Mechanical Engineering Commons^™

Pseudo-Boiling Of Supercritical Co2 In A Parallel-Flow Microchannel And A Micro-Jets Impingement Device And Single-Phase And Two-Phase Heat Transfer Of Subcritical Co2 Jets, Pranzal Ahmed

Graduate Studies Theses and Dissertations 2026

Carbon dioxide (CO2) is gaining attention as a low-toxicity, zero-ozone-depletion refrigerant with a global warming potential of 1, making it an attractive alternative to synthetic HFCs/HFOs. Near its critical point, CO2's thermophysical properties change sharply with small shifts in temperature and pressure — a behavior that can be exploited to enhance heat transfer in trans-critical power cycles and electronics cooling. This dissertation experimentally investigates heat transfer during the pseudo-boiling of supercritical CO2 in a parallel-flow microchannel and a micro-jet impingement device, alongside CO2 flow boiling and single-phase water heat transfer in micro-jet impingement. Using microfluidic devices instrumented with embedded resistance …

Machine Learning Modeling Of In-Situ Effective Thermal Conductivities And Ablation Behaviors Of Ceramic Matrix Composites Under Hydrogen Combustion Environments For Gas Turbine Engines, Jayanta Bhusan Deb

Graduate Studies Theses and Dissertations 2026

Through the integration of experimental characterization, machine learning, deep learning, numerical modeling, and physics-informed artificial intelligence, this dissertation explores the thermal performance of polymer-derived ceramic matrix composites (CMCs) for hydrogen combustion environments. The polymer infiltration and pyrolysis (PIP) process was used to create Yttria-stabilized zirconia (YSZ)-fiber-reinforced ceramic matrix composites, which were then experimentally assessed under hydrogen torch and hydrogen combustion conditions typical of next-generation gas turbine and aerospace propulsion systems. Front- and back-surface temperature measurements were used to continually monitor thermal reactions, and post-test microstructural characterization and numerical simulations were carried out to evaluate material integrity and heat-transfer behavior. To …

Performance Analysis Of Labyrinth And Hybrid Seals For Supercritical Co₂ Turbomachinery Applications, Ghanshyam Sarobar Mandal

Graduate Studies Theses and Dissertations 2026

Leaks account for large losses in turbomachinery systems, which has led to research on sealing technologies. The work presented studies the effect of a hybrid seal combining conventional labyrinth geometry and honeycomb structure by simulating supercritical carbon dioxide (sCO₂) flow through this geometry. The CFD solver compares effects such as changes in mass flow rate, formation of vortices, pressure profile, and seal performance as geometry angles of labyrinth teeth and honeycomb walls change at conditions normally found at higher pressures in these seals. Honeycomb walls were placed on the stator, ranging from 125°< θc< 55°. Labyrinth teeth were placed on the rotor at the same degrees. Honeycomb cell diameters were also varied, creating more resistance and turbulence within the flow. It was discovered that the honeycomb angle created stronger effects on vortices and boundary layer formation, while the labyrinth angle mainly affected the throttling of flow and loss generation. Combining all three angles created a relationship dictating the seal leakage. Dimensions of seals were based on gas turbine seals with changes to meet sCO₂ conditions. ANSYS was used to simulate static and rotating conditions until convergence on a specific geometry

Experimental Demonstration Of A Laboratory Scale Packed Bed Reactor For Thermochemical Energy Storage Using Embedded Heating Elements, Zachary Monem

Graduate Studies Theses and Dissertations 2026

Thermochemical energy storage (TCES) is an emerging technology that is being studied as a carbon-neutral renewable alternative to conventional methods of large-scale power generation, such as the utilization of fossil fuels. TCES makes use of thermochemical materials to store and discharge energy in two-step reversible chemical reactions. Among the most promising TCES materials are metal oxides, which possess significantly higher energy storage densities compared to other TCES materials; consequently, thermochemical reactors are used to store and discharge large amounts of energy during reduction-oxidation cycles using metal oxide materials. The current work focuses on the design and experimental demonstration of a …

Experimental And Computational Characterization Of A Rotorcraft-Tiltrotor Model Using Morphing Wings For Whirl Flutter Instability, Darrell Nieves Lugo

