Materials Science and Engineering Commons^™

Potential Advantages Of Basalt Frp Bars Compared To Carbon Frp Bars & Conventional Steel, Yosra El Maghraby, Mohamed Nagib Abou-Zeid Prof., Ezzeldeen Yazeed El Sayed Ahmed Prof

Civil Engineering

No abstract provided.

The Effects Of Rigid Polyurethane Foam As A Confinement Material On Breaching Charge Detonations, Nathan Franz Paerschke-O'Brien

Masters Theses

"The effects of a rigid polyurethane foam used as a confinement material on four types of breaching explosives were tested, focusing on the changes in shockwave peak pressures, detonation load compression forces, and brisance cratering abilities. The Plate Dent testing procedure was modified to incorporate a load cell force sensor, and two air overpressure sensors were included adjacent to the blast to quantify each test result. The testing variables focused on the polyurethane foam cure times and thickness volumes around the breaching explosives to determine the breaching charges' optimal energy output capabilities when confined by the foam material. The rigid …

Relating Detonation Parameters To The Detonation Synthesis Of Nanomaterials, Martin Langenderfer

Doctoral Dissertations

“This research investigates the physical and chemical processes that contribute to the detonation synthesis of silicon carbide nanoparticles. Bulk production of SiC nanoparticles through detonation is possible due to pressures achieved over 20 GPa and temperatures over 2000 K as well as quenching rates in excess of 13 billion K/second. These conditions catalyze reaction and bottom-up molecular growth while retaining particles < 100 nm in diameter. In this work, detonation synthesis of SiC was demonstrated by incorporation of polycarbosilane, an SiC precursor material, into an RDX/TNT explosive matrix prior to detonation. Detonation Synthesis of SiC was also accomplished by reacting elemental silicon with carbon liberated by the detonation of negatively oxygen balanced TNT. Hydrodynamic simulation of a 60:40 mass ratio RDX/TNT detonation created conditions thermodynamically suitable to produce cubic silicon carbide within the first 500 nanoseconds after the passage of the detonation wave while carbon remains chemically reactive for molecular formation. Simulations and experimental tests indicated that loading configuration and impedance mismatch of the precursor additives used in detonation synthesis results in conditions in the additives that exceed the accepted detonation pressure of the explosive by greater than three times. Finally, a full factorial experimental design showed increasing silicon concentration, reducing silicon size, and reducing oxygen balance by adjusting the ratio of RDX to TNT decreased the explosives detonation pressure by 20% and increased the soot yield and concentration of SiC observed in the detonation products by 82% and 442% respectively”--Abstract, page iv.

Experimental And Numerical Studies Of Novel Thermal Energy Storage Materials For Applications In Concrete And Energy Storage Systems, Wenyu Liao

Doctoral Dissertations

In this work, several types of novel thermal energy storage (TES) materials and composites are explored, and a series of numerical simulation models and experimental protocols are developed to evaluate the potentials of these materials to be applied in concrete, pavement, and thermal energy storage systems.

The first two types of novel TES materials/composites are at the micro-scale, which use micro diatomite (DE) and cenosphere (Ceno) as carriers of phase change material (PCM), respectively. The third type of novel TES material is at the macro-scale, utilizing lightweight sand (LWS) and lightweight coarse aggregate as carriers to load PCM. The last …

Combined Puncture And Cutting Of Soft-Coated Fabrics By A Pointed Blade: Energy, Force, And Stress Failure Criteria, Ennouri Triki, Chantal Gauvin

Études primaires

Soft elastomer-coated fabrics are widely used in engineering and protective applications. Puncture cutting by sharp-tipped objects is one of the most common failure modes of protective gloves made of coated fabrics. In order to investigate the puncture-cutting process of soft elastomer-coated fabrics, we studied the mechanisms and mechanics of pointed-blade insertion into specimens cut out from four protective gloves. Experimental and analytical analyses showed that total energy and critical puncture-cutting force calculated analytically are both able to predict the puncture-cutting resistance of soft elastomer-coated fabrics measured experimentally. Total energy is obtained from the relationship between the puncture-cutting work and the …

Theoretical Analysis Of Experimental Data Of Sodium Diffusion In Oxidized Molybdenum Thin Films, Orlando Ayala, Benjamin Belfore, Tasnuva Ashrafee, John Akwari, Grace Rajan, Shankar Karki, Deewakar Poudel, Sylvain Marsillac

Engineering Technology Faculty Publications

In this work, the diffusion process of sodium (Na) in molybdenum (Mo) thin films while it was deposited on soda lime glass (SLG) was studied. A small amount of oxygen was present in the chamber while the direct-current (DC) magnetron sputtering was used for the deposition. The substrate temperatures were varied to observe its effect. Such molybdenum films, with or without oxidations, are often used in thin film solar cells, either as back contact or as hole transport layers. Secondary ion mass spectrometry (SIMS) was used to quantify the concentration of the species. A grain diffusion mechanistic model incorporating the …

