Materials Science and Engineering Commons^™

Generation Of Excited Species In A Streamer Discharge, Shirshak K. Dhali

Electrical & Computer Engineering Faculty Publications

At or near atmospheric pressure, most transient discharges, particularly in molecular gases or gas mixture containing molecular gases, result in a space charge dominated transport called a streamer discharge. The excited species generation in such discharges forms the basis for plasma chemistry in most technological applications. In this paper, we simulate the propagation of streamers in atmospheric pressure N₂ to understand the energy partitioning in the formation of various excited species and compare the results to a uniform Townsend discharge. The model is fully two-dimensional with azimuthal symmetry. The results show a significantly larger fraction of the energy goes …

Printable Dielectric Elastomers Of High Electromechanical Properties Based On Sebs Ink Incorporated With Polyphenols Modified Dielectric Particles, Zhanxu Liu, Bangze Zhou, Chenchen Li, Yuhao Wang, Shipeng Wen, Yanfen Zhou, Liang Jiang, Fenglei Zhou, Tony Betts, Stephen Jerrams

Articles

In this work, a recently developed 3D additive processing technology termed electrohydrodynamic (EHD) printing was employed to fabricate dielectric elastomer (DE) films by using styrene-ethylene-butylene-styrene (SEBS) inks with the addition of high dielectric titanium dioxide (TiO2) nanoparticles. In order to improve the dispersibility of TiO2 in the SEBS matrix, extracted walnut polyphenols were utilized for surface modification of TiO2 nanoparticles labelled wp-TiO2. The effect of the applied voltage on the ink jet morphology of the obtained SEBS based inks during EHD printing was analyzed. The prepared films had precision patterned shapes and their morphology was studied. It revealed that the …

In Depth Characterisation Of The Biomolecular Coronas Of Polymer Coated Inorganic Nanoparticles With Differential Centrifugal Sedimentation, André Perez-Potti, Hender Lopez, Beatriz Pelaz, Abuelmagd Abdelmonem, Mahmoud G. Soliman, Ingmar Schoen, Philip M. Kelly, Kenneth A. Dawson, Wolfgang J. Parak, Zeljka Krpetic, Marco P. Monopoli

Articles

Advances in nanofabrication methods have enabled the tailoring of new strategies towards the controlled production of nanoparticles with attractive applications in healthcare. In many cases, their characterisation remains a big challenge, particularly for small-sized functional nanoparticles of 5 nm diameter or smaller, where current particle sizing techniques struggle to provide the required sensitivity and accuracy. There is a clear need for the development of new reliable characterisation approaches for the physico-chemical characterisation of nanoparticles with significant accuracy, particularly for the analysis of the particles in the presence of complex biological fluids. Herein, we show that the Differential Centrifugal Sedimentation can …

The Development Of A Holistic Quality Score Using In-Situ Monitoring Of Laser Powder Bed Fusion, Ryan Daigneault

College of Graduate Studies: Theses & Dissertations

Additive manufacturing processes allow for a great degree of flexibility in terms of part production. The process is autonomous once the part has started printing in that the operator generally does not need to intervene until the part is finished. One issue that this introduces, however, is an inability to determine part quality during the printing process. Once a part has started printing, the operator must either wait until the part is finished or regularly check on the part during the print to determine the part quality. Using data gathered from multiple sensors, a quality score can be used to …

A Kinetic Evaluation For Phenothiazine Base Copolymers, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

In here, the non-isothermal decomposition kinetics of co-polymers-based phenothiazine was present-ed. For this, firstly, 3, 7-di-2-thienyl-10H-phenothiazine (TF) was prepared via an optimized Suzu-ki–Miyaura cross-coupling reaction. After monomer (TF) characterization, the copolymerization re-actions with EDOT and thiophene were performed by the electrochemical technique. The molecular masses of the co-polymers were found by gel permeation chromatography (GPC) analysis. Thermal characterizations of the resulting polymers were conducted by thermogravimetric analyses. The thermal decomposition kinetics of the resulting polymers was also performed. For this, the kinetic methods (Tang, FWO, KAS, Kissinger, and Friedman) based on the multiple heating rates were used. Several kinetic parameters …

Inorganic Biodegradable Substrates For Devices & Systems, Chang-Soo Kim, Richard K. Brow, Delbert E. Day

Patents

Disclosed are biodegradable glass substrates that are useful as functional elements of solid-state devices. In particular, biodegradable glass substrates having a rapidly degradable glass and a slowly degradable glass provide a structural platform that completely dissolves following a desired operational lifetime of devices such as implanted electronic devices, implanted sensor devices, and optical fibers.

