Power and Energy Commons^™

Junction Temperature Estimation Of Silicon Carbide Power Module Using Internal Gate Resistance As Temperature Sensitive Electrical Parameter, Michael Sykes

Graduate Theses and Dissertations

The junction temperature of a power module is measured non-intrusively and uninterrupted in its application by analyzing the dependency of gate resistance to temperature. The circuit configuration proposed consists of altering the gate loop path and adding a basic peak detection circuit with an added low-pass filter to accurately measure the small differences seen during a temperature change on the internal gate resistance. The testing on this Silicon Carbide power module shows that the internal gate resistance has a positive temperature coefficient. This causes the current and the voltage drop on the gate loop sensing resistance to reduce as the …

Analysis And Optimization Of The Two-Phase Series Capacitor Buck Dc-Dc Converter, Salahaldein Ali Aboajila Ahmed

Graduate Theses and Dissertations

Current sharing schemes for conventional multi-phase converters are based on sensing each phase current to deliver the current information to their controllers. In conventional buck converters, this fact may require a preset current sharing ratio at the expense of efficiency, which eventually requires a larger sensing circuit to achieve the sensing accuracy of each phase. Introducing the concept of automatic current sharing is one of the solutions to tackle this issue. Automatic current sharing (Current Sharing Mechanism CSM) is an advanced way to distribute heat generation in multi-phase switching topologies at full load. A two-phase series capacitor buck converter (2-pscB) …

High Power Density And High Efficiency Converter Topologies For Renewable Energy Conversion And Ev Applications, Dereje Lemma Woldegiorgis

Graduate Theses and Dissertations

This dissertation work presents two novel converter topologies (a three-level ANPC inverter utilizing hybrid Si/SiC switches and an Asymmetric Alternate Arm Converter (AAAC) topology) that are suitable for high efficiency and high-power density energy conversion systems. The operation principle, modulation, and control strategy of these newly introduced converter topologies are presented in detail supported by simulation and experimental results. A thorough design optimization of these converter topologies (Si/SiC current rating ratio optimization and gate control strategies for the three-level ANPC inverter topology and component sizing for the asymmetric alternate arm converter topology) are also presented.

Performance comparison of the proposed …

Adjusting The Alloying Degree Of Pt3Zn To Improve Acid Oxygen Reduction Activity And Stability, Tian-En Zhang, Ya-Ni Yan, Jun-Ming Zhang, Xi-Ming Qu, Yan-Rong Li, Yan-Xia Jiang

Journal of Electrochemistry

Proton exchange membrane fuel cell (PEMFC) is a new type of energy device, a relatively excellent way to achieve carbon neutrality. However, due to the relatively slow reaction rate of oxygen reduction reaction (ORR) at the cathode, platinum (Pt) is the key material of the cathode catalyst. However, Pt is a kind of noble metal, and its high cost restricts the PEMFC commercialization process. At present, the main approach is to combine transition metals with Pt to prepare Pt-based alloys and to reduce the use of Pt. Pt-based alloys are excellent catalysts for ORR, improving both the activity and stability, …

Preparation Of Pt@Basrtio3 Nanostructure And Its Properties Towards Photoelectrochemical Ammonia Synthesis, Jing Zhang, Rui-Xia Guo, Jian-Jun Fu, Shi-Bin Yin, Pei-Kang Shen, Xin-Yi Zhang

Journal of Electrochemistry

Ammonia is an important industrial raw material and a potential green energy. Using renewable energy to convert nitrogen into ammonia under ambient condition is an attractive method. However, the development of efficient photoelectrochemical ammonia synthesis catalysts remains a challenge. Perovskite such as BaSrTiO₃ (BST) is a good photocatalytic material. However, BST is active under ultraviolet light and has a high recombination rate of photogenerated electron-hole pairs. By dispersing precious metals, it can effectively regulate the absorption of sunlight by BST. In this work, we used a two-step method to prepare BST. The H₂PtCl₆·6H₂O …

