Power and Energy Commons^™

Optimisation Of Stand-Alone Hybrid Energy Systems For Power And Thermal Loads, Barun Kumar Das

Theses: Doctorates and Masters

Stand-alone hybrid energy systems are an attractive option for remote communities without a connection to a main power grid. However, the intermittent nature of solar and other renewable sources adversely affects the reliability with which these systems respond to load demands. Hybridisation, achieved by combining renewables with combustion-based supplementary prime movers, improves the ability to meet electric load requirements. In addition, the waste heat generated from backup Internal Combustion Engines or Micro Gas Turbines can be used to satisfy local heating and cooling loads. As a result, there is an expectation that the overall efficiency and Greenhouse Gas Emissions of …

Coupling Radio Frequency Energy Via The Embedded Rebar Cage In A Reinforced Concrete Structure For The Purpose Of Concrete Degradation Sensing, Ryan Campiz

UNF Graduate Theses and Dissertations

This study focuses on utilizing an energy harvesting system in which a dedicated Radio Frequency (RF) power source transmits RF power via rebar in a reinforced concrete column. The RF power is received and decoupled by a receiver, and is then rectified, boosted, and stored as electrical energy in a supercapacitor, later to be used to make measurements, process data, and communicate to the source via rebar. Two design attempts are presented in this study: (a) one uses single line conduction at 2.4 GHz for RF power transfer; (b) the other uses a more conventional two-line conduction at 8.0 kHz …

A Novel Power Sharing Control Method For Distributed Generators In Dc Networks, Christina James

Electrical & Computer Engineering Theses & Dissertations

The power sharing control method is a desirable solution to integrate multiple renewable energy generators into the grid and to keep them working synchronously. Power sharing control between different distributed generators is an important consideration for the stabilized operation of the power grid network. In this thesis work, a novel method is used with the concept of droop control technique and is designed to control power from each individual generator in DC network particularly. The proposed power sharing control method can be widely applied to grid connected network and to islanded power grid network for obtaining high efficiency of power …

Understanding The Impact Of Large-Scale Power Grid Architectures On Performance, Ange-Lionel Toba

Engineering Management & Systems Engineering Theses & Dissertations

Grid balancing is a critical system requirement for the power grid in matching the supply to the demand. This balancing has historically been achieved by conventional power generators. However, the increasing level of renewable penetration has brought more variability and uncertainty to the grid (Ela, Diakov et al. 2013, Bessa, Moreira et al. 2014), which has considerable impacts and implications on power system reliability and efficiency, as well as costs. Energy planners have the task of designing infrastructure power systems to provide electricity to the population, wherever and whenever needed. Deciding of the right grid architecture is no easy task, …

Research Of Sustainable Jet Fuel Production Using Microbes, Rajee Olaganathan

Publications

Global climate change, coupled with rapidly increasing oil prices and energy demand around the world, has paved a way for intense research in the biofuel sector. Stakeholders in the aviation industry have started to focus on bio-jet fuel. Bio-jet fuel is regarded as a sustainable solution to greenhouse gas emissions and energy demand. This paper provides a brief review of the biofuel production technologies, the role of bacteria in producing hydrocarbons and the recent advancements in microbial engineering to enhance the biofuel production. Finally, this paper concludes by highlighting the challenges and future research implications in bio-jet fuel production.

Grey Wolf Optimization-Based Optimum Energy-Management And Battery-Sizing Method For Grid-Connected Microgrids, Kutaiba Sabah Nimma, Monaaf D. A. Al-Falahi, Hung Duc Nguyen, S. D. G. Jayasinghe, Thair Mahmoud, Michael Negnevitsky

Research outputs 2014 to 2021

In the revolution of green energy development, microgrids with renewable energy sources such as solar, wind and fuel cells are becoming a popular and effective way of controlling and managing these sources. On the other hand, owing to the intermittency and wide range of dynamic responses of renewable energy sources, battery energy-storage systems have become an integral feature of microgrids. Intelligent energy management and battery sizing are essential requirements in the microgrids to ensure the optimal use of the renewable sources and reduce conventional fuel utilization in such complex systems. This paper presents a novel approach to meet these requirements …

Impact Of Inrush Currents And Geomagnetically Induced Currents On Transformer Behavior, Nishchal Sharma

Dissertations, Master's Theses and Master's Reports

Transformers are the tie-points of electrical power systems. Their protection from power system faults and other innate issues is of prime importance. A few of the issues that are studied in this report are magnetic inrush currents, geomagnetically induced currents in power transformers and Over-excitation.