Degradation Issues And Stabilization Strategies Of Protonic Ceramic Electrolysis Cells For Steam Electrolysis, Hanrui Su, Yun Hang Hu

Michigan Tech Publications, Part 1

Protonic ceramic electrolysis cells (PCECs) are attractive electrochemical devices for converting electrical energy to chemicals due to their high conversion efficiency, favorable thermodynamics, fast kinetics, and inexpensive materials. Compared with conventional oxygen ion-conducting solid oxide electrolysis cells, PCECs operate at a lower operating temperature and a favorable operation mode, thus expecting high durability. However, the degradation of PCECs is still significant, hampering their development. In this review, the typical degradations of PCECs are summarized, with emphasis on the chemical stability of the electrolytes and the air electrode materials. Moreover, the degradation mechanism and influencing factors are assessed deeply. Finally, the …

Reclamation Of Fused Silica From Investment Shells Used For Casting Steel, Samuel L. Holt

College of Graduate Studies: Theses & Dissertations

Fused silica is widely used for investment casting shell molds. Fused silica shells are discarded after being used for casting one time. This is due to the transformation of fused silica to beta cristobalite above 1652℉ (900℃). To reduce cost and waste of investment casting foundries, this study is exploring a method to inhibit transformation of fused silica and reclaim it from high temperature investment casting shells. This research has employed firing to minimalize fused silica transformation to cristobalite. The phase transformation is minimalized due to sintering and coarsening of the particles during firing. Coarsening reduces surface area to volume …

Mechanical Properties Of Nanomodified Hybrid Gfrp Composite Materials, Micah Rop Kimutai

College of Graduate Studies: Theses & Dissertations

The mechanical behavior of the nanomodified hybrid epoxy matrix was investigated in glass fiber reinforced plastics (GFRP). In this study, five nanocomposites enriched with as received halloysite, nanomer I.28E, HNT-APTES, and the hybrid combinations of the two HNTs with the nanomer I.28E were successfully fabricated. To evaluate the effects and morphological characteristics of the individual fillers and the hybrid configurations on the epoxy resin matrix, TGA, DSC, and DMA were analyzed. To understand the effect of the five configurations on the neat GFRP laminate, mode I interlaminar fracture toughness, tensile, and vibration properties were investigated. Electron microscopy testing techniques were …

The Effects Of Molybdenum, Chromium, And Niobium On Gray Iron For Brake Rotor Applications, Matthew Hasbrouck

Dissertations, Master's Theses and Master's Reports

Brake rotor composition and microstructure must be optimized for thermal and mechanical performance to avoid thermal-mechanical cracking, excessive wear, and to reduce noise. Niobium is an element that increases the strength and wear resistance of gray iron; however, the interaction of niobium with other common alloying elements (chromium and molybdenum) is not well understood. Thirteen gray cast iron alloys were produced with varying levels of carbon equivalent (CE), Cr, Mo, and Nb. Bars with four different diameters (8, 14, 22, and 30 mm) were cast from each alloy and microstructural and physical properties such as graphite flake morphology, pearlite spacing, …

Role Of Eta Phase Evolution On Creep Properties Of Nickel Base Superalloys Used In Advanced Electric Power Generation Plants, Ninad Mohale

Dissertations, Master's Theses and Master's Reports

Advanced fossil energy power generation plants require materials that withstand high temperatures and corrosive environments. One such material that is used in steam turbines is Nimonic 263. It is a nickel-base superalloy that is principally strengthened by gamma primephase (Ni₃(Ti, Al)) and has an L1₂structure. At extended times and at turbine operating temperatures however, eta (Ni₃Ti) phase is known to form at the expense of gamma prime. Eta has a complex DO₂₄structure and is the stable phase between 750°C and 900°C, but with slow kinetics of formation. Little is understood about eta …

Analyzing Variation In Dispersoid Formation In Aluminum Alloys By Minor Changes In Homogenization Temperature, Brendan Treanore

Dissertations, Master's Theses and Master's Reports

The homogenization of billets in the aluminum extrusion industry is a critical step that removes chemical segregation from casting, dissolves low melting point phases, forms nanoscale dispersoid phases, and promotes the beta to alpha transformation of iron particles in the matrix. With ever increasing use of aluminum extrusion in the automotive industry there is a constant need for increased efficiency and consistency in processing of extruded aluminum. The work in this thesis explores the effects of 10°C differences in the homogenization temperature on the formation of dispersoids in 6082 alloys used in the automotive industry. The role of dispersoids is …