Graduate Studies Theses and Dissertations 2026

Tiltrotor rotorcraft configurations combine the capabilities of vertical and forward flight, offering a crucial and advantageous design for maximizing the operational flight envelope. This versatility enables broad adaptability across numerous designs and platforms, including unmanned aerial vehicles (UAVs), micro-air vehicles (MAVs), and vertical take-off and landing (VTOLs) aircraft. However, propeller-based aircraft are susceptible to an aeroelastic instability at high flight speeds known as whirl flutter. This instability phenomena is a crucial research task and problem to investigate, as with advances in manufacturing and vehicle designs, these can yield new rotorcraft formats capable of advancing the flight envelopes at higher cruise …

Two-Phase Transcritical Carbon Dioxide Flow At The Microscale For Thermal Management Applications, Soroush Niazi

Graduate Studies Theses and Dissertations 2026

High-power electronic and power-conversion devices now generate heat fluxes that exceed what conventional air- and single-phase-liquid cooling can dissipate, motivating the search for more capable coolants and cooling mechanisms. Carbon dioxide is an attractive candidate for this role: it is inexpensive, non-toxic, and environmentally friendly, and near its critical point its thermophysical properties change rapidly, which raises the heat-transfer coefficient. In addition, a large pressure drop produces strong cooling through the Joule–Thomson effect and phase change, so that the throttling element itself becomes a source of cooling. This dissertation studies the throttling, phase change, and choking of high-pressure carbon dioxide …

On Performance And Applications Of A Liquid Fueled Pulsed Flame Jet Igniter, Gerardo A. Rodriguez

Graduate Studies Theses and Dissertations 2026

As global demands for supersonic and hypersonic flight heighten, high-speed air breathing propulsion technologies stand out as a worthwhile direction to overcome many of the limitations that turbomachinery-based engines face at supersonic speeds. Air breathing propulsion concepts are attractive for their geometrical simplicity, using supersonic incoming air to provide compression. Scramjet flight vehicles operate within the hypersonic flight regime and have been a global research topic, especially in the 21st century, for defense and combined cycle engine architectures. As scramjet technology continues maturing towards widespread use, efforts have converged on liquid hydrocarbon fuels for storage, range, and operational benefits. Flight …

Study On Fracture Toughness Under Different Modes Through Continuum Damage Mechanics Based Fracture Locus, Yeting Sun

Graduate Studies Theses and Dissertations 2026

Traditional elastic-plastic fracture mechanics (EPFM) relies on crack-tip analysis, whereas continuum damage mechanics (CDM) is typically calibrated from uncracked bodies. This dissertation aims to bridge the gap between these two fundamental branches by explicitly linking fracture toughness with ductile damage models. Based on the assumptions regarding Mode I crack deformation, analytical solutions are derived to establish a novel relationship among Mode I fracture toughness, CDM-based ductile fracture strain, and material strain hardening capability. This theoretical framework is subsequently extended to encompass Mode II and Mode III loading conditions. To validate the proposed relationships, finite element (FE) models are developed in …

Advanced Ysz/Si(B)Cn And Bnnt/Si(B)Cn Ceramics Matrix Composites For Extreme Environments In Hydrogen Combustion, Yiting Wang

Graduate Studies Theses and Dissertations 2026

The growing demand for carbon-neutral energy conversion has accelerated the development of hydrogen-fueled gas turbine systems, which operate at significantly higher temperatures and more chemically aggressive environments than conventional natural gas turbines. To meet these stringent requirements, ceramic matrix composite (CMC) materials consisting of yttria-stabilized zirconia (YSZ) fiber reinforced Si(B)CN ceramic matrix were developed. To further enhance in-plane heat dissipation, thermal stability, thermal shock resistance, and thermal cycling performance, a Si(B)CN/Boron Nitride Nanotubes (BNNT) nanocomposite coating was incorporated onto the YSZ/Si(B)CN composites. Microstructural characterization confirmed the formation of a continuous Si(B)CN ceramic matrix reinforced with uniformly distributed BNNTs. The resulting …

Turbine Exhaust Cylinder And Manifold Wake Interactions At High Swirl Angle, Christian A. Anzalotta