The Effect Of Tin-, Ticn-, Tialn-, And Tisin Coated Tools On The Surface Defects And Geometric Tolerances Of Holes In Multi-Spindle Drilling Of Al2024 Alloy, Muhammad Aamir, Adrian Davis, William Keeble, Ugur Koklu, Khaled Giasin, Ana Vafadar, Majid Tolouei Rad

Research outputs 2014 to 2021

The integrity of machined holes depends on many parameters, some of which are related to the cutting tool (geometry, coating, material). Other influential parameters are related to the machining process variables (spindle speed, feed rate, workpiece material), all of which can affect the quality of the hole and drilling induced damage on its surface. This study investigates the effect of uncoated tools and four types of tool coatings (TiN-, TiCN-, TiAlN-, and TiSiN) on the hole quality and its microstructure. The study analyzed several hole geometrical metrics, namely hole size, circularity, cylindricity, and perpendicularity of an Al2024 aluminum alloy using …

Microstructure Evolution And Mechanical Property Response Of Tc11 Titanium Alloy Under Electroshock Treatment, Chang Liu, Lechun Xie, Dongsheng Qian, Lin Hua, Liqiang Wang, Lai-Chang Zhang

Research outputs 2014 to 2021

© 2020 The Authors This work investigated the effects of electroshock treatment (EST) on the microstructure variation and mechanical properties of TC11 alloy. The average hardness of the specimens decreased from 358 HV to 328 HV after EST of 0.04 s, then increased to 396 HV after EST of 0.06 s. After EST, the yield strength of specimen declined from 959 MPa to 797 MPa after EST of 0.04 s, and then increased to 1265 MPa after EST of 0.06 s, but the fracture strain decreased continuously. The variation in mechanical properties was closely related to the phase transition from …

New Horizons For Processing And Utilizing Red Mud, M. Archambo

Dissertations, Master's Theses and Master's Reports

Red mud is an industrial slurry waste that is produced as a byproduct of the Bayer process for alumina. The waste is generated in large quantities, up to a ratio of 2:1 against the valued product alumina. Red mud exhibits many chemical and physical properties that categorize it as a hazardous material. Due to the addition of sodium hydroxide in processing, the pH is typically at values close to 13. Small particle size discourages separation from water for disposal, so drying red mud happens over many years.

The pH of red mud can be reduced with inexpensive reagents. Carbon dioxide …

Anaerobic Reductive Bioleaching Of Manganese Ores, Neha Sharma

Dissertations, Master's Theses and Master's Reports

The increasing demand of manganese in the industries and various hindrances in its production from low grade ores by conventional method has made it imperative for researchers around the world to develop a method of manganese extraction from low grade ores that is both environment friendly and economical. Bioleaching has shown significant potential in manganese extraction and efficiencies of extraction have been found to be 70-98% with the help of various bacteria and fungi.

This study focuses on extraction of manganese with the help of mixed bacterial strains that have been collected from their natural anaerobic environment. The extraction of …

Studying The Effects Of Initial Crack Angle On The Crack Propagation In Graphene Nano-Ribbon Through Molecular Dynamics Simulations, Vijay Kumar Pathak

Dissertations, Master's Theses and Master's Reports

In this research, we have worked on the brittle fracture of graphene nano-ribbon to explore the behavior of crack propagation at different crack angles. We have performed classical Molecular Dynamics simulations using LAMMPS at ten different crack angles between 0 degrees and 45 degrees, in an increment of 5 degrees to observe the parameters that dominate the crack path. The graphene nanoribbon is loaded in the zigzag direction by pulling it in the armchair direction with a pre-existing crack in the center. We have used OVITO for the visualization of the simulation. AIREBO potential is employed in this work because …

Understanding Flow Characteristics In Metal Additive Manufacturing, Carl R. Hartsfield, Travis E. Shelton, Gregory R. Cobb, Ryan A. Kemnitz, Joseph Weber

Faculty Publications

In fluid flow, the frictional effects from interior surfaces of flow components create pressure loss across the surface. Understanding this inherent pressure loss due to friction and other phenomena is important when designing a flow system. For conventional manufacturing, friction loss has been empirically studied and is well known in the engineering community. However, newer manufacturing techniques, such as laser powder bed fusion (LPBF), an additive manufacturing technique, need to be understood. The inherent flow conditions resulting from the additive processes were studied. Test samples were printed with the flow path oriented in the vertical direction with different channel diameters …

Experiments And Modeling Of The Chemo-Mechanically Coupled Behavior Of Polymeric Gels, Nikola Bosnjak

Dissertations

Polymeric materials consist of mutually entangled or chemically crosslinked long njitmolecular chains which form a polymer network. Due to their molecular structure, the njitpolymeric materials are known to undergo large deformation in response to various njitenvironmental stimuli, such as temperature, chemical potential and light.