Effect Of Random Pinning On Nonlinear Dynamics And Dissipation Of A Vortex Driven By A Strong Microwave Current, W.P.M.R. Pathirana, Alex Gurevich

Physics Faculty Publications

We report numerical simulations of a trapped elastic vortex driven by a strong ac magnetic field H(t)=Hsinωt parallel to the surface of a superconducting film. The surface resistance and the power dissipated by an oscillating vortex perpendicular to the film surface were calculated as functions of H and ω for different spatial distributions, densities, and strengths of pinning centers, including bulk pinning, surface pinning, and cluster pinning. Our simulations were performed for both the Bardeen-Stephen viscous vortex drag and the Larkin-Ovchinnikov (LO) drag coefficient η(v) decreasing with the vortex velocity v. The local residual surface resistance R_i(H) …

Thermophysical Properties Of Nominally Phase Pure Boride Ceramics, Austin D. Stanfield

Doctoral Dissertations

"This research focusses on the thermophysical properties of nominally phase pure boride ceramics. As interest in ultra high temperature ceramics increases due to a renewed interest in hypersonic flight vehicles and with the expanding materials design space accompanying interest in high entropy materials, it is imperative to understand the intrinsic properties of boride ceramics. By reducing Hf content in ZrB₂ from the natural abundance, ~1.75 at% in this case, to ~100 ppm, thermal conductivity increased from 88 W/m·K to 141 W/m·K. Removal of Hf allowed the thermal conductivity of ZrB₂ with small transition metal solute additions to be …

Effects Of Corrosion On The Sers Activity And Optical Response Of Silver Nanorods, Christopher J. Mealer

UNF Graduate Theses and Dissertations

The nanoscience and nanotechnology community have a common goal in better understanding the surfaced enhanced Raman scattering (SERS) that occurs due to laser plasmon resonance in conjunction with metal enhanced substrates. Metallic nanostructures, such as silver (Ag) nanorods, are widely used in biological and chemical sensing applications that rely on the measurement of subtle changes in the optical response of the nanostructures in the presence of a target agent. The optical response of Ag nanorods and most other metallic nanostructures is highly sensitive to morphology and surface chemical termination. In pristine condition, the optical properties of Ag nanorods and other …

The Investigation Of The Underlying Microstructure Associated With Fracture Features In 6061 Cold Sprayed Aluminum, Justin White

UNF Graduate Theses and Dissertations

Cold gas dynamic spraying commonly known as cold spray is a process currently used for restoration, re-tolerancing, and application of coatings. With additional resources allocated towards the development of a through process model aimed at predicting the properties of bulk material produced via the Cold Spray process, more lab testing and investigation must be done to capture the effects of the varying microstructure in CS materials. The properties of ultra-fine-grained materials are derived from data collected from coarse grained materials and processes that do not accurately capture the effects as elevated strain rates and ultra-fine-grained materials. The lack of property …

Viability Of A Proposed Transparent Fluid Model For Analog Metal Casting Filling Process, Andres Segura Irazoqui

Dissertations and Theses @ UNI

This research work was conducted to develop a proposed transparent fluid model to mimic dross formation and dispersion in metal castings during the mold filling process. The major cause for dross formation includes the air entrainment, surface turbulence, and bubbles, which create oxide films inside the molten metal. The oxide films are trapped inside the casting after solidification causing detrimental effects on the mechanical properties of the casting.

The objective of the investigation was to explore the feasibility using phenolic urethane as a transparent fluid material to investigate air entrainment mechanism. The experimentation consists of the following materials: the phenolic …

Semi-Empirical Modeling Of Liquid Carbon's Containerless Solidification, Philip C. Chrostoski

Doctoral Dissertations

“Elemental carbon has important structural diversity, ranging from nanotubes through graphite to diamond. Previous studies of micron-size core/rim carbon spheres extracted from primitive meteorites suggest they formed around such stars via the solidification of condensed carbon-vapor droplets, followed by gas-to-solid carbon coating to form the graphite rims. Similar core/rim particles result from the slow cooling of carbon vapor in the lab. The long-range carbon bond-order potential was used to computationally study liquid-like carbon in (1.8 g/cm³) periodic boundary (tiled-cube supercell) and containerless (isolated cluster) settings. Relaxations via conjugate-gradient and simulated-annealing nucleation and growth simulations using molecular dynamics were …

