Pulse Reverse Current Electrodeposited Tio2 Doped Ni-W Coating,
2021
The University of Akron
Pulse Reverse Current Electrodeposited Tio2 Doped Ni-W Coating, Sydney Hughes
Williams Honors College, Honors Research Projects
Nickel-Tungsten (Ni-W) coatings via the pulse reverse current method have been under development as a potential replacement for typical Chromium/Cadmium coatings. To increase the effectiveness of Ni-W as a coating, dopants have been tested to decrease microcracks and pores and increase overall tribological performance. Previous research by Timken Engineered Surfaces Laboratory showed that Ni-W doped with TiO2 nanoparticles had a positive effect on coating performance. The purpose of this study was to determine the ideal solution parameters (i.e. TiO2 concentration, pH) to maximize the benefit of the dopant when samples are subjected to tribological testing. Here, solutions of …
Increasing The Corrosion Protection Of Aisi 1008 Carbon Steel By Surface Treatment With Unmodified And Benzotriazole Modified Sol-Gel Films,
2021
The University of Akron
Increasing The Corrosion Protection Of Aisi 1008 Carbon Steel By Surface Treatment With Unmodified And Benzotriazole Modified Sol-Gel Films, Shane Thomas Kelliher
Williams Honors College, Honors Research Projects
The corrosion performance of sol-gel coated AISI 1008 carbon steel was investigated in 3.5 wt% NaCl solutions of pH 7, 9, and 12 using electrochemical measurements. A corrosion inhibitor, benzotriazole (BTA) was added to the sol-gel mixture and tested as a second, modified sol-gel coating. Sol-gel films adhered evenly to metal samples and were characterized by FTIR spectroscopy. Electrochemical Impedance Spectroscopy (EIS) showed an increase in polarization resistance from blank to sol-gel coated samples (600-18,800,000 ohms). Cyclic polarization (CPP) curves showed positive hysteresis loops for blank and unmodified sol-gel coated samples which increased at high pH following the backward potential …
Automated Control System For The Remote-Controlled Torch Positioner,
2021
The University of Akron
Automated Control System For The Remote-Controlled Torch Positioner, Christopher Ferguson, Anna Abate, Kyle Cramer, Alex Sabitsch, Jacob Stefanko
Williams Honors College, Honors Research Projects
The goal of this project is to design and implement a controls system for Dr. Morscher’s burner rig. The rig serves to simulate jet turbine conditions and test how materials, specifically ceramic matrix composites, react under high temperatures and stresses. Currently, the location of the torch relies solely on manual adjustments and has no automated control system. The improved design will automatically adjust the torch position based on the desired temperature of the sample being tested, therefore maintaining a steady environment for the sample. The current method of manual adjustments for regulating temperature is a crude solution that does not …
Atmospheric Corrosion Of Galvanically Coupled Aluminum Alloys And Carbon Steel,
2021
The University of Akron
Atmospheric Corrosion Of Galvanically Coupled Aluminum Alloys And Carbon Steel, Mitchell Felde
Williams Honors College, Honors Research Projects
Aluminum alloys are a steadily growing material being commonly used in lieu of typical steels. Additional alloying, heat treatment, and other property enhancing processes are expanding the use of these alloys. However, with this expansion, galvanic corrosion is becoming more of an issue in the design stage due to the combination of these alloys with steels. The automotive industry is one industry where the use of aluminum alloys is becoming common practice. Aluminum alloys provide a lightweight aspect over the conventional carbon steel that was used previously. As a result of this transition towards more lightweight materials, galvanic coupling is …
Evaluating The Thermoresponsive Properties Of Hydroxypropyl Cellulose Solutions For Smart Window Applications,
2021
The University of Akron
Evaluating The Thermoresponsive Properties Of Hydroxypropyl Cellulose Solutions For Smart Window Applications, Adam Reed
