Mechanical Engineering Commons^™

Constitutive Modeling Of Glassy Memory Polymers, Mahesh Khanolkar

Dissertations

The aim of this research is to develop constitutive models for non-linear materials. Here, issues related for developing constitutive model for glassy shape memory polymers are addressed in detail. Shape memory polymers are novel material that can be easily formed into complex shapes, retaining memory of their original shape even after undergoing large deformations. The temporary shape is stable and return to the original shape is triggered by a suitable mechanism such heating the polymer above a transition temperature. Glassy shape memory polymers are called glassy because the temporary shape is fixed by the formation of a glassy solid, while …

Transport Mechanisms And Modeling Of Riser Reactor, Dawei Wang

Dissertations

Riser reactors are extensively employed in various industrial applications. In a riser reactor, the hydrodynamics is closely interacted with kinetic reactions. Common models for the performance prediction of riser reactors overlook this vital coupling effect, which not only miss the important reaction characteristics in the dense-phase transport regime of riser reactors but also misinterpret the kinetic properties via ad hoc adjustments. It is noted that the modeling of hydrodynamics in riser flows has major flaws in its predictability of phase transport in both dense-phase and accelerating regimes where most reactions occur. In addition, with the spray feeding of reactants at …

Stochastic And Deterministic Dynamics Investigation Of The Microstructure Of Granular Materials, Vishagan Ratnaswamy

Theses

Granular materials are ubiquitous in one's daily life. They can be found in the cereal you eat, the sugar you put in your coffee or the sand you walk on in the beach. The study of granular materials has a rich history dating back to the 17th century where Kepler studied the packing of particles. The compaction of granular materials is a problem that is studied by using theory, experiments and simulations. While these studies have yielded some important results, there still are many details about the mechanisms of granular compaction that are unknown.

In this thesis, the density relaxation …

Application Of Structured Light Imaging For High Resolution Mapping Of Underwater Archaeological Sites, Chris Roman, Gabrielle Inglis, James Rutter

Graduate School of Oceanography Faculty Publications

This paper presents results from recent work using structured light laser profile imaging to create high resolution bathymetric maps of underwater archaeological sites. Documenting the texture and structure of submerged sites is a difficult task and many applicable acoustic and photographic mapping techniques have recently emerged. This effort was completed to evaluate laser profile imaging in comparison to stereo imaging and high frequency multibeam mapping. A ROV mounted camera and inclined 532 nm sheet laser were used to create profiles of the bottom that were then merged into maps using platform navigation data. These initial results show very promising resolution …

Optimization And Correlation Of The Penn State Model Of Friction Stir Welding To Experimental Welds In 304l Stainless Steel, Devin Donaldson Furse

Theses and Dissertations

A numerical model of friction stir welding developed by T. DebRoy, R. Nandan, and others has been optimized to fit experimental data of eleven welds of 304L stainless steel at various weld feed rates and spindle speeds. Optimization was used to determine the values of five difficult-to-measure model parameters. The optimal parameter values were then correlated to the weld machine inputs. The mechanical efficiency and the coefficient of friction were not correlated with feed rate, spindle speed, or axial pressure. Tool slip was positively correlated with feed rate, negatively correlated with spindle speed, and not correlated with axial pressure. The …

Design And Analysis Of A Compliant Mechanism Spinal Implant, Eric M. Stratton

Theses and Dissertations

This thesis introduces and presents the modeling of a novel compliant spinal implant designed to reduce back pain and restore function to degenerate spinal disc tissues as well as provide a mechanical environment conducive to healing the tissues. The initial objectives for this device development and the focus of this work are modeling and validation of the force-deflection relationships and stress analysis. Modeling was done using the pseudo-rigid-body model to create a 3 degree of freedom mechanism for flexion-extension (forward-backward bending) and a 5 degree of freedom mechanism for lateral bending (side-to-side). These models were analyzed using the principle of …

Uniaxially-Driven Controlled Biaxial Testing Fixture, Fadi K. Abu-Farha, Marwan K. Khraisheh

