Materials Science and Engineering Commons^™

Doping Graphene With Substitutional Mn, Pin-Cheng Lin, Renan Villarreal, Simona Achilli, Harsh Bana, Maya N. Nair, Antonio Tejeda, Ken Verguts, Stefan De Gendt, Manuel Auge, Hans Hofsäss, Steven De Feyter, Giovanni Di Santo, Luca Petaccia, Steven Brems, Guido Fratesi, Lino M. C. Pereira

Advanced Science Research Center

We report the incorporation of substitutional Mn atoms in high-quality, epitaxial graphene on Cu(111), using ultralow-energy ion implantation. We characterize in detail the atomic structure of substitutional Mn in a single carbon vacancy and quantify its concentration. In particular, we are able to determine the position of substitutional Mn atoms with respect to the Moiré superstructure (i.e., local graphene-Cu stacking symmetry) and to the carbon sublattice; in the out-of-plane direction, substitutional Mn atoms are found to be slightly displaced toward the Cu surface, that is, effectively underneath the graphene layer. Regarding electronic properties, we show that graphene doped with substitutional …

Testing The Effectiveness Of Various Fabrics For Use In Protective Face Coverings, Isaac Daley

Williams Honors College, Honors Research Projects

Facemask requirements have been heavily implemented as a result of the COVID-19 pandemic. The purpose of this study was to test various fabrics that could be used in face coverings and determine which materials are best for reducing virus transmission rates. Of the seven fabrics tested, five were conventional home-use fabrics and the other two were surfaces modified with hydrophobic organosilanes. Wettability and droplet adherence tests were performed on each material. The materials that performed the best were decyltrichlorosilane (DTS) modified cotton, perfluorotrichlorosilane (FTS) modified cotton, and polyester. Contact angles for water droplets on these fabrics were 106°, 93°, and …

Investigation Of Surface Charge Using Faraday Bucket Measurements: Analysis On Electrospun Polyvinylidene Fluoride Fiber Mats, Ryan Kantenwein

Williams Honors College, Honors Research Projects

Piezoelectric polymer materials such as polyvinylidene fluoride exhibit beneficial properties for use in personal protective equipment (PPE) against viral contaminants and other foreign microparticles. The electrospinning process of this material allows for surface charge to develop over a controlled surface area. Kynar 761 at 10 wt% demonstrates increased surface charge after withstanding a flow of aerated NaCl particles from a TSI 8130 instrument. Utilizing voltage measurements from a Faraday bucket, 18 wt% Kynar 761 and MG-15 exhibit surface charge when undergoing an electrospinning process; however, Kynar MG-15 displays lower charge values than that of Kynar 761. Several critical factors such …

Design And Analysis Of One-Piece 10” Carbon Fiber Wheels For Zips Racing Zr20 Formula Sae Racecar, Patrick Kruse, Henry J. Wathen, Jordan J. Hyde, Nicholas D. Dobben, Jordan D. Blake

Williams Honors College, Honors Research Projects

Reducing the weight of a vehicle in racing can substantially improve the vehicle dynamics and general performance capabilities. More specifically, the reduction of the unsprung corner weight can provide noticeable performance gains in handling and responsiveness, leading to a quicker, more agile car due to a lower yawing moment of inertia. Unsprung weight reduction also improves the car’s ability to maintain contact between the tires and the road surface for a more consistent grip. In this project we identified the loads that act on the wheel rims according to the data collected from the sensors in the car’s suspension, and …

Tabletop Dome Tester, Dylan Davis

Williams Honors College, Honors Research Projects

The project for the dome tester stand is a continuation from a group of four that worked on the stand in Spring of 2020. The project itself is based around the Erichsen Cupping test to test the material properties, in our application specifically, observing the forming limits of strain in deep drawing applications of sheet metal. Testing pieces in varying lengths from 4” x 4” squares to 4” x 0.5” strips to the depth that necking begins on the piece to determine the limit before cracks appear using a hemispherical punch to draw the material sample clamped between two dies. …

Studies In Additive Manufacturing Techniques For Pulsed Fusion Experiments, Michael Canary

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Application Of Laser Assisted Ultrasonic Nanocrystal Surface Modification On Aluminum And 3d Printed Titanium, Eman Hassan, Thomas Crouse

Williams Honors College, Honors Research Projects

A novel surface treatment, laser assisted ultrasonic nanocrystal surface modification (LA-UNSM), has proved effective in increasing surface hardness, and fatigue life. The objective of this research is to determine the effectiveness of this process on components created with additive manufacturing. To accomplish this, we investigated the effectiveness of LA-UNSM treatment on aluminum, a common 3d printed metal, and the effectiveness of LA-UNSM processing on 3d printed titanium. We first conducted our own literature review to assess the practicality of using this same treatment on aluminum. We then treated traditionally manufactured aluminum at varying levels of laser intensity to determine if …

Jominy Hardenability Tester Redesign, Dennis Kopacz, Shadoe Beatty, Thomas Benenati, Jared Mclean, Matthew Yokosuk

Williams Honors College, Honors Research Projects

Our project is Redesigning a Hardenability Tester. The goal of this project is to figure out how to incorporate an intensive quenching system to the current design from last years group. An intensive quench is a new system that is safer to harden steel and it hardens steel more effectively than other quenching processes. This will be achieved through testing the initial design to make sure it is able to run. After that as a group we will take this system through a design process to introduce a safe process of intensive quenching to the tester.

