and print time increase. Fabricated parts have trade-offs among print resolution, high throughput, and structural fidelity. Our study has shown that increasing the ratio of nozzle traverse speed vs. material extrusion speed increases filament stretching in viscoelastic ceramic paste, helping to overcome the trade-offs between resolution and throughput. Using aqueous ZrB2–SiC (70/30 vol.%) as a representative ultra-high temperature ceramic paste, rheological characterisation revealed viscoelastic yield-stress …
Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size,
2026
Missouri University of Science and Technology
Modeling Of Transformation Temperatures In Cast Martensitic Stainless Steels-Ca6nm: Effects Of Composition, Heating Rate, And Grain Size, Ugochukwu Agbedo, Mario Buchely, Laura Bartlett, Caelan Kennedy
Materials Science and Engineering Faculty Research & Creative Works
Accurate prediction of the critical transformation temperatures Ac1 and Ac3 is one of the essential factors in the heat treatment of CA6NM cast martensitic stainless steel. In this study, the influence of alloy composition, heating rate, and prior austenite grain size on the critical temperatures was quantified using dilatometric measurements and statistical modeling. Six heat treatment conditions produced prior austenite grain sizes ranging from ~75 to 247 µm. Experimental results showed that grain size variations produced only minor changes in Ac1 and Ac3, indicating a weak dependence of transformation temperatures on prior austenite grain size within the investigated range. In …
Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels,
2026
Missouri University of Science and Technology
Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar
Materials Science and Engineering Faculty Research & Creative Works
High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …
Effect Of Complex Alloying Elements On Oxide Scale Formation And Water-Jet Descaling Performance On Continuously Cast Low-Carbon Steels,
2026
Missouri University of Science and Technology
Effect Of Complex Alloying Elements On Oxide Scale Formation And Water-Jet Descaling Performance On Continuously Cast Low-Carbon Steels, Tochukwu P. Ojiako, Tsvetkov Dmitry, Mario Buchely, Haiming Wen, Simon N. Lekakh, Ronald J. O'Malley
Materials Science and Engineering Faculty Research & Creative Works
The formation and evolution of oxide scale in contact with mold flux during continuous casting, subsequent reheating, and hydraulic descaling are strongly governed by steel chemistry. To elucidate the effect of complex alloying elements (Si, Mn, and Cr), two industrially produced continuously cast low-carbon steel grades for manufacturing stamped parts (a base and alloyed steel grade) were investigated. The objective was to determine how alloying elements influence oxidation behavior, scale morphology, interfacial adhesion, and water-jet descaling efficiency. Continuously cast slab specimens were subjected to controlled thermal and atmospheric oxidation cycles simulating multistage industrial practice. Three initial surface conditions (industrial as-cast, …
Simulated Lunar Gravity Testing Of A Magnetic And Electrostatic System For Beneficiating Lunar Regolith,
2026
Missouri University of Science and Technology
Simulated Lunar Gravity Testing Of A Magnetic And Electrostatic System For Beneficiating Lunar Regolith, Blake A. Coffman, Gabriel Porter, Lindsay Manteufel, Mitchell Cottrell, Jeffrey D. Smith, David J. Bayless, William Shonberg, Frank D. Han, Fateme Rezaei, Kirby Runyon
Materials Science and Engineering Faculty Research & Creative Works
We present the design and testing of a lunar regolith beneficiation device that utilizes magnetic and electrostatic separation methods to concentrate desired minerals by removing unwanted material, such as the mineral anorthite, from bulk lunar regolith. The beneficiated materials would have value for downstream in-situ resource utilization (ISRU) processes such as metal extraction, oxygen extraction, and metal oxide additive manufacturing processes. The apparatus uses a dual-strength magnet system with N52 and N42 neodymium magnets to separate particles by magnetic susceptibility. The electrostatic separation system, which acts like a sieve, sorts the regolith simulant by particle size using a single-phase 50% …
The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing,
2026
Missouri University of Science and Technology
The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley
Materials Science and Engineering Faculty Research & Creative Works
Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …
Towards Supporting Real-Time Estimation Of Vehicle Fuel Consumption And Co2 Emissions In Smart City Applications,
2026
Saudi Electronic University
Towards Supporting Real-Time Estimation Of Vehicle Fuel Consumption And Co2 Emissions In Smart City Applications, Abrar Alali, Stephan Olariu
Computer Science Faculty Publications
This paper evaluates a simplified physics-based energy demand model designed to estimate vehicle fuel consumption and CO₂ emissions—a critical tool for sustainable transportation planning and smart city applications. Unlike data-driven regression models that lack generalizability for user-defined conditions or complex physics-based approaches that rely on extensive, often proprietary data, the simplified model is distinguished by its minimal parameter requirements, depending primarily on a single, overarching powertrain efficiency value. A key contribution is the comprehensive empirical evaluation of the simplified model against official Environmental Protection Agency (EPA) test data across multiple driving cycles and vehicle types, providing a rigorous validation previously …
Analytical Study Of Transient Mixed Convective Radiative Jeffrey Fluid Flow With Diffusion–Thermo And Chemical Reaction,
2026
Department of Mathematics, Muthurangam Government Arts College(Affiliated to Thiruvalluvar University), Vellore-632002, Tamil Nadu, India.