Mechanical Engineering Faculty Patents

A uniaxially-driven controlled biaxial testing fixture includes a base, a first coupler mounted to the base, and a load input drive rack mounted for linear movement with respect to the base. A second coupler and a first specimen grip are both mounted to the load input drive rack. Second, third and fourth specimen grips are also mounted for linear movement with respect to the base. First, second and third drive mechanisms connect the load input drive rack to the second, third and fourth specimen grips. Together the four specimen grips are oriented to provide biaxial application of force to a …

A One-Dimensional Finite-Difference Solver For Fully-Developed Pipe And Channel Flows, Doug F. Hunsaker

Utah Space Grant Consortium

An algorithm is developed to solve the fundamental flow cases of fully-developed turbulent flow in a pipe and in a channel. The algorithm uses second-order finite-difference approximations for nonuniform grid spacing and is developed in such a way as to easily facilitate the implementation of several two-equation, Reynolds-Averaged-Navier-Stokes turbulence models. Results are included for the Wilcox 1998 k-ω model.

High Strength And Light-Weight Materials Inspired By The Exoskeleton Of Arthropods, Anette M. Karlsson

Mechanical Engineering Faculty Publications

This work investigates the multiscaled structure and the constitutive behavior of the exoskeleton of arthropods (Japanese beetle) along with the response of biomimicked structures. Image analysis (SEM and TEM) revealed three load-bearing regions comprised of chitin-protein fiber layers orientated parallel to the cuticle surface. The chitin fibers in the exocuticle and mesocuticle are organized in a helicoidal structure (layers stacked with a small rotational angle relative to their adjacent layers). The endocuticle has a distinct pseudo-orthogonal pattern, characterized by a thin transitional helicoidal region inserted between two orthogonal layers. Idealized mechanics based models showed that the pseudo-orthogonal structure redistributes the …

Simulation Of A Tubular Solid Oxide Fuel Cell Stack Operating On Biomass Syngas Using Aspen Plus, Wayne Doherty, Anthony Reynolds, David Kennedy

Articles

A tubular solid oxide fuel cell (SOFC) stack was modelled and its operation on biomass syn-gas was investigated. The objective of this work was to develop a computer simulation model of a biomass gasification-SOFC (BG-SOFC) system capable of predicting performance under various operating conditions and using diverse fuels. The stack was modelled using Aspen Plus and considers ohmic, activation and concentration losses. It was validated against published data for operation on natural gas. Operating parameters such as fuel and air utilisation factor U_f and U_a, current density j and steam to carbon ratio STCR were varied and …

Validation Of A Simulation Model For A Combined Otto And Stirling Cycle Power Plant, Jim Mcgovern, Barry Cullen, Michel Feidt, Stoian Petrescu

Conference Papers

A project has been underway at the Technological University Dublin (DIT) to investigate the feasibility of a combined Otto and Stirling cycle power plant in which a Stirling cycle engine would serve as a bottoming cycle for a stationary Otto cycle engine. This type of combined cycle plant is considered to have good potential for industrial use. This paper describes work by DIT and collaborators to validate a computer simulation model of the combined cycle plant. In investigating the feasibility of the type of combined cycle that is proposed there are a range of practical realities to be faced and …

Gate 3 Grid Connection Group Processing Approach:An Analysis, John Leahy

Msc. in Energy Management

The aim of this project is to analyse the Group Processing Approach (the “GPA”) to renewable generator grid connections, and in particular the Gate 3 process which is the latest round of the GPA that is currently being implemented in the Republic of Ireland, to determine if it is the most effective approach for connecting new renewable generation. Gate 3 is the third series of the GPA for connecting renewable generation to the Irish Electricity grid where applications are processed in groups or batches. The size of the Gate 3 has bee capped at 3,900MW with applicants being selected based …

An Investigation Into The Retrofitting Of Air Source Heat Pumps Into Fabric Improved, Detached, Oil Centrally Heated Dwellings In Rural Ireland, Ciara Ahern

Other resources

In Ireland the predominant house type is detached housing which constitutes 43 % of entire stock. 72% of the detached housing stock is rurally located and 68% is heated by fuel oil. 82% of houses in Ireland have a radiator heating system. Detached housing, due to larger size and high surface area to volume ratio, has a greater heat loss per m² than all other house types of the same construction period. It follows that, if a heat pump can be successfully deployed in a house of this type it can be successfully deployed in almost all other house …

