Materials Science and Engineering Commons^™

Mechanical Performance Of Woven Carbon Reinforced Epoxy Composites With Varied Orientation Angle, Sweety Ashish Agrawal, Someshwar Bhattacharya

Journal of Metals, Materials and Minerals

The mechanical properties of woven carbon fibre reinforced epoxy composites laminated with different orientation angle in stacking sequence were investigated. Woven fabric layers with different linear density carbon tow have been produced on modified rigid rapier sample loom and impregnated with epoxy by hand lay-up technique for composite preparation. Curing of composite was carried out at room temperature for 2 h. Five different laminar composites were prepared with different orientation angles [(0/0/0/0), 0/+30/-30/0, 0/+45/-45/0, 0/+60/-60/0 and 0/+90/-90/0]. The mechanical properties like tensile, flexural, and impact test) were analysed in both longitudinal and transverse directions. Physical properties such as density and …

Investigation Of Optimum Parameters For Rotary Friction Welding Of Aluminum Round Bars Using Three-Level Factorial Design Methodology, Tanakorn Jantarasricha, Siridech Kunhirunbawon, Montri Wimol

Journal of Metals, Materials and Minerals

The welding process has been essential to increasing productivity in numerous industries across Thailand. There are several welding processes to choose from, and the welding process to use will be determined by the suitability of the production in that industry. Another important consideration in welding is to keep the mechanical properties of the joint area as close to the parent material workpiece as possible. This research aims to select the optimum parameter for rotary friction welding aluminum round bar AA6063-T5. That is according to the DIN 50125 type B standard test. The optimal condition consists of welding rotational speed, welding …

Synthesis And Optical Properties Of Forsterite Ceramic Pigments Using Mirror Wastes As A Flux, Niti Yongvanich, Natchaya Lithira, Nitchakarn Nuniead, Wanchalerm Chauyarsa

Journal of Metals, Materials and Minerals

Cobalt-doped forsterite ceramic pigments based on the formula (Mg2-2xCo2x)SiO4 (x = 0, 0.05, 0.1, 0.2) were synthesized using mirror wastes as a flux. Addition of this flux enhanced forsterite phase formation at lower temperature by as much as 200℃. The resulting pigment particles were in a micron range which is suitable for use in a ceramic glaze. The host structure (Mg2SiO4) could accommodate cobalt cations up to 20 at%. Investigation on the chemical distribution revealed that no chemical species from the flux reacted with pigment grains. Optical properties were examined by UV-vis spectroscopy and colorimetry. Technical performance of the obtained …

Deformation Manifold Learning Model For Multi Walled Carbon Nanotubes, Shashank S. Pathrudkar

Dissertations, Master's Theses and Master's Reports

Two-Dimensional (2D) materials are being studied widely by researchers due to their superior material properties over the bulk materials. Since the isolation of graphene in 2004, graphene has gained popularity amongst the 2D materials community. Graphene when rolled into sheets form Carbon Nanotubes (CNTs) which possess excellent mechanical and electrical properties. Concentric stacks of CNTs yield Multi-walled Carbon Nanotubes (MWCNTs) which are superior to CNTs in certain aspects. It has been well established that the deformation of CNTs and MWCNTs change their mechanical and electrical properties significantly. This has opened doors for CNTs into numerous applications and also piqued the …

Investigation Of The Tribological Behavior Of Mineral Lubricant Using Copper Oxide Nano Additives, Ahmed A. Abdel-Rehim, Sayed Akl, Sherif Elsoudy

Mechanical Engineering

In this study, tribological properties of custom formulated and stabilized nano lubricant are investigated. Spherical CuO nanoparticles are suspended in 20W-50 mineral base lubricant using Oleic Acid (OA) as a surfactant. Three different nano lubricant concentrations with 0.2, 0.5, and 1 wt.% were analyzed through ASTM G-99 pin-on-disc tribometer standardized test under boundary/mixed lubrication regimes. The generated friction and wear analyses confirm a consolidation of tribological properties with a reduction in friction coefficient in the range of 14.59–42.92%, compared with the base lubricant. Analysis of worn surfaces (SEM/EDX) as well as (AFM) was conducted. Combined hypotheses were proposed from the …

Modeling And Optimization Of Process Parameters In Face Milling Of Ti6al4v Alloy Using Taguchi And Grey Relational Analysis, Al Mazedur Rahman, S M Abdur Rob, Anil K. Srivastava

