Electrical and Electronics Commons^™

Synthesis And Application Of Ceramic Paste For High-Temperature Electronic Packaging, Ardalan Nasiri

Graduate Theses and Dissertations

This dissertation research focused on the synthesis and application of ceramic paste for high-temperature applications. An alumina paste material comprising aluminum dihydric phosphate and alumina powder was developed for high-temperature electronic packaging. Nano aluminum nitride and nano-silica powders were embedded to promote the paste curing process, limit the grain growth, and increase its bond shear strength. The chip-to-substrate bond strength was enhanced and met the MIL-STD requirements for die-attach assembly. Its encapsulation property was improved with fewer cracks compared to similar commercial ceramic encapsulants. The die-attach material and encapsulation properties tested at 500°C showed no defect or additional cracks. Thermal …

Three-Event Energy Detection With Adaptive Threshold For Spectrum Sensing In Cognitive Radio Systems, Alexandru Martian, Mahmood Jalal Ahmad Al Sammarraie, Calin Vladeanu, Dimitrie Popescu

Electrical & Computer Engineering Faculty Publications

Implementation of dynamic spectrum access (DSA) in cognitive radio (CR) systems requires the unlicensed secondary users (SU) to implement spectrum sensing to monitor the activity of the licensed primary users (PU). Energy detection (ED) is one of the most widely used methods for spectrum sensing in CR systems, and in this paper we present a novel ED algorithm with an adaptive sensing threshold. The three-event ED (3EED) algorithm for spectrum sensing is considered for which an accurate approximation of the optimal decision threshold that minimizes the decision error probability (DEP) is found using Newton’s method with forced convergence in one …

Performance Analysis Of Renewable Energy Resources In Rural Areas: A Case Study Of Solar Energy, Jackson Justo

Tanzania Journal of Engineering and Technology (TJET)

This paper presents an overview of the recent development trends of solar photovoltaic (PV) systems and the performance in the Tanzanian context. The two types of solar power generation that are considered in this paper are: i) solar PV systems and ii) concentrated solar power (CSP). The two are compared in terms of cost of energy and energy storage mechanism. Moreover, the effect of ambient temperature on the solar PV module is analyzed. In addition, a detailed analysis on using solar axis tracking to increase the power generation is also presented. The extent to which the cell surface temperature and …

Modeling And Control Of Solar Pv With Battery Energy Storage For Rural Electrification, Irene Masenge

Tanzania Journal of Engineering and Technology (TJET)

In rural areas where electric power grid network is rarely available, power generation from renewable energy resource such as solar photovoltaic (PV) is mostly accomplished in standalone mode. The standalone solar PV system requires energy storage device to achieve reliable power supply to the end users. This paper presents modelling and coordination control of solar PV with battery energy storage system (BESS) for rural-electrification applications. The proposed control is accomplished via a bidirectional buck-boost converter with the objective of maintaining voltage at the DC bus constant. Simulation results based-on MATLAB/Simulink platform confirms good performance of the proposed system

Multipath Exploitation-Based Indoor Target Localization Model Using Single Marginal Antenna, Joseph Sisala

Tanzania Journal of Engineering and Technology (TJET)

Recently, indoor target localization became an area of interest due to its diverse applications. In indoor target localization, surrounding environment creates multipath components, which can be exploited to aid in localization process. A number of studies have been proposed to employ multipath exploitation in localizing indoor targets. However, their localization errors can still be improved. This study proposed a new localization model based on multipath exploitation techniques by using triangulation method. Ultra-wide band signals were resolved and associated using marginal antenna-based scheme. The estimate of the target location was then obtained using measured round-trip time delays. The location was determined …

Using Of Parametric Nonlinear Lc-Circuits In Stabilized Transducers Of The Number Of Phases, Ivan Mikhaylovich Bedritsky, Kamila Komilovna Jurayeva, Laziz Kholboboyevich Bozorov

Chemical Technology, Control and Management

The use of nonlinear circuits of an autoparametric nature with inductive and capacitive elements for obtaining the necessary phase shifts in single-phase-three-phase converters is considered. The amplitude-phase relations between the stresses of windings located on different rods of a three-core core are obtained. The conditions under which it is possible to stabilize the stresses of the artificial phases of the Converter, as well as the phase shifts between them, are shown.