Turbine House: A Net-Zero Energy House, Karen E. Hernandez

Renée Crown University Honors Thesis Projects - All

Current use of fossil fuels has raised adverse problems in today’s society. The biggest one of them is the climate change caused by emissions of greenhouse gases. For this reason, renewable energies, or energy flows which are replenished at the same rate as they are used, are needed to reduce carbon emissions in the range of 60-80% by the end of the twenty-first century. [1] Energy used in houses nationwide contributes to 16% of generated greenhouse gas emissions. [3] This large percentage of greenhouse emissions could be reduced by designing and developing energy efficient houses, or net-zero energy houses, such …

Vortex Apparatus And Demonstrations, Said Shakerin

All Faculty Articles - School of Engineering and Computer Science

Vortex flow, from millimeter to kilometer in scale, is important in many scientific and technological areas.1 Examples are seen in water strider locomotion, from industrial pipe flow (wastewater treatment) to air traffic control (safe distance between aircrafts on a runway ready for takeoff) to atmospheric studies.2-5 In this paper, we focus on a particular vortex known as bathtub vortex (BTV). It occurs when water is drained from a hole at the bottom of a container such as a bathtub or a sink under the action of gravity. The vortex has a funnel shape with a central air core, resembling a …

Dynamic Analysis Of Grid Connected Hybrid System Of Pv Panel And Wind Turbines For A Light Commercial Building, Bhavin K. Madhu

Masters Theses and Doctoral Dissertations

No abstract

Design Of A Single Alkaline Fuel Cell Test Bed, James Brunton, David Kennedy, Fergal O'Rourke, Eugene Coyle

Conference Papers

This Research focuses on the design and development of a single alkaline fuel cell test bed facility. The paper also makes reference to problems and solutions encountered during construction that resulted in a more effective fuel cell and operating system. As a sustainable and clean alternative energy option, fuel cell technology has the potential to provide electrical power for stationary and mobile applications. Hydrogen and fuel cell technologies are a viable long term energy solution, but to-date has failed to make a major impact on the energy market. Fuel Cells offer a sustainable energy options that can be cost effective …

Mechanical Milling Of Co-Rich Melt-Spun Sm-Co Alloys, Farhad Reza Golkar-Fard

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Rare-earth, high-energy permanent magnets are currently the best performing permanent magnets used today. The discovery of single domain magnetism in 1950’s ultimately led to the development of nanocomposite magnets which had superior magnetic properties. Previous work has shown that mechanical milling (MM) effectively generates nanoscale structures in Sm-Co-based alloys. MM of more Co-rich, melt-spun Sm-Co alloys (up to the eutectic composition) and the role of initial structure on the milling behavior were investigated.

Sm-Co alloys with compositions of Sm_10.5Co_89.5 and Sm₈Co₉₂ were produced by arc melting, melt-spinning and mechanical milling. X-ray diffraction results showed …

Coupled Dem-Fem For Dynamic Analysis Of Granular Systems In Bending, Kitti Rattanadit

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Characterizing the dynamic behavior of granular materials is one of the great challenges in the mechanics of granular matter. Methods for evaluating the mechanical properties of granular matter have applications in a variety of industries, mining and geotechnical activities, defense and military operations. A coupled 2D Discrete Element Method-Finite Element Method (DEM-FEM) code, called "BobKit", is developed and implemented for analyzing the behavior of a 2D granular layer on top of an elastic beam under deforming (quasi-static) or vibrating (dynamic) of the beam. The explicit time-integration dynamic code is used to simulate quasi-static and dynamic bending of the granular layer …

Hydrogen Separation Membranes, University Of North Dakota. Energy And Environmental Research Center

EERC Brochures and Fact Sheets

Technical brief describing hydrogen separation membranes and their potential to reduce cost of hydrogen production and CO₂ separation. Outlines membrane types, commercially available membranes, and new technological developments. [This item is an outdated or superseded version and retained for historical purposes only. It may no longer reflect current information, policies, or practices.]