Graduate Studies Theses and Dissertations 2026

A commonly observed flow interaction in industrial gas turbine (IGT) exhaust diffuser configurations is investigated, where upstream structural wakes interact with downstream airfoil-like components, potentially leading to unsteady loading. To better understand the mechanisms contributing to this behavior, a scale-model is designed. Dynamic similarity is achieved by matching the Strouhal number (St) of the vortex shedding from the strut. A bell-mouth followed by a swirler is installed in front of the strut to mimic the flow angles at the inlet section of the turbine exhaust. Experiments are conducted for three swirl angles, namely, 30°, 45°, and 60°. Power spectra computed …

The Dynamics Of Near-Limit Detonation Waves For Hypersonic Propulsion, Liliana Berson

Graduate Studies Theses and Dissertations 2026

The usage of detonation waves in hypersonic propulsion engines has seen substantial advancement in recent decades. The near-limit transition and failure process are key in these applications controlling the operability regime. The common cellular propagation of detonation waves fails in the near limit leading eventually to a singular transverse shock instability. The local dynamics of the wave causing this transition and the details of this singular instability remain a challenging question. These dynamics are examined in a fully automated detonation experiment using ultra-high-speed diagnostics and statistical analysis. Hydrocarbon fuel–oxidizer mixtures with nitrogen dilution are used to explore transition behavior over …

An Algorithmic Framework For Polyhedral Gravity Modeling And Trajectory Propagation Near Small Bodies, Micah S. Boudreau

Graduate Studies Theses and Dissertations 2026

Near-Earth asteroids (NEAs) and other irregular celestial bodies have become increasingly significant targets for scientific investigation and space mission development due to their relevance to resource utilization, origins-of-life studies, planetary defense, and understanding of early solar system formation. As launch costs continue to decline, missions such as NASA’s NEAR Shoemaker, OSIRIS-REx and JAXA’s Hayabusa series demonstrate the expanding feasibility of detailed small body exploration. Despite this growing interest, most standard astrodynamics tools are not designed to model the complex, highly irregular gravitational fields that are a signature of small bodies. Such limitations pose challenges for trajectory design, navigation, and control …

Detonability Limits Of Liquid Fuel Cloud, Khaoula Chougag

Graduate Studies Theses and Dissertations 2026

Detonation-based propulsion systems are of significant interest owing to their high thermodynamic efficiency, rapid energy release, and favorable entropy production relative to deflagration-based systems. Liquid fuels offer practical advantages in storage and volumetric energy density, making them attractive candidates for next-generation detonation engines. This dissertation investigates the detonability characteristics of liquid hydrocarbon fuel clouds through three interconnected studies conducted in a turbulent shock-tube environment using high-speed imaging and pressure diagnostics. The first study maps the detonability limits of monodisperse n-dodecane clouds by systematically varying droplet diameter (5-50 μm) and O₂/N₂ oxidizer composition at equivalence ratios spanning ϕ = 0.8-2.0. Results …

Enhanced Atomization And Combustion In Subsonic Ljic Systems Using Ultrasonically Driven Solid Obstructions, Daniel Sebastian Cruz

Graduate Studies Theses and Dissertations 2026

The liquid fueling methods used in aircraft propulsion have undergone extensive optimization, with Liquid Jets in Crossflow (LJIC) emerging as a simple yet effective injection scheme. LJIC enables sufficient fuel mass flow rates and penetration for high-speed operation, however fuel trajectory and droplet size remain highly sensitive to crossflow conditions. As a result, wide flight envelopes introduce variability in atomization, leading to unsteady combustion performance. Recent work has incorporated a pintile, a solid obstruction placed in the path of the fuel jet, to redistribute momentum and reduce trajectory variability across varying flow conditions. While this approach improves trajectory uniformity, it …

A Framework For Optimizing Creep Model Parameters From Conventional And Accelerated Creep Tests, William D. Day

Graduate Studies Theses and Dissertations 2026

The demand for efficiency in power generation and propulsion requires higher firing temperatures and reduced cooling air consumption which raises metal temperatures. This makes simplistic creep evaluations, such as Larson-Miller and Orr-Sherby-Dorn parameters, inadequate. Finite element analysis (FEA) must simulate primary and secondary creep, predict failure, and provide design guidance. Gas turbine components, expected to last over 100,000 hours, often require extrapolation of limited test data for new materials. It is essential that robust creep simulations be developed efficiently, accurately, and effectively use limited test data.