Multi-Scale Simulation Revealing The Decomposition Mechanism Of Electrolyte On Lithium Metal Electrode, Yan-Yan Zhang, Yue Liu, Yi-Ming Lu, Pei-Ping Yu, Wen-Xuan Du, Bing-Yun Ma, Miao Xie, Hao Yang, Tao Cheng

Journal of Electrochemistry

Lithium metal is considered as an ideal anode material for next-generation high energy density batteries with its high specific capacity and low electrode potential. However, the high activity of lithium metal can lead to a series of safety issues. For example, lithium metal will continuously react chemically with the electrolyte, forming unstable the solid electrolyte (SEI) films. In addition, lithium dendrites can be formed during cycling, which can puncture the SEI film and cause short circuits in the battery. These drawbacks greatly hinder the commercial application of lithium metal. To solve the above problems, it is important to understand the …

Effects Of Electrode Shape On Lithiation Process Of Lithium-Ion Battery Electrodes, Shi-Wei Sun, Jian-Jun Nie, Yi-Cheng Song

Journal of Electrochemistry

This paper studies the influence of electrode shape on the lithiation process of lithium ion batteries. Both experimental observation and numerical simulation are employed to investigate the competitive interaction between the diffusion of lithium ions in both solid and liquid phases and the lithium intercalation reaction at the electrode surface. Experimental cells were prepared with the anode and cathode being placed parallel, leaving the latter embracing the former. An experimental device based on CCD camera was set up for in situ observation of electrode lithiation. The lithiation levels of the graphite anodes were estimated according to the observed color profile. …

Dc Microgrid Fault Detection Using Multiresolution Analysis Of Traveling Waves, Rudy Montoya

Mechanical Engineering ETDs

Fast detection and isolation of faults in a DC microgrid is of particular importance. Fast tripping protection (i) increases the lifetime of power electronics (PE) switches by avoiding high fault current magnitudes and (ii) enhances the controllability of PE converters. This thesis proposes a traveling wave (TW) based scheme for fast tripping protection of DC microgrids. The proposed scheme utilizes a discrete wavelet transform (DWT) to calculate the high-frequency components of DC fault currents. Multiresolution analysis (MRA) using DWT is utilized to detect TW components for different frequency ranges. The Parseval energy calculated from the MRA coefficients are then used …

Dc Microgrid Fault Detection Using Multiresolution Analysis Of Traveling Waves, Rudy Montoya

Mechanical Engineering ETDs

Fast detection and isolation of faults in a DC microgrid is of particular importance. Fast tripping protection (i) increases the lifetime of power electronics (PE) switches by avoiding high fault current magnitudes and (ii) enhances the controllability of PE converters. This thesis proposes a traveling wave (TW) based scheme for fast tripping protection of DC microgrids. The proposed scheme utilizes a discrete wavelet transform (DWT) to calculate the high-frequency components of DC fault currents. Multiresolution analysis (MRA) using DWT is utilized to detect TW components for different frequency ranges. The Parseval energy calculated from the MRA coefficients are then used …

Zero-Power Ac Current Sensor, Omar Aragonez

Mechanical Engineering ETDs

In this study, a magnetic piezoelectric cantilever powered AC current and frequency sensor is proposed. This paper covers the configuration of the experimental setup, finite element modeling of the magnetic coupling, and the optimal spatial location of the magnetic proof mass in relation to the wire for smart grid applications. Solid and stranded copper wires of various gauges were used and carried current up to 30A. The magnets act as a proof mass to lower the frequency while also coupling to the magnetic field generated by the current carrying wire. The frequency of the AC current produces a sinusoidal force …

Intra-Hour Solar Forecasting Using Cloud Dynamics Features Extracted From Ground-Based Infrared Sky Images, Guillermo Terrén-Serrano

Electrical and Computer Engineering ETDs

Due to the increasing use of photovoltaic systems, power grids are vulnerable to the projection of shadows from moving clouds. An intra-hour solar forecast provides power grids with the capability of automatically controlling the dispatch of energy, reducing the additional cost for a guaranteed, reliable supply of energy (i.e., energy storage). This dissertation introduces a novel sky imager consisting of a long-wave radiometric infrared camera and a visible light camera with a fisheye lens. The imager is mounted on a solar tracker to maintain the Sun in the center of the images throughout the day, reducing the scattering effect produced …

