Electrical and Computer Engineering Commons^™

Crack Detectability And Durability Of Coaxial Cable Sensors In Reinforced Concrete Bridge Applications, Genda Chen, Ryan D. Mcdaniel, Michael A. Brower, David Pommerenke

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The working mechanism and the measurement principle of topology-based crack sensors made of coaxial cables are briefly reviewed. The sensitivity, spatial resolution, and ruggedness of two coaxial cable sensors, respectively made of rubber and Teflon dielectric materials, were compared and validated with laboratory testing of a 4/5-scale, T-shaped, reinforced concrete beam-column specimen. Two Teflon sensors were installed on one of the solid decks of a three-span continuous highway bridge to investigate their durability and measurement repeatability. Laboratory tests indicated that both types of sensors have high sensitivity, but the Teflon sensor has a higher spatial resolution and a negligible spillover …

Optimization Of Inductively Coupled Plasma Dry Etching For Planar Waveguide Fabrication., Lim Weng Hong

Student Works (2010-2019)

Optimization of the Inductively Coupled Plasma (ICP) dry etching process parameters has been carried out. Seven main etching characteristics were considered in order to produce good etching quality. These characteristics are glass etching rates, selectivity of chromium to glass etching rate, channel side wall roughness, channel side wall vertical profile, channel cleanliness, critical dimension and resolution. Several ICP parameters that are affecting the etching characteristic were optimized in this work. These optimised ICP parameters obtained from this work are ICP power (880 W), bias power (45 W), operating chamber pressure (10 mtorr), reactant gas composition, reactant gas flow rate (35sccm …

Energy Reduction In Automotive Paint Shops A Review Of Hybrid/Electric Vehicle Battery Manufacturing, Claudia Patricia Arenas Guerrero

University of Kentucky Master's Theses

Automotive industry is facing fundamental challenges due to the rapid depletion of fossil fuels, energy saving and environmental concerns. The need of sustainable energy development has motivated the research of energy reduction and renewable energy sources. Efficient use of energy in vehicle manufacturing is demanded, as well as an alternative energy source to replace gasoline powered engines. In this thesis, we introduce a case study at an automotive paint shop, where the largest amount of energy consumption of an automotive assembly plant takes place. Additionally, we present a summary of recent advances in the area of hybrid and electrical vehicles …

Design And Evaluation Of An Audio-Frequency Transresistance Amplifier For Magnetic Tape Playback, Thomas R. Salvatierra

Browse all Theses and Dissertations

Analog magnetic tape remains a medium of choice for high-fidelity sound recording and reproduction. Some of this fidelity is sacrificed during the tape playback process; an optimized playback preamplifier is therefore critical to the performance of the medium. Existing playback methods integrate the voltage generated across the reproduce head to obtain a signal directly proportional to the remanent magnetic flux of the tape. An alternate playback method proposes the use of a transresistance amplifier to convert flux-proportional reproduce head current directly to voltage. This eliminates the need for voltage integration and minimizes the amount of equalization performed upon playback. Circuit …

The Harmonic Distortion Reduction Of Phase-Angle Fired Scrs Feeding A Resistive Load Using Fuzzy Logic, Matthew A. Clark

Browse all Theses and Dissertations

High power silicon controlled rectifiers (SCR) are used in the application of infrared radiation testing. A case study has been performed on a department of defense facility utilizing SCRs to transfer electrical energy to thermal energy. The facility is capable of generating up to 5000 °F across large cross-sectional areas, requiring tens of megawatts of power. The combination of high power, unbalanced loads, and SCR switching generate high harmonic disturbances that offer significant challenges for conventional linear control systems. In addition, unbalanced three-phase distribution systems are difficult to model, specifically during switching transients. Fuzzy logic is used to characterize the …

Development Of An Efficient Super-Resolution Image Reconstruction Algorithm For Implementation On A Hardware Platform, Pestak Thomas C.

Browse all Theses and Dissertations

There is a growing demand from numerous commercial and military applications for images with ever-improving spatial resolution. However, there are resolution-limiting factors inherent in all imaging systems. Decreasing pixel sizes and/or increasing sensor arrays are not always viable. Super-Resolution (SR) Image Reconstruction is an image processing technique that restores a high-resolution (HR) image from a series of low-resolution (LR) images of a particular scene. Recently, there has been extensive research on robust SR algorithms used for post-processing. The goal of this thesis is to explore the current SR research and design computationally efficient SR algorithms for real-time processing based on …

A Direction Finding System Using Log Periodic Dipole Antennas In A Sparsely Sampled Linear Array, Jonathan Andrew Weldon

Browse all Theses and Dissertations

This thesis explores the use of wide band log periodic dipole array (LPDA) antennas in direction finding systems. A wide band log periodic antenna will be constructed and tested to ensure hardware capability. A novel approach utilizing non-uniform spacing in a linear array will be used to improve the spatial resolution of the direction finding system. These specialized linear arrays are known as minimum redundancy or non-redundant linear arrays.