Statistical Photo-Calibration Of Photo-Detectors For Radiometry Without Calibrated Light Sources Comprising An Arithmetic Unit To Determine A Gain And A Bias From Mean Values And Variance Values, Adrian M. Catarius, Nicholas Yielding, Stephen C. Cain, Michael D. Seal

AFIT Patents

Calibration of a radiometry system uses a readout circuit of a photo-detector to provide first and second measurements collected over first and second integration times, respectively, where the first and second measurements are related to a photonic input to the photo-detector by a gain and a bias. First mean and variance values are computed for a plurality of first measurements. Second mean and variance values are computed for a plurality of second measurements. The gain and bias are determined from the first and second mean values and the first and second variance values without the use of a calibrated source. …

Miso Dc-Dc Farmbot, Quyen Thi Nguyen, Brian Armijo, Astha Adhikari

Electrical Engineering

Making use of renewable energy directly from the location of production requires converting source power into usable power. The specific scope of this project focuses on the DC to DC conversion within a user friendly universal farmbot system. Since renewable sources vary widely in voltage and current, a wide input-range DC to DC converter is desired. Physical isolation, long lifespan, and adverse weather requires safe and reliable final product specifications. The goal of a very wide customer base drives the need for a product that does not require tinkering to get working, but to be usable out of the box …

Lawn Buddy, Jayson Johnston, Andrew Brown, Jacob Maljian

Electrical Engineering

Grass lawns are a common hallmark of the American home. In 2019, a survey from the National Association of Landscape Professionals found that 81% of all Americans owned a lawn [1]. Mowing is a time consuming and costly chore that is part of maintaining a grass lawn. The manual labor in mowing a lawn can exceed 40 hours per year [2]. People commonly incur weekly costs on mowing services to save time. Traditional gas powered mowers are physically demanding and use engines that need routine maintenance. They operate loudly enough that users should be wearing hearing protection and the noise …

The Characterization Of Effective Electromagnetic Fields On The Safety And Quality Of Low-Moisture Foods (Effs) - Prototype Device Development, Joe G. Sandoval

Electrical Engineering

Contamination of low-moisture foods including flour, wheat grain, baby formula, and more, have increasingly become a concern due to sanitizing challenges. While industrial food processors have long used RF heating to sanitize mass quantities, an equivalent consumer device is absent from the market today. The Characterization of Effective Electromagnetic Fields on the Safety and Quality of Low-Moisture Foods (EEFS) project is an interdisciplinary effort to develop an RF heating consumer device to sanitize low-moisture foods.

A prototype device was designed to sanitize low-moisture food items using RF heating acceptable for commercial or consumer applications.

Telemedicine: An Iot Based Remote Healthcare System., Mohammad Abdellatif, Walaa Mohamed

Electrical Engineering

This paper proposes a remote healthcare system which is referred to as Telemedicine. Telemedicine is a platform that establishes a connection be-tween the patient and the doctor. This platform belongs to the internet of medical things (IoMT) by enabling multiple medical sensors to connect to a server either using multiple communication technologies such as Wi-Fi, Bluetooth or GSM technologies. The system collects data from several sensors and sends them using one of the aforementioned technologies using an Arduino Board, while the inter-face is made with matlab and C#. Additionally, a comparative study between the three communications technologies used to connect …

Distance Estimation Using Ofdm Signals For Ultrasonic Positioning, Kyman Huang

Master's Theses

This paper describes a method of estimating distance via Time-of-Flight (TOF) measurement using ultrasonic Orthogonal Frequency Division Multiplexing (OFDM) signals. Using OFDM signals allows the signals and their sub-carriers to remain orthogonal to each other while continuously transmitting. This estimation method is based on the change of phase of a traveling wave as it propagates through a medium (air for ultrasonic signals). By using signals containing multiple tones, the phase change between each frequency component is slightly different. This phase difference is dependent on the distance traveled and can thus be used to estimate distance. This paper studies the impact …

Optimization Of Aggregated Ev Power In Residential Communities With Smart Homes, Huangjie Gong, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Electric vehicles (EVs) tend to increase peak power for residences in the evening when house owners return home and begin charging. The aggregated EV charging demand can cause a sudden rise in the peak power at the distribution system level, resulting in a “dragon curve” Such phenomenon, combined with the “duck curve” that is caused by high photovoltaic (PV) penetration in residential communities, requires fast ramping rates and expanded capabilities for local distribution transformers and main feeder cables provided by the utility. As a solution, a residential energy storage system (RESS) can store surplus PV generation during midday and use …