Exploring Rapid Solidification And Equal Channel Angular Pressing In The Fabrication Of Mg-Based Alloys For Medical Applications, Emily Tom

Dissertations, Master's Theses and Master's Reports

The development of magnesium bioresorbable implants has become increasingly popular due to the increased need for temporary implants and magnesium’s excellent biocompatibility and suitable elastic modulus. Even though magnesium is an excellent candidate, when alloyed with other metals magnesium’s corrosion rate becomes too rapid for bioresorbable medical applications. The investigation into novel processing techniques to control the formation of precipitates to improve mechanical strength and ductility as well as corrosion rates has become of interest. This work investigates the combination of two nonequilibrium processing techniques, rapid solidification (RS) and equal channel angular pressing (ECAP), and the effects it has on …

Advance Metallic Reinforcement Of Vat Photo Polymerized Parts, Scott Zinn

UNF Graduate Theses and Dissertations

The metallization or metallic reinforcement of polymer parts has been widely used in industry for several decades. Polymer parts are classically metalized for aesthetics, chemical and thermal resistance, electrical conductivity, and mechanical strength. Metallization has been shown to increase strength of polymer parts when compared to the strength of the bulk material without metallization. Additive manufacturing (AM) techniques that have emerged in the last few decades produce parts with different surface features and chemistry than the typical polymer part produced through injection molding. AM parts are typically weaker than traditionally manufactured parts from the same material due to intrinsic details …

Nature-Inspired Material Strategies Towards Functional Devices, Sayantan Pradhan

Theses and Dissertations

Naturally sourced, renewable biomaterials possess outstanding advantages for a multitude of biomedical applications owing to their biodegradability, biocompatibility, and excellent mechanical properties. Of interest in this dissertation are silk (protein) and chitin (polysaccharide) biopolymers for the fabrication of functional biodevices. One of the major challenges restricting these materials beyond their traditional usage as passive substrate materials is the ability to combine them with high-resolution fabrication techniques. Initial research work is directed towards the fabrication of micropatterned, flexible 2D substrates of silk fibroin and chitin using bench-top photolithographic techniques. Research is focused on imparting electrochemical properties to silk proteins using conducting …

Accident Tolerant Fuels Claddings And The Evolution Of Their Surface Characteristics Under Critical Heat Flux, Rajnikant V. Umretiya

Theses and Dissertations

Enhanced Accident Tolerant Fuels (ATFs) systems for light water reactors require higher temperature oxidation resistance in steam environments than the current UO₂ – zirconium fuel system. Investigating the ATF materials’ surface properties is needed as they have evidenced to affect the Critical Heat Flux (CHF), which is an important parameter of the thermal-hydraulic performance required to provide safety margins. In this dissertation, the surface properties of FeCrAl alloys (APMT and C26M), Zircaloy-2, Zircaloy-4, and Cr-coating on Zircaloy-4 substrates produced by Physical Vapor Deposition (PVD) and Cold Spray (CS) were investigated according to their chemistry, topography, and wettability. The static …

Equations Of State For Warm Dense Carbon From Quantum Espresso, Derek J. Schauss

Theses and Dissertations

Warm dense plasma is the matter that exists, roughly, in the range of 10,000 to 10,000,000 Kelvin and has solid-like densities, typically between 0.1 and 10 grams per centimeter. Warm dense fluids like hydrogen, helium, and carbon are believed to make up the interiors of many planets, white dwarfs, and other stars in our universe. The existence of warm dense matter (WDM) on Earth, however, is very rare, as it can only be created with high-energy sources like a nuclear explosion. In such an event, theoretical and computational models that accurately predict the response of certain materials are thus very …

Impact Dynamics Of Surfactant-Laden Droplets On Non-Wettable Coatings, Amir Esmaeili

Theses and Dissertations

Owing to their excellent water repellency, non-wettable (superhydrophobic) coatings have gained tremendous attention in the past couple of decades. Alkyl ketene dimer (AKD), an inexpensive polymer frequently used in paper industry as a sizing agent, has shown potentials to become superhydrophobic. The formation of a porous structure after curing the solidified AKD for an extra-long time (4–6 days) results in superhydrophobicity, i.e., a static contact angle with water of >150° and a roll-off angle of <10°. In this work, a facile and low-cost method was used to turn the surface of AKD superhydrophobic in a very short period of time by briefly treating the coatings, obtained from isothermally heated molten AKD at 40 °C for 3 min, with ethanol. The resulting superhydrophobicity is due to the formation of porous, entangled irregular micro/nano textures that create air cushions on the surface leading to droplet state transition from Wenzel to Cassie. As a proof of concept, the same material was applied to the co-sputtered nickel-tungsten thin films, commonly used in micro/nano-electro-mechanical systems, to improve their hydrophobicity. According to the results, at least 20% increase was observed in the dynamic contact angles of the treated substrates.