A Structured Asic Approach To A Radiation Hardened By Design Digital Single Sideband Modulator For Digital Radio Frequency Memories, Thomas B. Pemberton

Browse all Theses and Dissertations

Digital Radio Frequency Memories (DRFM) are widely used as modules in digital signal processing. These modules can provide several forms of signal manipulation and storage capabilities. With single event effects caused by environmental radiation the need for a radiation hardened DRFM is increased. Typical radiation hardening involves the use of specialized foundries utilizing proprietary CMOS libraries that are expensive to build or adding lead packages around a chip that is expensive and add weight to the chip. An alternative radiation hardening technique is to utilize a radiation hardened by design library. This library includes digital gates that have been hardened …

Frequency Domain Processing Based Chaos Communication For Cognitive Radio, Daniel Y. Sundersingh

Browse all Theses and Dissertations

Chaotic systems are deterministic non-linear dynamical systems which have intrinsic properties such as: irregularity, aperiodicity, and are impossible to predict over long periods of time. Cognitive radio on the other hand, has emerged recently as a powerful means to tackle the spectrum congestion problem. The goal of this thesis is to combine the benefits of the chaos communication system with the cognitive radio to create a robust, highly secure, flexible chaotic cognitive radio system. We first begin with a short survey of chaotic communication and cognitive radio technology. Then we compare chaotic waveforms to other conventional PN sequences and show …

Wideband, High Data Rate Ku-Band Modulator Driver Amplifier For High Reliability Spaceborne Applications, Jeremy D. Gassmann

Browse all Theses and Dissertations

The increased demand for high resolution satellite imagery for government, military, and commercial applications is driving the need for high data rate, millimeter-wave transmission systems to relay imagery information to a ground-based end user. An important aspect of this system which interfaces digital information to the RF domain is the modulator driver. The current trend in miniaturization of electronics leaves systems more vulnerable to single-event radiation effects in spaceborne applications. In an effort to overcome this deficiency, a wideband, high data rate modulator driver circuit has been designed, built, and tested using only high reliability space rated electronic components. To …

An Automated Approach To A 90-Nm Cmos Drfm Dssm Circuit Design, Thomas A. Hopkins

Browse all Theses and Dissertations

A digital single sideband modulator (DSSM) for a digital radio frequency memory (DRFM) was designed and implemented in a commercial 90-nm radiation-hardened-by-design (RHBD) structured ASIC by Thomas Pemberton in cite{Pemberton}. This thesis synthesized the same DSSM structure in a non-hardened 90-nm commercial process and compared the synthesis results of the two for power, delay, and area. The number of I/O bits and taps in cite{Pemberton} and this thesis were purposely made high to create a large target for radiation testing. As should be expected, the RHBD DSSM reported greater power and area. However, the RHBD power models were only estimates. …

Adaptive Thresholding For Detection Of Radar Receiver Signals, Stephen R. Benson

Browse all Theses and Dissertations

Digital microwave receivers play a critical role in many of today's modern radar tracking systems. The need for these digital receivers to push the boundaries in terms of bandwidth and input dynamic ranges (DR) is vital for their use in radar signal tracking. Significant research has been conducted in the area of the fast Fourier transform (FFT) to aid in continuing to enhance the performance capabilities of digital microwave receivers. However, with the advancement and increased complexity of these systems, the need for an efficient and effective adaptive thresholding technique is becoming ever more present.

The proposed adaptive thresholding technique …

Hyperspectral Methods Of Determining Grit Application Density On Sandpaper, Lee A. Clark

Browse all Theses and Dissertations

A low cost real time method of determining the density of grit applied to sandpaper does not currently exist. This thesis will explore three methods for determining grit density from digital image data. A means to characterize the application in terms of frequency by using direct cosine transform basis images will be explored. An RX detector algorithm to characterize the image background will be tested. A linear unmixing methodology will be developed that characterizes the proportion of glue and grit present in each hyperspectral pixel vector.