This dissertation describes an optimized framework for efficient creep testing and rapid construction of …

Cylinder Wake Stability Effects Of Passive Forebody Modification And Active Harmonic Actuation, Matt Duran

Graduate Studies Theses and Dissertations 2026

This dissertation investigates the manipulation of global and three-dimensional instabilities in the wake of a circular cylinder through two separate flow control methods. This study first focuses on the influence of attached leading edge forebodies as a form of passive flow control designed to introduce upstream streamline curvature, where the curvature takes the form of a concave and convex case. We demonstrate that for both cases this induced curvature significantly modifies the primary instability, which suppresses periodic vortex shedding (Von Kármán vortex street). We found an increase in critical Reynolds number of 56.6 and 60.1 for the concave and convex …

Processing, Characterization And Performance Of Ceramic Liners For Hydrogen Gas Turbine Engines, Fahim Faysal

Graduate Studies Theses and Dissertations 2026

Advanced ceramics and ceramic matrix composites (CMCs) are known for their endurance at high temperatures. This study investigated the fabrication and testing of two material systems: silicon carbide nitride (SiCN) reinforced with yttria-stabilized zirconia (YSZ) fiber manufactured through polymer infiltration and pyrolysis (PIP), and 3D-printed alumina (Al₂O₃) ceramics. The CMC thermal stability at high temperatures was explored through a hydrogen torch test. The CMC surface could withstand a temperature of 1,400°C for 10 minutes during the torch test. Furthermore, the internal surface of a hydrogen combustion chamber was coated with CMC to assess its applicability as a protective barrier against …

The Development Of An Experimental Chemical Reactor Network Facility For Power Generation And Aviation Gas Turbines, Kesly Lubin

Graduate Studies Theses and Dissertations 2026

Gas turbines are the backbone of power generation globally; however, they are also one of the largest contributors to greenhouse gases and harmful emissions. Advanced combustion strategies, when applied to energy generation, can offer increased optimization of the combustion process with more complete and efficient combustion. With global efforts to reduce NOx formation in energy generation, combustion staging strategies like Rich Quench Lean (RQL), Lean-Premixed (LPM), and Exhaust Gas Recirculation (EGR) have gained more attention in research. The major challenge that exists in the research sector is the ability to evaluate and further develop these techniques at a fundamental level. …

Characterization And Experimental Study Of Ammonia-Hydrogen Flames Inside A Toroidal Jet-Stirred Reactor At Atmospheric Conditions, Oli Marquez Valenzuela

Graduate Studies Theses and Dissertations 2026

Due to rising concerns about global surface temperatures and carbon emissions, there has been an increased interest in studying alternative fuels. Ammonia and hydrogen are fuels with the potential to replace general biofuels, hydrocarbons, and sustainable aviation fuels, as they do not contain any carbon, eliminating carbon emissions. However, they are both difficult to work with. Hydrogen has great combustion characteristics such as low ignition energy, high flame speed and lower heating value. However, it is volatile and difficult to store, requiring it to be compressed to high pressure or cooled to incredibly low temperatures. Ammonia can be used as …

Chemical Kinetic Experiments Of Monomethyl Hydrazine Combustion Products At High Pressures And High Temperatures In A Shock Tube, Cooper Q. Mills

Graduate Studies Theses and Dissertations 2026

This study presents experimental shock tube laser absorption spectroscopy data to validate high-pressure and high-temperature chemical kinetic mechanisms for mixtures of H₂/air, NH₃/air, and H₂/CO/NO₂/air diluted in argon (95-98%) at high pressures (5, 10, 25 bar) and high temperatures (1000 to 2150 K). The mixtures were at equivalence ratios of 0.5, 1.0, and 1.5 to cover the range of possible conditions experienced throughout practical combustors. Laser absorption spectroscopy data was measured for NH₃, H₂O, CO, and NO using a novel multi-species setup. Chemical kinetic mechanisms contain the fundamental …