Foam-Based Floatovoltaics: A Potential Solution To Disappearing Terminal Natural Lakes, Koami Soulemane Hayibo, Joshua M. Pearce

Electrical and Computer Engineering Publications

Terminal lakes are disappearing worldwide because of direct and indirect human activities. Floating photovoltaics (FPV) are a synergistic system with increased energy output because of water cooling, while the FPV reduces water evaporation. This study explores how low-cost foam-based floatovoltaic systems can mitigate the disappearance of natural lakes. A case study is performed on 10%–50% FPV coverage of terminal and disappearing Walker Lake. Water conservation is investigated with a modified Penman-Monteith evapotranspiration method and energy generation is calculated with an operating temperature model experimentally determined from foam-based FPV. Results show FPV saves 52,000,000 m3/year of water and US$6,000,000 at 50% …

Forecast Of Community Total Electric Load And Hvac Component Disaggregation Through A New Lstm-Based Method, Huangjie Gong, Rosemary E. Alden, Aron Patrick, Dan Ionel

Power and Energy Institute of Kentucky Faculty Publications

The forecast and estimation of total electric power demand of a residential community, its baseload, and its heating ventilation and air-conditioning (HVAC) power component, which represents a very large portion of a community electricity usage, are important enablers for optimal energy controls and utility planning. This paper proposes a method that employs machine learning in a multi-step integrated approach. An LSTM model for total electric power at the main circuit feeder is trained using historic multi-year hourly data, outdoor temperature, and solar irradiance. New key temperature indicators, TmHAVC, corresponding to the standby zero-power operation for HVAC systems for summer cooling …

Aerial Radiation Detection Identification And Measurement System Detector Material Comparison Study, Benjamin C. Troxell, Kacey D. Mcgee, Christina L. Dugan

Faculty Publications

The 20th Chemical Biological Radiological Nuclear and Explosives Command (CBRNE) currently utilizes an airborne sodium iodide gamma and beta detection system to map radiation fields over large areas of interest. The 20th CBRNE explored emergent detector technologies utilizing two detection materials; thallium-activated cesium iodide and high purity germanium (HPGe). These detectors were simulated at various altitudes and compared to background measurements. The sodium iodide detector failed to provide isotopic discrimination at distance. The thallium-activated cesium iodide CsI(Tl) detector provided sufficient absolute efficiency and energy resolution to identify isotopics at distance. The HPGe detector provided the best energy resolution. However, current …

In Situ Characterization Of Electrode Structure And Catalytic Processes In The Electrocatalytic Oxygen Reduction Reaction, Ya-Chen Feng, Xiang Wang, Yu-Qi Wang, Hui-Juan Yan, Dong Wang

Journal of Electrochemistry

As an electrochemical energy conversion system, fuel cell has the advantages of high energy conversion efficiency and high cleanliness. Oxygen reduction reaction (ORR), as an important cathode reaction in fuel cells, has received extensive attention. At present, the electrocatalysts are still one of the key materials restricting the further commercialization of fuel cells. The fundamental understanding on the catalytic mechanism of ORR is conducive to the development of electrocatalysts with the enhanced activity and high selectivity. This review aims to summarize the in situ characterization techniques used to study ORR. From this perspective, we first briefly introduce the advantages of …

In-Situ/Operando57Fe Mössbauer Spectroscopic Technique And Its Applications In Nife-Based Electrocatalysts For Oxygen Evolution Reaction, Jafar Hussain Shah, Qi-Xian Xie, Zhi-Chong Kuang, Ri-Le Ge, Wen-Hui Zhou, Duo-Rong Liu, Alexandre I. Rykov, Xu-Ning Li, Jing-Shan Luo, Jun-Hu Wang