Sulfur-Tolerant Catalyst For The Solid Oxide Fuel Cell, Bozeman Joe Frank Iii

Browse all Theses and Dissertations

JP-8 fuel is easily accessible, transportable, and has hydrogen content essential to solid oxide fuel cell (SOFC) operation. However, this syngas has sulfur content which results in a poisonous hydrogen sulfide that degrades electrochemical activity and causes complete SOFC failure in some cases. The goal is to synthesize and verify a cost-effective, catalyst supported on cerium oxide that either stabilizes ionic conductivity in the presence of hydrogen sulfide and/or is highly sulfur-resistant. After thorough computational analysis, it was concluded that the platinum-copper skin catalyst was the most cost-effective, sulfur-resistant catalyst. Experimental synthesis of copper, platinum, and platinum-copper skin catalysts supported …

Fault Diagnosis Of Vehicular Electric Power Generation And Storage, Hithesh Sanjiva Uliyar

Browse all Theses and Dissertations

Automotive vehicles are becoming increasingly dependent on electric power, and this trend will accelerate. The health of the vehicular electric power generation and storage (EPGS) system is crucial to enhance vehicle safety, fuel economy, and customer satisfaction.

In this research, a state-of-health (SOH) monitoring method is developed for automotive EPGS system, focusing on alternator related faults. Parity relations, characterizing the correlation among EPGS system signals under normal operating conditions, are generated using principal/minor component analysis techniques. Based on a design of structured residuals, the faults under consideration, including shorted diodes, belt slippage, and regulator fault, are successfully detected and isolated. …

Design Of Ultra High Speed Flash Adc, Low Power Folding And Interpolating Adc In Cmos 90nm Technology, Vinayashree Hiremath

Browse all Theses and Dissertations

In recent years, signal processing has gained ample significance making high speed and low voltage analog-to-digital converters (ADC) inevitable in numerous applications. Two such ADCs designed in CMOS 90nm technology are presented in this thesis.

In flash ADC, thermometer to binary encoder often becomes bottleneck in achieving high speed. An encoder deploying new CMOS logic, with fewer transistors through the use of pseudo-dynamic circuits is described. This 4 bit flash ADC operates at 5GHz with an average power dissipation of 1.3mW.

Folding and interpolation significantly reduces the number of comparators used in flash architecture. A 6 bit 400MSPS low power …

Multi-User Signal Classification Via Cyclic Spectral Analysis, Brent Edward Guenther

Browse all Theses and Dissertations

This research develops and evaluates several different methods for multi-user signal classification via cyclic spectral analysis. The first method uses the spectral correlation function (SCF) through temporal smoothing with the use of higher order cyclic statistics (HOCS) to allow for modulation classification. The second method uses the cyclic temporal cumulant function (CTCF) and the spectral coherence function (SOF) through frequency smoothing. Using a feature-based pattern recognition technique with the SOF can not only determine the number of signals present in the received signal, but can also give signal parameter estimation and group classification performance. The last method conducts further modulation …

Design Of Hf Forward Transformer Including Harmonic Eddy Current Losses, Dhivya Ammanambakkam Nagarajan

Browse all Theses and Dissertations

Pulse Width Modulated (PWM) Forward DC-DC converter is a buck-derived isolated power converter which is used extensively in low power to medium power applications. Satisfactory operation of the transformer utilized in forward converter plays a crucial role in the overall operation of the forward converter. Hence detailed analysis pertaining to design of forward transformer is important. The forward transformer is unique as the magnetizing inductance is not required to store magnetic energy. Additionally, the forward transformer has a tertiary winding, which is required to reset the core and to prevent core saturation. This adds to the complexity of design and …

Characterization Of An Inductively Coupled Plasma Produced In Argon At 13.56 Mhz., Lim Ai Nuan

Student Works (2010-2019)

The electrical and plasma characteristics of radio frequency (13.56 MHz) inductively coupled argon plasma (RF ICP) were studied in this project. On the electrical breakdown properties, the breakdown voltage has a general appearance of Paschen’s curve and the minimum is achieved at 0.1 mbar. After ignition, two modes of discharge exist, namely, the E mode at low RF power and H mode at high RF power. Mode transition that occurs is accompanied by abrupt changes in both electrical and plasma characteristics. Hysteresis is observed in the mode transitions and has a minimum at 0.1 mbar. The resistance reflected into the …

Performance Analysis Of Srcp Image Based Sound Source Detection Algorithms, Praveen Reddy Nalavolu

University of Kentucky Master's Theses

Steered Response Power based algorithms are widely used for finding sound source location using microphone array systems. SRCP-PHAT is one such algorithm that has a robust performance under noisy and reverberant conditions. The algorithm creates a likelihood function over the field of view. This thesis employs image processing methods on SRCP-PHAT images, to exploit the difference in power levels and pixel patterns to discriminate between sound source and background pixels. Hough Transform based ellipse detection is used to identify the sound source locations by finding the centers of elliptical edge pixel regions typical of source patterns. Monte Carlo simulations of …