Thermal And Mechanical Properties Of Novel Carbide Materials, Evan Charles Schwind

Doctoral Dissertations

"This research focuses on studying the thermal and mechanical properties of novel carbide materials at room and elevated temperatures. The novel carbide materials investigated include zeta phase tantalum carbide (ζ-Ta₄C_3-x) and a high entropy (Ta,Hf,Nb,Zr)C carbide. The electrical resistivity and thermal conductivity of zeta phase tantalum carbide (~96 wt.%) were measured as 160 ± 4.2 μΩ-cm and 9.6 W/m•K. These are higher and lower (respectively) than for cubic tantalum carbide, most likely due to planes of carbon vacancies present in the ζ-Ta₄C_3-x crystal structure. The thermal conductivity of (Ta,Hf,Nb,Zr)C was lower than any …

ผลของความหยาบผิวของโลหะผสม Ti-6al-4v ที่ขึ้นรูปด้วยวิธีการพิมพ์สามมิติต่อลักษณะทางสัณฐานวิทยาของท่อนาโนไทเทเนียมไดออกไซด์และความต้านทานการกัดกร่อน, ปาณิสรา พุทธสุวรรณ

Chulalongkorn University Theses and Dissertations (Chula ETD)

นอกจากวัสดุไทเทเนียมจะนิยมนำมาใช้เป็นวัสดุทดแทนกระดูกหรือข้อต่อที่เสียหายเนื่องจากมีสมบัติที่ดีในเรื่องของความแข็งแรงสูง มีความต้านทานการกัดกร่อนสูงและมีความเข้ากันได้ทางชีวภาพแล้ว การสร้างท่อนาโนไทเทเนียมไดออกไซด์ก็ใช้กันอย่างแพร่หลายในการปรับสภาพผิววัสดุเช่นกัน เนื่องจากช่วยส่งเสริมการยึดเกาะของเซลล์และให้การตอบสนองของเซลล์ได้ดีกว่าพื้นผิวโลหะเอง แม้มีการศึกษาหลายชิ้นได้รายงานความสัมพันธ์ระหว่างท่อนาโนไทเทเนียมไดออกไซด์กับอัตราการเชื่อมประสานของเซลล์ แต่อย่างไรก็ตามอัตราการกัดกร่อนของชั้นท่อนาโนไทเทเนียมไดออกไซด์ภายใต้สภาวะการใช้งานนั้น ๆก็มีความจำเป็นที่ต้องศึกษาเช่นกัน ในงานนี้เราได้ศึกษาผลจากการปรับสภาพผิวที่ถูกเตรียมด้วยเงื่อนไขต่าง ๆ ต่อพฤติกรรมการกัดกร่อนของวัสดุ Ti-6Al-4V และลักษณะทางสัณฐานวิทยาของชั้นท่อนาโนไทเทเนียมไดออกไซด์ซึ่งการศึกษาจะแบ่งเป็น 2 กลุ่มคือกลุ่มที่ทำการปรับสภาพผิวด้วยการขัดและกลุ่มที่ทำการปรับสภาพผิวด้วยการขัดต่อด้วยการแอโนไดซ์ โดยจะทำการวัดความหยาบพื้นผิวที่เตรียมได้ก่อนการแอโนไดซ์โดยเครื่องวัดความหยาบผิวและศึกษาลักษณะพื้นผิวหลังแอโนไดซ์ด้วยกล้องจุลทรรศน์อิเล็กตรอนแบบส่องกราดและศึกษาพฤติกรรมการกัดกร่อนในสารละลายฟอตเฟสบัฟเฟอร์ซาลีนโดยเทคนิคโพเท็นชิโอไดนามิกโพลาไรเซชัน ผลการวิจัยชี้ให้เห็นว่าก่อนการแอโนไดซ์ความหยาบผิวที่เตรียมได้ไม่มีความสัมพันธ์กับอัตราการกัดกร่อนโดยตรง แต่อย่างไรก็ตามหลังจากแอโนไดซ์พบว่าความหยาบผิวตั้งต้นจากการเตรียมผิวก่อนแอโนไดซ์มีผลต่อลักษณะการเกิดท่อนาโนไทเทเนียมไดออกไซด์ รวมถึงอัตราการกัดกร่อนมีความสัมพันธ์กับขนาดเส้นผ่านศูนย์กลาง ค่าส่วนเบี่ยงเบนมาตรฐานของขนาดเส้นผ่านศูนย์กลางท่อและลักษณะการเรียงตัวของท่อที่เกิดขึ้น