Electrical and Electronics Commons^™

Electronic Profiling Of Synthetic Dna Using Schottky Junctions, Souhad M.A Daraghma

Student Works (2020-2029)

Deoxyribonucleic acid (DNA) has attracted a lot of attention lately owing to the discovery of its semiconducting property and is considered as an interesting material that could find applications in nanotechnology and electronic devices. In-depth understanding of its charge transfer mechanism is however required for effective development of DNA-based technology. This unfortunately remains still a non-trivial task despite the numerous theoretical and experimental studies that have been conducted to date. The complexity of the previously employed methods, and their lack of accuracy has made it difficult to grasp the clear understanding of the electronic behaviors of the DNA molecules under …

Multibeam Array Antenna For Base Station In The Fifth-Generation Mobile Communication System, Intan Izafina Idrus

Student Works (2020-2029)

Research on the fifth-generation (5G) mobile communication system has been accelerated to meet the standardization of the International Telecommunications Union for higher data traffic and higher data rates. The main requirements of the 5G mobile communication systems are the utilization of millimeter waves, the deployment of small cells, and the use of multibeam array antennas for multiple-input multiple-output schemes. Multibeam array antennas play an important role in developing a new base station to enhance system capacity, improve network coverage, and reduce co-channel interference. The main objective of this thesis is to design a single-layer multibeam array antenna at 28 GHz …

Conditional Generative Adversarial Network Demosaicing Strategy For Division Of Focal Plane Polarimeters, Garrett Sargent, Bradley M. Ratliff, Vijayan K. Asari

Electrical and Computer Engineering Faculty Publications

Division of focal plane (DoFP), or integrated microgrid polarimeters, typically consist of a 2 × 2 mosaic of linear polarization filters overlaid upon a focal plane array sensor and obtain temporally synchronized polarized intensity measurements across a scene, similar in concept to a Bayer color filter array camera. However, the resulting estimated polarimetric images suffer a loss in resolution and can be plagued by aliasing due to the spatially-modulated microgrid measurement strategy. Demosaicing strategies have been proposed that attempt to minimize these effects, but result in some level of residual artifacts. In this work we propose a conditional generative adversarial …

Evaluation Of Mechanical Properties Of Malaysia Local Source Wood For Electric Cruiser Board Applications, Mohamad Rosman Othaman

Student Works (2020-2029)

This research project revolves around the idea to reduce the carbon emission in mitigating the issue of climate change. An idea to introduce the electrical cruiser board by Muhammad Fiqkri Ismail from Universiti Kuala Lumpur with his idea to promote carbon less form of multimodal transportation for users in urban city of Greater Kuala Lumpur leads this research to study the elastic properties of local source woods in Malaysia that could be proposed for this application. The wood is used for the construction of the deck of cruiser board which designed three layers with the cross-ply laminate. Three types of …

Mechanical Alloying-Assisted Coating Of Fe–Al Powders On Steel Substrate, Alfian Noviyanto, Sri Harjanto, Wahyu Bambang Widayatno, Agus Sukarto Wismogroho, Muhamad Ikhlasul Amal, Nurul Taufiqu Rochman

Makara Journal of Technology

The coating layer of Fe–Al powders on the steel substrate was prepared by mechanical alloying at room temperature. Fe, Al, and the steel substrates were milled with high-energy ball milling for 32 h with a ball-to-powder ratio of 8 in an argon atmosphere to prevent oxidation during milling. Although mechanical alloying was performed for 32 h, no new phases were observed after mechanical alloying, as analyzed by X-ray diffraction. However, the crystallite size of the milled powders for 32 h decreased by factor two compared with the initial powders. Scanning electron micrographs showed that the coating layers formed >8 h …

Performance Of Free-Space Optical Communication Systems Using Optical Amplifiers Under Amplify-Forward And Amplify-Received Configurations, Ucuk Darusalam, Arockia Bazil Raj, Fitri Yuli Zulkifli, Purnomo Sidi Priambodo, Eko Tjipto Rahardjo

Makara Journal of Technology

With the growth of digital technology in the stage of industrial revolution 4.0, the demand for broadcasting large amounts of information to last mile users has increased. Free-space optical (FSO) communication is one of the telecommunication platforms that has shown immense potential in meeting the demand for information broadcasting. In this work, the performance of FSO communication based on wavelength division multiplexing with a data rate of 80 Gbps is investigated through simulations. The configuration of optical amplifiers in the FSO system is set up on the basis of the amplify-forward and amplify-received configurations to expand the network. The investigation …

Iso 9001:2015 Risk-Based Thinking: A Framework Using Fuzzy-Support Vector Machine, Ralph Sherwin A. Corpuz

Makara Journal of Technology

Risk-based thinking (RBT) is one of the distinct new features of the International Organization for Standardization 9001:2015. Interestingly, the standard does not prescribe any tools. Hence, organizations are puzzled as to the extent of conformance. Some organizations have adopted formal tools. However, these tools seem insufficient in linking the standard into an evidence-based decision support system. To resolve gaps in RBT implementation, this paper proposes a framework based on fuzzy inference system (FIS) and support vector machine (SVM) to automate risk analysis and evaluation, proposal and verification of action plans, and prediction of the feasibility of risks and opportunities according …