Williams Honors College, Honors Research Projects
With HVAC and building energy usage expected to increase, there is a strong need for autonomous thermal management solutions. In particular, there has been a growing interest in thermoresponsive (TR) smart windows that are activated by ambient temperature changes. Most TR smart windows contain a liquid solution between two panes. The goal of this research project was to develop a self-supporting smart window by forming a gel that maintained its TR properties. A gel is less prone to spilling in the case of window breakage. It was also desired to tune the phase transition to occur at environmentally relevant conditions …
Optimisation Of Retrofit Wall Insulation: An Irish Case Study,
2021
Technological University Dublin
Optimisation Of Retrofit Wall Insulation: An Irish Case Study, Rakshit D. Muddu, D M. Gowda, Anthony James Robinson, Aimee Byrne
Articles
Ireland has one of the highest rates of emissions per capita in the world and its residential sector is responsible for approximately 10% of total national CO2 emissions. Therefore, reducing the CO2 emissions in this sector will play a decisive role in achieving EU targets of reducing emissions by 40% by 2030. To better inform decisions regarding retrofit of the existing building stock, this study proposes Optimum Insulation Thicknesses (OIT) for typical walls in 25 regions in Ireland. The calculation of OIT includes annual heat energy expenditure, CO2 emissions, and material payback period. The approach taken is based on Heating …
Synthesis Of A Two-Part Geopolymer From Red Mud And Silica Fume,
2021
Chulalongkorn University
Synthesis Of A Two-Part Geopolymer From Red Mud And Silica Fume, Arup Kumar Mandal
Journal of Metals, Materials and Minerals
In this present study, the development of a two-part geopolymer from waste red mud (RM) and silica fume (SF) by alkali activator is examined. The influence of silica fume addition, alkali concentration, curing duration are studied. The compressive strength of geopolymers has been achieved 0.8 MPa to 8 MPa with varying different compositions and synthesis parameters. The optimum RM/SF ratio is 60/40, the optimum solid/solution ratio is 1.8 gmL-1 or 2 gmL-1, and the optimum Na2SiO3/NaOH ratio is 0.5 day for 28 days curing time. The incorporation of iron in the geopolymer matrix contributes to geopolymerization. The study suggests that …
Eco-Friendly Lake Pigment From Sappanwood: Adsorption Study And Its Application As Natural Colorant For Natural Rubber Toy Balloon,
2021
Chulalongkorn University
Eco-Friendly Lake Pigment From Sappanwood: Adsorption Study And Its Application As Natural Colorant For Natural Rubber Toy Balloon, Jitnapa Sirirak, Ployphat Suppharatthanya, Kedsarin Chantha, Sutinee Girdthep, Supanee Chayabutra
Journal of Metals, Materials and Minerals
Due to the awareness of the impact of synthetic dye on human health and the environment, natural dye and lake pigment have attracted considerable attention from researcher. Herein, pink−red lake pigment from sappanwood was prepared using adsorption approach. The effects of initial pH, pH and concentration of brazilein solution, dosage of aluminium hydroxide, and adsorption time on adsorption were also explored. Results showed that the maximum adsorption capacity of 30 mg g-1 was achieved when 0.25%w/v of aluminium hydroxide and 100 mg L-1 of brazilein solution were applied. The adsorption kinetics and adsorption isotherm fitted the pseudo second order model …
Using Shrimp Shells As Based Catalysts For Fame Production From Palm Oil Feedstock,
2021
Chulalongkorn University
Using Shrimp Shells As Based Catalysts For Fame Production From Palm Oil Feedstock, Assadaporn Poonanan, Anupat Prukpaiboon, Paul Egwuonw Dim, Mutsee Termtanun
Journal of Metals, Materials and Minerals
