Power and Energy Commons^™

Current Tracking Power Supply For Sensor Calibration, Joshua Brookley

Electrical Engineering

This report highlights the steps taken to design and develop a constant 5V power supply capable of tracking load current. The background of its previous design, its necessary specifications and steps taken to achieve specifications are highlighted throughout the report. The report also contains conclusions and final recommendations for the design chosen, including its strengths and drawbacks.

Imu Integration To The Cal Poly Spacecraft Attitude Dynamics Simulator Power System, Wayland Chan

Electrical Engineering

The Cal Poly Spacecraft Attitude Dynamics Simulator mimics the rotation dynamics of a spacecraft in orbit and acts as a test bed for spacecraft attitude control system development and demonstration. Prior to this project, the simulator measured its attitude dynamics from a total of seven sensors mounted on to the platform, including three micro-electromechanical system (MEMs) gyroscopes, and four motor encoders. This project entails the installation of an LN-200 high performance gyroscope, which will provide a greater measure of accuracy. The goal of this project is to design a power circuit that will integrate the LN-200 inertial measurement unit onto …

Wireless Sensor Network For Energy And Environmental Monitoring: Helping Old Buildings Go Green, Jacob Power

Electrical Engineering

Today, the rising cost of energy and social trend of “going green” has put increasing pressure on commercial property owners to improve the efficiency of their investments.  There is good reason for this, too.  In the State of California, office buildings represent the single largest user of energy in the commercial sector.  This project consisted of the design, implementation, construction, testing, and deployment of a wireless sensor network for energy and environmental monitoring in retrofit commercial office installations.  The analyzed data generated by this system can be used by building management and owners to identify areas of inefficiency within the …

Design Strategy For A 3-Phase Variable Frequency Drive (Vfd), Omar David Munoz

Electrical Engineering

This paper describes the design processes for a 3-Phase Variable Frequency Drive (VFD) as broken up into two stages: The AC-DC converter and the DC-AC converter. It acknowledges three (3) design versions, all. The output of the motor drive is 3-phase pulse width modulation (PWM) ranging in possible operation frequencies from 0Hz to 13kHz. The frequency control circuit uses an Arduino Uno based of the ATMEGA 328p.

Off-Grid Public Lighting System – Design And Characterization Of An Led Luminaire, Quanghuy Le

Master's Theses

The technological advances made in the photovoltaic industry have led to a vast exploration of self-sustaining systems.  As the consumer demand for electricity rises from increasing population and development of existing technologies, new practices in system designs are required to relieve the impact on the electrical grid.

This thesis delves into a developing concept of using photovoltaic modules for roadway lighting, with emphasis on establishing the fundamental design for a “spot-lighting” luminaire.  By effectively extinguishing various sections of the luminaire in the absence of pedestrian trafficking, the proposed design and implementation will minimize the prolonged costs, as well as the …

Energy Harvesting From Exercise Machines: Forward Converters With A Central Inverter, Nicholas Keith Lovgren

Master's Theses

This thesis presents an active clamp forward converter for use in the Energy Harvesting From Exercise Machines project.  Ideally, this converter will find use as the centerpiece in a process that links elliptical trainers to the California grid.  This active clamp forward converter boasts a 14V-60V input voltage range and 150W power rating, which closely match the output voltage and power levels from the elliptical trainer.  The isolated topology outputs 51V, higher than previous, non-isolated attempts, which allows the elliptical trainers to interact with a central grid-tied inverter instead of many small ones.  The final converter operated at greater than …

Photovoltaic Emulator Adaptable To Irradiance, Temperature And Panel Specific I-V Curves, Joseph Gamos Durago

Master's Theses

This thesis analyzes the design and performance of a photovoltaic (PV) emulator. With increasing interest in renewable energies, large amounts of money and effort are being put into research and development for photovoltaic systems. The larger interest in PV systems has increased demand for appropriate equipment with which to test PV systems.

A photovoltaic emulator is a power supply with similar current and voltage characteristics as a PV panel. This work uses an existing power supply which is manipulated via Labview to emulate a photovoltaic panel. The emulator calculates a current-voltage (I-V) curve based on the user specified parameters of …

Programmable Household Led Light Fixture, Jordan Locano

Electrical Engineering

This report details the development and construction of a LED light fixture to be used for household lighting. This document details background information, design ideas, project specifications, production, assembly, testing, and conclusions involved with this project. The goals of this project is to design and build a cost-effective replacement for traditional room lighting that can perform better and last longer than traditional methods.

Solar Powered Electric Clothes Dryer, Roger Mai, Alan Swe

Electrical Engineering

Appliances that consume the most energy in a household usually involve heating, and an electric clothes dryer is one such appliance, consuming up to 4KW of power. The most environmentally friendly way is to hang clothes outside to dry, a natural solar and wind powered method, but unfortunately most people are unable to do so as some neighborhood communities do not allow the hanging of laundry outside as it is regarded as “unsightly”, for example. This project aims to provide an alternate solution to the wall-powered electric clothes dryer by designing one which operates entirely off the grid.