Influence Of The Shaping Process On The Tensile Properties Of Steel Reinforcement Bars Carbon Steel Grades Bjtp24 And Bjts40, Nuraziz Handika, Ridha Amalia Idhar, Jessica Sjah, Essy Arijoeni, Elly Tjahjono

Makara Journal of Technology

According to the current applicable national standard in Indonesia, i.e. SNI 07 2529 1991, in addition to the limitation on the loading rate, the steel bar must be reduced, formed, or lathed, as part of the shaping process of samples. This study determined and compared the effect of the shaping process on the yield strength, ultimate strength, and percent elongation by conducting tensile tests of steel bar grade BJTS40, i.e. deformed bar type of steel, and grade BJTP24, i.e., plain bar type of steel. Three diameters of the deformed bar (BJTS40) and one diameter of the plain bar (BJTP24) were …

Ionic Conductiviy Of Alginate-Nh4cl Polymer Electrolyte, Nurhasniza Mamajan Khan, Noor Saadiah Mohd Ali, Ahmad Faizrin Ahmad Fuzlin, Ahmad Salihin Samsudin

Makara Journal of Technology

This study aims to produce a solid biopolymer electrolyte (SBE) by doping ammonium chloride (NH4Cl) into alginate. Solution casting was used to prepare the alginate–NH4Cl SBE system. Electrical impedance spectroscopy was performed to analyze the electrical properties of the SBE under the applied frequency range of 50 Hz–1 MHz. The incorporation of 8 wt.% NH4Cl enhances the ionic conductivity of the SBE up to 3.18 × 10-7 S/cm at ambient room temperature. Fourier transform infrared spectroscopy shows that complexation occurs between the hydroxyl (-OH), carboxylate (COO-) and ether linkage (C-O-C) functional groups due to the formation of inter- and intra-molecular …

A Density Functional Theory Study On Using Montmorillonite To Reduce Air Pollution, Triati Dewi Kencana Wungu, Meqorry Yusfi, Suprijadi Suprijadi

Makara Journal of Technology

In this study, density functional theory (DFT) method is used to investigate the possibility of using a smectite clay mineral called montmorillonite (MMT) in reducing heavy metals, such as Cd, through Cd adsorption. The mechanism of Cd adsorption in MMT is observed theoretically, and the tetrahedrally isomorphic substitution on the upper layer of MMT is considered to observe the role of Al and Fe in strengthening Cd adsorption. Two types of MMT are modeled in this study: Al-MMT and Fe-MMT. The Al-MMT means that Al substitutes one atom in the upper tetrahedral layer of MMT, while Fe-MMT means that Fe …

Influence Of Lithium Bromide On Electrical Properties In Bio-Based Polymer Electrolytes, Ahmad Faizrin Fuzlin, Bouchta Sahraoui, Ahmad Salihin Samsudin

Makara Journal of Technology

This research presents the influence of lithium bromide (LiBr) on the electrical properties of alginate in bio-based polymer electrolytes (BBPEs) system. Bio-based alginate was prepared using the solution casting technique with various LiBr compositions. The ionic conductivity and electrical properties of the prepared BBPEs samples were studied using electrical impedance spectroscopy over a frequency range of 50 Hz–1 MHz. A maximum ionic conductivity of 7.46 × 10−5 S cm-1 was obtained for a sample containing 15 wt. % lithium bromide-doped alginate BBPEs at ambient temperature (303 K). The electrical analysis revealed that the most conductive sample based on alginate-LiBr BBPEs …

Use Of Viscoplastic Damper For Improving The Resistance Of Steel Frames To Blast Loading, Gholamreza Abdollahzadeh, Hadi Faghihmaleki, Hamed Hamidi Jamnani, Atefeh Ebrahimi Bardar

Makara Journal of Technology

In this paper, we evaluated the effect of viscoplastic dampers on the response of steel frames under blast loading. We used SAP2000 software and link elements to investigate the responses of nine-story steel frames with and without dampers. The proposed viscoplastic damper is a new type of viscous damper. The application of this damper is based on the availability of its constituent materials. The damper acts as a viscoelastic damper at low levels of vibration, but it acts as a combination of viscoelastic operator and metal-yielding device at extreme levels of vibration. With respect to the height of the structure, …

Antenna Radiation Element Designs For 5g Applications, Zhijun Gui

Electrical Engineering Undergraduate Honors Theses

This thesis introduced the advantage of the fifth-generation network and gave examples to the three major classes of applications categorized by International Telecommunication Union-Radiocommunication Sector. In this work, a patch antenna and a board-band bow-tie antenna with microelectromechanical switch design were modified to meet 5G communication purposes. The revised patch antenna produced a minimum S11 of -57.92dB, a resonant frequency at the 28GHz, and bandwidth of 4.55GHz. The modified design meets the requirements for wireless communication purposes. During the duplication process of the board-band bow-tie antenna design, multiple discrepancies were found, and the proposed results were not able to achieve. …