In this study, waste shrimp shells from industry were used as a heterogeneous bio-based catalyst for trans-esterification reaction of fresh palm oil. CaO was prepared from shrimp shells calcination. Surface area, phase composition, and basicity of the calcined shrimp shell catalysts were studied using N2 adsorption (BET), X-ray diffraction (XRD), and CO2 temperature-programmed-desorption (CO2-TPD), respectively. The influence of shrimp shells calcination temperature and operation condition, methanol to palm oil ratio on trans-esterification reaction, were investigated. Five hours trans-esterification was carried out at 65℃ using different shrimp shell at four different calcination temperature: 700, 750, 800 and 850℃ with 9:1 methanol …
Investigation Of Deposition Parameters On The Structural Properties And Hardness Of Tialn Films Deposited Via Reactive Pulsed Dc Magnetron Sputteringinvestigation Of Deposition Parameters On Structural Properties And Hardness Of Tialn Films Deposited By Reactive Pulsed Dc Magnetron Sputtering, Jariyaporn Rukkun, Kamon Aiempanakit, Pimchanok Reakaukot, Witthawat Wongpisan, Kirati Waree, Montri Aiempanakit
Journal of Metals, Materials and Minerals
In this work, titanium aluminum nitride (TiAlN) films were deposited on a silicon substrate via reactive pulsed DC magnetron sputtering. The effect of deposition parameters such as nitrogen gas flow rate, substrate temperature, and bias voltage on the structural and mechanical properties of TiAlN films was investigated. The crystal structure, morphology, and hardness of TiAlN films were characterized via X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM, and nanoindentation. An improved crystallinity of TiAlN films was obtained by varying the substrate temperature and bias voltage. The morphology of the TiAlN film exhibited a columnar structure, and the morphology gradually …
Improving Corrosion Resistance Of 3d Printed Ti-6al-4v By Tin Coating,
2021
Chulalongkorn University
Improving Corrosion Resistance Of 3d Printed Ti-6al-4v By Tin Coating, Surada Nisaimun, Phitsanu Poolcharuansin, Patama Visuttipitukul, Pitichon Klomjit
Journal of Metals, Materials and Minerals
TiN thin films were deposited on biomaterial 3D printed Ti-6Al-4V substrates using two methods including direct current magnetron sputtering (DCMS) and high-power impulse magnetron sputtering (HiPIMS). The coating times were compared between 5 min and 25 min. HiPIMS was developed based on DCMS by increasing degree of ionization in plasma and power densities in the order of kWcm-2 compared to Wcm-2 of DCMS. The film characteristics and mechanical properties were investigated by glancing incident x-ray diffractometer (GIXRD), field emission scanning electron microscope (FE-SEM), and atomic force microscope (AFM). Electrochemical behavior was analyzed by electrochemical impedance spectroscopy (EIS) in 1 M …
Characteristic Of Fluorescence Spectroscopy Response Of Tetrakis (4-Sulfonatophenyl) Porphyrin Doped Polyaniline Toward Fe3+ Ion,
2021
Chulalongkorn University
Characteristic Of Fluorescence Spectroscopy Response Of Tetrakis (4-Sulfonatophenyl) Porphyrin Doped Polyaniline Toward Fe3+ Ion, Chatr Panithipongwut Kowalsk, Meatawadee Buntee, Prasit Pattananuwat
Journal of Metals, Materials and Minerals
Here, we report a selective colorimetric chemosensor toward Fe3+ ion detection by the combination of sensitizer and hole transport consisting of polyaniline and tetrakis (4-sulfonatophenyl) porphyrin. Interestingly, the presence of tetrakis (4-sulfonatophenyl) porphyrin moiety on polyaniline can enhance the optical limiting properties of polyaniline, allowing the fluorophore signal for chemical sensor. The performance sensing behaviors toward metal ion are observed by the ultraviolet-Visible and fluorescence properties. The sensing of polyaniline-tetrakis (4-sulfonatophenyl) porphyrin toward Fe3+ ion exhibits a linear response in the concentration range of 0.01 M to 1.0 × 10-4 M over the other transition metals (Cu2+, Ni2+, Zn2+, Pb2+, …
The Study On Un-Doped/Boron Doped/Un-Doped Triple Seg In Vertical Nand Flash Memory,
2021
Chulalongkorn University
The Study On Un-Doped/Boron Doped/Un-Doped Triple Seg In Vertical Nand Flash Memory, Woong Lee, Chaeho Kim, Joonsuk Lee, Sehun Park, Yonghan Roh
Journal of Metals, Materials and Minerals