This project develops a novel way of initializing and visualizing the flux linkage in the transformer core for studies on energization inrush currents. In addition, a quasi-DC source for GIC has been developed in order to study the GIC effects on power transformers and a sensitivity analysis has been carried out to understand effects of …

Active And Reactive Power Control Of Flexible Loads For Distribution-Level Grid Services, Jingyuan Wang

Dissertations, Master's Theses and Master's Reports

Electric vehicle (EV) charging/discharging can take place in any P-Q quadrants, which means EVs could provide reactive power at any state-of-charge (SOC). This dissertation shows four-quadrant operation of EVs and aggregation of EVs for support of grid operations.

First, this work develops hierarchical coordination frameworks to optimally manage active and reactive power dispatch of number of spatially distributed EVs incorporating distribution grid level constraints. This work demonstrates benefits of coordinated dispatch of active and reactive power from EVs using a 33-node distribution feeder with large number of EVs (more than 5,000). Case studies demonstrate that, in constrained distribution grids, coordinated …

Energy Storage Control And Requirements For Inverter-Based Microgrids, Mehrzad Mohammadi Bijaieh

Dissertations, Master's Theses and Master's Reports

The intermittent nature of distributed renewable sources such as wind or solar requires integration of energy storage systems. In this dissertation a distributed form of the Hamiltonian Surface Shaping and Power Flow Control (HSSPFC) method is used to determine the energy storage requirements of three-phase inverter-based microgrids. The overall control is appropriate to be integrated into a hierarchical control system. As the primary control, a novel dq droop control sets the local references and is supported by a level-zero Hamiltonian controller which includes energy storage feed-forward and feedback, and an inverter feed-forward controls. Here, the energy storage element performs as …

Preparation Of Nis2 Nanosheet And Its Application In Asymmetric Supercapacitor, Yuan-You Wang, Ya-Nan Liu, Dang-Qin Jin

Journal of Electrochemistry

In this work, the NiS₂ nanosheets have been synthesized using Ni(OH)₂  as a precursor through a sacrificial template method. The microstructure and chemical composition of as-prepared NiS₂ were characterized by XRD, EDS, BET, SEM and TEM techniques. The results showed that both Ni(OH)₂  and NiS₂  were composed of nanoplates. The electrochemical tests revealed that NiS₂ exhibited the high specific capacitance of 1067.3 F•g^-1 at a current density of 1 A•g^-1 and excellent rate performance. Furthermore, in order to evaluate the practical application of NiS₂, an asymmetric supercapacitor, NiS₂ as …

Electroactivities Of Pd/Fe3O4-C Catalysts For Electro-Oxidation Of Methanol, Ethanol And Propanol, Tao Zou, Qing-Feng Yi, Yuan-Yuan Zhang, Xiao-Ping Liu, Guo-Rong Xu, Hui-Dong Nie, Xiu-Lin Zhou

Journal of Electrochemistry

Development of palladium (Pd) catalysts with high electroactivity for alcohol oxidation is significant for alcohol fuel cells. In this work, Pd nanoparticles were formed by sodium borohydride (NaBH₄) reduction method and subsequently deposited on the surface of carbon supported ferriferrous oxide (Fe₃O₄/C) composites to obtain the Pd/Fe₃O₄-C catalysts with different Fe₃O₄ loadings. Their transmission electron microscopic (TEM) images show that the Pd nanoparticles were uniformly dispersed on the Fe₃O₄/C. Electroactivities of the prepared Pd/Fe₃O₄-C catalysts toward oxidations of C1-C3 …