Analytical Study Of Transient Mixed Convective Radiative Jeffrey Fluid Flow With Diffusion–Thermo And Chemical Reaction, V. Sathiya, R. Vijayaragavan, B. Rushi Kumar
Mansoura Engineering Journal
This research examines the behavior of unsteady mixed convective radiative Jeffrey fluid flow over a permeable moving plate with a diffusion thermo effect. The study incorporates multiple factors, including aligned magnetic fields, heat generation, radiation, and chemical reactions. The behavior of Jeffrey fluid under these combined conditions is particularly relevant to the design of efficient heat exchangers, MHD generators, and cooling systems for electronic components. A regular perturbation technique was employed to solve the governing equations, yielding distributions for velocity, temperature, and species concentration. These solutions enabled the derivation of expressions for skin friction, Nusselt number, and Sherwood number. Through …
Computational Modeling Of Bubble Dispersion In Alginate Hydrogel Foams For Radiologically Equivalent Biomedical Phantoms,
2026
University Central of Florida
Computational Modeling Of Bubble Dispersion In Alginate Hydrogel Foams For Radiologically Equivalent Biomedical Phantoms, Godson N. Brako
Graduate Studies Theses and Dissertations 2026
The foaming of hydrogels presents a promising strategy for tailoring mechanical and radiological properties to replicate biological soft tissues for biomedical phantoms. Achieving uniform and predictable void fraction distributions in alginate hydrogel foams remains a challenge due to the complex interplay between bubble dynamics, matrix rheology, and interfacial forces during the pre-gelation aeration stage. This thesis develops a Computational Fluid Dynamics framework using the transient Eulerian two-fluid approach to predict void fraction distribution in alginate hydrogel precursor solutions aerated by air injection through a bottom nozzle. The objective is to use the framework for design of the foaming system to …
Viscoelastic Behavior Of Magnetically Filled Pdms Elastomers: Influence Of Filler Loading And Particle Type,
2026
Georgia Southern University
Viscoelastic Behavior Of Magnetically Filled Pdms Elastomers: Influence Of Filler Loading And Particle Type, Madison Procyk
College of Graduate Studies: Theses & Dissertations
Magnetorheological elastomers (MREs) offer a promising pathway for soft, magnetically actuated drug‑delivery systems, yet material‑selection guidelines remain unclear due to limited comparative data across particle chemistries, size scales, and concentrations. This study systematically evaluates how magnetic filler type (carbonyl iron and magnetite) and particle size (micro vs. nano), at two weight percentages – 40 wt% and 50 wt% – in Sylgard 184 PDMS influence the viscoelastic behavior of MREs intended for compliant biomedical actuation. Eight particle formulations were prepared through sieving, controlled mixing, vacuum degassing, and isotropic curing, producing nineteen total specimens (16 with filler particles and 3 without). Dynamic …
A Real-Time Autonomous Mobile Robotic System For Crack Detection And 3d Laser Profiling In Construction Using Two-Stage Deep Learning,
2026
Georgia Southern University
A Real-Time Autonomous Mobile Robotic System For Crack Detection And 3d Laser Profiling In Construction Using Two-Stage Deep Learning, Emmanuella Ogun
College of Graduate Studies: Theses & Dissertations
This thesis presents an autonomous mobile robotic system that integrates real-time visual crack detection with laser-based three-dimensional profiling for building inspection. The system coordinates SLAM-based navigation, deep learning perception, and manipulator-guided measurement within a unified ROS 2 framework, enabling scan-on-demand workflows where laser profiling occurs selectively at visually detected defect locations. The detection pipeline employs a two-stage architecture combining U-Net semantic segmentation with Pix2Pix residual refinement, achieving 73.9% mean intersection-over-union and 76.4% F1-score on the CrackSeg9k benchmark while maintaining 16 frames-per-second real-time throughput. Real-world validation demonstrated 95% detection success on 80 campus images under challenging conditions. The profiling subsystem utilizes …