Selective epitaxial growth (SEG) plays a critical role in vertical NAND flash memory because it serves as a ground select line (GSL) transistor, which is used to control the cell current in the vertical channel. In this study, different channel hole sizes between the adjacent hole and away hole from the common source line (CSL) were detected after vertical channel etch (VCE). This discrepancy severely impacts the boron concentration of SEG applied through ex-situ boron implantation, and results in large GSL Vth variations. Novel in-situ boron-doping of triple-layered un-doped/boron doped/un-doped SEG was developed to solve the high variation of the …
Microwave-Assisted Ecofriendly Silver Nanoparticle Synthesis By Varieties Of Chrysanthemum Morifolium Ramat: Assessing Their Antioxidant, Photocatalytic And Antibacterial Activities,
2021
Chulalongkorn University
Microwave-Assisted Ecofriendly Silver Nanoparticle Synthesis By Varieties Of Chrysanthemum Morifolium Ramat: Assessing Their Antioxidant, Photocatalytic And Antibacterial Activities, Mathivathani Kandiah, Laknee Nawamali De Silva
Journal of Metals, Materials and Minerals
Based on recent developments in the field of Nanobiotechnology, this study is aimed at the assessment of antioxidant, photocatalytic and antibacterial activities of silver nanoparticles (AgNPs) synthesized using Chrysanthemum morifolium Ramat varieties (brown, yellow, purple, pink, salmon pink and white), where five varieties produced AgNPs except white. Antioxidant assays such as total flavonoid content, total phenolic content and total antioxidant capacity and free radical scavenging assays such as ferric reducing antioxidant power and DPPH radical scavenging assays were performed. Photocatalytic activity was assessed by the degradation of the model dye methylene blue. Anti-bacterial activity was determined on Staphylococcus aureus and …
Improvement Of The Superconducting Properties Of Carbon Addition On Bi1.6pb0.4sr2 Ca2cu3o10+Δ Prepared Through The Two-Step Sintering Process,
2021
Chulalongkorn University
Improvement Of The Superconducting Properties Of Carbon Addition On Bi1.6pb0.4sr2 Ca2cu3o10+Δ Prepared Through The Two-Step Sintering Process, Dini Rizqi Dwikunti Siregar, Sigit Dwi Yudanto, Septian Adi Chandra, Eka Feby Ronauli Lubis, Syahrul Humaidi, Nono Darsono
Journal of Metals, Materials and Minerals
The effects of the addition of carbon nanoparticles and nanotubes on the Bi1.6Pb0.4Sr2Ca2Cu3O10+δ (BPSCCO) have been reported. BPSCCO samples were synthesized using the sol-gel method. BPSCCO with nominal composition was sintered at 840°C for 30 h, then grounded and added an amount of carbon. Pure and carbon added BPSCCO were sintered at 840°C for 30 hours. Resistivity measurements were carried out to determine the superconducting properties of the samples. We found that the addition of carbon nanoparticles and nanotubes increased the critical zero temperature (Tc-zero) of BPSCCO from 94.67 K to 97.8 K and 102.03 K for the pure BPSCCO, …
Stress Softening Characteristics Of Thin Monoholar Rubber Flat Slab,
2021
Chulalongkorn University
Stress Softening Characteristics Of Thin Monoholar Rubber Flat Slab, Kulyuth Boonseng, Chatchai Waiyapattanakorn, Prayoon Surin
Journal of Metals, Materials and Minerals
Thin monoholar rubber flat slab gives rise to unconventional mechanical properties under tension loading not found in thin solid rubber flat slab. However there has been no proper report on its stress softening characteristics. Stress softening is an important phenomenon occurring in all elastomeric materials under cyclic tension loading. Parameters pertinent to stress softening investigated in this research are stress-strain characteristics, permanent set strain and hysteresis loss energy of the thin monoholar rubber flat slab in comparison with the thin solid rubber fat slab when undergoing 7 cycles of stretching. Noticeable differences of stress-strain hysteresis loops diminution of the thin …
Photoelectrochemical Cathodic Protection Of Amorphous Zinc Oxide Coating On Hot Rolled Steel Ss400 In A 3 Wt% Nacl Solution And A Na2s-Naoh Solution,
2021