Manufacturing & Industrial Engineering Faculty Publications

Titanium alloys are extensively used in aerospace, missiles, rockets, naval ships, automotive, medical devices, and even the consumer electronics industry where a high strength to density ratio, lightweight, high corrosion resistance, and resistance to high temperatures are important. The machining of these alloys has always been challenging for manufacturers. This article investigates the combined effect of radial depth, cutting speed and feed rate on cutting forces, tool life, and surface roughness during face milling of Ti6Al4V alloy. This study focuses on the significance of radial depth of cut on cutting force, tool life and surface roughness compared to that of …

Recovery Of Phosphorus From Florida Phosphatic Waste Clay, Amir Eskanlou

Graduate Theses, Dissertations, and Problem Reports (ETD)

This MS thesis examines the recovery of phosphorus (P) from Florida waste clay (WC). A comprehensive literature review revealed that: (i)-The most important values being lost to WC are P and rare earth elements (REEs). For the recovery of these values from WC, two crucial attempts are the removal of extremely fine-sized clays, followed by the recovery of phosphate content, which can pave the path for the recovery of REEs; (ii)-Any scientific/ technological solution should, at the same time, be economically and environmentally attractive to the industry. As such, moving from mostly chemical separation processes to the primarily physical/ physicochemical …

Metal Supported Solid Oxide Fuel Cell Using Proton Conducting Electrolyte For Direct Ammonia Utilization, Edwin Vega Hiraldo

Graduate Theses, Dissertations, and Problem Reports (ETD)

Transportation represents about 27% of global warming greenhouse gas emissions nowadays. To reduce these emissions, fuel cell electric vehicles have been poised to be a new trend to provide zero-emission transportation. Among them, solid oxide fuel cells (SOFCs) offer efficient, clean energy, especially when powered by carbon-free fuel, such as ammonia. To enable onboard ammonia-fed SOFCs, a metal-supported, proton-conducting SOFC is investigated in this study. The metal support would provide physical robustness for thermal shock during vehicles’ quick start-up and shutdown, reduce internal temperature gradients due to the greater thermal conductivity of the metal, and enable conventional metal joining for …

Timber Bridge Pile Splicing With Fiber Reinforced Polymer Wraps, Drew L. Damich

Graduate Theses, Dissertations, and Problem Reports (ETD)

Timber pile repair using splicing is widely used but little research has been done to determine their strength capacity after repair using this method. Current timber pile splicing mechanisms utilize various steel or wooden components. Fiber Reinforced Polymer (FRP) wraps can be utilized as replacement to conventional materials in splicing of timber piles. This study evaluated the strength capacities of traditional splicing mechanisms in relation to FRP wrap splice mechanisms. Traditional splicing mechanisms consisted of flat steel plate, C-channel steel plate, and wooden plate splices. The FRP wrap splice consisted of unidirectional glass/epoxy composite with three layers of fabric as …

Development Of Synthetic Coal Char Simulant For Microwave Conversion Studies: A Computationally-Driven Approach, Kevin A. Hager

Graduate Theses, Dissertations, and Problem Reports (ETD)

Recent experimental demonstration of new reaction windows for coal char/methane reactions that are less energy-intensive, provides innovation for modular reactors. However, the correlation of the exact mechanism for the enhancement of these reaction windows is not certain. This study investigates the simplification of these experimental studies by developing a well-characterized coal char simulant. The approach involves using a computational approach to screen macroscopic composition to replicate the dielectric and compositional response of actual char. This study is focused on PRB coal char. A discrete element method (DEM) technique was used to simulate the packing of coal chars to give the …

Dry Reforming Of Methane Using Microwave Irradiated Metal Oxide/Coal Char Catalysts, Anthony Carter

Graduate Theses, Dissertations, and Problem Reports (ETD)

This research focuses on the synthesis of both shaped and amorphous powder materials, the combination of these materials with dried Powder River Basin (PRB) coal char, and their reactionary properties with methane and carbon dioxide gasses with conventional and microwave (MW) heating. The first goal of this project was to synthesize shaped micro and nano sized particles with ideal dielectric properties for converting electromagnetic energy into heat and proven capabilities of activating methane. These particles were synthesized via solvothermal, hydrothermal, and co-preceptory treatments alone and onto the surface of dried PRB coal char. PRB is a sub-bituminous, low-ranking coal (LRC) …

Improving Performance And Durability Of Intermediate Temperature Proton‐Conducting Solid Oxide Electrolysis Cells Via Materials Design And Catalyst Surface Engineering, Hanchen Tian

Graduate Theses, Dissertations, and Problem Reports (ETD)