Kinetics And Mechanism Toward Electrochemical Reductions Of Sodium Bromide And Methanol Over Iron Electrodes, Qun Liao, Shu-Feng Zhang, Wen-Hua Leng

Journal of Electrochemistry

It is of technological value and scientific interest to the electro-synthesis of ferrocene, conversion of carbon dioxide (CO₂) and organic electro-synthesis in non-aqueous solutions by investigating the kinetics and mechanism toward electrochemical reductions of sodium bromide (NaBr) and methanol over iron electrodes. However, few reports in the related researches are available. In this article, the kinetics and mechanism toward electrochemical reductions of NaBr and methanol over iron electrodes were examined in detail by carrying out the polarization curve and electrochemical impedance spectroscopic measurements. The results showed that methanol was the reactant, while Na⁺ ions were functioned only …

Effect Of Peg-Coating On Properties Of Lithium-Sulfur Battery Cathode Material Containing Carbon Fiber Conductive Agent, Jie-Cheng Tan, Yan-Hong Tian, Xue-Jun Zhang, Kai-Le Fan

Journal of Electrochemistry

The composite materials contained high modulus carbon fiber (HMCF) were successfully prepared by employing a ball-milling process based on the coating treatment of polyethylene glycol (PEG), and their structures and morphologies were characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) techniques．The influences of PEG content on sulfur cathode capacity, cycle stability and rate performance were systematically studied. It was found that by the pre-coating of PEG, the cathode exhibited the high initial discharge specific capacity of 1312.5 mAh⋅g^-1 at a current rate of 0.2C, and the reversible discharge capacity of 650 mAh⋅g …

Capacity Fading Analyses Of Lini0.5Co0.2Mn0.3O2And Lini0.5Co0.2Mn0.3O2/Lifepo4 Cathode Materials For Lithium-Ion Battery, Yi Hu, Xiang-Zhu He, Zhong-De Deng, Ling-Yong Kong, Wei-Li Shang

Journal of Electrochemistry

The LiNi _0.5Co _0.2Mn _0.3O₂/LiFePO₄ (NMC532/LFP) composite cathode material for lithium-ion battery was prepared by wet ball-milling. The capacity fading behaviors of LiNi _0.5Co _0.2Mn _0.3O₂ (NMC532) and LiNi _0.5Co _0.2Mn _0.3O₂/LiFePO₄ (NMC532/LFP) were analyzed by X-ray diffraction (XRD), scanning electron microscope (SEM), charge/discharge and electrochemical impedance spectroscopy (EIS) tests. The results indicated that the capacity retention values of NMC532/LFP were 97.80% and 86.48%, respectively, after 50 cycles and 60℃ high temperature storage. The NMC532/LFP exhibited better cycle performance and high temperature storage performance. …

Cobalt-Based Nitrogen-Doped Carbon Non-Noble Metal Catalysts For Oxygen Reduction Reaction, Meng-Xiu Jiang, Jing Zhang, Yue-Hua Li, Rong Zhang

Journal of Electrochemistry

Transition metal-nitrogen co-doped carbon catalysts have attracted significant attention because of their reasonable activity and remarkable selectivity toward oxygen reduction reaction (ORR) as cathodic reaction in fuel cells. However, the role of transition metal in the active sites of the catalysts still is uncertain. In this work, the Co_x-N_y/C-T catalysts were prepared with BP2000 as a carbon source, urea (Ur) as a nitrogen source and Co(OAc)₂•4H₂O as a metal precursor by a simple chemical method. Meanwhile, in order to optimize the ORR activity, the catalysts were synthesized with different amounts of Co …

Core-Shell Pd@Pt Ultrathin Nanowires As Durable Oxygen Reduction Electrocatalysts, Xin Wang, Yun-Jie Xiong, Liang-Liang Zou, Qing-Hong Huang, Zhi-Qing Zou, Hui Yang