Journal of Electrochemistry

The development of highly efficient and cost-effective electrocatalysts for the sluggish oxygen evolution reaction (OER) remains a significant barrier to establish effective utilization of renewable energy storage systems and water splitting to produce clean fuel. The current status of the research in developing OER catalysts shows that NiFe-based oxygen evolution catalysts (OECs) have been proven as excellent and remarkable candidates for this purpose. But it is critically important to understand the factors that influence their activity and underlying mechanism for the development of state-of-the-art OER catalysts. Therefore, the development of in-situ/operando characterizations is urgently required to detect key intermediates along …

An Additive Incorporated Non-Nucleophilic Electrolyte For Stable Magnesium Ion Batteries, Mao-Ling Xie, Jun Wang, Chen-Ji Hu, Lei Zheng, Hua-Bin Kong, Yan-Bin Shen, Hong-Wei Chen, Li-Wei Chen

Journal of Electrochemistry

Non-nucleophilic electrolytes are promising next-generation highly stable electrolytes for magnesium-ion batteries (MIBs). However, a passivation layer on Mg metal anode usually blocks Mg²⁺ diffusion, leading to poor reaction kinetics and low Coulombic efficiency of the Mg plating/stripping in these electrolytes. Here we explore the utilization of phenyl disulfide (PDF) as a film-forming additive for non-nucleophilic electrolytes to regulate the interfacial chemistry on Mg metal anode. Phenyl-thiolate generated from the PDF additive was found to suppress the unfavorable surface blocking layer, resulted in a high Coulombic efficiency of up to 99.5% for the Mg plating/stripping process as well as a …

Synchrotron X-Rays Characterizations Of Metal-Air Batteries, Ya-Jie Song, Xue Sun, Li-Ping Ren, Lei Zhao, Fan-Peng Kong, Jia-Jun Wang

Journal of Electrochemistry

The rapid development of electric vehicles urgently requires high-energy-density batteries. Recently, metal-air batteries have attracted much attention in industry and academia for their ultra-high theoretical energy densities. However, the practical application of metal-air batteries is severely impeded by multiple drawbacks, including severe side reactions, low energy efficiency, and limited cycle life. Understanding the reaction mechanism of the cell and further developing effective strategies are beneficial for the practical application of metal-air batteries. In the past decade, advanced characterization techniques have accelerated the development of metal-air batteries. In particular, synchrotron radiation-based characterization techniques have been widely applied to the mechanistic study …

Encouraging Voluntary Government Action Via A Solar-Friendly Designation Program To Promote Solar Energy In The United States, Xue Gao, Casey I. Canfield, Tian Tang, Hunter Hill, Morgan Higman, John Cornwell

Engineering Management and Systems Engineering Faculty Research & Creative Works

Sustainable development requires an accelerated transition toward renewable energy. In particular, substantially scaling up solar photovoltaics (PV) adoption is a crucial component of reducing the impacts of climate change and promoting sustainable development. However, it is challenging to convince local governments to take action. This study uses a combination of propensity score matching (PSM) and difference-in-differences (DID) models to assess the effectiveness of a voluntary environmental program (VEP) called SolSmart that targets local governments to engage in solar-friendly practices to promote the local solar PV market in the United States. Via specific designation requirements and technical assistance, SolSmart simplifies the …

The Greenest Solar Power? Life Cycle Assessment Of Foam-Based Flexible Floatovoltaics, Koami Soulemane Hayibo, Pierce Mayville, Joshua M. Pearce

Electrical and Computer Engineering Publications

This study presents a life cycle analysis (LCA) of a 10 MW foam-based floatovoltaics (FPV) plant installed on Lake Mead, Nevada, U.S. A material inventory of the flexible crystalline silicon (c-Si)-based module involved massing and determination of material composition of the module's encapsulation layers with ATR/FTR spectroscopy and electron microscopy. The LCA was performed using SimaPro and the results were interpreted in terms of cumulative energy demands, energy payback time, global warming potential, GHG emissions, and water footprint including negative values for reduced evaporation. A sensitivity analysis was performed on the lifetime of the modules and the foam-based racking. The …