Design, Fabrication, And Reliability Effects Of Additively Manufactured First Level Compliant Interconnects For Microelectronics Application, Tumininu David Olatunji

Graduate Theses and Dissertations

Semiconductor packaging and development is greatly dependent on the magnitude of interconnect and on-chip stress that ultimately limits the reliability of electronic components. Thermomechanical related strains occur because of the coefficient of thermal expansion mismatch from different conjoined materials being assembled to manufacture a device. To curb the effect of thermal expansion mismatch between conjoined parts, studies have been done in integrating compliant structures between dies, solder balls, and substrates. Initial studies have enabled the design and manufacturing of these structures using a photolithography approach which involves a high number of fabrication steps depending on the complexity of the structures …

Transfer-To-Transfer Learning Approach For Computer Aided Detection Of Covid-19 In Chest Radiographs, Barath Narayanan Narayanan, Russell C. Hardie, Vignesh Krishnaraja, Christina Karam, Venkata Salini Priyamvada Davuluru

Electrical and Computer Engineering Faculty Publications

The coronavirus disease 2019 (COVID-19) global pandemic has severely impacted lives across the globe. Respiratory disorders in COVID-19 patients are caused by lung opacities similar to viral pneumonia. A Computer-Aided Detection (CAD) system for the detection of COVID-19 using chest radiographs would provide a second opinion for radiologists. For this research, we utilize publicly available datasets that have been marked by radiologists into two-classes (COVID-19 and non-COVID-19). We address the class imbalance problem associated with the training dataset by proposing a novel transfer-to-transfer learning approach, where we break a highly imbalanced training dataset into a group of balanced mini-sets and …

Programmable Battery Management System, Jason Erbert

Electrical Engineering

Lithium batteries provide excellent energy storage capabilities at a relatively high density; however, precautions must be taken with these high energy devices to ensure safe operation. A battery management system (BMS) provides protection by monitoring cell and pack voltage levels and maintaining them in a specific range. They limit the output current and disable the output in extreme conditions. Most devices in the targeted power range (<1000W) do not allow the user to manipulate the values for maximum current, cut-off voltage, or other limits. This project introduces the Programmable BMS (PBMS), which instead allows the user to select these values through a physical interface. The interface displays measurements including pack voltage and output current, and it reports additional characteristics of interest such as the battery’s temperature, state of charge, and cumulative number of charge cycles. This level of access and control permits users to receive the maximum performance and safety from common lithium battery packs.

Fractional Order Identification Method And Control: Development Of Control For Non-Minimum Phase Fractional Order System, Majid Abdullah Alhomim

Graduate Theses and Dissertations

The increasing use of renewable energy has resulted in the need for improved a dc-dc converters. This type of electronic-based equipment is needed to interface the dc voltages normally encountered with solar arrays and battery systems to voltage levels suitable for connecting three phase inverters to distribution level networks. As grid-connected solar power levels continue to increase, there is a corresponding need for improved modeling and control of power electronic converters. In particular, higher levels of boost ratios are needed to connect low voltage circuits (less than 1000 V) to medium voltage levels in the range of 13 kV to …

Smart Motor Syringe System, Conard Chan, Jenny Chiao

Electrical Engineering

Syringe pumps are widely used in many research applications especially in the applications that need precise control. Today most medical research utilizes syringes to control the fluid being pumped to the experiment objects. In most cases microscopic or nano-scopic motion control is required to acquire optimal results, such application includes purification of DNA/RNA from contaminants[1]. The high precision required to control the syringe pump makes it difficult to perform manually. This paper focuses on the design of an intelligent syringe pump motor control system to achieve reliable and precise control for biomedical experiments. This project improves medical research quality with …

Novel Memristor Based True Random Number Generator, Scott Stoller

Boise State University Theses and Dissertations

Random numbers are an important, but often overlooked part of the modern computing environment. They are used everywhere around us for a variety of purposes, from simple decision making in video games such as a coin toss, to securing financial transactions and encrypting confidential communications. They are even useful for gambling and the lottery.

Random numbers are generated in many ways. Pseudo random number generators (PRNGs) generate numbers based on a formula. True random number generators (TRNGs) capture entropy from the environment to generate randomness. As our society and our devices become more connected in the digital world, it is …

Simulation Of An Sp8t 18 Ghz Rf Switch Using Smt Pin Diodes, Andre De Souza Vigano

Master's Theses

Radio frequency (RF) and microwave switches are widely used in several different applications including radar, measurement systems, telecommunications, and other areas. An RF switch can control a radar’s transmit vs. receive mode, select the operating band, or direct an RF signal to different paths. In this study, a single pole eight throw (SP8T) switch using only Surface Mount (SMT) components is designed and simulated in Keysight’s Advanced Design System (ADS). Single pole eight throw is defined as one input and eight possible outputs. A star network configuration with series-shunt PIN diode switches is used to create the 8-way RF switch. …