In addition, this work presents a detailed high-speed imaging analysis of the influence of the molecular weight, concentration and ionic nature of surfactants on droplet …

Continuous Preparation And Application Of Novel Heterogeneous Catalysis, Michael B. Burkholder

Theses and Dissertations

Transition metal heterogeneous catalysts are widely used across many chemical industries to reduce waste and emissions and reduce production time while increasing rate. The prevalence of these materials results from the complex relationship between metal nanoparticles and supports affecting final catalytic performance. Rational catalyst synthesis describes the ability to precisely engineer structures through controlled preparation. Novel materials and continuous processing represent a promising approach for rational catalyst synthesis.

The application of these catalysts in continuous, multiphase processes, such as cross-coupling reactions, oxidation chemistry, and nitroreduction processes, are paramount to developing new commercial routes for high-value products. Pd/G catalysts synthesized by …

Surface Characterization Of Accident Tolerant Fuel Claddings Candidates After Prolonged Exposure To Steam Oxidation, Connor F. Donlan

Theses and Dissertations

Accident Tolerant Fuel Claddings are designed to improve fuel performance and safety in abnormal reactor conditions. The development of these cladding materials has become a top priority for the nuclear community, with incidents such as the Three Mile Island accident and the Fukashima Dai-chi accident. The development of these claddings has resulted in 2 subsections: coating current claddings or replacing cladding materials with new materials. The claddings studied in this thesis are a Zircaloy-4 cladding coated with chromium through physical vapor deposition, Zircaloy-4, and a FeCrAl alloy, C26M. This thesis assessed the surface chemistry, roughness, and wettability after extended exposure …

Applied Machine Learning In Extrusion-Based Bioprinting, Shuyu Tian

Theses and Dissertations

Optimization of extrusion-based bioprinting (EBB) parameters have been systematically conducted through experimentation. However, the process is time and resource-intensive and not easily translatable across different laboratories. A machine learning (ML) approach to EBB parameter optimization can accelerate this process for laboratories across the field through training using data collected from published literature. In this work, regression-based and classification-based ML models were investigated for their abilities to predict printing outcomes of cell viability and filament diameter for cell-containing alginate and gelatin composite hydrogels. Regression-based models were investigated for their ability to predict suitable extrusion pressure given desired cell viability when keeping …

Quality Assurance Of Lightweight Structures Via Phase-Based Motion Estimation, Ikenna E. Ifekaonwu

College of Graduate Studies: Theses & Dissertations

In recent years, lightweight structures have become mature and adopted in various applications. The importance of quality assurance cannot be overemphasized hence extensive research has been conducted to assess the quality of lightweight structures. This study investigates a novel process that exploits motion magnification to investigate the damage characteristics of lightweight mission-critical parts. The goal is to assure the structural integrity of 3D printed structures and composite structures by determining the inherent defects present in the part by exploiting their vibration characteristics. The minuscule vibration of the structure was recorded with the aid of a high-speed digital camera, and the …

Microstructural And Chemical Characterization Of A Purple Pigment From A Faiyum Mummy Portrait, Glenn Gates, Yaqiao Wu, Jatuporn Burns, Jennifer Watkins, Darryl P. Butt

Materials Science and Engineering Faculty Publications and Presentations

Results are presented from analyses that were conducted to explain the presence of chromium, detected noninvasively using energy-dispersive X-ray fluorescence (XRF), in the unusually large (2-3mm diameter) rough gem-like purple pigment particles in the paint used for a Faiyum mummy portrait. An approximately 50 μm diameter particle of the chromium-containing purple pigment was extracted from the Portrait of a Bearded Man, dated to Roman Imperial Egypt in the second century, circa 170-180 CE, accession #32.6 in the Walters Art Museum collection. The particle was characterized using energy-dispersive X-ray fluorescence analysis, electron microscopy, diffraction, and atom probe tomography. It is …

Influence Of The Inas Coverage On The Performance Of Submonolayer-Quantum-Dot Infrared Photodetectors Grown With A (2×4) Surface Reconstruction, Ahmad Alzeidan, Tiago F. De Cantalice, Kevin D. Vallejo, Paul J. Simmonds, Alain A. Quivy

Materials Science and Engineering Faculty Publications and Presentations

Two infrared photodetectors based on submonolayer quantum dots, having a different InAs coverage of 35% and 50%, were grown, processed and tested. The detector with the larger coverage yielded a specific detectivity of 1.13×10 ¹¹ cm Hz ^1/2 W ^-1 at 12K, which is among the highest values reported in the literature for that kind of device.