Chulalongkorn University
Photoelectrochemical Cathodic Protection Of Amorphous Zinc Oxide Coating On Hot Rolled Steel Ss400 In A 3 Wt% Nacl Solution And A Na2s-Naoh Solution, Phatchara Wipataphan, Worapot Sripianem, Naw Blessing Oo, Thanate Na Wichean, Boossayamas Dachbumroong, Oratai Jongprateep, Gasidit Panomsuwan, Naray Pewnim, Ratchatee Techapiesancharoenkij
Journal of Metals, Materials and Minerals
The photoelectrochemical cathodic protection of amorphous ZnO thin-film coating on hot rolled steel SS400, in the 3 wt% NaCl environment, was investigated. The ZnO thin film was coated on a SS400 substrate at 200℃ using the spray pyrolysis technique. The x-ray diffractometry analysis confirmed the amorphous ZnO coatings. Two different types of the electrochemical cells were used: a single-cell and a double-cell system. Two different types of the photoelectrolytic solutions were compared: (i) 0.1 M Na2S + 0.2 M NaOH and (ii) 3 wt% NaCl solution. The ZnO-coated SS400 samples were subjected to potentiostatic polarization testing under dark and UV …
Influence Of Graphite Feedstock On The Characteristics Of Silver-Decorated Graphene Oxide And Antimicrobial Property,
2021
Chulalongkorn University
Influence Of Graphite Feedstock On The Characteristics Of Silver-Decorated Graphene Oxide And Antimicrobial Property, Ebrahim Mahmoudi, Wei Lun Ang, Gasidit Panomsuwan, Oratai Jongprateep, Abdul Wahab Mohammad, Law Yong Ng, Muneer M. Ba-Abbad
Journal of Metals, Materials and Minerals
Graphite from different sources has significant influence on the properties of graphene oxide (GO) and reactivity of GO towards further modification with other nanoparticles. However, such effect has not yet been properly explored. This study aims to investigate the characteristics and antimicrobial property of GO decorated with silver nanoparticles (known as Ag-GO composite) where the GO is synthesized via modified Hummer’s method from various graphite feedstock, namely natural graphite flake (NGF), natural graphite powder (NGP), and synthetic graphite powder (SGP). The Ag-GO nanocomposite was then synthesized using chemical reduction methods. Antimicrobial properties of the Ag-GO were tested using the standard …
Preparation Of A Mixed Al/Sc Nano-Oxide Derived From The Bauxite Residue (Red Mud) Via The Sulfuric Acid Roasting–Leaching–Precipitation Process,
2021
Chulalongkorn University
Preparation Of A Mixed Al/Sc Nano-Oxide Derived From The Bauxite Residue (Red Mud) Via The Sulfuric Acid Roasting–Leaching–Precipitation Process, Razieh Habibpour, Eslam Kashi, Mehdi Janfada
Journal of Metals, Materials and Minerals
In this study, three methods were used and compared for the selectable extraction of aluminum/ scandium with the least amount of iron in red mud (RM) samples from the Iran alumina plant in Jajarm as follows: 1) RM direct acid leaching with H2SO4, 2) RM washing with hydrochloric acid and oxalic acid before leaching with H2SO4, and 3) RM sulfuric acid roasting-leaching-precipitation. The aim was to extract the highest amount of scandium while preventing the leaching of other metals, especially iron. Due to any discriminative features, the selective separation of Al/Sc with …
Interface Characterization In Tungsten Fiber/Zr-Based Bulk Metallic Glass Matrix Composite,
2021
Chulalongkorn University
Interface Characterization In Tungsten Fiber/Zr-Based Bulk Metallic Glass Matrix Composite, Mohammad Ammar Mofid, Mostafa Jafarzadegan
Journal of Metals, Materials and Minerals
In this research, Zr55Cu30Al10Ni5 bulk metallic glass (BMG) alloy is used as the base material to form tungsten fiber reinforced BMG composites. The composites are synthetized using melt infiltration casting method and their microstructure and compressive properties are investigated. Two different infiltration times of 10 min and 15 min are used to produce the composites. The microstructural evaluation of the interface between tungsten fiber and BMG matrix reveals that a narrow reaction band emerges between the tungsten wires and BMG alloy. Some portions of this layer are broken into the fine Zr/W-rich particles …