Journal of Electrochemistry

This paper describes a simple CO-assisted reduction approach for the controllable synthesis of ultrathin Pd nanowires along the one-dimensional (1D) direction. Ultrathin Pt films from one to several atomic layers were successfully decorated onto ultrathin Pd nanowires by utilizing Cu UPD deposition, and followed by in-situ redox replacement reaction of UPD Cu by Pt. The core–shell structure and composition of the Pd@Pt ultrathin nanowires have been verified using transmission electron microscopy and energy dispersive X-ray spectrometry. The core–shell Pd@Pt ultrathin nanowires exhibited comparative electrocatalytic activity and improved durability for the oxygen reduction reaction in comparison with commercial Pt black. The …

Effects Of Jet Milling And Classifying Process On The Performance Of Lifepo4/C In Full Batteries, Xing-Liang Liu, Mao-Ping Yang, Wei-Wei Wang, Yong Cao

Journal of Electrochemistry

The carbon coated lithium iron phosphate (LiFePO₄/C) composite cathode material was prepared by using iron phosphate process. The effects of jet milling and classifying process on the electrochemical performance of LiFePO₄/C cathode material in full batteries were investigted. Scanning electron microscopic analyses suggested that the globose secondary particles were crustily crushed during the jet milling and classifying process, which would further result in lower tap density and carbon content. The LiFeP₄/C composite cathode materials with different physical characteristics were further tested in full batteries to evaluate the electrochemical properties. The results showed no obvious …

Engineering The Electrochemical Capacitive Properties Of Activated Carbon By Correct Selection Of Ionic-Liquid Electrolytes, Qiu-Hong Zhang, Bao-Shou Shen, Song-Lin Zuo, Xin-Yu Wei

Journal of Electrochemistry

In order to improve the electrochemical capacitive properties and to apply coconut shell activated carbon (AC) serving as electrode materials in ionic liquid (IL)-based supercapacitor (SC), the coconut shell AC material was re-activated using a steam as an activating agent in this work, forming a secondary AC (W-AC). The results showed that the specific capacitance of the W-AC electrode was much larger than that of the raw activated carbon electrode (R-AC) in 1-ethyl-3-methylimidazolium tetrafluoroborate ([EMIM]BF₄). The electrochemical techniques including cyclic voltammetry (CV), galvanostatic charge/discharge (GCD) measurement, and electrochemical impedance spectroscopy (EIS) were used to systematically study the capacitive …

Applications Of N-Methyl-N-Butyl-Pyrrolidinium Bromide And N-Methyl-N-Ethyl-Pyrrolidinium Bromide In Zn-Br Flow Batteries, Qi Zhang, Miao-Miao Zhang, Lin Meng

Journal of Electrochemistry

It is extremely important for battery performance and safety in Zn-Br flow battery to use quaternary ammonium salts as complex agents for bromine. In this work, the effects of electrolyte compositions and concentrations on the electrode reactions and battery performances were studied in the absence and presences of N-methyl-N-ethyl-pyrrolidinium bromide (MEP) or N-methyl-N-butyl-pyrrolidinium bromide (MBP). The conductivities in the electrolytes containing different constitutions and concentrations were measured by EIS method. The charge-discharge performance for the battery and the complex ability for bromine in different electrolytes were also investigated. The results showed that the electrolyte containing MBP was better than that …

Effect Of Fe2+/Fe3+Interconvertion On Reduction Behavior Of Fe3+ In Acidic Electrolytes, Jian-Xin Qin, Feng Lin, Wen-Ping Liu, Chao Chen, Meng-De Ren

Journal of Electrochemistry

The influences of ferrous/ferric (Fe²⁺/Fe³⁺) interconvertion on electrochemical reduction and electrode reaction of Fe³⁺ were investigated by using linear sweep voltammetry, potentiostatic method and cyclic voltammetry (CV) in acidic electrolytes containing chloride ion (Cl^-) and sulfate ion (SO₄^2-). It was shown that the reduction process of Fe³⁺/Fe²⁺ would take place in two independent stages: (1) the reduction of Fe³⁺ to Fe²⁺ at E=0.35V and (2) the co-precipitation of Fe²⁺ by forming Fe(OH)₂ (E≤-0.3 V) instead of Fe. The major effect of Fe^{2+ …}