Solid oxide steam electrolysis cell, a promising electrical-chemical conversion device for the next generation efficient hydrogen production and energy storage, has been actively studied because of their high energy conversion efficiencies and prospective applications as electrochemical reactors. After decades of research on protonic ceramic materials, remarkable advances have been made in the protonic ceramic electrochemical cells (PCECs) air electrode and electrolyte. However, the existing air electrodes are far from satisfying the requirements of practical applications, a series of issues, including the lack of active and durable electrodes, greatly limit the commercialization. To date, the systematic development of triple conducting catalysts …

Molecular To Macroscopic Understanding Of Chloroaluminate Anion Intercalation In Rechargeable Aluminum-Graphite Batteries, Jeffrey Xu

Dissertations and Theses

Today’s global energy challenges pose an urgent need to electrify transportation and better store intermittent renewable energy sources (e.g., solar and wind energy). For such large-scale battery applications, aluminum batteries are a promising “beyond lithium-ion” technology due to the high volumetric capacity, earth abundance, low-cost, and inherent safety of aluminum metal. However, there are very few compatible positive electrode materials that exhibit high energy density and cycling stability, in part due to the challenges of electrochemically intercalating highly charged Al³⁺ cations. Recently, graphite has been demonstrated as a promising positive electrode material in non-aqueous rechargeable aluminum batteries, which store …

Development Of Light Actuated Chemical Delivery Platform On A 2-D Array Of Micropore Structure, Hojjat Rostami Azmand, Hojjat Rostami Azmand

Dissertations and Theses

Localized chemical delivery plays an essential role in the fundamental information transfers within biological systems. Thus, the ability to mimic the natural chemical signal modulation would provide significant contributions to understand the functional signaling pathway of biological cells and develop new prosthetic devices for neurological disorders. In this paper, we demonstrate a light-controlled hydrogel platform that can be used for localized chemical delivery in a high spatial resolution. By utilizing the photothermal behavior of graphene-hydrogel composites confined within micron-sized fluidic channels, patterned light illumination creates the parallel and independent actuation of chemical release in a group of fluidic ports. The …

Novel Design And Facile Synthesis Of Functional Nanostructures For Energy And Environmental Application, Zhuojun Wang

Wayne State University Theses

Environmental pollution and energy crisis are two of the major obstacles in the development of a more sustainable society. It is an interesting but technically challenging task to design novel methods for the facile and scalable synthesis of multifunctional materials for applications in both energy storage and environmental remediation. In this thesis, I tried to design and synthesize novel nanostructured materials for energy and environmental applications, achieved highly promising results. I developed a facile electrochemical approach to synthesize the zinc oxide with the zinc element for photocatalytic reactions. It demonstrated dramatically improved performances in degradation of organic pollutant in water, …

Microstructural Development Of Inconel 625 Nickel-Based Superalloy As Function Of Laser Powder Bed Fusion Parameters, Sofia Nucci

Electronic Theses and Dissertations, 2020-2023

Additive manufacturing (AM) allows fabrication of complex components with features that are impractical or impossible to achieve through conventional methods. Selective laser melting (SLM) powder bed fusion AM technology was selected for this study on Inconel 625, a widely utilized high-temperature alloy that is hard to machine. The present work investigates impact of laser power and scanning speed variations on the resulting characteristics of fabricated IN625 samples. Gas atomized metallic alloy powders were acquired and analyzed through laser diffraction to verify acceptable size distribution. Cubic samples were built with a range of laser scan speeds in 200 mm/s intervals for …

Investigation Of Cation Exchange Behaviors Of FaXMa1-XPbl3 Films Using Dynamic Spin Coating, Hyang Mi Yu, Byeong Geun Jeong, Dae Young Park, Seong Chu Lim, Gon Namkoong, Mun Seok Jeong

Applied Research Center Publications

In this study, we fabricated and characterized uniform multi-cation perovskite FA_xMA_1−xPbI₃ films. We used the dynamic spin-coating method to control the cation ratio of the film by gradually increasing the FA+, which replaced the MA+ in the films. When the FA+ concentration was lower than xFA ~0.415 in the films, the stability of the multi-cation perovskite improved. Above this concentration, the film exhibited δ-phase FAPbI₃ in the FA_xMA_1−xPbI₃ films. The formation of δ-phase FAPbI₃ disturbed the homogeneity of the photoluminescence spatial distribution and suppressed the absorption spectral bandwidth …

Mechanical Activation And Cation Site Disorder Of Spinel-Based Ceramics, Cole A. Corlett