Bicycle-Powered Ac Generator, Andrew Austin

Electrical Engineering

The purpose of this senior project is to design, build, and be able to present a mechanism that will produce AC power using the mechanical energy produced by a person pedaling a standard bicycle. Also, I would like to be able to show the user and the audience the advantage of using compact fluorescent bulbs, and in doing so, make them more conscience of energy-saving products. To do this, I must present a stand that can support a bicycle with a rider, a way to convert the wheel’s motion to DC power, to convert that DC power to usable AC …

Portable Solar Desalination System, Genaro Sanchez, Alan Galarza, Erick Del Real

Electrical Engineering

Clean water and reliable energy can be difficult to obtain in remote locations such as desert villages, secluded islands, and other places where no fresh water can be found. The primary goal for this project is address these problems by implementing a portable desalinization plant system that is to be powered by solar energy PV system as the main energy source.

Sick Laser Scanner Power Supply For Use With A Yamaha Rmax Uav, Elliot Due

Electrical Engineering

No abstract provided.

Wind Power Generator Design For The Dc House Project, Evan Lim, Samson Liu

Electrical Engineering

The purpose of this project is to introduce a cost efficient alternative in converting wind into energy for third world countries.  Currently there are approximately 1.6 billion people who have limited access to electricity. As part of the DC House project, we hope to develop a solution for them as the use of electricity is becoming an essential part of life. One of the natural energy resources to provide power to the DC House is wind. The components used for the project are a DC motor and DC-DC converter to translate wind into power and produce DC voltage and current, …

Variable Dc Voltage Wall Outlet For The Dc House Project, Michael Detmers, Tyler J. Blauvelt

Electrical Engineering

This senior project report will focus on explaining the design and operation of a variable DC wall outlet for use in the DC house. Testing will include the use of various loads using different input DC voltages not exceeding a maximum output of 90W.

The most important aspects of the outlet are to have a highly-efficient converter efficiency as well as system isolation from the main DC bus on the input. This report will outline the purpose and way of achieving isolation through use of a Flyback DC-DC converter. The user interface is the second significant aspect and details of …

60 Watt Embedded Solar Cell Umbrella, Matthew Devoss

Electrical Engineering

No abstract provided.

Solar Instrumentation Lab, Rene Canedo Iii, Rong Gui Chen

Electrical Engineering

This project is a mobile platform that will allow experiments on different solar panels to be done easily while keeping the cost of the lab to a minimum. California Polytechnic State University’s motto is ‘learn by doing’ and this lab structure will allow students to get practical experience with photovoltaic cells and the instruments that are required to take measurements. The solar instrumentation lab is a potential hardware lab for the electrical engineering department’s Sustainable Electric Energy Conversion class EE 420 and Solar-Photovoltaic Systems Design EE 520. This group took the current solar structure as a base for the lab’s …

Cal Poly Power System Design & Analysis, Minesh D. Patel

Electrical Engineering

The scope of this project encompasses the design and analysis of the Cal Poly Power System at the distribution level using the SKM software environment. The purpose is to accurately model the power system in software so theoretical calculations and analysis can be executed. This requires sufficient preliminary research to obtain data for the main buildings on campus, sound interpretation of one line diagrams, designing the system within the software using realistic values and then performing analysis to model real world situations.  The data collected is under maximum load conditions for a specified time period using medium voltage parameters. The …

Exercise Bicycle Dc-Dc Converter For The Energy Harvesting From Exercise Machines Project, Ryan Rickard, Logan Stowe

Electrical Engineering

Project is a continuation of previous projects that seek an efficient DC to DC converter for the existing exercise bicycle system created by Mechanical and Electrical Engineering students. This DC-DC converter is to integrate with the wide range of DC voltages produced by the bicycle in order to produce a constant optimal voltage for charging a car battery. This converter will boost voltages when the bicycle outputs below the optimal voltage and buck voltages when above. The converter will take EHFEM one step closer to its overall and final goal of harvesting energy from the exercise machines in Cal Poly’s …

Brushless Dc Motor Design And Build, Justin Damele

Electrical Engineering

Complete Design and Build of a Brushless DC Motor. Everything was manufactured using various Lathes and End Mills. Everything built from scratch.

Dc House Modeling And System Design, Jessica E. Chaidez

Electrical Engineering

This project entails the study and design of DC power distribution for the DC House Project. Wire size, common high efficient loads, maximum power input, and different distribution system implementation (ring or radial) play a major role when designing an efficient, low-voltage distribution system. Efficiency is determined based on which main bus voltage powers all the loads with minimal power loss. Power efficiency is heavily dependent in DC-DC converter efficiencies due to the power loss in converting the voltage from high to low, or vice versa. Selection of the wire size plays a major role in power losses. There are …