When a polymer network is exposed to a suitable chemical solvent, the solvent molecules are able to diffuse inside the network, causing it to undergo a large volumetric deformation, known as swelling. In addition to volumetric deformation, this process involves the chemical mixing of the polymer network and solvent molecules, and is typically environmentally responsive. A …

Cooling Under Applied Stress Rejuvenates Amorphous Alloys And Enhances Their Ductility, Nikolai Priezjev

Mechanical and Materials Engineering Faculty Publications

The effect of tensile stress applied during cooling of binary glasses on the potential energy states and mechanical properties is investigated using molecular dynamics simulations. We study the three-dimensional binary mixture that was first annealed near the glass transition temperature and then rapidly cooled under tension into the glass phase. It is found that at larger values of applied stress, the liquid glass former freezes under higher strain and its potential energy is enhanced. For a fixed cooling rate, the maximum tensile stress that can be applied during cooling is reduced upon increasing initial temperature above the glass transition point. …

Treated Hfo2 Based Rram Devices With Ru, Tan, Tin As Top Electrode For In-Memory Computing Hardware, Yuvraj Dineshkumar Patel

Theses

The scalability and power efficiency of the conventional CMOS technology is steadily coming to a halt due to increasing problems and challenges in fabrication technology. Many non-volatile memory devices have emerged recently to meet the scaling challenges. Memory devices such as RRAMs or ReRAM (Resistive Random-Access Memory) have proved to be a promising candidate for analog in memory computing applications related to inference and learning in artificial intelligence. A RRAM cell has a MIM (Metal insulator metal) structure that exhibits reversible resistive switching on application of positive or negative voltage. But detailed studies on the power consumption, repeatability and retention …

Optimization Composition Of The Wood-Polymer Composition Based On Polyvinylchloride, Aliyev Sunnatulla, Ilkhamov Giyos, Jurayev Asror, Magrupov Farkhad

CHEMISTRY AND CHEMICAL ENGINEERING

The objective of the reaserch is to elaboration the composition of a wood-polymer composition based on polyvinyl chloride with improved performance properties. The influence of the components of the composition - modifiers, lubricants, regulators and stabilizers - on the properties of the composition was researched. Optimization of the composition of wood-polymer composition based on PVC made it possible to obtain a material with higher strength and fire resistance.

Synthesis Of High-Strength Ceramics Based On Technogenic Waste Containing Aluminum Oxide, Shermatov Zhavokhir, Aripova Mastura, Paizyllakhanov Mukhammade-Sultankhan

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of this work is to synthesize wear-resistant and heat-resistant ceramics based on aluminum oxide. The man-made aluminum-containing waste of the Shurtan gas chemical complex was used as a source of aluminum oxide. In the work, the dependences «composition-structure», «composition-property» and «property-size of particles» were obtained, obtained by the method of heliomaterials science, namely by melting raw materials in a stream of concentrated solar radiation of high density (350 W/cm2) with subsequent quenching of the melt into water (103 deg/s). It is shown that the wear resistance and heat resistance of the material sharply increase when the content in …

High-Efficient And New Technology For Producing 5-Nitro-2-Acetylaminobenzimidazole, Saidov Sarvar, Abdurazakov Askar, Karimov Rikhsibay, Khvan Alla

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of this work is to create new veterinary products for agriculture based on local raw materials, to develop a highly efficient technology for their production. Waste from the production of medamine produced in the pilot production of the Institute of Plant Chemistry of the Academy of Sciences of the Republic of Uzbekistan. The process of synthesis of 5-nitro-2-acetylaminobenzimidazole was studied by one-factor experiments. The structure of the obtained product was investigated by IR, Mass, 1H, 13C NMR spectroscopy. The main factors influencing the process of obtaining 5-nitro-2-acetylaminobenzimidazole were revealed. On the basis of the obtained research results, a …

Low-Resistance Bi/Pb Ceramics Containing Ts = 295К-315k Phases Synthesized In A Solar Furnace (Parkent), Gulamova Dilbara, Gulamov Timur

CHEMISTRY AND CHEMICAL ENGINEERING

The aim of this work is to obtain bulk textured superconducting ceramics based on glass-crystalline precursors of the Bi1.7Pb0.3Sr2Ca(n-1)CunOy (n=5-9) series. Technologies for obtaining superconducting materials are presented. The advantages of melt methods and “Super Fast Aloys Quenching–T” technology is shown. Compositions, methods of synthesis and study of properties of precursors and ceramics obtained by solar energy are presented. The interrelation of the morphology of glass-crystalline precursors and superconducting ceramics based on them is revealed. It is shown that nano-sized nuclei are the basis on which superconducting phases with Ts = 295-315K are formed as a result of the peritectic …

Effect Of 18-Crown-6 Additive On Chromium Electrodeposition In Ionic Liquid, Yi-Jie Wang, Dong-Fang Niu, Xin-Sheng Zhang

Journal of Electrochemistry

Trivalent chromium ion (Cr³⁺) is used for electrodeposition due to its low toxicity. Electrodeposition in ionic liquids can greatly solve for hydrogen evolution problem. However,as a widely used Cr(III) precursor, chromium chloride hydrate (CrCl₃·6H₂O), still contains water. In the presence of water, Cr³⁺ will form a complex coordination structure with water molecules ([Cr(H₂O)₆]³⁺), which is a stable octahedral structure and is difficult to be directly reduced to chromium metal. Therefore, coordination agents should be added into the bath. In this work, the effect of 18-Crown-6 additive on …