Raysun's Infrared Raisin Dryer, Lucas Kensinger, Saraith Aispuro, Joe Vanacore

General Engineering

The RaySuns senior project team was tasked with lowering the drying costs of raisins for River Ranch Raisins. In doing so, we explored several options for cutting costs: utilizing automation and exploring new drying technologies were our primary focus. We eventually planned a modular infrared heating mechanism which would be easy to automate in future projects. After manufacturing and testing an infrared heating mechanism, it was found that infrared drying could significantly cut costs versus the previous natural gas fired dryer tunnels while leaving room for automation. The infrared dryer was also shown to have the potential to create high-quality …

Rf Power Amplifier, Angel De Jesus Delgado, Rachanon Wajanakunakorn, Andrew John Ferguson

Electrical Engineering

Wireless devices are part of everyday life, cellphones and radio receivers impact more people than any piece of technology. Thus, the respective building blocks continue to advance and achieve better performance. A primary component of all wireless communication systems is the power amplifier that drives the antenna. The Institute of Electrical and Electronics Engineers (IEEE) holds the International Microwave Symposium (IMS) every year where teams compete internationally for the most efficient RF Power Amplifier (PA). Power amplifier technologies strive to maximize efficiency and linearity. Topologies to consider are D, E, F, F-1 and Doherty since they have a maximum theoretical …

Remedying Sound Source Separation Via Azimuth Discrimination And Re-Synthesis, Ruairí De Fréin

Conference papers

Commercially recorded music since the 1950s has been mixed down from many input sound sources to a two-channel reproduction of these sources. The effect of this approach is to assign sources to locations in a stereo field using a pan-position for each source. The Adress algorithm is a popular way of extracting individual music sound sources from a stereo mixture. A drawback of the Adress algorithm is that when time-frequency components in the stereo mixture are shared between two or more sources, calculating the inter-aural intensity scaling parameter for each source for that time-frequency component is challenging. We show how …

Power System Study For Oil And Gas Platform Connected To Onshore Grid, Taharim Rosshidi Hezrimi

Student Works (2020-2029)

Normally for oil and gas offshore platform, the electrical power supply is generated from the generator either using gas turbine generator, gas engine generator and diesel engine generator. The main power supply is backup by diesel engine generator in case emergency or during black start of the platform. As the design of oil and gas platform become complex, the size of generator keeps increasing. A new concept is being explored to mitigate this problem. Oil and gas company is looking to provide power generation from onshore and supplying the electrical power to a substation platform offshore and then distributed it …

High Speed, High Current Monitoring System, Nicolette Lila Ray

Electrical Engineering

Electronics testing requires lengthy data collection and analysis. Streamlining at least part of this process allows resource reallocation, and faster data processing. Verifying a signal’s efficiency is key specification for a component’s datasheet. This project focuses on streamlining data collection when measuring a device’s output current. It combines amplifier design and digital interfacing to perform monitor a device’s output current. A computer-enable interface displays a graphical output current representation. It ensures accurate, high speed, high current measurements while removing a person’s need to manually plot data after testing. A new testing method provides room for company and product growth with …

Fuzz Distortion Guitar Stompbox, James Dennis Cleary

Electrical Engineering

My Fuzz Distortion Pedal offers guitar players a full-fledged fuzz distortion pedal with gain, frequency cutoff and volume controls. The pedal offers a true bypass when inactive which allows the signal to pass through the effect with no coloration. The distortion pedal offers hard clipping of the input signal by amplifying it by a high amount, and then clipping the voltage of the signal through the use of diodes.

Conducted And Radiated Emi Measurements Of Parallel Buck Converters Under Varying Spread Spectrum Parameters, Elena Postupalskaya, Nathan Wang

Electrical Engineering

The Conducted and Radiated EMI Measurements with Parallel Buck Converters Under Varying Spread Spectrum Parameters research senior project aims to explore the effects from Spread Spectrum Frequency Modulation (SSFM) on the input electromagnetic interference (EMI) or noise of a switching power supply, specifically with LM53601MAEVM hardware. The input EMI is important as the main input bus needs to be clean to provide a reliable source for other sensitive devices connected to it. SSFM can replace a conventional EMI filter and save weight, space, and cost. This project provides a basis in terms of the impacts of variable SSFM in simulation …