Masters Theses

"This research focuses on the processing and the effects that has on the cation disorder of magnesium-aluminate spinel based (MgAl₂O₄) ceramics. The first goal of this project was to determine the effects of high-energy milling, i.e., mechanical activation, on cation disorder (inversion) within the spinel structure. First, 1:1 molar ratios of MgO:Al₂O₃ ceramics were processed using two green processing methods, ball milling (XD) and SPEX milling (mechanical activation, MA) followed by a subsequent annealing treatment in air to form a single spinel phase in each powder sample. Neutron diffraction analysis was employed to …

Toward Understanding Commercial Additives For Zincate Electrogalvanizing, Margaret Scott

Masters Theses

"Cyanide zinc electrogalvanizing has been used for many years to produce high quality and uniform zinc coatings. Due to toxicity concerns, a significant amount of research has occurred to remove the use of cyanide while still producing a similar deposit. One of the resulting plating chemistries is the alkaline zincate bath.

Alkaline zincate plating has the advantages of low startup cost, low toxicity, and low corrosion rate. Despite these advantages, alkaline bath conditions do not produce acceptable zinc deposits without the use of plating additives, which can promote lustrous, smooth deposits. This research aims to: (1) generate fundamental electrochemical data …

การเตรียมบล็อกปูทางเท้าพรุนน้ำจากเศษเซรามิกโดยใช้เคลือบเซรามิกเป็นวัสดุเชื่อมประสาน, พิมพ์รัมภา กิติธรากุล

Chulalongkorn University Theses and Dissertations (Chula ETD)

ปัญหาน้ำท่วมขังหลังจากที่เกิดฝนตกหนัก มักเป็นปัญหาใหญ่สำหรับพื้นที่ในเขตเมืองหลวง ซึ่งส่งผลกระทบโดยตรงกับผู้คนที่สัญจรบนท้องถนน การนำบล็อกพรุนที่มีความสามารถในการระบายน้ำได้มาใช้ทำเป็นพื้นสำหรับทางเดินสามารถแก้ไขปัญหาดังกล่าวได้ โดยทั่วไปแล้วบล็อกพรุนที่มีความสามารถในการระบายน้ำที่สูงมักจะทำให้ค่าความแข็งแรงต่ำ เนื่องจากมีรูพรุนอยู่ในโครงสร้างของชิ้นงานมาก ดังนั้นในงานวิจัยนี้จึงสนใจนำเศษเซรามิกเนื้อสโตนแวร์ ที่แตกหักเสียหายจากอุตสาหกรรมเซรามิกประเภทเครื่องใช้บนโต๊ะอาหารที่ผ่านการบดและคัดขนาด 2 - 5 มิลลิเมตร มาใช้เป็นมวลรวมหยาบสำหรับการทำบล็อกพรุนและเลือกใช้เคลือบเซรามิกขาวทึบมาเป็นวัสดุเชื่อมประสาน โดยใช้กระบวนการขึ้นรูปด้วยมือในแม่พิมพ์ และได้ศึกษาปัจจัยที่ส่งผลต่อสมบัติทางกายภาพของบล็อกพรุน พบว่ามีปัจจัยหลัก 4 ที่ส่งผลต่อสมบัติทางกายภาพของบล็อกพรุน ได้แก่ อุณหภูมิที่ใช้ในการเผาบล็อกพรุน อัตราส่วนระหว่างมวลรวมและวัสดุเชื่อมประสาน ขนาดของเศษเซรามิกที่ใช้เป็นมวลรวม และความเข้มข้นของเคลือบที่ใช้เป็นวัสดุเชื่อมประสาน นอกจากนี้ยังได้หาเงื่อนไขที่เหมาะสมต่อการขึ้นรูปบล็อกพรุนที่ให้อัตราการไหลซึมผ่านของน้ำและค่าความแข็งแรงที่เหมาะสม ซึ่งพบว่าบล็อกพรุนปูทางเท้าที่ประกอบด้วยเศษเซรามิกขนาด 2 – 5 มิลลิเมตร ปริมาณร้อยละ 80 โดยน้ำหนัก วัสดุเชื่อมประสานปริมาณร้อยละ 20 โดยในวัสดุเชื่อมประสานประกอบด้วยสัดส่วนผงเคลือบแห้งต่อน้ำ ร้อยละ 71.43 : 28.57 โดยน้ำหนัก และเผาที่อุณหภูมิ 1200 °C ซึ่งให้ค่าความแข็งแรงต่อแรงอัดที่ 24.57 MPa ความหนาแน่น 1.64 g/cm3 ค่าความพรุนตัว 30.43% และอัตราการไหลซึมผ่านของน้ำ 897.74 L/m2·min